path: root/MIBS/nokia/ALCATEL-IND1-PORT-MIB

ALCATEL-IND1-PORT-MIB DEFINITIONS ::= BEGIN

IMPORTS
	OBJECT-TYPE, Counter64,
        NOTIFICATION-TYPE, MODULE-IDENTITY,
	TimeTicks, Integer32              FROM SNMPv2-SMI
        MODULE-COMPLIANCE, OBJECT-GROUP,
        NOTIFICATION-GROUP                FROM SNMPv2-CONF
        ifIndex, ifInErrors, ifOutErrors
					  FROM IF-MIB
	softentIND1Port, cmmEsmDrvTraps
			   		  FROM ALCATEL-IND1-BASE
	DisplayString            FROM SNMPv2-TC;

alcatelIND1PortMIB MODULE-IDENTITY

   LAST-UPDATED  "200704030000Z"
   ORGANIZATION  "Alcatel-Lucent"
   CONTACT-INFO
        "Please consult with Customer Service to ensure the most appropriate
         version of this document is used with the products in question:

                    Alcatel-Lucent, Enterprise Solutions Division
                   (Formerly Alcatel Internetworking, Incorporated)
                           26801 West Agoura Road
                        Agoura Hills, CA  91301-5122
                          United States Of America

        Telephone:               North America  +1 800 995 2696
                                 Latin America  +1 877 919 9526
                                 Europe         +31 23 556 0100
                                 Asia           +65 394 7933
                                 All Other      +1 818 878 4507

        Electronic Mail:         support@ind.alcatel.com
        World Wide Web:          http://alcatel-lucent.com/wps/portal/enterprise
        File Transfer Protocol:  ftp://ftp.ind.alcatel.com/pub/products/mibs"

    DESCRIPTION
        "This module describes an authoritative enterprise-specific Simple
         Network Management Protocol (SNMP) Management Information Base (MIB):

             This group contains the configuration information data
			for the Ethernet Switching Module.

         The right to make changes in specification and other information
         contained in this document without prior notice is reserved.

         No liability shall be assumed for any incidental, indirect, special, or
         consequential damages whatsoever arising from or related to this
         document or the information contained herein.

         Vendors, end-users, and other interested parties are granted
         non-exclusive license to use this specification in connection with
         management of the products for which it is intended to be used.

                     Copyright (C) 1995-2007 Alcatel-Lucent
                         ALL RIGHTS RESERVED WORLDWIDE"

    REVISION      "200704030000Z"
    DESCRIPTION
        "The latest version of this MIB Module."

    ::= { softentIND1Port 1}

alcatelIND1PortNotifications	OBJECT IDENTIFIER ::= { alcatelIND1PortMIB 0 }
alcatelIND1PortMIBObjects 		OBJECT IDENTIFIER ::= { alcatelIND1PortMIB 1 }
alcatelIND1PortMIBConformance		OBJECT IDENTIFIER ::= { alcatelIND1PortMIB 2 }

--
-- alcatelIND1PortMIBObjects
--

esmConfTrap						OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 1 }
physicalPort					OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 2 }
ddmConfiguration				OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 4 }
ddmNotifications				OBJECT IDENTIFIER ::= { alcatelIND1PortNotifications 1 }
esmViolationRecovery				OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 5 }
esmViolationNotifications                       OBJECT IDENTIFIER ::= { alcatelIND1PortNotifications 2 } 

-- Ethernet Driver object related to Trap *********************

esmDrvTrapDrops   OBJECT-TYPE
	SYNTAX  Integer32
	MAX-ACCESS  read-only
	STATUS  current
	DESCRIPTION "Partitioned port (separated due to errors)."
	::= { esmConfTrap 1 }

-- Ethernet Driver Tables *****************************

        --  EsmConf group.  This group contains the configuration
        --  information data for the Ethernet Switching Module.
        --  Implementation of this group is mandantory.
        --
        --  Note that this MIB can NOT be used for row creation (this
        --  would imply that you could override the actual physical
        --  characteristics of the physical card!).

        esmConfTable  OBJECT-TYPE
            SYNTAX  SEQUENCE OF EsmConfEntry
            MAX-ACCESS  not-accessible
            STATUS  current
            DESCRIPTION
                "A list of ESM Physical Port instances."
            ::= { physicalPort 1 }

        esmConfEntry  OBJECT-TYPE
            SYNTAX  EsmConfEntry
            MAX-ACCESS  not-accessible
            STATUS  current
            DESCRIPTION
                "A ESM Physical Port entry."
            INDEX { ifIndex }
            ::= { esmConfTable 1 }

        EsmConfEntry ::= SEQUENCE {
	    esmPortSlot
	        Integer32,
	    esmPortIF
	        Integer32,
            esmPortAutoSpeed
                INTEGER,
            esmPortAutoDuplexMode
                INTEGER,
            esmPortCfgSpeed
                INTEGER,
            esmPortCfgDuplexMode
                INTEGER,
            esmPortCfgIFG
                Integer32,
            esmPortPauseSlotTime
                Integer32,
            esmPortMaxFloodRate
                INTEGER,
            esmPortFloodMcastEnable
                INTEGER,
            esmPortCfgMaxFrameSize
                Integer32,
            esmPortCfgLongEnable
                INTEGER,
            esmPortCfgRuntEnable
                INTEGER,
            esmPortCfgRuntSize
                Integer32,
	    esmPortCfgAutoNegotiation
			INTEGER,
	    esmPortCfgCrossover
			INTEGER,
	    esmPortCfgFlow
			INTEGER,
	    esmPortCfgHybridActiveType
	    		INTEGER,
	    esmPortCfgHybridMode
	    		INTEGER,
            esmPortOperationalHybridType
                        INTEGER,
            esmPortCfgMMULowWaterMarkCellSetLimit
                	INTEGER,
            esmPortCfgMMUDynamicCellSetLimit
                	INTEGER,
            esmPortViolationBitMap
                        BITS,
            esmPortViolationClearAll
                        INTEGER,
	    esmPortFloodBcastEnable
		INTEGER,
	    esmPortFloodUnknownUcastEnable
		INTEGER,
	    esmPortMaxUnknownUcastFloodRate
		INTEGER,
	    esmPortMaxMcastFloodRate
		INTEGER,
	    esmPortMaxFloodRateLimit
		Integer32,
	    esmPortMaxUnknownUcastFloodRateLimit
		Integer32,
	    esmPortMaxMcastFloodRateLimit
		Integer32,
	    esmPortCfgSFPType
		DisplayString 
            }

        esmPortSlot OBJECT-TYPE
            SYNTAX Integer32
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
            "The physical Slot number for this Ethernet Port.
	     Slot number has been added to be used by the private Trap."
        ::= { esmConfEntry 1 }

        esmPortIF OBJECT-TYPE
            SYNTAX Integer32
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
            "The on-board interface number for this Ethernet Port.
	     Port Number has been added to be used by the private Trap."
        ::= { esmConfEntry 2 }

        esmPortAutoSpeed OBJECT-TYPE
            SYNTAX INTEGER {
                speed100(1),
                speed10(2),
                speedAuto(3),
                unknown(4),
                speed1000(5),
	        speed10000(6)
            }
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
            "The automatically detected port line speed
             of this ESM port."
        ::= { esmConfEntry 3 }

        esmPortAutoDuplexMode OBJECT-TYPE
            SYNTAX INTEGER {
                fullDuplex(1),
                halfDuplex(2),
                autoDuplex(3),
                unknown(4)
            }
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
            "The automatically detected port duplex mode
             of this ESM port.

	     Note: GigaEthernet supports only Full duplex mode.
	           Default value for 10/100 = Half duplex mode."
        ::= { esmConfEntry 4 }

        esmPortCfgSpeed OBJECT-TYPE
            SYNTAX INTEGER {
                speed100(1),
                speed10(2),
                speedAuto(3),
                speed1000(5),
	        speed10000(6),
	        speedMax100(8),
		speedMax1000(9)
            }
            MAX-ACCESS read-write
            STATUS current
            DESCRIPTION
            "The configured port line speed of this ESM port."
        ::= { esmConfEntry 5 }

        esmPortCfgDuplexMode OBJECT-TYPE
            SYNTAX INTEGER {
                fullDuplex(1),
                halfDuplex(2),
                autoDuplex(3)
            }
            MAX-ACCESS read-write
            STATUS current
            DESCRIPTION
            "The configured port duplex mode of this ESM port.
            Note: GigaEthernet support only full-duplex."
        ::= { esmConfEntry 6 }

        esmPortCfgIFG OBJECT-TYPE
            SYNTAX Integer32
            MAX-ACCESS read-write
            STATUS current
            DESCRIPTION
            "Contains the setting of Inter-Frame Gap (IFG), in bytes
            for receive and transmit.
	    The range is from 9 to 12 bytes.

