summaryrefslogtreecommitdiff
path: root/MIBS/nokia/ALCATEL-IND1-PORT-MIB
diff options
context:
space:
mode:
authorDavid Leutgeb <david.leutgeb@mannundmouse.com>2023-12-05 12:25:34 +0100
committerDavid Leutgeb <david.leutgeb@mannundmouse.com>2023-12-05 12:25:34 +0100
commit98a672123c7872f6b9b75a9a2b6bb3aea504de6a (patch)
tree9b13bd7f563c3198047bd359195327cf28b3caf0 /MIBS/nokia/ALCATEL-IND1-PORT-MIB
downloadmibs-98a672123c7872f6b9b75a9a2b6bb3aea504de6a.tar.gz
mibs-98a672123c7872f6b9b75a9a2b6bb3aea504de6a.zip
Initial commitHEADmain
Diffstat (limited to 'MIBS/nokia/ALCATEL-IND1-PORT-MIB')
-rw-r--r--MIBS/nokia/ALCATEL-IND1-PORT-MIB2210
1 files changed, 2210 insertions, 0 deletions
diff --git a/MIBS/nokia/ALCATEL-IND1-PORT-MIB b/MIBS/nokia/ALCATEL-IND1-PORT-MIB
new file mode 100644
index 0000000..ab32af3
--- /dev/null
+++ b/MIBS/nokia/ALCATEL-IND1-PORT-MIB
@@ -0,0 +1,2210 @@
+ALCATEL-IND1-PORT-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+ OBJECT-TYPE, Counter64,
+ NOTIFICATION-TYPE, MODULE-IDENTITY,
+ TimeTicks, Integer32 FROM SNMPv2-SMI
+ MODULE-COMPLIANCE, OBJECT-GROUP,
+ NOTIFICATION-GROUP FROM SNMPv2-CONF
+ ifIndex, ifInErrors, ifOutErrors
+ FROM IF-MIB
+ softentIND1Port, cmmEsmDrvTraps
+ FROM ALCATEL-IND1-BASE
+ DisplayString FROM SNMPv2-TC;
+
+alcatelIND1PortMIB MODULE-IDENTITY
+
+ LAST-UPDATED "200704030000Z"
+ ORGANIZATION "Alcatel-Lucent"
+ CONTACT-INFO
+ "Please consult with Customer Service to ensure the most appropriate
+ version of this document is used with the products in question:
+
+ Alcatel-Lucent, Enterprise Solutions Division
+ (Formerly Alcatel Internetworking, Incorporated)
+ 26801 West Agoura Road
+ Agoura Hills, CA 91301-5122
+ United States Of America
+
+ Telephone: North America +1 800 995 2696
+ Latin America +1 877 919 9526
+ Europe +31 23 556 0100
+ Asia +65 394 7933
+ All Other +1 818 878 4507
+
+ Electronic Mail: support@ind.alcatel.com
+ World Wide Web: http://alcatel-lucent.com/wps/portal/enterprise
+ File Transfer Protocol: ftp://ftp.ind.alcatel.com/pub/products/mibs"
+
+ DESCRIPTION
+ "This module describes an authoritative enterprise-specific Simple
+ Network Management Protocol (SNMP) Management Information Base (MIB):
+
+ This group contains the configuration information data
+ for the Ethernet Switching Module.
+
+ The right to make changes in specification and other information
+ contained in this document without prior notice is reserved.
+
+ No liability shall be assumed for any incidental, indirect, special, or
+ consequential damages whatsoever arising from or related to this
+ document or the information contained herein.
+
+ Vendors, end-users, and other interested parties are granted
+ non-exclusive license to use this specification in connection with
+ management of the products for which it is intended to be used.
+
+ Copyright (C) 1995-2007 Alcatel-Lucent
+ ALL RIGHTS RESERVED WORLDWIDE"
+
+ REVISION "200704030000Z"
+ DESCRIPTION
+ "The latest version of this MIB Module."
+
+ ::= { softentIND1Port 1}
+
+alcatelIND1PortNotifications OBJECT IDENTIFIER ::= { alcatelIND1PortMIB 0 }
+alcatelIND1PortMIBObjects OBJECT IDENTIFIER ::= { alcatelIND1PortMIB 1 }
+alcatelIND1PortMIBConformance OBJECT IDENTIFIER ::= { alcatelIND1PortMIB 2 }
+
+--
+-- alcatelIND1PortMIBObjects
+--
+
+esmConfTrap OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 1 }
+physicalPort OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 2 }
+ddmConfiguration OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 4 }
+ddmNotifications OBJECT IDENTIFIER ::= { alcatelIND1PortNotifications 1 }
+esmViolationRecovery OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 5 }
+esmViolationNotifications OBJECT IDENTIFIER ::= { alcatelIND1PortNotifications 2 }
+
+-- Ethernet Driver object related to Trap *********************
+
+esmDrvTrapDrops OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION "Partitioned port (separated due to errors)."
+ ::= { esmConfTrap 1 }
+
+-- Ethernet Driver Tables *****************************
+
+ -- EsmConf group. This group contains the configuration
+ -- information data for the Ethernet Switching Module.
+ -- Implementation of this group is mandantory.
+ --
+ -- Note that this MIB can NOT be used for row creation (this
+ -- would imply that you could override the actual physical
+ -- characteristics of the physical card!).
+
+ esmConfTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF EsmConfEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A list of ESM Physical Port instances."
+ ::= { physicalPort 1 }
+
+ esmConfEntry OBJECT-TYPE
+ SYNTAX EsmConfEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A ESM Physical Port entry."
+ INDEX { ifIndex }
+ ::= { esmConfTable 1 }
+
+ EsmConfEntry ::= SEQUENCE {
+ esmPortSlot
+ Integer32,
+ esmPortIF
+ Integer32,
+ esmPortAutoSpeed
+ INTEGER,
+ esmPortAutoDuplexMode
+ INTEGER,
+ esmPortCfgSpeed
+ INTEGER,
+ esmPortCfgDuplexMode
+ INTEGER,
+ esmPortCfgIFG
+ Integer32,
+ esmPortPauseSlotTime
+ Integer32,
+ esmPortMaxFloodRate
+ INTEGER,
+ esmPortFloodMcastEnable
+ INTEGER,
+ esmPortCfgMaxFrameSize
+ Integer32,
+ esmPortCfgLongEnable
+ INTEGER,
+ esmPortCfgRuntEnable
+ INTEGER,
+ esmPortCfgRuntSize
+ Integer32,
+ esmPortCfgAutoNegotiation
+ INTEGER,
+ esmPortCfgCrossover
+ INTEGER,
+ esmPortCfgFlow
+ INTEGER,
+ esmPortCfgHybridActiveType
+ INTEGER,
+ esmPortCfgHybridMode
+ INTEGER,
+ esmPortOperationalHybridType
+ INTEGER,
+ esmPortCfgMMULowWaterMarkCellSetLimit
+ INTEGER,
+ esmPortCfgMMUDynamicCellSetLimit
+ INTEGER,
+ esmPortViolationBitMap
+ BITS,
+ esmPortViolationClearAll
+ INTEGER,
+ esmPortFloodBcastEnable
+ INTEGER,
+ esmPortFloodUnknownUcastEnable
+ INTEGER,
+ esmPortMaxUnknownUcastFloodRate
+ INTEGER,
+ esmPortMaxMcastFloodRate
+ INTEGER,
+ esmPortMaxFloodRateLimit
+ Integer32,
+ esmPortMaxUnknownUcastFloodRateLimit
+ Integer32,
+ esmPortMaxMcastFloodRateLimit
+ Integer32,
+ esmPortCfgSFPType
+ DisplayString
+ }
+
+ esmPortSlot OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The physical Slot number for this Ethernet Port.
+ Slot number has been added to be used by the private Trap."
+ ::= { esmConfEntry 1 }
+
+ esmPortIF OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The on-board interface number for this Ethernet Port.
+ Port Number has been added to be used by the private Trap."
+ ::= { esmConfEntry 2 }
+
+ esmPortAutoSpeed OBJECT-TYPE
+ SYNTAX INTEGER {
+ speed100(1),
+ speed10(2),
+ speedAuto(3),
+ unknown(4),
+ speed1000(5),
+ speed10000(6)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The automatically detected port line speed
+ of this ESM port."
