diff options
Diffstat (limited to 'MIBS/zyxel/ZYXEL-SAM1216')
| -rw-r--r-- | MIBS/zyxel/ZYXEL-SAM1216 | 5466 |
1 files changed, 5466 insertions, 0 deletions
diff --git a/MIBS/zyxel/ZYXEL-SAM1216 b/MIBS/zyxel/ZYXEL-SAM1216 new file mode 100644 index 0000000..4a75c0c --- /dev/null +++ b/MIBS/zyxel/ZYXEL-SAM1216 @@ -0,0 +1,5466 @@ +-- ZyXEL Communications Corporation +-- Private Enterprise MIB definition + +-- $Log: zyxel-SAM1216.mib $ +-- Revision 1.5 2010/03/17 10:24:51 cylien +-- Revision 1.4 2010/03/11 02:14:52 cylien +-- Revision 1.3 2009/10/09 02:10:10 cylien +-- Revision 1.2 2009/07/28 09:00:42 lbr +-- Revision 1.1 2008/07/11 09:36:01 maverick +-- Initial revision +-- Revision 1.3 2007/11/26 06:34:38 kenny +-- Revision 1.2 2007/09/19 02:44:42 niceguy +-- Revision 1.1 2006/08/28 05:32:54 kenny +-- Initial revision +-- Revision 1.5 2006/08/23 02:14:33 niceguy +-- Revision 1.4 2006/08/04 07:48:05 niceguy +-- Revision 1.3 2006/07/19 07:20:53 niceguy +-- Revision 1.2 2006/07/07 02:38:09 niceguy +-- Revision 1.1 2006/06/08 09:51:36 niceguy +-- Initial revision +-- Initial revision + + +ZYXEL-SAM1216 DEFINITIONS ::= BEGIN + + IMPORTS + + enterprises + FROM RFC1155-SMI + ifIndex, DisplayString, PhysAddress + FROM RFC1213-MIB + RowStatus + FROM SNMPv2-TC + dot1qVlanIndex, VlanIndex, PortList + FROM Q-BRIDGE-MIB + MacAddress, Timeout, BridgeId + FROM BRIDGE-MIB; + + zyxel OBJECT IDENTIFIER ::= { enterprises 890 } + products OBJECT IDENTIFIER ::= { zyxel 1 } + accessSwitch OBJECT IDENTIFIER ::= { products 5 } + sesSeries OBJECT IDENTIFIER ::= { accessSwitch 5 } + sam1216-22 OBJECT IDENTIFIER ::= { sesSeries 6 } + +-- acl OBJECT IDENTIFIER ::= { sam1216-22 1 } + alarmconf OBJECT IDENTIFIER ::= { sam1216-22 2 } +-- config OBJECT IDENTIFIER ::= { sam1216-22 3 } +-- diagnostic OBJECT IDENTIFIER ::= { sam1216-22 4 } +-- ipconf OBJECT IDENTIFIER ::= { sam1216-22 5 } +-- lcm OBJECT IDENTIFIER ::= { sam1216-22 6 } + multicast OBJECT IDENTIFIER ::= { sam1216-22 7 } + port OBJECT IDENTIFIER ::= { sam1216-22 8 } +-- profile OBJECT IDENTIFIER ::= { sam1216-22 9 } + switch OBJECT IDENTIFIER ::= { sam1216-22 10 } + sys OBJECT IDENTIFIER ::= { sam1216-22 11 } + trap OBJECT IDENTIFIER ::= { sam1216-22 12 } + statistics OBJECT IDENTIFIER ::= { sam1216-22 13 } + clear OBJECT IDENTIFIER ::= { sam1216-22 14 } +---------------------------------------- +-- acl +---------------------------------------- +-- Standalone IP DSLAM puts all ACL features in 'switch', from OID 51 + + dhcp OBJECT IDENTIFIER ::= { switch 51 } +-- dot1x OBJECT IDENTIFIER ::= { switch 52 } + macfilter OBJECT IDENTIFIER ::= { switch 53 } +-- pktfilter OBJECT IDENTIFIER ::= { switch 54 } + dhcpSnoop OBJECT IDENTIFIER ::= { switch 55 } + acl OBJECT IDENTIFIER ::= { switch 56 } + pppoeAgent OBJECT IDENTIFIER ::= { switch 57 } + +-------------------- +-- DHCP Relay +-------------------- + + dhcpRelayEnable OBJECT-TYPE + SYNTAX INTEGER { + auto(1), + both(2), + disable(3) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Enable/disable DHCP relay Option82 function." + ::= { dhcp 1 } + + dhcpRelay82Table OBJECT-TYPE + SYNTAX SEQUENCE OF DhcpRelay82Entry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains DHCP Relay configuration." + ::= { dhcp 2 } + + dhcpRelay82Entry OBJECT-TYPE + SYNTAX DhcpRelay82Entry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The entry of DHCP Relay table." + INDEX { dot1qVlanIndex } + ::= { dhcpRelay82Table 1 } + + DhcpRelay82Entry ::= + SEQUENCE { + dhcpRelay82PrimaryServer IpAddress, + dhcpRelay82SecondaryServer IpAddress, + dhcpRelay82ActiveServer INTEGER, + dhcpRelay82Enable INTEGER, + dhcpRelay82Info DisplayString, + dhcpRelay82RelayMode INTEGER, + dhcpRelay82Suboption2Enable INTEGER, + dhcpRelay82Suboption2Info DisplayString, + dhcpRelay82EntryEnable INTEGER, + dhcpRelay82EntryOptionMode INTEGER + } + + dhcpRelay82PrimaryServer OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The IP address of the DHCP Relay primary server." + ::= { dhcpRelay82Entry 1 } + + dhcpRelay82SecondaryServer OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The IP address of the DHCP Relay secondary server." + ::= { dhcpRelay82Entry 2 } + + dhcpRelay82ActiveServer OBJECT-TYPE + SYNTAX INTEGER { + primary(1), + secondary(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The current active DHCP Relay server." + ::= { dhcpRelay82Entry 3 } + + + dhcpRelay82Enable OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Enable/disable DHCP relay and Option82 function." + ::= { dhcpRelay82Entry 4 } + + dhcpRelay82Info OBJECT-TYPE + SYNTAX DisplayString (SIZE (0..23)) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "User specific Option82 information." + ::= { dhcpRelay82Entry 5 } + + dhcpRelay82RelayMode OBJECT-TYPE + SYNTAX INTEGER { + auto(1), + both(2) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "DHCP relay mode." + ::= { dhcpRelay82Entry 6 } + + + dhcpRelay82Suboption2Enable OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Enable/disable Option 82 sub-option 2." + ::= { dhcpRelay82Entry 8 } + + dhcpRelay82Suboption2Info OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "User specified information for Option 82 sub-option 2." + ::= { dhcpRelay82Entry 9 } + + dhcpRelay82EntryEnable OBJECT-TYPE + SYNTAX INTEGER { + auto(1), + both(2), + disable(3) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Enable/disable DHCP Relay" + ::= { dhcpRelay82Entry 10 } + + dhcpRelay82EntryOptionMode OBJECT-TYPE + SYNTAX INTEGER { + private(1), + tr101(2), + tr101WithVlan(3) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Option82 format." + ::= { dhcpRelay82Entry 11 } + + dhcpRelayOption82Sub1Info OBJECT-TYPE + SYNTAX DisplayString (SIZE (0..23)) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "User specific Option82 subOption1 (Agent circuit ID) information." + ::= { dhcp 3 } + + maxNumOfDhcpRelay82Conf OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The maximum number of rows that can be created in dhcpRelay82Table." + ::= { dhcp 4 } + + dhcpRelayOption82Sub1Enable OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Enable/disable DHCP relay Option82 subOption1 (Agent