	    Note: The default value changed according to the Port type
	    Default    Bandwidth    value
	    12 bytes    10Mbps       9600 nsec
	               100Mbps        960 nsec
	 	         1Gbps         96 nsec
			10Gbps        9.6 nsec."
	    DEFVAL { 12 }
        ::= { esmConfEntry 7 }

        esmPortPauseSlotTime OBJECT-TYPE
            SYNTAX Integer32
            MAX-ACCESS read-write
            STATUS current
            DESCRIPTION
            "Indicates the number of microseconds the other
             end-station waits after the reception
             of a pause frame.

	     Note: Pause Flow control is not available for 10Mbps.
	           For 100Mbps, the possible value range is
		   5120 nanosec to 0.3 sec.
	   	   For 1Gbps, the possible value range is
		   512 nanosec to 0.03 sec."
        ::= { esmConfEntry 8 }

        esmPortMaxFloodRate    OBJECT-TYPE
            SYNTAX INTEGER {
                      mbps(1),
                      percentage(2),
		      pps(3)
                   }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Broadcast flood threshold type. To set the type, set esmPortMaxFloodRateLimit also."
	    DEFVAL { mbps }
          ::= { esmConfEntry 9 }

        esmPortFloodMcastEnable    OBJECT-TYPE
            SYNTAX INTEGER {
                      disableMulticastFlood(2),
                      enableMulticastFlood(1)
                   }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Enable/disable the maximum flood rate
                  for multicast."
	    DEFVAL { disableMulticastFlood }
          ::= { esmConfEntry 10 }

        esmPortCfgMaxFrameSize   OBJECT-TYPE
            SYNTAX Integer32
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Configure the value of the maximum frame
                  size allow.
		  For 10/100:
		  It is a range between 1518(untagged) and 1553 bytes.
		  For GigaEthernet:
	          It is a range between 1518 and 10240 bytes.(OS7700,OS7800,OS8800)
                  It is a range between 1518 and 9216 bytes.(OS6800)"
          ::= { esmConfEntry 11 }

        esmPortCfgLongEnable   OBJECT-TYPE
            SYNTAX INTEGER {
                disable(0),
                enable(1)
            }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Allow the user to change the maximun Frame size.
                  Note: It is not configurable for 10/100 Ethernet port."
	    DEFVAL { disable }
          ::= { esmConfEntry 12 }

        esmPortCfgRuntEnable   OBJECT-TYPE
            SYNTAX INTEGER {
                disable(2),
                enable(3)
            }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Allow the user to change the minimum Frame size."
	    DEFVAL { disable }
          ::= { esmConfEntry 13 }

        esmPortCfgRuntSize   OBJECT-TYPE
            SYNTAX Integer32
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Configure the value of the minimum frame
                  size allow per ports.
		  The range is 0 to 64."
	    DEFVAL { 64 }
          ::= { esmConfEntry 14 }

        esmPortCfgAutoNegotiation   OBJECT-TYPE
            SYNTAX INTEGER {
                enable(1),
                disable(2)
            }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Allow the user to enable or disable the port auto negotiation."
	    DEFVAL { disable }
          ::= { esmConfEntry 15 }

        esmPortCfgCrossover   OBJECT-TYPE
            SYNTAX INTEGER {
                	mdi(1),
                	mdix(2),
			auto(3)
            }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Allow the user to configure port crossover."
	    DEFVAL { auto }
          ::= { esmConfEntry 16 }

        esmPortCfgFlow   OBJECT-TYPE
            SYNTAX INTEGER {
                enable(1),
                disable(2)
            }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Use the dot3PauseAdminMode from the standard MIB to configure the flow control."
	    DEFVAL { disable }
          ::= { esmConfEntry 17 }

 	esmPortCfgHybridActiveType OBJECT-TYPE
            SYNTAX INTEGER {
                notapplicable(0),
                fiber(1),
                copper(2)
            }
            MAX-ACCESS  read-only
            STATUS  current
            DESCRIPTION
                 "This object is only applicable to hybrid ports .
                  It indicates configured active media type.(the operational media
                  type may be different if esmPortCfgHybridMode is configured to be
                  preferredFiber or preferredCopper)
                  For non hybrid ports notapplicable is returned as a status."
          ::= { esmConfEntry 18 }

	esmPortCfgHybridMode OBJECT-TYPE
            SYNTAX INTEGER {
                notapplicable(0),
                preferredCopper(1),
                forcedCopper(2),
                preferredFiber(3),
                forcedFiber(4)
            }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "This object is only applicable to hybrid ports. 
                  This allows the user the user to configure the media type
                  with which the port should come up. 
                  The user can configure the port to come as copper only 
                  or fiber only or either fiber/copper 
                  (with preference to one of them)."
	    DEFVAL { preferredFiber }
          ::= { esmConfEntry 19 }

 	esmPortOperationalHybridType OBJECT-TYPE
            SYNTAX INTEGER {
		none(0),
                fiber(1),
                copper(2)
            }
            MAX-ACCESS  read-only
            STATUS  current
            DESCRIPTION
                 "This object is only applicable to hybrid ports .
                  It indicates  the actual media type that has link up and is or will be
                  passing traffic. If link is not present the object will return none(0) value."
          ::= { esmConfEntry 20 }

	esmPortCfgMMULowWaterMarkCellSetLimit OBJECT-TYPE
	    SYNTAX INTEGER (0..16383)
	    MAX-ACCESS read-write
	    STATUS current
	    DESCRIPTION
		" Per-port-per-CoS Head of Line blocking cell limits. Range is 0 - 16383
		  Firebolt register Offset: 0x006pp30 - 0x37
		  Bits: 13:0 CellSetLimit , Default: 0x0100
		  This setting allocates the guaranteed cells for one port's CoSx queue.
		  After cell count over this limit, it will start using dynamic cells in
		  port dynamic space."
	    DEFVAL { 256 }
	  ::= { esmConfEntry 21 }

	esmPortCfgMMUDynamicCellSetLimit OBJECT-TYPE
	    SYNTAX INTEGER (0..16383)
	    MAX-ACCESS read-write
	    STATUS current
	    DESCRIPTION
		"Per-egress port cell-based dynamic (shared buffer pool) memory
		usage drop and resume thresholds. This sets the limit for which
		the eight CoS-Qs within a port may share once the LWMCOSCELL
		limit is exceeded. Range is 0 - 16383
		Firebolt register Offset: 0x006pp040
		Bits: 13:0 Dynamic CellSetLimit , 
                Chip Default: 0x0400 (1024).
                The system default value for Dynamic CellSetLimit is 0x100 (256)."
	    DEFVAL { 1024 }
	  ::= { esmConfEntry 22 }



	esmPortViolationBitMap OBJECT-TYPE
          SYNTAX      BITS{
              bEniSecurityBlockPortENI(0),         -- ENI App blocking this port
              bEniSecurityBlockPortSTP(1),         -- STP App blocking this port
 	      bEniSecurityBlockPortSL(2),          -- SL App blocking this port
	      bEniSecurityBlockPortQoS(3),         -- QoS App blocking this port
 	      bEniSecurityBlockPortUDLD(4),        -- UDLD App blocking this port
	      bEniSecurityBlockPortETHBLK(5)       -- ETHBLK App blocking this port
          }
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "A bit map that identifies the set of Application that have blocked 
                       a port as a result of a particular violation "

          ::= { esmConfEntry 23 }

      esmPortViolationClearAll OBJECT-TYPE
          SYNTAX      INTEGER(0) 
          MAX-ACCESS  read-write
          STATUS      current
          DESCRIPTION "Clear all port vioaltion "