+ ::= { esmConfEntry 3 }
+
+ esmPortAutoDuplexMode OBJECT-TYPE
+ SYNTAX INTEGER {
+ fullDuplex(1),
+ halfDuplex(2),
+ autoDuplex(3),
+ unknown(4)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The automatically detected port duplex mode
+ of this ESM port.
+
+ Note: GigaEthernet supports only Full duplex mode.
+ Default value for 10/100 = Half duplex mode."
+ ::= { esmConfEntry 4 }
+
+ esmPortCfgSpeed OBJECT-TYPE
+ SYNTAX INTEGER {
+ speed100(1),
+ speed10(2),
+ speedAuto(3),
+ speed1000(5),
+ speed10000(6),
+ speedMax100(8),
+ speedMax1000(9)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The configured port line speed of this ESM port."
+ ::= { esmConfEntry 5 }
+
+ esmPortCfgDuplexMode OBJECT-TYPE
+ SYNTAX INTEGER {
+ fullDuplex(1),
+ halfDuplex(2),
+ autoDuplex(3)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The configured port duplex mode of this ESM port.
+ Note: GigaEthernet support only full-duplex."
+ ::= { esmConfEntry 6 }
+
+ esmPortCfgIFG OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Contains the setting of Inter-Frame Gap (IFG), in bytes
+ for receive and transmit.
+ The range is from 9 to 12 bytes.
+
+ Note: The default value changed according to the Port type
+ Default Bandwidth value
+ 12 bytes 10Mbps 9600 nsec
+ 100Mbps 960 nsec
+ 1Gbps 96 nsec
+ 10Gbps 9.6 nsec."
+ DEFVAL { 12 }
+ ::= { esmConfEntry 7 }
+
+ esmPortPauseSlotTime OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Indicates the number of microseconds the other
+ end-station waits after the reception
+ of a pause frame.
+
+ Note: Pause Flow control is not available for 10Mbps.
+ For 100Mbps, the possible value range is
+ 5120 nanosec to 0.3 sec.
+ For 1Gbps, the possible value range is
+ 512 nanosec to 0.03 sec."
+ ::= { esmConfEntry 8 }
+
+ esmPortMaxFloodRate OBJECT-TYPE
+ SYNTAX INTEGER {
+ mbps(1),
+ percentage(2),
+ pps(3)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Broadcast flood threshold type. To set the type, set esmPortMaxFloodRateLimit also."
+ DEFVAL { mbps }
+ ::= { esmConfEntry 9 }
+
+ esmPortFloodMcastEnable OBJECT-TYPE
+ SYNTAX INTEGER {
+ disableMulticastFlood(2),
+ enableMulticastFlood(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Enable/disable the maximum flood rate
+ for multicast."
+ DEFVAL { disableMulticastFlood }
+ ::= { esmConfEntry 10 }
+
+ esmPortCfgMaxFrameSize OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Configure the value of the maximum frame
+ size allow.
+ For 10/100:
+ It is a range between 1518(untagged) and 1553 bytes.
+ For GigaEthernet:
+ It is a range between 1518 and 10240 bytes.(OS7700,OS7800,OS8800)
+ It is a range between 1518 and 9216 bytes.(OS6800)"
+ ::= { esmConfEntry 11 }
+
+ esmPortCfgLongEnable OBJECT-TYPE
+ SYNTAX INTEGER {
+ disable(0),
+ enable(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Allow the user to change the maximun Frame size.
+ Note: It is not configurable for 10/100 Ethernet port."
+ DEFVAL { disable }
+ ::= { esmConfEntry 12 }
+
+ esmPortCfgRuntEnable OBJECT-TYPE
+ SYNTAX INTEGER {
+ disable(2),
+ enable(3)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Allow the user to change the minimum Frame size."
+ DEFVAL { disable }
+ ::= { esmConfEntry 13 }
+
+ esmPortCfgRuntSize OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Configure the value of the minimum frame
+ size allow per ports.
+ The range is 0 to 64."
+ DEFVAL { 64 }
+ ::= { esmConfEntry 14 }
+
+ esmPortCfgAutoNegotiation OBJECT-TYPE
+ SYNTAX INTEGER {
+ enable(1),
+ disable(2)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Allow the user to enable or disable the port auto negotiation."
+ DEFVAL { disable }
+ ::= { esmConfEntry 15 }
+
+ esmPortCfgCrossover OBJECT-TYPE
+ SYNTAX INTEGER {
+ mdi(1),
+ mdix(2),
+ auto(3)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Allow the user to configure port crossover."
+ DEFVAL { auto }
+ ::= { esmConfEntry 16 }
+
+ esmPortCfgFlow OBJECT-TYPE
+ SYNTAX INTEGER {
+ enable(1),
+ disable(2)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Use the dot3PauseAdminMode from the standard MIB to configure the flow control."
+ DEFVAL { disable }
+ ::= { esmConfEntry 17 }
+
+ esmPortCfgHybridActiveType OBJECT-TYPE
+ SYNTAX INTEGER {
+ notapplicable(0),
+ fiber(1),
+ copper(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object is only applicable to hybrid ports .
+ It indicates configured active media type.(the operational media
+ type may be different if esmPortCfgHybridMode is configured to be
+ preferredFiber or preferredCopper)
+ For non hybrid ports notapplicable is returned as a status."
+ ::= { esmConfEntry 18 }
+
+ esmPortCfgHybridMode OBJECT-TYPE
+ SYNTAX INTEGER {
+ notapplicable(0),
+ preferredCopper(1),
+ forcedCopper(2),
+ preferredFiber(3),
+ forcedFiber(4)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object is only applicable to hybrid ports.
+ This allows the user the user to configure the media type
+ with which the port should come up.
+ The user can configure the port to come as copper only
+ or fiber only or either fiber/copper
+ (with preference to one of them)."
+ DEFVAL { preferredFiber }
+ ::= { esmConfEntry 19 }
+
+ esmPortOperationalHybridType OBJECT-TYPE
+ SYNTAX INTEGER {
+ none(0),
+ fiber(1),
+ copper(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object is only applicable to hybrid ports .
+ It indicates the actual media type that has link up and is or will be
+ passing traffic. If link is not present the object will return none(0) value."
+ ::= { esmConfEntry 20 }
+
+ esmPortCfgMMULowWaterMarkCellSetLimit OBJECT-TYPE
+ SYNTAX INTEGER (0..16383)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ " Per-port-per-CoS Head of Line blocking cell limits. Range is 0 - 16383
+ Firebolt register Offset: 0x006pp30 - 0x37
+ Bits: 13:0 CellSetLimit , Default: 0x0100
+ This setting allocates the guaranteed cells for one port's CoSx queue.
+ After cell count over this limit, it will start using dynamic cells in
+ port dynamic space."
+ DEFVAL { 256 }
+ ::= { esmConfEntry 21 }
+
+ esmPortCfgMMUDynamicCellSetLimit OBJECT-TYPE
+ SYNTAX INTEGER (0..16383)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Per-egress port cell-based dynamic (shared buffer pool) memory
+ usage drop and resume thresholds. This sets the limit for which
+ the eight CoS-Qs within a port may share once the LWMCOSCELL
+ limit is exceeded. Range is 0 - 16383
+ Firebolt register Offset: 0x006pp040
+ Bits: 13:0 Dynamic CellSetLimit ,
+ Chip Default: 0x0400 (1024).
+ The system default value for Dynamic CellSetLimit is 0x100 (256)."
+ DEFVAL { 1024 }
+ ::= { esmConfEntry 22 }
+
+
+
+ esmPortViolationBitMap OBJECT-TYPE
+ SYNTAX BITS{
+ bEniSecurityBlockPortENI(0), -- ENI App blocking this port
+ bEniSecurityBlockPortSTP(1), -- STP App blocking this port
+ bEniSecurityBlockPortSL(2), -- SL App blocking this port
+ bEniSecurityBlockPortQoS(3), -- QoS App blocking this port
+ bEniSecurityBlockPortUDLD(4), -- UDLD App blocking this port
+ bEniSecurityBlockPortETHBLK(5) -- ETHBLK App blocking this port
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION "A bit map that identifies the set of Application that have blocked
+ a port as a result of a particular violation "
+
+ ::= { esmConfEntry 23 }
+
+ esmPortViolationClearAll OBJECT-TYPE
+ SYNTAX INTEGER(0)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION "Clear all port vioaltion "
+
+ ::= { esmConfEntry 24 }
+
+
+ esmPortFloodBcastEnable OBJECT-TYPE
+ SYNTAX INTEGER {
+ disableBcastFlood(2),
+ enableBcastFlood(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Enable/disable the maximum flood rate
+ for Broadcast."