Circuit ID) function." + ::= { dhcp 5 } + + dhcpRelayOption82Sub2Info OBJECT-TYPE + SYNTAX DisplayString (SIZE (0..23)) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "User specific Option82 subOption2 (Agent Remote ID) information." + ::= { dhcp 6 } + + dhcpRelayOption82Sub2Enable OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Enable/disable DHCP relay Option82 subOption2 (Agent Remote ID) function." + ::= { dhcp 7 } + +-------------------- +-- MAC Filter +-------------------- + +-- MAC Filter Port Table + + macFilterPortTable OBJECT-TYPE + SYNTAX SEQUENCE OF MacFilterPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes the status of mac filtering for each port." + ::= { macfilter 1 } + + macFilterPortEntry OBJECT-TYPE + SYNTAX MacFilterPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in macFilterPortTable." + INDEX { ifIndex } + ::= { macFilterPortTable 1 } + + MacFilterPortEntry ::= + SEQUENCE { + macFilterPortEnable INTEGER, + macFilterPortMacCount INTEGER, + macFilterPortFilterMode INTEGER + } + + macFilterPortEnable OBJECT-TYPE + SYNTAX INTEGER { + enableMacFilter(1), + enableMacCount(2), +-- enableOuiFilter(3), + disable(4), + enableMacFilterAndMacCount(5) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Enable/disable MAC filtering for the port." + ::= { macFilterPortEntry 1 } + + macFilterPortMacCount OBJECT-TYPE + SYNTAX INTEGER (1..128) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The total number of MAC addresses allowed for the port." + ::= { macFilterPortEntry 2 } + + macFilterPortFilterMode OBJECT-TYPE + SYNTAX INTEGER { + accept(1), + deny(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The mac filter mode (accept or deny) for the port." + ::= { macFilterPortEntry 3 } + + maxNumOfMacFiltersInSystem OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The max number of mac filters supported in the system." + ::= { macfilter 2 } + + maxNumOfMacFiltersPerPort OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The max number of mac filters supported per port." + ::= { macfilter 3 } + + currNumOfMacFiltersInSystem OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The current number of mac filters in the system." + ::= { macfilter 4 } + +-- MAC Table + + macFilterTable OBJECT-TYPE + SYNTAX SEQUENCE OF MacFilterEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains the mac filter addresses." + ::= { macfilter 5 } + + macFilterEntry OBJECT-TYPE + SYNTAX MacFilterEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The entry of macFilterTable." + INDEX { ifIndex, macFilterAddr } + ::= { macFilterTable 1 } + + MacFilterEntry ::= + SEQUENCE { + macFilterAddr PhysAddress, + macFilterRowStatus RowStatus + } + + macFilterAddr OBJECT-TYPE + SYNTAX PhysAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The mac address which can pass through or be rejected from the port." + ::= { macFilterEntry 1 } + + macFilterRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The row status of the entry." + ::= { macFilterEntry 2 } + +-- Batch Set for MAC Filter + + macfilterBatchSet OBJECT IDENTIFIER ::= { macfilter 6 } + + macfilterTarget OBJECT-TYPE + SYNTAX OCTET STRING + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This managed object is used for identify the target on which + the port configuration should be performed. The target is encoded as: + Byte 1: 0, Reserved(chassis) + Byte 2~3: 0, Reserved(slot) + Byte 4: 0, reserved + Byte 5~11:each octet specifies a set of eight ports, with the first + octet specifying ports 1 through 8, etc." + ::= { macfilterBatchSet 1 } + + macfilterOps OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The corresponding bit is set to 1 to start the operation. + The various bit positions are: + BIT 1: enable mac filter + BIT 2: enable mac count filter + BIT 3: disable mac filter + BIT 4: set mac count + BIT 5: disable mac count filter." + ::= { macfilterBatchSet 2 } + + macFilterMacCountForBatchSet OBJECT-TYPE + SYNTAX INTEGER (1..128) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The total number of MAC addresses allowed for a port." + ::= { macfilterBatchSet 3 } + + +-- OUI Filter Table + + ouiFilterTable OBJECT-TYPE + SYNTAX SEQUENCE OF OuiFilterEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains the OUI filter addresses." + ::= { macfilter 7 } + + ouiFilterEntry OBJECT-TYPE + SYNTAX OuiFilterEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The entry of ouiFilterTable." + INDEX { ifIndex, ouiFilterAddr } + ::= { ouiFilterTable 1 } + + OuiFilterEntry ::= + SEQUENCE { + ouiFilterAddr OCTET STRING, + ouiFilterRowStatus RowStatus + } + + ouiFilterAddr OBJECT-TYPE + SYNTAX OCTET STRING + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The first three bytes of the mac address which can pass through or be rejected from the port." + ::= { ouiFilterEntry 1 } + + ouiFilterRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The row status of the entry." + ::= { ouiFilterEntry 2 } + + maxNumOfOuiFiltersPerPort OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The max number of OUI filters supported per port." + ::= { macfilter 8 } + + + ouiFilterPortTable OBJECT-TYPE + SYNTAX SEQUENCE OF OuiFilterPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes the status of oui filtering for each port." + ::= { macfilter 9 } + + ouiFilterPortEntry OBJECT-TYPE + SYNTAX OuiFilterPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in macFilterPortTable." + INDEX { ifIndex } + ::= { ouiFilterPortTable 1 } + + OuiFilterPortEntry ::= + SEQUENCE { + ouiFilterPortEnable INTEGER, + ouiFilterPortFilterMode INTEGER + } + + + ouiFilterPortEnable OBJECT-TYPE + SYNTAX INTEGER { + enableOuiFilter(1), + disable(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Enable/disable oui filtering for the port." + ::= { ouiFilterPortEntry 1 } + + + + ouiFilterPortFilterMode OBJECT-TYPE + SYNTAX INTEGER { + accept(1), + deny(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The oui filter mode (accept or deny) for the port." + ::= { ouiFilterPortEntry 2 } +-------------------- +-- DHCP Snoop +-------------------- + +-- dhcpSnoopPortTable + + dhcpSnoopPortTable OBJECT-TYPE + SYNTAX