          ::= { esmConfEntry 24 }


	esmPortFloodBcastEnable    OBJECT-TYPE
            SYNTAX INTEGER {
                      disableBcastFlood(2),
                      enableBcastFlood(1)
                   }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Enable/disable the maximum flood rate
                  for Broadcast."
	    DEFVAL { enableBcastFlood }
          ::= { esmConfEntry 25 }

	esmPortFloodUnknownUcastEnable    OBJECT-TYPE
            SYNTAX INTEGER {
                      disableUnknownUcastFlood(2),
                      enableUnknownUcastFlood(1)
                   }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Enable/disable the maximum flood rate
                  for unknown unicast."
	    DEFVAL { enableUnknownUcastFlood }
          ::= { esmConfEntry 26 }

	esmPortMaxUnknownUcastFloodRate    OBJECT-TYPE
            SYNTAX INTEGER {
                      mbps(1),
                      percentage(2),
		      pps(3)
                   }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Unknown-Unicast flood threshold type. To set the type, set esmPortMaxUnknownUcastFloodRateLimit also"
	    DEFVAL { mbps }
          ::= { esmConfEntry 27 }

	esmPortMaxMcastFloodRate    OBJECT-TYPE
            SYNTAX INTEGER {
                      mbps(1),
                      percentage(2),
		      pps(3)
                   }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Multicast flood threshold type. To set the type, set esmPortMaxFloodRateLimit also."
	    DEFVAL { mbps }
          ::= { esmConfEntry 28 }

	esmPortMaxFloodRateLimit    OBJECT-TYPE
            SYNTAX  Integer32
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "The value of the maximum broadcast flood limit.
		  The actual range of the flood limit depends on the port speed.
		     example:	
		     Percentage: 1 - 100
		     Mbps: 1 - 1000 (1G speed)
		     PPS: 244 - 244262 (1G speed)
		  To set the limit, set esmPortMaxFloodRate first" 
          ::= { esmConfEntry 29 }


	esmPortMaxUnknownUcastFloodRateLimit    OBJECT-TYPE
            SYNTAX  Integer32
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "The value of the maximum unknown-unicast flood limit
		  The actual range of the flood limit depends on the port speed.
		     example:	
		     Percentage: 1 - 100
		     Mbps: 1 - 1000 (1G speed)
		     PPS: 244 - 244262 (1G speed)
		  To set the limit, set esmPortMaxUnknownUcastFloodRate first"
          ::= { esmConfEntry 30 }

       esmPortMaxMcastFloodRateLimit    OBJECT-TYPE
            SYNTAX  Integer32
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "The value of the maximum multicast flood limit
		  The actual range of the flood limit depends on the port speed.
		     example:	
		     Percentage: 1 - 100
		     Mbps: 1 - 1000 (1G speed)
		     PPS: 244 - 244262 (1G speed)
		  To set the limit, set esmPortMaxMcastFloodRate first"
          ::= { esmConfEntry 31 }

       esmPortCfgSFPType OBJECT-TYPE   
            SYNTAX      DisplayString (SIZE (0..64))   
            MAX-ACCESS read-only   
            STATUS      current   
            DESCRIPTION   
                 "This object is only applicable to fiber ports.   
                  The string indicates the type of SFP/GBIC of active media."   
          ::= {  esmConfEntry 32 }  

    

-- Ethernet Port Mode Tables *****************************
        --  EsmPortMode group.  This group contains the configuration
        --  information data for the Ethernet Switching Module.
        --  Implementation of this group is mandantory.
        --
        --  Note that this MIB can NOT be used for row creation (this
        --  would imply that you could override the actual physical
        --  characteristics of the physical card!).

        esmPortModeTable  OBJECT-TYPE
            SYNTAX  SEQUENCE OF EsmPortModeEntry
            MAX-ACCESS  not-accessible
            STATUS  current
            DESCRIPTION
                "A list of ESM Physical Port Mode instances."
            ::= { physicalPort 6 }

        esmPortModeEntry  OBJECT-TYPE
            SYNTAX  EsmPortModeEntry
            MAX-ACCESS  not-accessible
            STATUS  current
            DESCRIPTION
                "A ESM Physical Port Mode entry."
            INDEX { esmPortModeIndex }
            ::= { esmPortModeTable 1 }

        EsmPortModeEntry ::= SEQUENCE {
	    esmPortModeIndex
		INTEGER,
            esmPortRunningMode
                INTEGER,
            esmPortSavedMode
                INTEGER
            }

	esmPortModeIndex OBJECT-TYPE
	    SYNTAX INTEGER (1001..8128)
	    MAX-ACCESS not-accessible
	    STATUS current
	    DESCRIPTION
	    "Valid ni/port values"
	::= { esmPortModeEntry 1 }

        esmPortRunningMode OBJECT-TYPE
            SYNTAX INTEGER {
                uplink(1),
                stackable(2)
            }
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
            "Currently configured Etna port 25,26 as 10G uplink user port or stacking port.
             Default is uplink 10G port. User can not set the current mode."
        ::= { esmPortModeEntry 2 }

        esmPortSavedMode OBJECT-TYPE
            SYNTAX INTEGER {
                uplink(1),
                stackable(2)
            }
            MAX-ACCESS read-write
            STATUS current
            DESCRIPTION
            "Next configured Etna port 25,26 as 10G uplink user port or stacking port.
             At boot up, it has the same value as current esmPortRunningMode. It takes some time to
             write to the EEPROM. Have at least more than 7 sec between each write operation"
        ::= { esmPortModeEntry 3 }

          -- The Ethernet Statistics Group
          --
          -- The ethernet statistics group contains statistics
          -- measured by the probe for each monitored interface on
          -- this device.  These statistics take the form of free
          -- running counters that start from zero when a valid entry
          -- is created.
          --
          -- This group currently has statistics defined only for
          -- Ethernet interfaces.  Each alcetherStatsEntry contains
          -- statistics for one Ethernet interface.  The probe must
          -- create one alcetherStats entry for each monitored Ethernet
          -- interface on the device.

          alcetherStatsTable OBJECT-TYPE
              SYNTAX SEQUENCE OF AlcetherStatsEntry
              MAX-ACCESS not-accessible
              STATUS current
              DESCRIPTION
                  "A list of Ethernet statistics entries."
              ::= { physicalPort 2 }

          alcetherStatsEntry OBJECT-TYPE
              SYNTAX AlcetherStatsEntry
              MAX-ACCESS not-accessible
              STATUS current
              DESCRIPTION
                  "A collection of statistics kept for a particular
                  Ethernet interface.  As an example, an instance of the
                  etherStatsPkts object might be named alcetherStatsPkts.1"
              INDEX { ifIndex }
              ::= { alcetherStatsTable 1 }

          AlcetherStatsEntry ::= SEQUENCE {
	      alcetherClearStats		    INTEGER,
	      alcetherLastClearStats                TimeTicks,
              alcetherStatsCRCAlignErrors           Counter64,
              alcetherStatsRxUndersizePkts          Counter64,
              alcetherStatsTxUndersizePkts          Counter64,
              alcetherStatsTxOversizePkts           Counter64,
              alcetherStatsRxJabbers                Counter64,
              alcetherStatsRxCollisions             Counter64,
              alcetherStatsTxCollisions             Counter64,
              alcetherStatsPkts64Octets             Counter64,
              alcetherStatsPkts65to127Octets        Counter64,
              alcetherStatsPkts128to255Octets       Counter64,
              alcetherStatsPkts256to511Octets       Counter64,
              alcetherStatsPkts512to1023Octets      Counter64,
              alcetherStatsPkts1024to1518Octets     Counter64,
              gigaEtherStatsPkts1519to4095Octets    Counter64,
              gigaEtherStatsPkts4096to9215Octets    Counter64,
		alcetherStatsPkts1519to2047Octets 	Counter64,
		alcetherStatsPkts2048to4095Octets 	Counter64,
		alcetherStatsPkts4096Octets 		Counter64,
		alcetherStatsRxGiantPkts 		Counter64,
		alcetherStatsRxDribbleNibblePkts 	Counter64,
		alcetherStatsRxLongEventPkts 		Counter64,
		alcetherStatsRxVlanTagPkts 		Counter64,
		alcetherStatsRxControlPkts 		Counter64,
		alcetherStatsRxLenChkErrPkts 		Counter64,
		alcetherStatsRxCodeErrPkts 		Counter64,
		alcetherStatsRxDvEventPkts 		Counter64,
		alcetherStatsRxPrevPktDropped 	Counter64,
		alcetherStatsTx64Octets 		Counter64,
		alcetherStatsTx65to127Octets 		Counter64,
		alcetherStatsTx128to255Octets 	Counter64,
		alcetherStatsTx256to511Octets 	Counter64,
		alcetherStatsTx512to1023Octets 	Counter64,
		alcetherStatsTx1024to1518Octets 	Counter64,
		alcetherStatsTx1519to2047Octets 	Counter64,
		alcetherStatsTx2048to4095Octets 	Counter64,
		alcetherStatsTx4096Octets 		Counter64,
		alcetherStatsTxRetryCount 		Counter64,
		alcetherStatsTxVlanTagPkts 		Counter64,
		alcetherStatsTxControlPkts 		Counter64,
		alcetherStatsTxLatePkts 		Counter64,
		alcetherStatsTxTotalBytesOnWire 	Counter64,
		alcetherStatsTxLenChkErrPkts 		Counter64,
		alcetherStatsTxExcDeferPkts		Counter64
		}