+ DEFVAL { enableBcastFlood }
+ ::= { esmConfEntry 25 }
+
+ esmPortFloodUnknownUcastEnable OBJECT-TYPE
+ SYNTAX INTEGER {
+ disableUnknownUcastFlood(2),
+ enableUnknownUcastFlood(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Enable/disable the maximum flood rate
+ for unknown unicast."
+ DEFVAL { enableUnknownUcastFlood }
+ ::= { esmConfEntry 26 }
+
+ esmPortMaxUnknownUcastFloodRate OBJECT-TYPE
+ SYNTAX INTEGER {
+ mbps(1),
+ percentage(2),
+ pps(3)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Unknown-Unicast flood threshold type. To set the type, set esmPortMaxUnknownUcastFloodRateLimit also"
+ DEFVAL { mbps }
+ ::= { esmConfEntry 27 }
+
+ esmPortMaxMcastFloodRate OBJECT-TYPE
+ SYNTAX INTEGER {
+ mbps(1),
+ percentage(2),
+ pps(3)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Multicast flood threshold type. To set the type, set esmPortMaxFloodRateLimit also."
+ DEFVAL { mbps }
+ ::= { esmConfEntry 28 }
+
+ esmPortMaxFloodRateLimit OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The value of the maximum broadcast flood limit.
+ The actual range of the flood limit depends on the port speed.
+ example:
+ Percentage: 1 - 100
+ Mbps: 1 - 1000 (1G speed)
+ PPS: 244 - 244262 (1G speed)
+ To set the limit, set esmPortMaxFloodRate first"
+ ::= { esmConfEntry 29 }
+
+
+ esmPortMaxUnknownUcastFloodRateLimit OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The value of the maximum unknown-unicast flood limit
+ The actual range of the flood limit depends on the port speed.
+ example:
+ Percentage: 1 - 100
+ Mbps: 1 - 1000 (1G speed)
+ PPS: 244 - 244262 (1G speed)
+ To set the limit, set esmPortMaxUnknownUcastFloodRate first"
+ ::= { esmConfEntry 30 }
+
+ esmPortMaxMcastFloodRateLimit OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The value of the maximum multicast flood limit
+ The actual range of the flood limit depends on the port speed.
+ example:
+ Percentage: 1 - 100
+ Mbps: 1 - 1000 (1G speed)
+ PPS: 244 - 244262 (1G speed)
+ To set the limit, set esmPortMaxMcastFloodRate first"
+ ::= { esmConfEntry 31 }
+
+ esmPortCfgSFPType OBJECT-TYPE
+ SYNTAX DisplayString (SIZE (0..64))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object is only applicable to fiber ports.
+ The string indicates the type of SFP/GBIC of active media."
+ ::= { esmConfEntry 32 }
+
+
+
+-- Ethernet Port Mode Tables *****************************
+ -- EsmPortMode group. This group contains the configuration
+ -- information data for the Ethernet Switching Module.
+ -- Implementation of this group is mandantory.
+ --
+ -- Note that this MIB can NOT be used for row creation (this
+ -- would imply that you could override the actual physical
+ -- characteristics of the physical card!).
+
+ esmPortModeTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF EsmPortModeEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A list of ESM Physical Port Mode instances."
+ ::= { physicalPort 6 }
+
+ esmPortModeEntry OBJECT-TYPE
+ SYNTAX EsmPortModeEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A ESM Physical Port Mode entry."
+ INDEX { esmPortModeIndex }
+ ::= { esmPortModeTable 1 }
+
+ EsmPortModeEntry ::= SEQUENCE {
+ esmPortModeIndex
+ INTEGER,
+ esmPortRunningMode
+ INTEGER,
+ esmPortSavedMode
+ INTEGER
+ }
+
+ esmPortModeIndex OBJECT-TYPE
+ SYNTAX INTEGER (1001..8128)
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Valid ni/port values"
+ ::= { esmPortModeEntry 1 }
+
+ esmPortRunningMode OBJECT-TYPE
+ SYNTAX INTEGER {
+ uplink(1),
+ stackable(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Currently configured Etna port 25,26 as 10G uplink user port or stacking port.
+ Default is uplink 10G port. User can not set the current mode."
+ ::= { esmPortModeEntry 2 }
+
+ esmPortSavedMode OBJECT-TYPE
+ SYNTAX INTEGER {
+ uplink(1),
+ stackable(2)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Next configured Etna port 25,26 as 10G uplink user port or stacking port.
+ At boot up, it has the same value as current esmPortRunningMode. It takes some time to
+ write to the EEPROM. Have at least more than 7 sec between each write operation"
+ ::= { esmPortModeEntry 3 }
+
+ -- The Ethernet Statistics Group
+ --
+ -- The ethernet statistics group contains statistics
+ -- measured by the probe for each monitored interface on
+ -- this device. These statistics take the form of free
+ -- running counters that start from zero when a valid entry
+ -- is created.
+ --
+ -- This group currently has statistics defined only for
+ -- Ethernet interfaces. Each alcetherStatsEntry contains
+ -- statistics for one Ethernet interface. The probe must
+ -- create one alcetherStats entry for each monitored Ethernet
+ -- interface on the device.
+
+ alcetherStatsTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF AlcetherStatsEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A list of Ethernet statistics entries."
+ ::= { physicalPort 2 }
+
+ alcetherStatsEntry OBJECT-TYPE
+ SYNTAX AlcetherStatsEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A collection of statistics kept for a particular
+ Ethernet interface. As an example, an instance of the
+ etherStatsPkts object might be named alcetherStatsPkts.1"
+ INDEX { ifIndex }
+ ::= { alcetherStatsTable 1 }
+
+ AlcetherStatsEntry ::= SEQUENCE {
+ alcetherClearStats INTEGER,
+ alcetherLastClearStats TimeTicks,
+ alcetherStatsCRCAlignErrors Counter64,
+ alcetherStatsRxUndersizePkts Counter64,
+ alcetherStatsTxUndersizePkts Counter64,
+ alcetherStatsTxOversizePkts Counter64,
+ alcetherStatsRxJabbers Counter64,
+ alcetherStatsRxCollisions Counter64,
+ alcetherStatsTxCollisions Counter64,
+ alcetherStatsPkts64Octets Counter64,
+ alcetherStatsPkts65to127Octets Counter64,
+ alcetherStatsPkts128to255Octets Counter64,
+ alcetherStatsPkts256to511Octets Counter64,
+ alcetherStatsPkts512to1023Octets Counter64,
+ alcetherStatsPkts1024to1518Octets Counter64,
+ gigaEtherStatsPkts1519to4095Octets Counter64,
+ gigaEtherStatsPkts4096to9215Octets Counter64,
+ alcetherStatsPkts1519to2047Octets Counter64,
+ alcetherStatsPkts2048to4095Octets Counter64,
+ alcetherStatsPkts4096Octets Counter64,
+ alcetherStatsRxGiantPkts Counter64,
+ alcetherStatsRxDribbleNibblePkts Counter64,
+ alcetherStatsRxLongEventPkts Counter64,
+ alcetherStatsRxVlanTagPkts Counter64,
+ alcetherStatsRxControlPkts Counter64,
+ alcetherStatsRxLenChkErrPkts Counter64,
+ alcetherStatsRxCodeErrPkts Counter64,
+ alcetherStatsRxDvEventPkts Counter64,
+ alcetherStatsRxPrevPktDropped Counter64,
+ alcetherStatsTx64Octets Counter64,
+ alcetherStatsTx65to127Octets Counter64,
+ alcetherStatsTx128to255Octets Counter64,
+ alcetherStatsTx256to511Octets Counter64,
+ alcetherStatsTx512to1023Octets Counter64,
+ alcetherStatsTx1024to1518Octets Counter64,
+ alcetherStatsTx1519to2047Octets Counter64,
+ alcetherStatsTx2048to4095Octets Counter64,
+ alcetherStatsTx4096Octets Counter64,
+ alcetherStatsTxRetryCount Counter64,
+ alcetherStatsTxVlanTagPkts Counter64,
+ alcetherStatsTxControlPkts Counter64,
+ alcetherStatsTxLatePkts Counter64,
+ alcetherStatsTxTotalBytesOnWire Counter64,
+ alcetherStatsTxLenChkErrPkts Counter64,
+ alcetherStatsTxExcDeferPkts Counter64
+ }
+
+ alcetherClearStats OBJECT-TYPE
+ SYNTAX INTEGER
+ { default(0),
+ reset(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Used to Clear all Statistics counters.