SEQUENCE OF DhcpSnoopPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes DHCP snooping enable/disable for each port." + ::= { dhcpSnoop 1 } + + dhcpSnoopPortEntry OBJECT-TYPE + SYNTAX DhcpSnoopPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of dhcpSnoopPortTable." + INDEX { ifIndex } + ::= { dhcpSnoopPortTable 1 } + + DhcpSnoopPortEntry ::= + SEQUENCE { + dhcpSnoopEnable INTEGER + } + + dhcpSnoopEnable OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Enable/disable DHCP snooping for a port." + ::= { dhcpSnoopPortEntry 1 } + +-- dhcpSnoopOperation + + dhcpSnoopTarget OBJECT-TYPE + SYNTAX OCTET STRING + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This managed object is used for identify the target on which + the operation should be performed. The target is encoded as: + Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 + Byte 2~3: each octet specifies a set of eight slots, with the + first octet specifying slots 1 through 8 and the second + octet specifying slots 9 through 16. + Byte 4: reserved + Byte 5~11:each octet specifies a set of eight ports, with the first + octet specifying ports 1 through 8, etc." + ::= { dhcpSnoop 2 } + + dhcpSnoopOps OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The corresponding bit is set to 1 to start the operation. + The various bit positions are: + BIT 1: DHCP snooping table flush." + ::= { dhcpSnoop 3 } + + +-- dhcpStaticTable + + dhcpStaticTable OBJECT-TYPE + SYNTAX SEQUENCE OF DhcpStaticEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table defines DHCP static IP addresses." + ::= { dhcpSnoop 4 } + + dhcpStaticEntry OBJECT-TYPE + SYNTAX DhcpStaticEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of dhcpStaticTable." + INDEX { ifIndex, dhcpStaticIpAddr } + ::= { dhcpStaticTable 1 } + + DhcpStaticEntry ::= + SEQUENCE { + dhcpStaticIpAddr IpAddress, + dhcpStaticRowStatus RowStatus + } + + dhcpStaticIpAddr OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The IP address which can pass through the port." + ::= { dhcpStaticEntry 1 } + + dhcpStaticRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Row status of the table entry." + ::= { dhcpStaticEntry 2 } + + maxNumOfDhcpStaticIp OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The maximum number of DHCP static IP addresses which can be created for a port." + ::= { dhcpSnoop 5 } + + dhcpSnoopLan2lanEnable OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Enable/disable DHCP snoop lan2lan function." + ::= { dhcpSnoop 6 } + +-- acl +--aclSetTable + aclSetTable OBJECT-TYPE + SYNTAX SEQUENCE OF AclSetEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "aclsetTable." + ::= { acl 1 } + + aclSetEntry OBJECT-TYPE + SYNTAX AclSetEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of aclSetTable." + INDEX { ifIndex, aclSetVpi, aclSetVci, aclSetProfileName } + ::= { aclSetTable 1 } + + AclSetEntry ::= + SEQUENCE { + aclSetVpi INTEGER, + aclSetVci INTEGER, + aclSetProfileName DisplayString, + aclSetRowStatus RowStatus + } + + aclSetVpi OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VPI value" + ::= { aclSetEntry 1 } + + aclSetVci OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VCI value" + ::= { aclSetEntry 2 } + + aclSetProfileName OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "ACL Profile name" + ::= { aclSetEntry 3 } + + aclSetRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "RowStatus of aclSetEntry" + ::= { aclSetEntry 4 } + +--aclProfileTable + + aclProfileTable OBJECT-TYPE + SYNTAX SEQUENCE OF AclProfileEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "aclProfileTable." + ::= { acl 2 } + + aclProfileEntry OBJECT-TYPE + SYNTAX AclProfileEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of aclProfileTable." + INDEX { aclProfileRuleName } + ::= { aclProfileTable 1 } + + AclProfileEntry ::= + SEQUENCE { + aclProfileRuleName DisplayString, + aclProfileRuleNumber INTEGER, + aclProfileActionNumber INTEGER, + aclProfileRuleParamMask INTEGER, + aclProfileRuleEtype INTEGER, + aclProfileRuleVid INTEGER, + aclProfileRuleSmac PhysAddress, + aclProfileRuleDmac PhysAddress, + aclProfileRulePriority INTEGER, + aclProfileRuleProtocol INTEGER, + aclProfileRuleSrcIP IpAddress, + aclProfileRuleSrcIPMask INTEGER, + aclProfileRuleDestIP IpAddress, + aclProfileRuleDestIPMask INTEGER, + aclProfileRuleStartTos INTEGER, + aclProfileRuleEndTos INTEGER, + aclProfileRuleSrcStartPort INTEGER, + aclProfileRuleSrcEndPort INTEGER, + aclProfileRuleDestStartPort INTEGER, + aclProfileRuleDestEndPort INTEGER, + aclProfileActionRate INTEGER, + aclProfileActionrvlan INTEGER, + aclProfileActionrpri INTEGER, + aclProfileRowStatus RowStatus + } + + aclProfileRuleName OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Profile rule name" + ::= { aclProfileEntry 1 } + + aclProfileRuleNumber OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The managed object is for acl profile rule configuration. + etype <etype> vlan <vid> (1), + etype <etype> smac <mac> (2), + etype <etype> dmac <mac> (3), + vlan <vid> smac <mac> (4), + vlan <vid> dmac <mac> (5), + smac <mac> dmac <mac> (6), + vlan <vid> priority <priority> (7), + etype <etype> (8), + vlan <vid> (9), + smac <mac> (10), + dmac <mac> (11), + priority <priority> (12), + protocol <protocol> (13), + {srcip <ip>/<mask>{|dstip <ip>/<mask>{|tos <stos> <etos>{|srcport <sport> <eport> {|dstport <sport> <eport>}}}}} (14) " + ::= { aclProfileEntry 2 } + + aclProfileActionNumber OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile action number. + Bit 1: rate + Bit 2: rvlan + Bit 3: rpri + Bit 4: deny + + Bit 1, Bit 2 & Bit 3 can multiple selection." + ::= { aclProfileEntry 3 } + + aclProfileRuleParamMask OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule parameter mask. + + BIT 1: srcip <ip>/<mask> + BIT 2: dstip <ip>/<mask> + BIT 3: tos <stos> <etos> + BIT 4: srcport <sport> <eport> + BIT 5: dstport <sport> <eport> + " + ::= { aclProfileEntry 4 } + + aclProfileRuleEtype OBJECT-TYPE + SYNTAX INTEGER (0..65535) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule etype + " + ::= { aclProfileEntry 5 } + + aclProfileRuleVid OBJECT-TYPE + SYNTAX INTEGER (1..4094) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule vid" + ::= { aclProfileEntry 6 } + + aclProfileRuleSmac OBJECT-TYPE + SYNTAX PhysAddress + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule source MAC" + ::= { aclProfileEntry 7 } + + aclProfileRuleDmac OBJECT-TYPE + SYNTAX PhysAddress + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule destination MAC" + ::= { aclProfileEntry 8 } + + aclProfileRulePriority OBJECT-TYPE + SYNTAX INTEGER (1..7) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule priority" + ::= { aclProfileEntry 9 } + + aclProfileRuleProtocol OBJECT-TYPE + SYNTAX INTEGER (0..65535) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule protocol. + icmp(1),igmp(2),ip(4),tcp(6), + udp(17),gre(47),ospf(89), + other ptype" + ::= { aclProfileEntry 10 } + + aclProfileRuleSrcIP OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule source IP" + ::= { aclProfileEntry 11 } + + aclProfileRuleSrcIPMask OBJECT-TYPE + SYNTAX INTEGER (0..32) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The subnet mask of source IP mask" + ::= { aclProfileEntry 12 } + + aclProfileRuleDestIP OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule source IP" + ::= { aclProfileEntry 13 } + + aclProfileRuleDestIPMask OBJECT-TYPE + SYNTAX INTEGER (0..32) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The subnet mask of dest IP mask" + ::= { aclProfileEntry 14 } + + aclProfileRuleStartTos OBJECT-TYPE + SYNTAX INTEGER (0..255) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule start type of service" + ::= { aclProfileEntry 15 } + + aclProfileRuleEndTos OBJECT-TYPE + SYNTAX INTEGER (0..255) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule end type of service" + ::= { aclProfileEntry 16 } + + aclProfileRuleSrcStartPort OBJECT-TYPE + SYNTAX INTEGER (0..65535) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule source start port" + ::= { aclProfileEntry 17 } + + aclProfileRuleSrcEndPort OBJECT-TYPE + SYNTAX INTEGER (0..65535) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule source end port" + ::= { aclProfileEntry 18 } + + aclProfileRuleDestStartPort OBJECT-TYPE + SYNTAX INTEGER (0..65535) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule destination start port" + ::= { aclProfileEntry 19 } + + aclProfileRuleDestEndPort OBJECT-TYPE + SYNTAX INTEGER (0..65535) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile rule destination end port" + ::= { aclProfileEntry 20 } + + aclProfileActionRate OBJECT-TYPE + SYNTAX INTEGER (1..65535) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile action to replace to this rate" + ::= { aclProfileEntry 21 } + + aclProfileActionrvlan OBJECT-TYPE + SYNTAX INTEGER (1..4094) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile action to replace to this vlan" + ::= { aclProfileEntry 22 } + + aclProfileActionrpri OBJECT-TYPE + SYNTAX INTEGER (1..7) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Profile action to replace to this priority" + ::= { aclProfileEntry 23 } + + aclProfileRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The row status of the entry." + ::= { aclProfileEntry 24 } + +-------------------- +-- PPPoE Agent +-------------------- + +-- pppoeAgentTable + + pppoeAgentTable OBJECT-TYPE + SYNTAX SEQUENCE OF PppoeAgentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains PPPoE DHCP Relay configuration." + ::= { pppoeAgent 1 } + + pppoeAgentEntry OBJECT-TYPE + SYNTAX PppoeAgentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of pppoeAgentTable." + INDEX { dot1qVlanIndex } + ::= { pppoeAgentTable 1 } + + PppoeAgentEntry ::= + SEQUENCE { + pppoeAgentEnable INTEGER, + pppoeAgentInfo DisplayString, + pppoeAgentRowStatus RowStatus, + pppoeAgentOptionMode INTEGER + } + + pppoeAgentEnable OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Enable/disable DHCP relay and Option82 function." + ::= { pppoeAgentEntry 1 } + + pppoeAgentInfo OBJECT-TYPE + SYNTAX DisplayString (SIZE (0..23)) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "User specific Option82 information." + ::= { pppoeAgentEntry 2 } + + pppoeAgentRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Row status of the table entry." + ::= { pppoeAgentEntry 3 } + + pppoeAgentOptionMode OBJECT-TYPE + SYNTAX INTEGER { + private(1), + tr101(2), + tr101WithVlan(3) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Option82 format." + ::= { pppoeAgentEntry 4 } + + + maxNumOfPppoeAgentConf OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The maximum number of rows that can be created in pppoeAgentTable." + ::= { pppoeAgent 2 } + +---------------------------------------- +-- alarmconf +---------------------------------------- + + alarmOps OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The manager sets the corresponding bit value to 1 to start the operation + and the agent clears the object to zero when the operation is successfully completed. + The various bit positions are: + BIT 1: clear + BIT 2: cutoff" + ::= { alarmconf 1 } + +-- Alarm Conf Table + + alarmConfTable OBJECT-TYPE + SYNTAX SEQUENCE OF AlarmConfEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes alarm configuration." + ::= { alarmconf 2 } + + alarmConfEntry OBJECT-TYPE + SYNTAX AlarmConfEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in alarmConfTable." + INDEX { alarmConfId } + ::= { alarmConfTable 1 } + + AlarmConfEntry ::= + SEQUENCE { + alarmConfId INTEGER, + alarmConfFacility INTEGER, + alarmConfTarget INTEGER, + alarmConfSeverity INTEGER, + alarmConfClearable INTEGER + } + + alarmConfId OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "5000: linkUp + 5001: linkDown + 5002: shdslLoopAttenCrossing + 5003: shdslSNRMarginCrossing + 5004: shdslPerfESThresh + 5005: shdslPerfSESThresh + 5006: shdslPerfCRCAnomaliesThresh + 5007: shdslPerfLOSWSThresh + 5008: shdslPerfUASThresh + 10000: eqptVoltageError + 10001: eqptTempError + 10002: eqptHwRTCError + 10003: eqptHWMonitorFailed + 10004: coldStart + 10005: warmStart + 15000: sysReboot + 15001: sysAlarmCutoffEnabled + 15002: sysAlarmClearEnabled + 15003: sysLoginFailed + 15004: sysMacAntiSpoofing + 20000: enetlinkUp + 20001: enetlinkDown" + ::= { alarmConfEntry 