          alcetherClearStats OBJECT-TYPE
              SYNTAX INTEGER
		{	default(0),
	 		reset(1)
		}
              MAX-ACCESS read-write
              STATUS current
              DESCRIPTION
                  "Used to Clear all Statistics counters.
		   By default, this object contains zero value."
              ::= { alcetherStatsEntry 1 }

          alcetherLastClearStats OBJECT-TYPE
              SYNTAX TimeTicks
	      MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The value of SysUpTime at the time of all
		   the statistics counters are cleared.
		   By default, this object contains a zero value."
              ::= { alcetherStatsEntry 2 }

          alcetherStatsCRCAlignErrors OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of packets received that
                  had a length (excluding framing bits, but
                  including FCS octets) of between 64 and 1518
                  octets, inclusive, but but had either a bad
                  Frame Check Sequence (FCS) with an integral
                  number of octets (FCS Error) or a bad FCS with
                  a non-integral number of octets (Alignment Error)."
              ::= { alcetherStatsEntry 3 }

          alcetherStatsRxUndersizePkts OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of packets received that were
                  less than 64 octets long (excluding framing bits,
                  but including FCS octets) and were otherwise well
                  formed."
              ::= { alcetherStatsEntry 4 }

          alcetherStatsTxUndersizePkts OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of packets transmitted that were
                  less than 64 octets long (excluding framing bits,
                  but including FCS octets) and were otherwise well
                  formed."
              ::= { alcetherStatsEntry 5 }

          alcetherStatsTxOversizePkts OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of packets transmitted that were
                  longer than 1518 octets long (excluding framing bits,
                  but including FCS octets) and were otherwise well
                  formed."
              ::= { alcetherStatsEntry 6 }

          alcetherStatsRxJabbers OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of packets received that were
                  longer than 1518 octets (excluding framing bits,
                  but including FCS octets), and had either a bad
                  Frame Check Sequence (FCS) with an integral number
                  of octets (FCS Error) or a bad FCS with a
                  non-integral number of octets (Alignment Error).

                  Note that this definition of jabber is different
                  than the definition in IEEE-802.3 section 8.2.1.5
                  (10BASE5) and section 10.3.1.4 (10BASE2).  These
                  documents define jabber as the condition where any
                  packet exceeds 20 ms.  The allowed range to detect
                  jabber is between 20 ms and 150 ms."
              ::= { alcetherStatsEntry 7 }

          alcetherStatsRxCollisions OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The best estimate of the total number of collisions
                  on this Ethernet segment (in reception).
		  Only for Ethernet Interfaces.

                  The value returned will depend on the location of
                  the RMON probe. Section 8.2.1.3 (10BASE-5) and
                  section 10.3.1.3 (10BASE-2) of IEEE standard 802.3
                  states that a station must detect a collision, in
                  the receive mode, if three or more stations are
                  transmitting simultaneously.  A repeater port must
                  detect a collision when two or more stations are
                  transmitting simultaneously.  Thus a probe placed on
                  a repeater port could record more collisions than a
                  probe connected to a station on the same segment
                  would.

                  Probe location plays a much smaller role when
                  considering 10BASE-T.  14.2.1.4 (10BASE-T) of IEEE
                  standard 802.3 defines a collision as the
                  simultaneous presence of signals on the DO and RD
                  circuits (transmitting and receiving at the same
                  time).  A 10BASE-T station can only detect
                  collisions when it is transmitting.  Thus probes
                  placed on a station and a repeater, should report
                  the same number of collisions.

                  Note also that an RMON probe inside a repeater
                  should ideally report collisions between the
                  repeater and one or more other hosts (transmit
                  collisions as defined by IEEE 802.3k) plus receiver
                  collisions observed on any coax segments to which
                  the repeater is connected."
              ::= { alcetherStatsEntry 8 }

          alcetherStatsTxCollisions OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The best estimate of the total number of collisions
                  on this Ethernet segment (in transmition).
		  Only for Ethernet Interfaces.

                  The value returned will depend on the location of
                  the RMON probe. Section 8.2.1.3 (10BASE-5) and
                  section 10.3.1.3 (10BASE-2) of IEEE standard 802.3
                  states that a station must detect a collision, in
                  the receive mode, if three or more stations are
                  transmitting simultaneously.  A repeater port must
                  detect a collision when two or more stations are
                  transmitting simultaneously.  Thus a probe placed on
                  a repeater port could record more collisions than a
                  probe connected to a station on the same segment
                  would.

                  Probe location plays a much smaller role when
                  considering 10BASE-T.  14.2.1.4 (10BASE-T) of IEEE
                  standard 802.3 defines a collision as the
                  simultaneous presence of signals on the DO and RD
                  circuits (transmitting and receiving at the same
                  time).  A 10BASE-T station can only detect
                  collisions when it is transmitting.  Thus probes
                  placed on a station and a repeater, should report
                  the same number of collisions.

                  Note also that an RMON probe inside a repeater
                  should ideally report collisions between the
                  repeater and one or more other hosts (transmit
                  collisions as defined by IEEE 802.3k) plus receiver
                  collisions observed on any coax segments to which
                  the repeater is connected."
              ::= { alcetherStatsEntry 9 }

          alcetherStatsPkts64Octets OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of packets (including bad
                  packets) received that were 64 octets in length
                  (excluding framing bits but including FCS octets)."
              ::= { alcetherStatsEntry 10 }

          alcetherStatsPkts65to127Octets OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of packets (including bad
                  packets) received that were between
                  65 and 127 octets in length inclusive
                  (excluding framing bits but including FCS octets)."
              ::= { alcetherStatsEntry 11 }

          alcetherStatsPkts128to255Octets OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of packets (including bad
                  packets) received that were between
                  128 and 255 octets in length inclusive
                  (excluding framing bits but including FCS octets)."
              ::= { alcetherStatsEntry 12 }

          alcetherStatsPkts256to511Octets OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of packets (including bad
                  packets) received that were between
                  256 and 511 octets in length inclusive
                  (excluding framing bits but including FCS octets)."
              ::= { alcetherStatsEntry 13 }

          alcetherStatsPkts512to1023Octets OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of packets (including bad
                  packets) received that were between
                  512 and 1023 octets in length inclusive
                  (excluding framing bits but including FCS octets)."
              ::= { alcetherStatsEntry 14 }

          alcetherStatsPkts1024to1518Octets OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of packets (including bad
                  packets) received that were between
                  1024 and 1518 octets in length inclusive
                  (excluding framing bits but including FCS octets).
	          For both Ethernet and GigaEthernet."
              ::= { alcetherStatsEntry 15 }

          gigaEtherStatsPkts1519to4095Octets OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of packets (including bad
                  packets) received that were between
                  1519 and 4095 octets in length inclusive
                  (excluding framing bits but including FCS octets).
		  Only for GigaEthernet interfaces"
              ::= { alcetherStatsEntry 16 }

          gigaEtherStatsPkts4096to9215Octets OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of packets (including bad
                  packets) received that were between
                  4096 and 9215 octets in length inclusive
                  (excluding framing bits but including FCS octets).
		  Only for GigaEthernet interfaces"
              ::= { alcetherStatsEntry 17 }


		alcetherStatsPkts1519to2047Octets 	OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of frames(including error packets) received
		   that were between 1519 and 2047 bytes in length inclusive
		   (excluding framing bits but including FCS bytes).
		   "
              ::= { alcetherStatsEntry 18 }

		alcetherStatsPkts2048to4095Octets 	OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of frames(including error packets) received
		   that were between 2048 and 4095 bytes in length inclusive
		   (excluding framing bits but including FCS bytes).
		   "
              ::= { alcetherStatsEntry 19 }