+ By default, this object contains zero value."
+ ::= { alcetherStatsEntry 1 }
+
+ alcetherLastClearStats OBJECT-TYPE
+ SYNTAX TimeTicks
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of SysUpTime at the time of all
+ the statistics counters are cleared.
+ By default, this object contains a zero value."
+ ::= { alcetherStatsEntry 2 }
+
+ alcetherStatsCRCAlignErrors OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of packets received that
+ had a length (excluding framing bits, but
+ including FCS octets) of between 64 and 1518
+ octets, inclusive, but but had either a bad
+ Frame Check Sequence (FCS) with an integral
+ number of octets (FCS Error) or a bad FCS with
+ a non-integral number of octets (Alignment Error)."
+ ::= { alcetherStatsEntry 3 }
+
+ alcetherStatsRxUndersizePkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of packets received that were
+ less than 64 octets long (excluding framing bits,
+ but including FCS octets) and were otherwise well
+ formed."
+ ::= { alcetherStatsEntry 4 }
+
+ alcetherStatsTxUndersizePkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of packets transmitted that were
+ less than 64 octets long (excluding framing bits,
+ but including FCS octets) and were otherwise well
+ formed."
+ ::= { alcetherStatsEntry 5 }
+
+ alcetherStatsTxOversizePkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of packets transmitted that were
+ longer than 1518 octets long (excluding framing bits,
+ but including FCS octets) and were otherwise well
+ formed."
+ ::= { alcetherStatsEntry 6 }
+
+ alcetherStatsRxJabbers OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of packets received that were
+ longer than 1518 octets (excluding framing bits,
+ but including FCS octets), and had either a bad
+ Frame Check Sequence (FCS) with an integral number
+ of octets (FCS Error) or a bad FCS with a
+ non-integral number of octets (Alignment Error).
+
+ Note that this definition of jabber is different
+ than the definition in IEEE-802.3 section 8.2.1.5
+ (10BASE5) and section 10.3.1.4 (10BASE2). These
+ documents define jabber as the condition where any
+ packet exceeds 20 ms. The allowed range to detect
+ jabber is between 20 ms and 150 ms."
+ ::= { alcetherStatsEntry 7 }
+
+ alcetherStatsRxCollisions OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The best estimate of the total number of collisions
+ on this Ethernet segment (in reception).
+ Only for Ethernet Interfaces.
+
+ The value returned will depend on the location of
+ the RMON probe. Section 8.2.1.3 (10BASE-5) and
+ section 10.3.1.3 (10BASE-2) of IEEE standard 802.3
+ states that a station must detect a collision, in
+ the receive mode, if three or more stations are
+ transmitting simultaneously. A repeater port must
+ detect a collision when two or more stations are
+ transmitting simultaneously. Thus a probe placed on
+ a repeater port could record more collisions than a
+ probe connected to a station on the same segment
+ would.
+
+ Probe location plays a much smaller role when
+ considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE
+ standard 802.3 defines a collision as the
+ simultaneous presence of signals on the DO and RD
+ circuits (transmitting and receiving at the same
+ time). A 10BASE-T station can only detect
+ collisions when it is transmitting. Thus probes
+ placed on a station and a repeater, should report
+ the same number of collisions.
+
+ Note also that an RMON probe inside a repeater
+ should ideally report collisions between the
+ repeater and one or more other hosts (transmit
+ collisions as defined by IEEE 802.3k) plus receiver
+ collisions observed on any coax segments to which
+ the repeater is connected."
+ ::= { alcetherStatsEntry 8 }
+
+ alcetherStatsTxCollisions OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The best estimate of the total number of collisions
+ on this Ethernet segment (in transmition).
+ Only for Ethernet Interfaces.
+
+ The value returned will depend on the location of
+ the RMON probe. Section 8.2.1.3 (10BASE-5) and
+ section 10.3.1.3 (10BASE-2) of IEEE standard 802.3
+ states that a station must detect a collision, in
+ the receive mode, if three or more stations are
+ transmitting simultaneously. A repeater port must
+ detect a collision when two or more stations are
+ transmitting simultaneously. Thus a probe placed on
+ a repeater port could record more collisions than a
+ probe connected to a station on the same segment
+ would.
+
+ Probe location plays a much smaller role when
+ considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE
+ standard 802.3 defines a collision as the
+ simultaneous presence of signals on the DO and RD
+ circuits (transmitting and receiving at the same
+ time). A 10BASE-T station can only detect
+ collisions when it is transmitting. Thus probes
+ placed on a station and a repeater, should report
+ the same number of collisions.
+
+ Note also that an RMON probe inside a repeater
+ should ideally report collisions between the
+ repeater and one or more other hosts (transmit
+ collisions as defined by IEEE 802.3k) plus receiver
+ collisions observed on any coax segments to which
+ the repeater is connected."
+ ::= { alcetherStatsEntry 9 }
+
+ alcetherStatsPkts64Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of packets (including bad
+ packets) received that were 64 octets in length
+ (excluding framing bits but including FCS octets)."
+ ::= { alcetherStatsEntry 10 }
+
+ alcetherStatsPkts65to127Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of packets (including bad
+ packets) received that were between
+ 65 and 127 octets in length inclusive
+ (excluding framing bits but including FCS octets)."
+ ::= { alcetherStatsEntry 11 }
+
+ alcetherStatsPkts128to255Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of packets (including bad
+ packets) received that were between
+ 128 and 255 octets in length inclusive
+ (excluding framing bits but including FCS octets)."
+ ::= { alcetherStatsEntry 12 }
+
+ alcetherStatsPkts256to511Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of packets (including bad
+ packets) received that were between
+ 256 and 511 octets in length inclusive
+ (excluding framing bits but including FCS octets)."
+ ::= { alcetherStatsEntry 13 }
+
+ alcetherStatsPkts512to1023Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of packets (including bad
+ packets) received that were between
+ 512 and 1023 octets in length inclusive
+ (excluding framing bits but including FCS octets)."
+ ::= { alcetherStatsEntry 14 }
+
+ alcetherStatsPkts1024to1518Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of packets (including bad
+ packets) received that were between
+ 1024 and 1518 octets in length inclusive
+ (excluding framing bits but including FCS octets).
+ For both Ethernet and GigaEthernet."
+ ::= { alcetherStatsEntry 15 }
+
+ gigaEtherStatsPkts1519to4095Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of packets (including bad
+ packets) received that were between
+ 1519 and 4095 octets in length inclusive
+ (excluding framing bits but including FCS octets).
+ Only for GigaEthernet interfaces"
+ ::= { alcetherStatsEntry 16 }
+
+ gigaEtherStatsPkts4096to9215Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of packets (including bad
+ packets) received that were between
+ 4096 and 9215 octets in length inclusive
+ (excluding framing bits but including FCS octets).
+ Only for GigaEthernet interfaces"
+ ::= { alcetherStatsEntry 17 }
+
+
+ alcetherStatsPkts1519to2047Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of frames(including error packets) received
+ that were between 1519 and 2047 bytes in length inclusive
+ (excluding framing bits but including FCS bytes).
+ "
+ ::= { alcetherStatsEntry 18 }
+
+ alcetherStatsPkts2048to4095Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of frames(including error packets) received
+ that were between 2048 and 4095 bytes in length inclusive
+ (excluding framing bits but including FCS bytes).
+ "
+ ::= { alcetherStatsEntry 19 }
+
+ alcetherStatsPkts4096Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of frames(including error packets) received
+ that were greater than or equal to 4096 bytes in length inclusive
+ (excluding framing bits but including FCS bytes).