1 } + + alarmConfFacility OBJECT-TYPE + SYNTAX INTEGER { + local1(1), + local2(2), + local3(3), + local4(4), + local5(5), + local6(6), + local7(7) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Alarm facility." + ::= { alarmConfEntry 2 } + + alarmConfTarget OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The destination which alarms are reported to. Set the bit to 1 to enable the target. + BIT 1: snmp trap + BIT 2: syslog" + ::= { alarmConfEntry 3 } + + alarmConfSeverity OBJECT-TYPE + SYNTAX INTEGER { + critical(1), + major(2), + minor(3), + info(4) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Alarm severity" + ::= { alarmConfEntry 4 } + + alarmConfClearable OBJECT-TYPE + SYNTAX INTEGER { + clearable(1), + unclearable(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Setting the object to one indicates that the alarm is to be cleared when user submits alarm clear." + ::= { alarmConfEntry 5 } + +-- Alarm Current Table + + alarmCurrTable OBJECT-TYPE + SYNTAX SEQUENCE OF AlarmCurrEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes current alarm information." + ::= { alarmconf 3 } + + alarmCurrEntry OBJECT-TYPE + SYNTAX AlarmCurrEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in alarmCurrTable." + INDEX { alarmCurrIndex } + ::= { alarmCurrTable 1 } + + AlarmCurrEntry ::= + SEQUENCE { + alarmCurrIndex INTEGER, + alarmCurrOccurTime TimeTicks, + alarmCurrTrapOid OBJECT IDENTIFIER, + alarmCurrParam1 INTEGER, + alarmCurrParam2 INTEGER, + alarmCurrParam3 INTEGER, + alarmCurrParam4 INTEGER, + alarmCurrParam5 INTEGER, + alarmCurrParam6 INTEGER, + alarmCurrParam7 INTEGER, + alarmCurrParam8 INTEGER, + alarmCurrTimeDescr DisplayString, + alarmCurrSeverity INTEGER, + alarmCurrDescr DisplayString + } + + alarmCurrIndex OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Index of the alarm." + ::= { alarmCurrEntry 1 } + + alarmCurrOccurTime OBJECT-TYPE + SYNTAX TimeTicks + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Alarm occurence time (in hundredths of a second) since the system was last re-initialized." + ::= { alarmCurrEntry 2 } + + alarmCurrTrapOid OBJECT-TYPE + SYNTAX OBJECT IDENTIFIER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Trap OID of the alarm." + ::= { alarmCurrEntry 3 } + + alarmCurrParam1 OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The 1st parameter of the alarm." + ::= { alarmCurrEntry 4 } + + alarmCurrParam2 OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The 2nd parameter of the alarm." + ::= { alarmCurrEntry 5 } + + alarmCurrParam3 OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The 3rd parameter of the alarm." + ::= { alarmCurrEntry 6 } + + alarmCurrParam4 OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The 4th parameter of the alarm." + ::= { alarmCurrEntry 7 } + + alarmCurrParam5 OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The 5th parameter of the alarm." + ::= { alarmCurrEntry 8 } + + alarmCurrParam6 OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The 6th parameter of the alarm." + ::= { alarmCurrEntry 9 } + + alarmCurrParam7 OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The 7th parameter of the alarm." + ::= { alarmCurrEntry 10 } + + alarmCurrParam8 OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The 8th parameter of the alarm." + ::= { alarmCurrEntry 11 } + + alarmCurrTimeDescr OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The string representation of occurence time (YYYY/MM/DD HH:MM:SS)." + ::= { alarmCurrEntry 12 } + + alarmCurrSeverity OBJECT-TYPE + SYNTAX INTEGER { + critical(1), + major(2), + minor(3), + info(4) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The severity of the alarm." + ::= { alarmCurrEntry 13 } + + alarmCurrDescr OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The description of the alarm." + ::= { alarmCurrEntry 14 } + +-- Alarm Severity Port Table + + alarmSeverityPortTable OBJECT-TYPE + SYNTAX SEQUENCE OF AlarmSeverityPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes the configuration of alarm reporting severity threshold for each port." + ::= { alarmconf 4 } + + alarmSeverityPortEntry OBJECT-TYPE + SYNTAX AlarmSeverityPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in alarmSeverityPortTable." + INDEX { ifIndex } + ::= { alarmSeverityPortTable 1 } + + AlarmSeverityPortEntry ::= + SEQUENCE { + severityThresh INTEGER + } + + severityThresh OBJECT-TYPE + SYNTAX INTEGER { + critical(1), + major(2), + minor(3), + info(4) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The minimum alarm severity that is reported." + ::= { alarmSeverityPortEntry 1 } + +---------------------------------------- +-- diagnostic +---------------------------------------- + +-- loopback OBJECT IDENTIFIER ::= { diagnostic 1 } +-- ldm OBJECT IDENTIFIER ::= { diagnostic 2 } +-- selt OBJECT IDENTIFIER ::= { diagnostic 3 } +-- + +-------------------- +-- selt +-------------------- + +-- seltTarget OBJECT-TYPE +-- SYNTAX INTEGER +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "IfIndex of the port which would be performed single end loopback test." +-- ::= { selt 1 } +-- +-- seltOps OBJECT-TYPE +-- SYNTAX INTEGER +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The manager sets the object to 1 to start the selt +-- and the agent clears the object to zero when selt is successfully completed." +-- ::= { selt 2 } +-- +-- seltStatus OBJECT-TYPE +-- SYNTAX DisplayString +-- MAX-ACCESS read-only +-- STATUS current +-- DESCRIPTION +-- "Status description of the selt result." +-- ::= { selt 3 } +-- +-- seltCableType OBJECT-TYPE +-- SYNTAX INTEGER { +-- awg24(1), +-- awg26(2) +-- } +-- MAX-ACCESS read-only +-- STATUS current +-- DESCRIPTION +-- "The cable type that selt result indicates." +-- ::= { selt 4 } +-- +-- seltLoopEstimateLengthFt OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "feet" +-- MAX-ACCESS read-only +-- STATUS current +-- DESCRIPTION +-- "The estimated loop length that selt result indicates." +-- ::= { selt 5 } +-- +-- seltLoopEstimateLengthMeter OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "meter" +-- MAX-ACCESS read-only +-- STATUS current +-- DESCRIPTION +-- "The estimated