		alcetherStatsPkts4096Octets 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of frames(including error packets) received
		   that were greater than or equal to 4096 bytes in length inclusive
		   (excluding framing bits but including FCS bytes).
		   "
              ::= { alcetherStatsEntry 20 }

		alcetherStatsRxGiantPkts 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of frames that are greater than the specified
		   Max length value, with a valid CRC, dropped because too long.
		   "
              ::= { alcetherStatsEntry 21 }

		alcetherStatsRxDribbleNibblePkts 	OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of frames for which a dribble nibble has been
		   received and CRC is correct.
		   "
              ::= { alcetherStatsEntry 22 }

		alcetherStatsRxLongEventPkts 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of frames for which the Carrier sense exceeds
		   50000 bit times for 10 Mbits/sec or 80000 bit times for
		   100 Mbits/sec."
              ::= { alcetherStatsEntry 23 }

		alcetherStatsRxVlanTagPkts 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of frames for which Type/Length field
		   contains the VLAN protocol identifier (0x8100). "
              ::= { alcetherStatsEntry 24 }

		alcetherStatsRxControlPkts 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of frames that were recognized as control frames."
              ::= { alcetherStatsEntry 25 }

		alcetherStatsRxLenChkErrPkts 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of frames for which the frame length field value
		   in the Type/Length field does not match the actual data bytes
		    length and is NOT a type field."
              ::= { alcetherStatsEntry 26 }

		alcetherStatsRxCodeErrPkts 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of frames for which one or more nibbles were
		   signaled as errors during reception of the frame."
              ::= { alcetherStatsEntry 27 }

		alcetherStatsRxDvEventPkts 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of frames for which a RX_DV event (packet not
		   too long enough to be valid packet) has been seen before the
		    correct frame."
              ::= { alcetherStatsEntry 28 }

		alcetherStatsRxPrevPktDropped 	OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of frames for which a packet has been dropped
		   (because of too small IFG) before the correct frame."
              ::= { alcetherStatsEntry 29 }

		alcetherStatsTx64Octets 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of transmitted frames of 64 bytes."
              ::= { alcetherStatsEntry 30 }

		alcetherStatsTx65to127Octets 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of transmitted frames that were between
		   65 and 127 bytes in length inclusive (excluding framing bits
		    but including FCS bytes)."
              ::= { alcetherStatsEntry 31 }

		alcetherStatsTx128to255Octets 	OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of transmitted frames that were between
		   128 and 255 bytes in length inclusive (excluding framing bits
		    but including FCS bytes)."
              ::= { alcetherStatsEntry 32 }

		alcetherStatsTx256to511Octets 	OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of transmitted frames that were between
		   256 and 511 bytes in length inclusive (excluding framing bits
		    but including FCS bytes)."
              ::= { alcetherStatsEntry 33 }

		alcetherStatsTx512to1023Octets 	OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of transmitted frames that were between
		   512 and 1023 bytes in length inclusive (excluding framing bits
		    but including FCS bytes)."
              ::= { alcetherStatsEntry 34 }

		alcetherStatsTx1024to1518Octets 	OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of transmitted frames that were between
		   1024 and 1518 bytes in length inclusive (excluding framing bits
		    but including FCS bytes)."
              ::= { alcetherStatsEntry 35 }

		alcetherStatsTx1519to2047Octets 	OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of transmitted frames that were between
		   1519 and 2047 bytes in length inclusive (excluding framing bits
		    but including FCS bytes)."
              ::= { alcetherStatsEntry 36 }

		alcetherStatsTx2048to4095Octets 	OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of transmitted frames that were between
		   2048 and 4095 bytes in length inclusive (excluding framing bits
		    but including FCS bytes)."
              ::= { alcetherStatsEntry 37 }

		alcetherStatsTx4096Octets 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of transmitted frames that were greater than
		    or equal to 4096 bytes in length and less than Max frame length
		    (excluding framing bits but including FCS bytes)."
              ::= { alcetherStatsEntry 38 }

		alcetherStatsTxRetryCount 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of collisions that the frames faced during
		   transmission attempts."
              ::= { alcetherStatsEntry 39 }

		alcetherStatsTxVlanTagPkts 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of transmitted frames for which Type/Length field contains the
		   VLAN protocol identifier (0x8100)."
              ::= { alcetherStatsEntry 40 }

		alcetherStatsTxControlPkts 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of transmitted frames that were recognised as control frames."
              ::= { alcetherStatsEntry 41 }

		alcetherStatsTxLatePkts 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of late collisions that occured beyond the collision window."
              ::= { alcetherStatsEntry 42 }

		alcetherStatsTxTotalBytesOnWire 	OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of bytes transmitted on wire, including all bytes from collided
		  attempts."
              ::= { alcetherStatsEntry 43 }

		alcetherStatsTxLenChkErrPkts 		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of transmitted frames for which the frame length field value
		  in the Type/Length field does not match the actual data bytes length and
		   is NOT a Type field."
              ::= { alcetherStatsEntry 44 }

		alcetherStatsTxExcDeferPkts		OBJECT-TYPE
              SYNTAX Counter64
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                  "The total number of frames that were deferred in excess of 6071 nibble-times
		   in 100 Mbps, 24287 bit-times in 10 Mbps mode. These frames are dropped.(This
		   stat is only in case of Half duplex and excessive defer bit reset)."
              ::= { alcetherStatsEntry 45 }

-- 10 GIG specifics parameters

         alcether10GigTable OBJECT-TYPE
              SYNTAX SEQUENCE OF Alcether10GigEntry
              MAX-ACCESS not-accessible
              STATUS current
              DESCRIPTION
                  "A list of 10 Gig specifics entries."
              ::= { physicalPort 4 }

	alcether10GigEntry OBJECT-TYPE
              SYNTAX Alcether10GigEntry
              MAX-ACCESS not-accessible
              STATUS current
              DESCRIPTION
                  "This table will be populated with the 10 gig only entries.
                  The management interface can use it to specify if A or B is the primary."
              INDEX { ifIndex }
              ::= { alcether10GigTable 1 }

          Alcether10GigEntry ::= SEQUENCE {
	      alcether10GigPrimary	    INTEGER
	      }

	  alcether10GigPrimary OBJECT-TYPE
              SYNTAX INTEGER
		{	phyAprimary(1),
	 		phyBprimary(2),
	 		notApplicable(3)
		}
              MAX-ACCESS read-write
              STATUS current
              DESCRIPTION
                  "Setting the object to 1 will make phy A as primary, 2- phy B as pirmary.
                  Value 3 should not be set. "
              ::= { alcether10GigEntry 1 }

-- End of 10 GIG specifics parameters



-- Ethernet Driver Tables *****************************

        --  EsmHybridConf table contains the configuration
        --  information about the configured inactive media for the 
        --  hybrid port only.
        --  Implementation of this group is mandantory.
        --
        --  Note that entries in this MIB Table can NOT be created by the user, only modified


        esmHybridConfTable  OBJECT-TYPE
            SYNTAX  SEQUENCE OF EsmHybridConfEntry
            MAX-ACCESS  not-accessible
            STATUS  current
            DESCRIPTION
                "A list of inactive hybrid port instances."
            ::= { physicalPort 3 }

        esmHybridConfEntry  OBJECT-TYPE
            SYNTAX  EsmHybridConfEntry
            MAX-ACCESS  not-accessible
            STATUS  current
            DESCRIPTION
                "A ESM Physical Port entry."
            INDEX { ifIndex }
            ::= { esmHybridConfTable 1 }