+ "
+ ::= { alcetherStatsEntry 20 }
+
+ alcetherStatsRxGiantPkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of frames that are greater than the specified
+ Max length value, with a valid CRC, dropped because too long.
+ "
+ ::= { alcetherStatsEntry 21 }
+
+ alcetherStatsRxDribbleNibblePkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of frames for which a dribble nibble has been
+ received and CRC is correct.
+ "
+ ::= { alcetherStatsEntry 22 }
+
+ alcetherStatsRxLongEventPkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of frames for which the Carrier sense exceeds
+ 50000 bit times for 10 Mbits/sec or 80000 bit times for
+ 100 Mbits/sec."
+ ::= { alcetherStatsEntry 23 }
+
+ alcetherStatsRxVlanTagPkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of frames for which Type/Length field
+ contains the VLAN protocol identifier (0x8100). "
+ ::= { alcetherStatsEntry 24 }
+
+ alcetherStatsRxControlPkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of frames that were recognized as control frames."
+ ::= { alcetherStatsEntry 25 }
+
+ alcetherStatsRxLenChkErrPkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of frames for which the frame length field value
+ in the Type/Length field does not match the actual data bytes
+ length and is NOT a type field."
+ ::= { alcetherStatsEntry 26 }
+
+ alcetherStatsRxCodeErrPkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of frames for which one or more nibbles were
+ signaled as errors during reception of the frame."
+ ::= { alcetherStatsEntry 27 }
+
+ alcetherStatsRxDvEventPkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of frames for which a RX_DV event (packet not
+ too long enough to be valid packet) has been seen before the
+ correct frame."
+ ::= { alcetherStatsEntry 28 }
+
+ alcetherStatsRxPrevPktDropped OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of frames for which a packet has been dropped
+ (because of too small IFG) before the correct frame."
+ ::= { alcetherStatsEntry 29 }
+
+ alcetherStatsTx64Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of transmitted frames of 64 bytes."
+ ::= { alcetherStatsEntry 30 }
+
+ alcetherStatsTx65to127Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of transmitted frames that were between
+ 65 and 127 bytes in length inclusive (excluding framing bits
+ but including FCS bytes)."
+ ::= { alcetherStatsEntry 31 }
+
+ alcetherStatsTx128to255Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of transmitted frames that were between
+ 128 and 255 bytes in length inclusive (excluding framing bits
+ but including FCS bytes)."
+ ::= { alcetherStatsEntry 32 }
+
+ alcetherStatsTx256to511Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of transmitted frames that were between
+ 256 and 511 bytes in length inclusive (excluding framing bits
+ but including FCS bytes)."
+ ::= { alcetherStatsEntry 33 }
+
+ alcetherStatsTx512to1023Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of transmitted frames that were between
+ 512 and 1023 bytes in length inclusive (excluding framing bits
+ but including FCS bytes)."
+ ::= { alcetherStatsEntry 34 }
+
+ alcetherStatsTx1024to1518Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of transmitted frames that were between
+ 1024 and 1518 bytes in length inclusive (excluding framing bits
+ but including FCS bytes)."
+ ::= { alcetherStatsEntry 35 }
+
+ alcetherStatsTx1519to2047Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of transmitted frames that were between
+ 1519 and 2047 bytes in length inclusive (excluding framing bits
+ but including FCS bytes)."
+ ::= { alcetherStatsEntry 36 }
+
+ alcetherStatsTx2048to4095Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of transmitted frames that were between
+ 2048 and 4095 bytes in length inclusive (excluding framing bits
+ but including FCS bytes)."
+ ::= { alcetherStatsEntry 37 }
+
+ alcetherStatsTx4096Octets OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of transmitted frames that were greater than
+ or equal to 4096 bytes in length and less than Max frame length
+ (excluding framing bits but including FCS bytes)."
+ ::= { alcetherStatsEntry 38 }
+
+ alcetherStatsTxRetryCount OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of collisions that the frames faced during
+ transmission attempts."
+ ::= { alcetherStatsEntry 39 }
+
+ alcetherStatsTxVlanTagPkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of transmitted frames for which Type/Length field contains the
+ VLAN protocol identifier (0x8100)."
+ ::= { alcetherStatsEntry 40 }
+
+ alcetherStatsTxControlPkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of transmitted frames that were recognised as control frames."
+ ::= { alcetherStatsEntry 41 }
+
+ alcetherStatsTxLatePkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of late collisions that occured beyond the collision window."
+ ::= { alcetherStatsEntry 42 }
+
+ alcetherStatsTxTotalBytesOnWire OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of bytes transmitted on wire, including all bytes from collided
+ attempts."
+ ::= { alcetherStatsEntry 43 }
+
+ alcetherStatsTxLenChkErrPkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of transmitted frames for which the frame length field value
+ in the Type/Length field does not match the actual data bytes length and
+ is NOT a Type field."
+ ::= { alcetherStatsEntry 44 }
+
+ alcetherStatsTxExcDeferPkts OBJECT-TYPE
+ SYNTAX Counter64
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The total number of frames that were deferred in excess of 6071 nibble-times
+ in 100 Mbps, 24287 bit-times in 10 Mbps mode. These frames are dropped.(This
+ stat is only in case of Half duplex and excessive defer bit reset)."
+ ::= { alcetherStatsEntry 45 }
+
+-- 10 GIG specifics parameters
+
+ alcether10GigTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Alcether10GigEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A list of 10 Gig specifics entries."
+ ::= { physicalPort 4 }
+
+ alcether10GigEntry OBJECT-TYPE
+ SYNTAX Alcether10GigEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table will be populated with the 10 gig only entries.
+ The management interface can use it to specify if A or B is the primary."
+ INDEX { ifIndex }
+ ::= { alcether10GigTable 1 }
+
+ Alcether10GigEntry ::= SEQUENCE {
+ alcether10GigPrimary INTEGER
+ }
+
+ alcether10GigPrimary OBJECT-TYPE
+ SYNTAX INTEGER
+ { phyAprimary(1),
+ phyBprimary(2),
+ notApplicable(3)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Setting the object to 1 will make phy A as primary, 2- phy B as pirmary.
+ Value 3 should not be set. "
+ ::= { alcether10GigEntry 1 }
+
+-- End of 10 GIG specifics parameters
+
+
+
+-- Ethernet Driver Tables *****************************
+
+ -- EsmHybridConf table contains the configuration
+ -- information about the configured inactive media for the
+ -- hybrid port only.
+ -- Implementation of this group is mandantory.
+ --
+ -- Note that entries in this MIB Table can NOT be created by the user, only modified
+
+
+ esmHybridConfTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF EsmHybridConfEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A list of inactive hybrid port instances."
+ ::= { physicalPort 3 }
+
+ esmHybridConfEntry OBJECT-TYPE
+ SYNTAX EsmHybridConfEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A ESM Physical Port entry."
+ INDEX { ifIndex }
+ ::= { esmHybridConfTable 1 }
+
+ EsmHybridConfEntry ::= SEQUENCE {
+ esmHybridPortCfgSpeed
+ INTEGER,
+ esmHybridPortCfgDuplexMode
+ INTEGER,
+ esmHybridPortCfgAutoNegotiation
+ INTEGER,
+ esmHybridPortCfgCrossover
+ INTEGER,
+ esmHybridPortCfgFlow
+ INTEGER,
+ esmHybridPortCfgInactiveType
+ INTEGER,
+ esmHybridPortCfgSFPType
+ DisplayString
+ }
+
+ esmHybridPortCfgSpeed OBJECT-TYPE
+ SYNTAX INTEGER {
+ speed100(1),
+ speed10(2),
+ speedAuto(3),
+ speed1000(5),
+ speed10000(6),
+ speedMax100(8),
+ speedMax1000(9)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The configured port line speed of this ESM port."
+ ::= { esmHybridConfEntry 1 }
+
+ esmHybridPortCfgDuplexMode OBJECT-TYPE
+ SYNTAX INTEGER {
+ fullDuplex(1),
+ halfDuplex(2),
+ autoDuplex(3)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The configured port duplex mode of this ESM port.
+ Note: GigaEthernet support only full-duplex."
+ ::= { esmHybridConfEntry 2 }
+
+ esmHybridPortCfgAutoNegotiation OBJECT-TYPE
+ SYNTAX INTEGER {
+ enable(1),
+ disable(2)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Allow the user to enable or disable the port auto negotiation."