loop length that selt result indicates." +-- ::= { selt 6 } + + +---------------------------------------- +-- multicast +---------------------------------------- + +-- staticMulticast OBJECT IDENTIFIER ::= { multicast 2 } +-- igmpFilter OBJECT IDENTIFIER ::= { multicast 3 } + mcastBandwidth OBJECT IDENTIFIER ::= { multicast 4 } + igmpCount OBJECT IDENTIFIER ::= { multicast 5 } + mvlan OBJECT IDENTIFIER ::= { multicast 6 } + queryVid OBJECT IDENTIFIER ::= { multicast 7 } + + igmpEnable OBJECT-TYPE + SYNTAX INTEGER { + enableProxy(1), + enableSnooping(2), + disable(3) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Enable/disable IGMP protocol." + ::= { multicast 1 } + +-- igmpMode OBJECT-TYPE +-- SYNTAX INTEGER { +-- aggresive(1), +-- normal(2) +-- } +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "setting IGMP with aggresive mode will issue an IGMP report from new active port +-- when topology change occurs, while normal mode won't." +-- ::= { multicast 8 } + +-------------------- +-- bandwidth +-------------------- + + mcastDefaultBandwidth OBJECT-TYPE + SYNTAX INTEGER (1..100000) + UNITS "Kbps" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Default bandwidth requirement for a multicast channel." + ::= { mcastBandwidth 1 } + + maxNumOfMcastBw OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The maximum number of row entries that user can create in mcastBwTable." + ::= { mcastBandwidth 2 } + +-- mcastBwTable + + mcastBwTable OBJECT-TYPE + SYNTAX SEQUENCE OF McastBwEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table defines bandwidth budget for a range of multicast IP channels." + ::= { mcastBandwidth 3 } + + mcastBwEntry OBJECT-TYPE + SYNTAX McastBwEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of mcastBwTable." + INDEX { mcastBwIndex, mcastBwStartIp, mcastBwEndIp } + ::= { mcastBwTable 1 } + + McastBwEntry ::= + SEQUENCE { + mcastBwIndex INTEGER, + mcastBwStartIp IpAddress, + mcastBwEndIp IpAddress, + mcastBwBandwidth INTEGER, + mcastBwRowStatus RowStatus + } + + mcastBwIndex OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The index which specify the entry." + ::= { mcastBwEntry 1 } + + mcastBwStartIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The start multicast IP of the bandwidth control range." + ::= { mcastBwEntry 2 } + + mcastBwEndIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The end multicast IP of the bandwidth control range." + ::= { mcastBwEntry 3 } + + mcastBwBandwidth OBJECT-TYPE + SYNTAX INTEGER + UNITS "Kbps" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The bandwidth budget for the multicast IP channels." + ::= { mcastBwEntry 4 } + + mcastBwRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The row status of the entry." + ::= { mcastBwEntry 5 } + +-- mcastBwPortTable + + mcastBwPortTable OBJECT-TYPE + SYNTAX SEQUENCE OF McastBwPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table specify the multicast bandwidth control of the port." + ::= { mcastBandwidth 4 } + + mcastBwPortEntry OBJECT-TYPE + SYNTAX McastBwPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of mcastBwPortTable." + INDEX { ifIndex } + ::= { mcastBwPortTable 1 } + + McastBwPortEntry ::= + SEQUENCE { + mcastBwPortEnable INTEGER, + mcastBwPortBandwidth INTEGER + } + + mcastBwPortEnable OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Enable/disable multicast bandwidth control for a port." + ::= { mcastBwPortEntry 1 } + + mcastBwPortBandwidth OBJECT-TYPE + SYNTAX INTEGER + UNITS "Kbps" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Set bandwidth threshold for a port." + ::= { mcastBwPortEntry 2 } + +-------------------- +-- igmpCount +-------------------- + + igmpCountPortTable OBJECT-TYPE + SYNTAX SEQUENCE OF IgmpCountPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table specify the IGMP count limiting of the port." + ::= { igmpCount 1 } + + igmpCountPortEntry OBJECT-TYPE + SYNTAX IgmpCountPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of igmpCountPortTable." + INDEX { ifIndex } + ::= { igmpCountPortTable 1 } + + IgmpCountPortEntry ::= + SEQUENCE { + igmpCountPortEnable INTEGER, + igmpCountPortLimit INTEGER + } + + igmpCountPortEnable OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Enable/disable IGMP count limiting for a port." + ::= { igmpCountPortEntry 1 } + + igmpCountPortLimit OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The maximum allowed IGMP report count for a port." + ::= { igmpCountPortEntry 2 } + +-------------------- +-- mvlan +-------------------- + + maxNumOfMvlan OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The maximum number of row entries that user can create in mvlanTable." + ::= { mvlan 1 } + +-- mvlanTable + + mvlanTable OBJECT-TYPE + SYNTAX SEQUENCE OF MvlanEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table containing static configuration information for + each multicast VLAN configured into the device." + ::= { mvlan 2 } + + mvlanEntry OBJECT-TYPE + SYNTAX MvlanEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of mvlanTable." + INDEX { mvlanIndex } + ::= { mvlanTable 1 } + + MvlanEntry ::= + SEQUENCE { + mvlanIndex VlanIndex, + mvlanName DisplayString, + mvlanEgressPorts PortList, + mvlanUntaggedPorts PortList, + mvlanRowStatus RowStatus + } + + mvlanIndex OBJECT-TYPE + SYNTAX VlanIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The VLAN-ID refering to this VLAN." + ::= { mvlanEntry 1 } + + mvlanName OBJECT-TYPE + SYNTAX DisplayString (SIZE (0..31)) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "An administratively assigned string, which may be used to identify the VLAN." + ::= { mvlanEntry 2 } + + mvlanEgressPorts OBJECT-TYPE + SYNTAX PortList + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The set of ports which are permanently assigned to the + egress list for this multicast VLAN." + ::= { mvlanEntry 3 } + + mvlanUntaggedPorts OBJECT-TYPE + SYNTAX PortList + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The set of ports which should transmit egress packets + for this multicast VLAN as untagged." + ::= { mvlanEntry 4 } + + mvlanRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object indicates