        EsmHybridConfEntry ::= SEQUENCE {
            esmHybridPortCfgSpeed
                INTEGER,
            esmHybridPortCfgDuplexMode
                INTEGER,
	    esmHybridPortCfgAutoNegotiation
			INTEGER,
	    esmHybridPortCfgCrossover
			INTEGER,
	    esmHybridPortCfgFlow
			INTEGER,
            esmHybridPortCfgInactiveType
			INTEGER,
	    esmHybridPortCfgSFPType
			DisplayString
            }

        esmHybridPortCfgSpeed OBJECT-TYPE
            SYNTAX INTEGER {
                speed100(1),
                speed10(2),
                speedAuto(3),
                speed1000(5),
	        speed10000(6),
	        speedMax100(8),
		speedMax1000(9)
            }
            MAX-ACCESS read-write
            STATUS current
            DESCRIPTION
            "The configured port line speed of this ESM port."
        ::= { esmHybridConfEntry 1 }

        esmHybridPortCfgDuplexMode OBJECT-TYPE
            SYNTAX INTEGER {
                fullDuplex(1),
                halfDuplex(2),
                autoDuplex(3)
            }
            MAX-ACCESS read-write
            STATUS current
            DESCRIPTION
            "The configured port duplex mode of this ESM port.
            Note: GigaEthernet support only full-duplex."
        ::= { esmHybridConfEntry 2 }

        esmHybridPortCfgAutoNegotiation   OBJECT-TYPE
            SYNTAX INTEGER {
                enable(1),
                disable(2)
            }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Allow the user to enable or disable the port auto negotiation."
	    DEFVAL { disable }
          ::= { esmHybridConfEntry 3 }

        esmHybridPortCfgCrossover   OBJECT-TYPE
            SYNTAX INTEGER {
                	mdi(1),
                	mdix(2),
			auto(3)
            }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "Allow the user to configure port crossover."
	    DEFVAL { auto }
          ::= { esmHybridConfEntry 4 }

        esmHybridPortCfgFlow   OBJECT-TYPE
            SYNTAX INTEGER {
                disable(1),
				enabledXmit(2),
                enabledRcv(3),
                enabledXmitAndRcv(4)
            }
            MAX-ACCESS  read-write
            STATUS  current
            DESCRIPTION
                 "This object is used for flow control of hybrid ports. It is similar to the dot3PauseAdminMode
		  object in dot3PauseTable. It is used to configure pause for fiber media."
	    DEFVAL { disable }
          ::= { esmHybridConfEntry 5 }

 	esmHybridPortCfgInactiveType OBJECT-TYPE
            SYNTAX INTEGER {
                fiber(1),
                copper(2)
            }
            MAX-ACCESS  read-only
            STATUS  current
            DESCRIPTION
                 "This object is only applicable to hybrid ports .
                  It indicates the configured inactive media type."
          ::= { esmHybridConfEntry 6 }

	esmHybridPortCfgSFPType OBJECT-TYPE      
            SYNTAX      DisplayString (SIZE (0..64))      
            MAX-ACCESS read-only      
            STATUS      current     
            DESCRIPTION      
                "This object is only applicable to fiber ports.      
                The string indicates the type of SFP/GBIC of active media."      
          ::= { esmHybridConfEntry 7 }    


-- End-to-End Flow Vlan Configuration *****************

	esmE2EFlowVlan OBJECT-TYPE
	    SYNTAX INTEGER (0 .. 4094)
	    MAX-ACCESS read-write
	    STATUS current
	    DESCRIPTION
		"0 - Deleting End-to-End flow control
		 1-4094 - Enable End-to-End flow control and use the Vlan configured as for End-to-End flow"
	    ::= { alcatelIND1PortMIBObjects 3 }


-- Digital Diagnostics Monitoring (DDM) **************************

ddmConfig OBJECT-TYPE
	SYNTAX		INTEGER {
					enable(1),
					disable(2)
				}
	MAX-ACCESS	read-write
	STATUS		current
	DESCRIPTION
		"This object enables/disables DDM software feature in the system."
	DEFVAL		{ disable }
	::= { ddmConfiguration 1 }

ddmTrapConfig OBJECT-TYPE
	SYNTAX		INTEGER {
					enable(1),
					disable(2)
				}
	MAX-ACCESS	read-write
	STATUS		current
	DESCRIPTION
		"This objects enables/disables traps for DDM warning/alarm threshold violations."
	DEFVAL		{ disable }
	::= { ddmConfiguration 2 }

ddmNotificationType	OBJECT-TYPE
	SYNTAX		INTEGER 
				{
					clearViolation(1),
					highAlarm(2),
					highWarning(3),
					lowWarning(4),
					lowAlarm(5)
				}
	MAX-ACCESS	accessible-for-notify
	STATUS		current
	DESCRIPTION
		"This object defines the trap type for monitored DDM parameters."
	::=	{ ddmConfiguration 3 }



-- esmViolationRecoveryTime Configuration *****************

esmViolationRecoveryTrap OBJECT-TYPE
	SYNTAX		INTEGER {
					enable(1),
					disable(2)
				}
	MAX-ACCESS	read-write
	STATUS		current
	DESCRIPTION
		"This objects enables/disables traps for user-port shutdown"
	DEFVAL		{ disable }
	::= { esmViolationRecovery 1 }


esmViolationRecoveryTime OBJECT-TYPE
	    SYNTAX INTEGER (0 .. 600)
	    MAX-ACCESS read-write
	    STATUS current
	    DESCRIPTION
		"0 - Disable the timer
		30 - 600 - timeout value to re-enable the UserPort ports"
	    ::= { esmViolationRecovery 2 }

esmViolationRecoveryNotificationType	OBJECT-TYPE
	SYNTAX		INTEGER 
				{
					clearViolation(1)
				}
	MAX-ACCESS	accessible-for-notify
	STATUS		current
	DESCRIPTION
		"This object defines the trap type for monitored violation-recovery parameters."
	::=	{ esmViolationRecovery 3 }


ddmInfoTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF DdmEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The ddmInfoTable has an entry for each SFP/XFP in the
         system that supports Digital Diagnostic Monitoring (DDM). The table is
         indexed by ifIndex. Each row in this table is dynamically added
         and removed internally by the system based on the presence or absence
         of DDM capable SFP/XFP components."
    ::= { physicalPort 5 }

ddmInfoEntry OBJECT-TYPE
    SYNTAX      DdmEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "Each row represents a particular SFP/XFP that supports Digital
         Diagnostic Monitoring.
         Entries are created and deleted internally by the system."
    INDEX { ifIndex }
    ::= { ddmInfoTable 1}

DdmEntry ::= SEQUENCE
    {
        ddmTemperature                   Integer32,
        ddmTempLowWarning                Integer32,
        ddmTempLowAlarm                  Integer32,
        ddmTempHiWarning                 Integer32,
        ddmTempHiAlarm                   Integer32,
        ddmSupplyVoltage                 Integer32,
        ddmSupplyVoltageLowWarning       Integer32,
        ddmSupplyVoltageLowAlarm         Integer32,
        ddmSupplyVoltageHiWarning        Integer32,
        ddmSupplyVoltageHiAlarm          Integer32,
        ddmTxBiasCurrent                 Integer32,
        ddmTxBiasCurrentLowWarning       Integer32,
        ddmTxBiasCurrentLowAlarm         Integer32,
        ddmTxBiasCurrentHiWarning        Integer32,
        ddmTxBiasCurrentHiAlarm          Integer32,
        ddmTxOutputPower                 Integer32,
        ddmTxOutputPowerLowWarning       Integer32,
        ddmTxOutputPowerLowAlarm         Integer32,
        ddmTxOutputPowerHiWarning        Integer32,
        ddmTxOutputPowerHiAlarm          Integer32,
        ddmRxOpticalPower                Integer32,
        ddmRxOpticalPowerLowWarning      Integer32,
        ddmRxOpticalPowerLowAlarm        Integer32,
        ddmRxOpticalPowerHiWarning       Integer32,
        ddmRxOpticalPowerHiAlarm         Integer32
    }

ddmTemperature                 OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -150000..150000)
	UNITS		"thousandth of a degree celcius"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTemperature indicates the current temperature
         of the SFP/XFP in 1000s of degrees Celsius.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 1 }

ddmTempLowWarning              OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -150000..150000)
	UNITS       "thousandth of a degree celcius"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTempLowWarning indicates the temperature
         of the SFP/XFP in 1000s of degrees Celsius that triggers a low-warning.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 2 }

ddmTempLowAlarm                OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -150000..150000)
	UNITS       "thousandth of a degree celcius"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTempLowAlarm indicates the temperature
         of the SFP/XFP in 1000s of degrees Celsius that triggers a low-alarm.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 3 }

ddmTempHiWarning               OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -150000..150000)
	UNITS       "thousandth of a degree celcius"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTempHiWarning indicates the temperature
         of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-warning.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 4 }

ddmTempHiAlarm                 OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -150000..150000)
	UNITS       "thousandth of a degree celcius"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTempHiAlarm indicates the temperature
         of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-alarm.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 5 }

ddmSupplyVoltage               OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | 0..10000)
	UNITS       "thousandth of a volt"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmSupplyVoltage indicates the current supply
         voltage of the SFP/XFP in 1000s of Volts (V).
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 6 }