+ DEFVAL { disable }
+ ::= { esmHybridConfEntry 3 }
+
+ esmHybridPortCfgCrossover OBJECT-TYPE
+ SYNTAX INTEGER {
+ mdi(1),
+ mdix(2),
+ auto(3)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Allow the user to configure port crossover."
+ DEFVAL { auto }
+ ::= { esmHybridConfEntry 4 }
+
+ esmHybridPortCfgFlow OBJECT-TYPE
+ SYNTAX INTEGER {
+ disable(1),
+ enabledXmit(2),
+ enabledRcv(3),
+ enabledXmitAndRcv(4)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object is used for flow control of hybrid ports. It is similar to the dot3PauseAdminMode
+ object in dot3PauseTable. It is used to configure pause for fiber media."
+ DEFVAL { disable }
+ ::= { esmHybridConfEntry 5 }
+
+ esmHybridPortCfgInactiveType OBJECT-TYPE
+ SYNTAX INTEGER {
+ fiber(1),
+ copper(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object is only applicable to hybrid ports .
+ It indicates the configured inactive media type."
+ ::= { esmHybridConfEntry 6 }
+
+ esmHybridPortCfgSFPType OBJECT-TYPE
+ SYNTAX DisplayString (SIZE (0..64))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object is only applicable to fiber ports.
+ The string indicates the type of SFP/GBIC of active media."
+ ::= { esmHybridConfEntry 7 }
+
+
+-- End-to-End Flow Vlan Configuration *****************
+
+ esmE2EFlowVlan OBJECT-TYPE
+ SYNTAX INTEGER (0 .. 4094)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "0 - Deleting End-to-End flow control
+ 1-4094 - Enable End-to-End flow control and use the Vlan configured as for End-to-End flow"
+ ::= { alcatelIND1PortMIBObjects 3 }
+
+
+-- Digital Diagnostics Monitoring (DDM) **************************
+
+ddmConfig OBJECT-TYPE
+ SYNTAX INTEGER {
+ enable(1),
+ disable(2)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object enables/disables DDM software feature in the system."
+ DEFVAL { disable }
+ ::= { ddmConfiguration 1 }
+
+ddmTrapConfig OBJECT-TYPE
+ SYNTAX INTEGER {
+ enable(1),
+ disable(2)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This objects enables/disables traps for DDM warning/alarm threshold violations."
+ DEFVAL { disable }
+ ::= { ddmConfiguration 2 }
+
+ddmNotificationType OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ clearViolation(1),
+ highAlarm(2),
+ highWarning(3),
+ lowWarning(4),
+ lowAlarm(5)
+ }
+ MAX-ACCESS accessible-for-notify
+ STATUS current
+ DESCRIPTION
+ "This object defines the trap type for monitored DDM parameters."
+ ::= { ddmConfiguration 3 }
+
+
+
+-- esmViolationRecoveryTime Configuration *****************
+
+esmViolationRecoveryTrap OBJECT-TYPE
+ SYNTAX INTEGER {
+ enable(1),
+ disable(2)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This objects enables/disables traps for user-port shutdown"
+ DEFVAL { disable }
+ ::= { esmViolationRecovery 1 }
+
+
+esmViolationRecoveryTime OBJECT-TYPE
+ SYNTAX INTEGER (0 .. 600)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "0 - Disable the timer
+ 30 - 600 - timeout value to re-enable the UserPort ports"
+ ::= { esmViolationRecovery 2 }
+
+esmViolationRecoveryNotificationType OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ clearViolation(1)
+ }
+ MAX-ACCESS accessible-for-notify
+ STATUS current
+ DESCRIPTION
+ "This object defines the trap type for monitored violation-recovery parameters."
+ ::= { esmViolationRecovery 3 }
+
+
+ddmInfoTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF DdmEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "The ddmInfoTable has an entry for each SFP/XFP in the
+ system that supports Digital Diagnostic Monitoring (DDM). The table is
+ indexed by ifIndex. Each row in this table is dynamically added
+ and removed internally by the system based on the presence or absence
+ of DDM capable SFP/XFP components."
+ ::= { physicalPort 5 }
+
+ddmInfoEntry OBJECT-TYPE
+ SYNTAX DdmEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each row represents a particular SFP/XFP that supports Digital
+ Diagnostic Monitoring.
+ Entries are created and deleted internally by the system."
+ INDEX { ifIndex }
+ ::= { ddmInfoTable 1}
+
+DdmEntry ::= SEQUENCE
+ {
+ ddmTemperature Integer32,
+ ddmTempLowWarning Integer32,
+ ddmTempLowAlarm Integer32,
+ ddmTempHiWarning Integer32,
+ ddmTempHiAlarm Integer32,
+ ddmSupplyVoltage Integer32,
+ ddmSupplyVoltageLowWarning Integer32,
+ ddmSupplyVoltageLowAlarm Integer32,
+ ddmSupplyVoltageHiWarning Integer32,
+ ddmSupplyVoltageHiAlarm Integer32,
+ ddmTxBiasCurrent Integer32,
+ ddmTxBiasCurrentLowWarning Integer32,
+ ddmTxBiasCurrentLowAlarm Integer32,
+ ddmTxBiasCurrentHiWarning Integer32,
+ ddmTxBiasCurrentHiAlarm Integer32,
+ ddmTxOutputPower Integer32,
+ ddmTxOutputPowerLowWarning Integer32,
+ ddmTxOutputPowerLowAlarm Integer32,
+ ddmTxOutputPowerHiWarning Integer32,
+ ddmTxOutputPowerHiAlarm Integer32,
+ ddmRxOpticalPower Integer32,
+ ddmRxOpticalPowerLowWarning Integer32,
+ ddmRxOpticalPowerLowAlarm Integer32,
+ ddmRxOpticalPowerHiWarning Integer32,
+ ddmRxOpticalPowerHiAlarm Integer32
+ }
+
+ddmTemperature OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -150000..150000)
+ UNITS "thousandth of a degree celcius"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTemperature indicates the current temperature
+ of the SFP/XFP in 1000s of degrees Celsius.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 1 }
+
+ddmTempLowWarning OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -150000..150000)
+ UNITS "thousandth of a degree celcius"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTempLowWarning indicates the temperature
+ of the SFP/XFP in 1000s of degrees Celsius that triggers a low-warning.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 2 }
+
+ddmTempLowAlarm OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -150000..150000)
+ UNITS "thousandth of a degree celcius"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTempLowAlarm indicates the temperature
+ of the SFP/XFP in 1000s of degrees Celsius that triggers a low-alarm.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 3 }
+
+ddmTempHiWarning OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -150000..150000)
+ UNITS "thousandth of a degree celcius"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTempHiWarning indicates the temperature
+ of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-warning.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 4 }
+
+ddmTempHiAlarm OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -150000..150000)
+ UNITS "thousandth of a degree celcius"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTempHiAlarm indicates the temperature
+ of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-alarm.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 5 }
+
+ddmSupplyVoltage OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | 0..10000)
+ UNITS "thousandth of a volt"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmSupplyVoltage indicates the current supply
+ voltage of the SFP/XFP in 1000s of Volts (V).
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 6 }
+
+ddmSupplyVoltageLowWarning OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | 0..10000)
+ UNITS "thousandth of a volt"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmSupplyVoltageLowWarning indicates the supply
+ voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-warning.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 7 }
+
+ddmSupplyVoltageLowAlarm OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | 0..10000)
+ UNITS "thousandth of a volt"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmSupplyVoltageLowAlarm indicates the supply
+ voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-alarm.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 8 }
+
+ddmSupplyVoltageHiWarning OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | 0..10000)
+ UNITS "thousandth of a volt"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmSupplyVoltageHiWarning indicates the supply
+ voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-warning.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 9 }
+
+ddmSupplyVoltageHiAlarm OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | 0..10000)
+ UNITS "thousandth of a volt"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmSupplyVoltageHiAlarm indicates the supply
+ voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-alarm.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 10 }
+
+ddmTxBiasCurrent OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | 0..10000)
+ UNITS "thousandth of a milli-Ampere"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTxBiasCurrent indicates the current Transmit
+ Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA).