the status of this entry." + ::= { mvlanEntry 5 } + +-- mvlanTranslateTable + + mvlanTranslateTable OBJECT-TYPE + SYNTAX SEQUENCE OF MvlanTranslateEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains multicast to VLAN translation." + ::= { mvlan 3 } + + mvlanTranslateEntry OBJECT-TYPE + SYNTAX MvlanTranslateEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of mvlanTranslateTable." + INDEX { dot1qVlanIndex, mvlanTranslateIndex } + ::= { mvlanTranslateTable 1 } + + MvlanTranslateEntry ::= + SEQUENCE { + mvlanTranslateIndex INTEGER, + mvlanTranslateStartIp IpAddress, + mvlanTranslateEndIp IpAddress + } + + mvlanTranslateIndex OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The index which specif the entry." + ::= { mvlanTranslateEntry 1 } + + mvlanTranslateStartIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The start IP of the multicast VLAN translation." + ::= { mvlanTranslateEntry 2 } + + mvlanTranslateEndIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The end IP of the multicast VLAN translation." + ::= { mvlanTranslateEntry 3 } + + +-------------------- +-- queryVid +-------------------- + + maxNumOfQryVid OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The maximum number of row entries that user can create in qryVidConfTable. + This object is supported by R1.02 and later versions." + ::= { queryVid 1 } + +-- qryVidConfTable + + qryVidConfTable OBJECT-TYPE + SYNTAX SEQUENCE OF QryVidConfEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table defines statically set VLANs used for response IGMP report. + This table is supported by R1.02 and later versions." + ::= { queryVid 2 } + + qryVidConfEntry OBJECT-TYPE + SYNTAX QryVidConfEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in qryVidConfTable." + INDEX { qryVid } + ::= { qryVidConfTable 1 } + + QryVidConfEntry ::= + SEQUENCE { + qryVid INTEGER, + qryVidRowStatus RowStatus + } + + qryVid OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VLAN ID." + ::= { qryVidConfEntry 1 } + + qryVidRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object indicates the status of this entry." + ::= { qryVidConfEntry 2 } + +-- qryVidStatusTable + + qryVidStatusTable OBJECT-TYPE + SYNTAX SEQUENCE OF QryVidStatusEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table shows statically set or dynamically learned VLANs used for response IGMP report." + ::= { queryVid 3 } + + qryVidStatusEntry OBJECT-TYPE + SYNTAX QryVidStatusEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in qryVidStatusTable." + INDEX { qryVid } + ::= { qryVidStatusTable 1 } + + QryVidStatusEntry ::= + SEQUENCE { + qryVidType INTEGER + } + + qryVidType OBJECT-TYPE + SYNTAX INTEGER { + static(1), + dynamic(2) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VLAN type." + ::= { qryVidStatusEntry 1 } + + + igmpVersion OBJECT-TYPE + SYNTAX INTEGER { + v2(1), + v3(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Setting IGMP version." + ::= { multicast 7 } +---------------------------------------- +-- port +---------------------------------------- +-- subrPortTable ::= { port 1 } +-- adslPort OBJECT IDENTIFIER ::= { port 2 } + shdslPort OBJECT IDENTIFIER ::= { port 3 } + pvc OBJECT IDENTIFIER ::= { port 4 } + ppvc OBJECT IDENTIFIER ::= { port 5 } + portOperation OBJECT IDENTIFIER ::= { port 6 } +-- pvcStats OBJECT IDENTIFIER ::= { port 7 } + rpvc OBJECT IDENTIFIER ::= { port 8 } +-- dsBcastDisableTable ::= { port 9 } + paepvc OBJECT IDENTIFIER ::= { port 10 } + tlspvc OBJECT IDENTIFIER ::= { port 11 } + +-- G.bond start from 51 + gbond OBJECT IDENTIFIER ::= { port 51 } + +-- Subscriber Port Table + + subrPortTable OBJECT-TYPE + SYNTAX SEQUENCE OF SubrPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes subscriber attributes for the port." + ::= { port 1 } + + subrPortEntry OBJECT-TYPE + SYNTAX SubrPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in subrPortTable." + INDEX { ifIndex } + ::= { subrPortTable 1 } + + SubrPortEntry ::= + SEQUENCE { + subrPortName DisplayString, + subrPortTel DisplayString + } + + subrPortName OBJECT-TYPE + SYNTAX DisplayString (SIZE (0..31)) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Name of the subscriber." + ::= { subrPortEntry 1 } + + subrPortTel OBJECT-TYPE + SYNTAX DisplayString (SIZE (0..15)) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Telephone number of the subscriber." + ::= { subrPortEntry 2 } + +-------------------- +-- adslPort +-------------------- + +-- ADSL Line Table + +-- adslLineConfTable OBJECT-TYPE +-- SYNTAX SEQUENCE OF AdslLineConfEntry +-- MAX-ACCESS not-accessible +-- STATUS current +-- DESCRIPTION +-- "This table includes common attributes describing the ADSL line." +-- ::= { adslPort 1 } +-- +--adslLineConfEntry OBJECT-TYPE +-- SYNTAX AdslLineConfEntry +-- MAX-ACCESS not-accessible +-- STATUS current +-- DESCRIPTION +-- "An entry in adslLineConfTable." +-- INDEX { ifIndex } +-- ::= { adslLineConfTable 1 } +-- +-- AdslLineConfEntry ::= +-- SEQUENCE { +-- adslLineConfAdslMode INTEGER, +-- adslLineConfAnnexL INTEGER, +-- adslLineConfAnnexM INTEGER, +-- adslLineConfAnnexI INTEGER, +-- adslLineConfOptionMask INTEGER, +-- adslLineConfPowerMgmt INTEGER, +-- adslLineConfPowerMode INTEGER, +-- adslLineConfAturMaxTxPower INTEGER, +-- adslLineConfAtucMaxTxPower INTEGER, +-- adslLineConfMaxRxPower INTEGER, +-- adslLineConfAturCarrierMask OCTET STRING, +-- adslLineConfAtucCarrierMask0 OCTET STRING, +-- adslLineConfAtucCarrierMask1 OCTET STRING, +-- adslLineConfAturInp INTEGER, +-- adslLineConfAtucInp INTEGER, +-- adslLineConfL0Time INTEGER, +-- adslLineConfL2Time INTEGER, +-- adslLineConfL2ATPR INTEGER, +-- adslLineConfL2ATPRT INTEGER, +-- adslLineConfMaxL2Rate INTEGER, +-- adslLineConfMinL2Rate INTEGER, +-- adslLineConfL0toL2Rate INTEGER +-- } +-- +-- adslLineConfAdslMode OBJECT-TYPE +-- SYNTAX INTEGER { +-- gDotLite(1), +-- gDotDmt(2), +-- t1Dot413(3), +-- auto(4), +-- etsi(5), +-- adsl2(6), +-- adsl2Plus(7) +-- } +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "G.lite and T1.413 are only applicable to annex A board. +-- ETSI is only applicable to annex B board." +-- ::= { adslLineConfEntry 1 } +-- +-- adslLineConfAnnexL