ddmSupplyVoltageLowWarning     OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | 0..10000)
	UNITS       "thousandth of a volt"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmSupplyVoltageLowWarning indicates the supply
         voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-warning.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 7 }

ddmSupplyVoltageLowAlarm       OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | 0..10000)
	UNITS       "thousandth of a volt"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmSupplyVoltageLowAlarm indicates the supply
         voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-alarm.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 8 }

ddmSupplyVoltageHiWarning      OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | 0..10000)
	UNITS       "thousandth of a volt"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmSupplyVoltageHiWarning indicates the supply
         voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-warning.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 9 }

ddmSupplyVoltageHiAlarm        OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | 0..10000)
	UNITS       "thousandth of a volt"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmSupplyVoltageHiAlarm indicates the supply
         voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-alarm.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 10 }

ddmTxBiasCurrent               OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | 0..10000)
	UNITS       "thousandth of a milli-Ampere"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTxBiasCurrent indicates the current Transmit
         Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA).
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 11 }

ddmTxBiasCurrentLowWarning     OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | 0..10000)
	UNITS       "thousandth of a milli-Ampere"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTxBiasCurrentLowWarning indicates the Transmit
         Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a
         low-warning.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 12 }

ddmTxBiasCurrentLowAlarm       OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | 0..10000)
	UNITS       "thousandth of a milli-Ampere"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTxBiasCurrentLowAlarm indicates the Transmit
         Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a
         low-alarm.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 13 }

ddmTxBiasCurrentHiWarning      OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | 0..10000)
	UNITS       "thousandth of a milli-Ampere"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTxBiasCurrentHiWarning indicates the Transmit
         Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a
         hi-warning.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 14 }

ddmTxBiasCurrentHiAlarm        OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | 0..10000)
	UNITS       "thousandth of a milli-Ampere"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTxBiasCurrentHiAlarm indicates the Transmit
         Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a
         hi-alarm.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 15 }

ddmTxOutputPower               OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -40000..10000)
	UNITS       "thousandth of a dBm"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTxOutputPower indicates the current Output
         Power of the SFP/XFP in 1000s of dBm.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 16 }

ddmTxOutputPowerLowWarning     OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -40000..10000)
	UNITS       "thousandth of a dBm"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTxOutputPowerLowWarning indicates the Output Power
         of the SFP/XFP in 1000s of dBm that triggers a low-warning.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 17 }

ddmTxOutputPowerLowAlarm       OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -40000..10000)
	UNITS       "thousandth of a dBm"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTxOutputPowerLowAlarm indicates the Output Power
         of the SFP/XFP in 1000s of dBm that triggers a low-alarm.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 18 }

ddmTxOutputPowerHiWarning      OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -40000..10000)
	UNITS       "thousandth of a dBm"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTxOutputPowerHiWarning indicates the Output Power
         of the SFP/XFP in 1000s of dBm that triggers a hi-alarm.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 19 }

ddmTxOutputPowerHiAlarm        OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -40000..10000)
	UNITS       "thousandth of a dBm"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmTxOutputPowerHiAlarm indicates the Output Power
         of the SFP/XFP in 1000s of dBm that triggers a hi-alarm.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 20 }

ddmRxOpticalPower              OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -40000..10000)
	UNITS       "thousandth of a dBm"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmRxOpticalPower indicates the current Received
         Optical Power of the SFP/XFP in 1000s of dBm.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 21 }

ddmRxOpticalPowerLowWarning    OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -40000..10000)
	UNITS       "thousandth of a dBm"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmRxOpticalPowerLowWarning indicates the Received
         Optical Power of the SFP/XFP in 1000s of dBm that triggers a
         low-warning.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 22 }

ddmRxOpticalPowerLowAlarm      OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -40000..10000)
	UNITS       "thousandth of a dBm"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmRxOpticalPowerLowAlarm indicates the Received
         Optical Power of the SFP/XFP in 1000s of dBm that triggers a
         low-alarm.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 23 }

ddmRxOpticalPowerHiWarning     OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -40000..10000)
	UNITS       "thousandth of a dBm"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmRxOpticalPowerHiWarning indicates the Received
         Optical Power of the SFP/XFP in 1000s of dBm that triggers a
         hi-warning.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 24 }

ddmRxOpticalPowerHiAlarm       OBJECT-TYPE
    SYNTAX      Integer32 (-200000 | -40000..10000)
	UNITS       "thousandth of a dBm"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of ddmRxOpticalPowerHiAlarm indicates the Received
         Optical Power of the SFP/XFP in 1000s of dBm that triggers a
         hi-alarm.
		 A value of -200000 indicates this object is not applicable."
    ::= { ddmInfoEntry 25 }

-- Ethernet Driver Trap *********************

esmDrvTrapDropsLink  NOTIFICATION-TYPE
    OBJECTS    {
                  esmPortSlot,
		  esmPortIF,
                  ifInErrors,
                  ifOutErrors,
		  esmDrvTrapDrops
               }
    STATUS  current
    DESCRIPTION
           "When the Ethernet code drops the link because of
            excessive errors, a Trap is sent."
    ::= { cmmEsmDrvTraps 0 1 }

e2eStackTopoChangeTrap NOTIFICATION-TYPE
     OBJECTS    {
                   esmE2EFlowVlan
                }
     STATUS  current
     DESCRIPTION
            "Trap  Generated when  Stack Topology changes."
     ::= { cmmEsmDrvTraps 0 2 }

ddmTemperatureThresholdViolated NOTIFICATION-TYPE
	OBJECTS		{
					ifIndex,
					ddmNotificationType, 
					ddmTemperature
				}
	STATUS		current
	DESCRIPTION
		"This object notifies management station if an SFP/XFP/SFP+ temperature has crossed any 
		 threshold or reverted from previous threshold violation for a port represented by ifIndex.
		 It also provides the current realtime value of SFP/XFP/SFP+ temperature."
	::=	{ ddmNotifications 0 1 }

ddmVoltageThresholdViolated NOTIFICATION-TYPE
    OBJECTS     {
                    ifIndex,
                    ddmNotificationType,
                    ddmSupplyVoltage
                }
    STATUS      current
    DESCRIPTION
        "This object notifies management station if an SFP/XFP/SFP+ supply voltage has crossed any
         threshold or reverted from previous threshold violation for a port represented by ifIndex.
         It also provides the current realtime value of SFP/XFP/SFP+ supply voltage."
    ::= { ddmNotifications 0 2 }

ddmCurrentThresholdViolated NOTIFICATION-TYPE
    OBJECTS     {
                    ifIndex,
                    ddmNotificationType,
                    ddmTxBiasCurrent
                }
    STATUS      current
    DESCRIPTION
        "This object notifies management station if an SFP/XFP/SFP+ Tx bias current has crossed any
         threshold or reverted from previous threshold violation for a port represented by ifIndex.
         It also provides the current realtime value of SFP/XFP/SFP+ Tx bias current."
    ::= { ddmNotifications 0 3 }

ddmTxPowerThresholdViolated NOTIFICATION-TYPE
    OBJECTS     {
                    ifIndex,
                    ddmNotificationType,
                    ddmTxOutputPower
                }
    STATUS      current
    DESCRIPTION
        "This object notifies management station if an SFP/XFP/SFP+ Tx output power has crossed any
         threshold or reverted from previous threshold violation for a port represented by ifIndex.
         It also provides the current realtime value of SFP/XFP/SFP+ Tx output power."
    ::= { ddmNotifications 0 4 }


ddmRxPowerThresholdViolated NOTIFICATION-TYPE
    OBJECTS     {
                    ifIndex,
                    ddmNotificationType,
                    ddmRxOpticalPower
                }
    STATUS      current
    DESCRIPTION
        "This object notifies management station if an SFP/XFP/SFP+ Rx optical power has crossed any
         threshold or reverted from previous threshold violation for a port represented by ifIndex.
         It also provides the current realtime value of SFP/XFP/SFP+ Rx optical power."
    ::= { ddmNotifications 0 5 }


esmViolationRecoveryTimeout NOTIFICATION-TYPE
    OBJECTS     {
                    ifIndex,
                    esmViolationRecoveryNotificationType
                }
    STATUS      current
    DESCRIPTION
        "This object notifies management station if User-Port ports get re-enabled after esm violation recovery time"
    ::= { esmViolationNotifications 0 1 }