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 11 }
+
+ddmTxBiasCurrentLowWarning OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | 0..10000)
+ UNITS "thousandth of a milli-Ampere"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTxBiasCurrentLowWarning indicates the Transmit
+ Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a
+ low-warning.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 12 }
+
+ddmTxBiasCurrentLowAlarm OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | 0..10000)
+ UNITS "thousandth of a milli-Ampere"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTxBiasCurrentLowAlarm indicates the Transmit
+ Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a
+ low-alarm.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 13 }
+
+ddmTxBiasCurrentHiWarning OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | 0..10000)
+ UNITS "thousandth of a milli-Ampere"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTxBiasCurrentHiWarning indicates the Transmit
+ Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a
+ hi-warning.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 14 }
+
+ddmTxBiasCurrentHiAlarm OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | 0..10000)
+ UNITS "thousandth of a milli-Ampere"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTxBiasCurrentHiAlarm indicates the Transmit
+ Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a
+ hi-alarm.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 15 }
+
+ddmTxOutputPower OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -40000..10000)
+ UNITS "thousandth of a dBm"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTxOutputPower indicates the current Output
+ Power of the SFP/XFP in 1000s of dBm.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 16 }
+
+ddmTxOutputPowerLowWarning OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -40000..10000)
+ UNITS "thousandth of a dBm"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTxOutputPowerLowWarning indicates the Output Power
+ of the SFP/XFP in 1000s of dBm that triggers a low-warning.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 17 }
+
+ddmTxOutputPowerLowAlarm OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -40000..10000)
+ UNITS "thousandth of a dBm"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTxOutputPowerLowAlarm indicates the Output Power
+ of the SFP/XFP in 1000s of dBm that triggers a low-alarm.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 18 }
+
+ddmTxOutputPowerHiWarning OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -40000..10000)
+ UNITS "thousandth of a dBm"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTxOutputPowerHiWarning indicates the Output Power
+ of the SFP/XFP in 1000s of dBm that triggers a hi-alarm.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 19 }
+
+ddmTxOutputPowerHiAlarm OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -40000..10000)
+ UNITS "thousandth of a dBm"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmTxOutputPowerHiAlarm indicates the Output Power
+ of the SFP/XFP in 1000s of dBm that triggers a hi-alarm.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 20 }
+
+ddmRxOpticalPower OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -40000..10000)
+ UNITS "thousandth of a dBm"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmRxOpticalPower indicates the current Received
+ Optical Power of the SFP/XFP in 1000s of dBm.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 21 }
+
+ddmRxOpticalPowerLowWarning OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -40000..10000)
+ UNITS "thousandth of a dBm"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmRxOpticalPowerLowWarning indicates the Received
+ Optical Power of the SFP/XFP in 1000s of dBm that triggers a
+ low-warning.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 22 }
+
+ddmRxOpticalPowerLowAlarm OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -40000..10000)
+ UNITS "thousandth of a dBm"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmRxOpticalPowerLowAlarm indicates the Received
+ Optical Power of the SFP/XFP in 1000s of dBm that triggers a
+ low-alarm.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 23 }
+
+ddmRxOpticalPowerHiWarning OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -40000..10000)
+ UNITS "thousandth of a dBm"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmRxOpticalPowerHiWarning indicates the Received
+ Optical Power of the SFP/XFP in 1000s of dBm that triggers a
+ hi-warning.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 24 }
+
+ddmRxOpticalPowerHiAlarm OBJECT-TYPE
+ SYNTAX Integer32 (-200000 | -40000..10000)
+ UNITS "thousandth of a dBm"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The value of ddmRxOpticalPowerHiAlarm indicates the Received
+ Optical Power of the SFP/XFP in 1000s of dBm that triggers a
+ hi-alarm.
+ A value of -200000 indicates this object is not applicable."
+ ::= { ddmInfoEntry 25 }
+
+-- Ethernet Driver Trap *********************
+
+esmDrvTrapDropsLink NOTIFICATION-TYPE
+ OBJECTS {
+ esmPortSlot,
+ esmPortIF,
+ ifInErrors,
+ ifOutErrors,
+ esmDrvTrapDrops
+ }
+ STATUS current
+ DESCRIPTION
+ "When the Ethernet code drops the link because of
+ excessive errors, a Trap is sent."
+ ::= { cmmEsmDrvTraps 0 1 }
+
+e2eStackTopoChangeTrap NOTIFICATION-TYPE
+ OBJECTS {
+ esmE2EFlowVlan
+ }
+ STATUS current
+ DESCRIPTION
+ "Trap Generated when Stack Topology changes."
+ ::= { cmmEsmDrvTraps 0 2 }
+
+ddmTemperatureThresholdViolated NOTIFICATION-TYPE
+ OBJECTS {
+ ifIndex,
+ ddmNotificationType,
+ ddmTemperature
+ }
+ STATUS current
+ DESCRIPTION
+ "This object notifies management station if an SFP/XFP/SFP+ temperature has crossed any
+ threshold or reverted from previous threshold violation for a port represented by ifIndex.
+ It also provides the current realtime value of SFP/XFP/SFP+ temperature."
+ ::= { ddmNotifications 0 1 }
+
+ddmVoltageThresholdViolated NOTIFICATION-TYPE
+ OBJECTS {
+ ifIndex,
+ ddmNotificationType,
+ ddmSupplyVoltage
+ }
+ STATUS current
+ DESCRIPTION
+ "This object notifies management station if an SFP/XFP/SFP+ supply voltage has crossed any
+ threshold or reverted from previous threshold violation for a port represented by ifIndex.
+ It also provides the current realtime value of SFP/XFP/SFP+ supply voltage."
+ ::= { ddmNotifications 0 2 }
+
+ddmCurrentThresholdViolated NOTIFICATION-TYPE
+ OBJECTS {
+ ifIndex,
+ ddmNotificationType,
+ ddmTxBiasCurrent
+ }
+ STATUS current
+ DESCRIPTION
+ "This object notifies management station if an SFP/XFP/SFP+ Tx bias current has crossed any
+ threshold or reverted from previous threshold violation for a port represented by ifIndex.
+ It also provides the current realtime value of SFP/XFP/SFP+ Tx bias current."
+ ::= { ddmNotifications 0 3 }
+
+ddmTxPowerThresholdViolated NOTIFICATION-TYPE
+ OBJECTS {
+ ifIndex,
+ ddmNotificationType,
+ ddmTxOutputPower
+ }
+ STATUS current
+ DESCRIPTION
+ "This object notifies management station if an SFP/XFP/SFP+ Tx output power has crossed any
+ threshold or reverted from previous threshold violation for a port represented by ifIndex.
+ It also provides the current realtime value of SFP/XFP/SFP+ Tx output power."
+ ::= { ddmNotifications 0 4 }
+
+
+ddmRxPowerThresholdViolated NOTIFICATION-TYPE
+ OBJECTS {
+ ifIndex,
+ ddmNotificationType,
+ ddmRxOpticalPower
+ }
+ STATUS current
+ DESCRIPTION
+ "This object notifies management station if an SFP/XFP/SFP+ Rx optical power has crossed any
+ threshold or reverted from previous threshold violation for a port represented by ifIndex.
+ It also provides the current realtime value of SFP/XFP/SFP+ Rx optical power."
+ ::= { ddmNotifications 0 5 }
+
+
+esmViolationRecoveryTimeout NOTIFICATION-TYPE
+ OBJECTS {
+ ifIndex,
+ esmViolationRecoveryNotificationType
+ }
+ STATUS current
+ DESCRIPTION
+ "This object notifies management station if User-Port ports get re-enabled after esm violation recovery time"
+ ::= { esmViolationNotifications 0 1 }
+
+-- conformance information
+
+alcatelIND1PortMIBCompliances OBJECT IDENTIFIER ::= { alcatelIND1PortMIBConformance 1 }
+alcatelIND1PortMIBGroups OBJECT IDENTIFIER ::= { alcatelIND1PortMIBConformance 2 }
+
+-- compliance statements
+
+esmConfPortCompliance MODULE-COMPLIANCE
+ STATUS current
+ DESCRIPTION
+ "The compliance statement for the configuration of Ethernet
+ ports."
+ MODULE -- this module
+ MANDATORY-GROUPS { esmConfMIBGroup,
+ esmDetectedConfMIBGroup,
+ esmPortModeMIBGroup,
+ ddmInfoGroup,
+ ddmConfigGroup,
+ ddmNotificationsGroup,
+ violationRecoveryGroup,
+ violationNotificationsGroup
+ }
+ ::= { alcatelIND1PortMIBCompliances 1 }
+
+alcEtherStatsCompliance MODULE-COMPLIANCE
+ STATUS current
+ DESCRIPTION
+ "The compliance statement for the Statistics of the Ethernet
+ ports."
+ MODULE -- this module
+ MANDATORY-GROUPS { alcEtherStatsMIBGroup }
+
+ ::= { alcatelIND1PortMIBCompliances 2 }
+
+-- units of conformance
+
+
+
+esmConfMIBGroup OBJECT-GROUP
+ OBJECTS { esmPortCfgSpeed,
+ esmPortCfgDuplexMode, esmPortCfgIFG,
+ esmPortPauseSlotTime, esmPortMaxFloodRate,
+ esmPortFloodMcastEnable, esmPortCfgMaxFrameSize, esmPortCfgAutoNegotiation,
+ esmPortCfgCrossover, esmPortCfgFlow, esmPortFloodUnknownUcastEnable,
+ esmPortMaxUnknownUcastFloodRate,esmPortMaxMcastFloodRate,esmPortFloodBcastEnable,
+ esmPortMaxFloodRateLimit,esmPortMaxUnknownUcastFloodRateLimit,esmPortMaxMcastFloodRateLimit, esmPortCfgSFPType
+ }
+ STATUS current
+ DESCRIPTION
+ "A collection of objects to support the management of global
+ configuration parameters of the Ethernet ports."
+ ::= { alcatelIND1PortMIBGroups 1 }
+
+esmDetectedConfMIBGroup OBJECT-GROUP
+ OBJECTS { esmPortAutoSpeed, esmPortAutoDuplexMode
+ }
+ STATUS current
+ DESCRIPTION
+ "A collection of objects to support the Detected
+ configuration parameters of the Ethernet ports."
+ ::= { alcatelIND1PortMIBGroups 2 }
+
+alcEtherStatsMIBGroup OBJECT-GROUP
+ OBJECTS { alcetherClearStats, alcetherLastClearStats,
+ alcetherStatsCRCAlignErrors, alcetherStatsRxUndersizePkts,
+ alcetherStatsTxUndersizePkts, alcetherStatsTxOversizePkts,
+ alcetherStatsRxJabbers, alcetherStatsRxCollisions,
+ alcetherStatsTxCollisions, alcetherStatsPkts64Octets,
+ alcetherStatsPkts65to127Octets, alcetherStatsPkts128to255Octets,
+ alcetherStatsPkts256to511Octets,
+ alcetherStatsPkts512to1023Octets,
+ alcetherStatsPkts1024to1518Octets,
+ gigaEtherStatsPkts1519to4095Octets,
+ gigaEtherStatsPkts4096to9215Octets,
+ alcetherStatsPkts1519to2047Octets,
+ alcetherStatsPkts2048to4095Octets,
+ alcetherStatsPkts4096Octets,
+ alcetherStatsRxGiantPkts,
+ alcetherStatsRxDribbleNibblePkts,
+ alcetherStatsRxLongEventPkts,
+ alcetherStatsRxVlanTagPkts,
+ alcetherStatsRxControlPkts,
+ alcetherStatsRxLenChkErrPkts,
+ alcetherStatsRxCodeErrPkts,
+ alcetherStatsRxDvEventPkts,
+ alcetherStatsRxPrevPktDropped,
+ alcetherStatsTx64Octets,
+ alcetherStatsTx65to127Octets,
+ alcetherStatsTx128to255Octets,
+ alcetherStatsTx256to511Octets,
+ alcetherStatsTx512to1023Octets,
+ alcetherStatsTx1024to1518Octets,
+ alcetherStatsTx1519to2047Octets,
+ alcetherStatsTx2048to4095Octets,
+ alcetherStatsTx4096Octets,
+ alcetherStatsTxRetryCount,
+ alcetherStatsTxVlanTagPkts,
+ alcetherStatsTxControlPkts,
+ alcetherStatsTxLatePkts,
+ alcetherStatsTxTotalBytesOnWire,
+ alcetherStatsTxLenChkErrPkts,
+ alcetherStatsTxExcDeferPkts
+
+ }
+ STATUS current
+ DESCRIPTION
+ "A collection of objects to provide all the statistics related
+ to the Ethernet and GigaEthernert ports."
+ ::= { alcatelIND1PortMIBGroups 3 }
+
+alcPortNotificationGroup NOTIFICATION-GROUP
+ NOTIFICATIONS {
+ esmDrvTrapDropsLink
+ }
+ STATUS current
+ DESCRIPTION
+ "The Port MIB Notification Group."
+ ::= { alcatelIND1PortMIBGroups 4 }
+
+esmPortModeMIBGroup OBJECT-GROUP
+ OBJECTS { esmPortRunningMode,
+ esmPortSavedMode
+ }
+ STATUS current
+ DESCRIPTION
+ "A collection of objects to support the management of global
+ configuration parameters of the stacking ports."
+ ::= { alcatelIND1PortMIBGroups 5 }
+
+ ddmInfoGroup OBJECT-GROUP
+ OBJECTS {
+ ddmTemperature,
+ ddmTempLowWarning,
+ ddmTempLowAlarm,
+ ddmTempHiWarning,
+ ddmTempHiAlarm,
+ ddmSupplyVoltage,
+ ddmSupplyVoltageLowWarning,
+ ddmSupplyVoltageLowAlarm,
+ ddmSupplyVoltageHiWarning,
+ ddmSupplyVoltageHiAlarm,
+ ddmTxBiasCurrent,
+ ddmTxBiasCurrentLowWarning,
+ ddmTxBiasCurrentLowAlarm,
+ ddmTxBiasCurrentHiWarning,
+ ddmTxBiasCurrentHiAlarm,
+ ddmTxOutputPower,
+ ddmTxOutputPowerLowWarning,
+ ddmTxOutputPowerLowAlarm,
+ ddmTxOutputPowerHiWarning,
+ ddmTxOutputPowerHiAlarm,
+ ddmRxOpticalPower,
+ ddmRxOpticalPowerLowWarning,
+ ddmRxOpticalPowerLowAlarm,
+ ddmRxOpticalPowerHiWarning,
+ ddmRxOpticalPowerHiAlarm
+ }
+ STATUS current
+ DESCRIPTION
+ "A collection of objects to provide digital diagnostics information
+ related to SFPs, XFPs, and SFP+s."
+ ::= { alcatelIND1PortMIBGroups 6 }
+
+ ddmConfigGroup OBJECT-GROUP
+ OBJECTS {
+ ddmConfig,
+ ddmTrapConfig
+ }
+ STATUS current
+ DESCRIPTION
+ "A collection of objects to allow configuration of DDM and DDM traps."
+ ::= { alcatelIND1PortMIBGroups 7 }
+
+ ddmNotificationsGroup NOTIFICATION-GROUP
+ NOTIFICATIONS {
+ ddmTemperatureThresholdViolated,
+ ddmVoltageThresholdViolated,
+ ddmCurrentThresholdViolated,
+ ddmTxPowerThresholdViolated,
+ ddmRxPowerThresholdViolated
+ }
+ STATUS current
+ DESCRIPTION
+ "A collection of notifications used to indicate DDM threshold violations."
+ ::= { alcatelIND1PortMIBGroups 8 }
+
+ violationRecoveryGroup OBJECT-GROUP
+ OBJECTS {
+ esmViolationRecoveryTrap,
+ esmViolationRecoveryTime
+ }
+ STATUS current
+ DESCRIPTION
+ "A collection of objects to allow configuration of violationRecovery."
+ ::= { alcatelIND1PortMIBGroups 9 }
+
+ violationNotificationsGroup NOTIFICATION-GROUP
+ NOTIFICATIONS {
+ esmViolationRecoveryTimeout
+ }
+ STATUS current
+ DESCRIPTION
+ "A collection of notifications used to indicate esm violation recovery timeout."
+ ::= { alcatelIND1PortMIBGroups 10 }
+ END
+
+
generated by cgit v1.2.3 (git 2.46.0) at 2026-02-26 10:10:57 +0000