-- conformance information

alcatelIND1PortMIBCompliances OBJECT IDENTIFIER ::= { alcatelIND1PortMIBConformance 1 }
alcatelIND1PortMIBGroups      OBJECT IDENTIFIER ::= { alcatelIND1PortMIBConformance 2 }

-- compliance statements

esmConfPortCompliance MODULE-COMPLIANCE
    STATUS  current
    DESCRIPTION
            "The compliance statement for the configuration of Ethernet
            ports."
    MODULE  -- this module
        MANDATORY-GROUPS { 	esmConfMIBGroup, 
							esmDetectedConfMIBGroup, 
							esmPortModeMIBGroup,
							ddmInfoGroup,
							ddmConfigGroup,
							ddmNotificationsGroup,
							violationRecoveryGroup,
							violationNotificationsGroup
						 }
    ::= { alcatelIND1PortMIBCompliances 1 }

alcEtherStatsCompliance MODULE-COMPLIANCE
    STATUS  current
    DESCRIPTION
            "The compliance statement for the Statistics of the Ethernet
            ports."
    MODULE  -- this module
        MANDATORY-GROUPS { alcEtherStatsMIBGroup }

    ::= { alcatelIND1PortMIBCompliances 2 }

-- units of conformance



esmConfMIBGroup OBJECT-GROUP
    OBJECTS { esmPortCfgSpeed,
              esmPortCfgDuplexMode, esmPortCfgIFG,
              esmPortPauseSlotTime, esmPortMaxFloodRate,
	      esmPortFloodMcastEnable, esmPortCfgMaxFrameSize, esmPortCfgAutoNegotiation,
	      esmPortCfgCrossover, esmPortCfgFlow, esmPortFloodUnknownUcastEnable,
	      esmPortMaxUnknownUcastFloodRate,esmPortMaxMcastFloodRate,esmPortFloodBcastEnable,
	      esmPortMaxFloodRateLimit,esmPortMaxUnknownUcastFloodRateLimit,esmPortMaxMcastFloodRateLimit, esmPortCfgSFPType     	
            }
    STATUS  current
    DESCRIPTION
            "A collection of objects to support the management of global
            configuration parameters of the Ethernet ports."
    ::= { alcatelIND1PortMIBGroups 1 }

esmDetectedConfMIBGroup OBJECT-GROUP
    OBJECTS { esmPortAutoSpeed, esmPortAutoDuplexMode
            }
    STATUS  current
    DESCRIPTION
            "A collection of objects to support the Detected
            configuration parameters of the Ethernet ports."
    ::= { alcatelIND1PortMIBGroups 2 }

alcEtherStatsMIBGroup OBJECT-GROUP
    OBJECTS { alcetherClearStats, alcetherLastClearStats,
	      alcetherStatsCRCAlignErrors, alcetherStatsRxUndersizePkts,
              alcetherStatsTxUndersizePkts, alcetherStatsTxOversizePkts,
	      alcetherStatsRxJabbers, alcetherStatsRxCollisions,
	      alcetherStatsTxCollisions, alcetherStatsPkts64Octets,
              alcetherStatsPkts65to127Octets, alcetherStatsPkts128to255Octets,
              alcetherStatsPkts256to511Octets,
	      alcetherStatsPkts512to1023Octets,
	      alcetherStatsPkts1024to1518Octets,
              gigaEtherStatsPkts1519to4095Octets,
	      gigaEtherStatsPkts4096to9215Octets,
		alcetherStatsPkts1519to2047Octets,
		alcetherStatsPkts2048to4095Octets,
		alcetherStatsPkts4096Octets,
		alcetherStatsRxGiantPkts,
		alcetherStatsRxDribbleNibblePkts,
		alcetherStatsRxLongEventPkts,
		alcetherStatsRxVlanTagPkts,
		alcetherStatsRxControlPkts,
		alcetherStatsRxLenChkErrPkts,
		alcetherStatsRxCodeErrPkts,
		alcetherStatsRxDvEventPkts,
		alcetherStatsRxPrevPktDropped,
		alcetherStatsTx64Octets,
		alcetherStatsTx65to127Octets,
		alcetherStatsTx128to255Octets,
		alcetherStatsTx256to511Octets,
		alcetherStatsTx512to1023Octets,
		alcetherStatsTx1024to1518Octets,
		alcetherStatsTx1519to2047Octets,
		alcetherStatsTx2048to4095Octets,
		alcetherStatsTx4096Octets,
		alcetherStatsTxRetryCount,
		alcetherStatsTxVlanTagPkts,
		alcetherStatsTxControlPkts,
		alcetherStatsTxLatePkts,
		alcetherStatsTxTotalBytesOnWire,
		alcetherStatsTxLenChkErrPkts,
		alcetherStatsTxExcDeferPkts

            }
    STATUS  current
    DESCRIPTION
            "A collection of objects to provide all the statistics related
             to the Ethernet and GigaEthernert ports."
    ::= { alcatelIND1PortMIBGroups 3 }

alcPortNotificationGroup NOTIFICATION-GROUP
    NOTIFICATIONS {
	esmDrvTrapDropsLink
	}
    STATUS current
    DESCRIPTION
 	    "The Port MIB Notification Group."
    ::= { alcatelIND1PortMIBGroups 4 }

esmPortModeMIBGroup OBJECT-GROUP
    OBJECTS { esmPortRunningMode,
              esmPortSavedMode  
            }
    STATUS  current
    DESCRIPTION
            "A collection of objects to support the management of global
            configuration parameters of the stacking ports."
    ::= { alcatelIND1PortMIBGroups 5 }

	ddmInfoGroup	OBJECT-GROUP
	OBJECTS	{
				ddmTemperature,
        		ddmTempLowWarning,
        		ddmTempLowAlarm,
        		ddmTempHiWarning,
        		ddmTempHiAlarm,
        		ddmSupplyVoltage,
        		ddmSupplyVoltageLowWarning,
        		ddmSupplyVoltageLowAlarm,
        		ddmSupplyVoltageHiWarning,
        		ddmSupplyVoltageHiAlarm,
        		ddmTxBiasCurrent,
        		ddmTxBiasCurrentLowWarning,
        		ddmTxBiasCurrentLowAlarm,
        		ddmTxBiasCurrentHiWarning,
        		ddmTxBiasCurrentHiAlarm,
        		ddmTxOutputPower,
        		ddmTxOutputPowerLowWarning,
        		ddmTxOutputPowerLowAlarm,
        		ddmTxOutputPowerHiWarning,
        		ddmTxOutputPowerHiAlarm,
        		ddmRxOpticalPower,
        		ddmRxOpticalPowerLowWarning,
        		ddmRxOpticalPowerLowAlarm,
        		ddmRxOpticalPowerHiWarning,
        		ddmRxOpticalPowerHiAlarm
			}
	STATUS	current
	DESCRIPTION
			"A collection of objects to provide digital diagnostics information
			 related to SFPs, XFPs, and SFP+s."
	::=	{ alcatelIND1PortMIBGroups 6 }

	ddmConfigGroup	OBJECT-GROUP
	OBJECTS {
				ddmConfig,
				ddmTrapConfig			
			}
	STATUS	current
	DESCRIPTION
			"A collection of objects to allow configuration of DDM and DDM traps."
	::=	{ alcatelIND1PortMIBGroups 7 }

	ddmNotificationsGroup	NOTIFICATION-GROUP
	NOTIFICATIONS	{
						ddmTemperatureThresholdViolated,
						ddmVoltageThresholdViolated,
						ddmCurrentThresholdViolated,
						ddmTxPowerThresholdViolated,
						ddmRxPowerThresholdViolated
					}
	STATUS	current
	DESCRIPTION
			"A collection of notifications used to indicate DDM threshold violations."
	::= { alcatelIND1PortMIBGroups 8 }

	violationRecoveryGroup	OBJECT-GROUP
	OBJECTS {
				esmViolationRecoveryTrap,
				esmViolationRecoveryTime			
			}
	STATUS	current
	DESCRIPTION
			"A collection of objects to allow configuration of violationRecovery."
	::=	{ alcatelIND1PortMIBGroups 9 }

	violationNotificationsGroup NOTIFICATION-GROUP
	NOTIFICATIONS	{
						esmViolationRecoveryTimeout
			}
	STATUS	current
	DESCRIPTION
			"A collection of notifications used to indicate esm violation recovery timeout."
	::= { alcatelIND1PortMIBGroups 10 }
	END