OBJECT-TYPE +-- SYNTAX INTEGER { +-- enableNarrowMode(1), +-- enableWideMode(2), +-- disable(3) +-- } +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "Enable/disable annex L for the port(Only in AnnexA)." +-- ::= { adslLineConfEntry 2 } +-- +-- adslLineConfAnnexM OBJECT-TYPE +-- SYNTAX INTEGER { +-- enable(1), +-- disable(2) +-- } +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "Enable/disable annex M for the port(For BCM AnnexA solution)." +-- ::= { adslLineConfEntry 3 } +-- +-- adslLineConfAnnexI OBJECT-TYPE +-- SYNTAX INTEGER { +-- enable(1), +-- disable(2) +-- } +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "Enable/disable annex I for the port(For BCM AnnexA solution)." +-- ::= { adslLineConfEntry 4 } +-- +-- adslLineConfOptionMask OBJECT-TYPE +-- SYNTAX INTEGER +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The semantic for each bit is: +-- BIT 1 : Disable Trellis +-- BIT 2 : Disable Reed-Solomon +-- BIT 3 : Disable upstream bitswap +-- BIT 4 : Disable downstream bitswap +-- BIT 5 : Disable 1-bit constellation +-- BIT 6 : Disable transmit windowing +-- BIT 7 : Disable s=0.5 support (ADSL1 only) +-- BIT 8 : Disable G.lite rate limit (ADSL1 only)" +-- ::= { adslLineConfEntry 5 } +-- +-- adslLineConfPowerMgmt OBJECT-TYPE +-- SYNTAX INTEGER { +-- enableL2(1), +-- enableL2andL3(2), +-- disable(3) +-- } +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "Enable/disable power management for the port." +-- ::= { adslLineConfEntry 6 } +-- +-- adslLineConfPowerMode OBJECT-TYPE +-- SYNTAX INTEGER { +-- fix(1), +-- priorityToPower(2), +-- priorityToRate(3) +-- } +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The power mode of the ADSL line." +-- ::= { adslLineConfEntry 7 } +-- +-- adslLineConfAturMaxTxPower OBJECT-TYPE +-- SYNTAX INTEGER (-130..200) +-- UNITS "tenth dBm" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The maximum allowed transmit power of ATU-R." +-- ::= { adslLineConfEntry 8 } +-- +-- adslLineConfAtucMaxTxPower OBJECT-TYPE +-- SYNTAX INTEGER (-50..200) +-- UNITS "tenth dBm" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The maximum allowed transmit power of ATU-C." +-- ::= { adslLineConfEntry 9 } +-- +-- adslLineConfMaxRxPower OBJECT-TYPE +-- SYNTAX INTEGER (-255..255) +-- UNITS "tenth dBm" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The maximum aggregate received power." +-- ::= { adslLineConfEntry 10 } +-- +-- adslLineConfAturCarrierMask OBJECT-TYPE +-- SYNTAX OCTET STRING +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The upstream carrier mask. For CTLM AnnexA solution, bin is from 0 to 31; +-- CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. +-- Bit set to 1 indicates the bin is masked off." +-- ::= { adslLineConfEntry 11 } +-- +-- adslLineConfAtucCarrierMask0 OBJECT-TYPE +-- SYNTAX OCTET STRING +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The downstream carrier mask. For CTLM AnnexA solution, bin is from 32 to 255; +-- CTLM AnnexB solution, bin is from 64 to 255; BCM solution, bin is from 32 to 255. +-- Bit set to 1 indicates the bin is masked off." +-- ::= { adslLineConfEntry 12 } +-- +-- adslLineConfAtucCarrierMask1 OBJECT-TYPE +-- SYNTAX OCTET STRING +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates +-- the bin is masked off." +-- ::= { adslLineConfEntry 13 } +-- +-- adslLineConfAturInp OBJECT-TYPE +-- SYNTAX INTEGER { +-- zero(1), +-- zero-point-five(2), +-- one(3), +-- two(4), +-- four(5), +-- eight(6), +-- sixteen(7) +-- } +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. +-- For CTLM solution, user can set value from 1 ~ 4, +-- but for BCM solution, user can set value from 1 ~ 7." +-- ::= { adslLineConfEntry 14 } +-- +-- adslLineConfAtucInp OBJECT-TYPE +-- SYNTAX INTEGER { +-- zero(1), +-- zero-point-five(2), +-- one(3), +-- two(4), +-- four(5), +-- eight(6), +-- sixteen(7) +-- } +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. +-- For CTLM solution, user can set value from 1 ~ 4, +-- but for BCM solution, user can set value from 1 ~ 7." +-- ::= { adslLineConfEntry 15 } +-- +-- +-- adslLineConfL0Time OBJECT-TYPE +-- SYNTAX INTEGER +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "Set the minimum time in seconds that the ADSL line +-- must stay in L0 power mode before changing to the L2 power mode. +-- For CTLM solution, the range is 120 ~ 65535; +-- for BCM solution, the range is 10 ~ 65535." +-- ::= { adslLineConfEntry 16 } +-- +-- adslLineConfL2Time OBJECT-TYPE +-- SYNTAX INTEGER +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "Set minimum time in seconds that the ADSL line must stay in the +-- L2 power mode before reducing the power again in the L2 power mode. +-- For CTLM solution, the range is 60 ~ 65535; +-- for BCM solution, the range is 10 ~ 65535." +-- ::= { adslLineConfEntry 17 } +-- +-- adslLineConfL2ATPR OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "dB" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "Set the maximum Aggregate Transmit Power Reduction (ATPR) +-- in decibels (dB) that is permitted in a L2 power reduction. +-- The system can gradually decrease the ADSL line transmission power +-- while it is in the L2 power mode. This is the largest individual +-- power reduction allowed in the L2 power mode. +-- For CTLM solution, the range is 1 ~ 5(dB); +-- for BCM solution, the range is 0 ~ 15(dB)." +-- ::= { adslLineConfEntry 18 } +-- +-- adslLineConfL2ATPRT OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "dB" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "the maximum Aggregate Transmit Power Reduction Total (ATPRT) +-- in decibels (dB) that is permitted in the L2 power mode. +-- This is the total transmit power decrease that is allowed +-- to occur in the L2 power mode. +-- For CTLM solution, the range is 1 ~ 40(dB); +-- for BCM solution, the range is 0 ~ 15(dB)." +-- ::= { adslLineConfEntry 19 } +-- +-- +-- adslLineConfMaxL2Rate OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "kbps" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "configured maximum L2 rate. +-- (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)" +-- ::= { adslLineConfEntry 20 } +-- +-- adslLineConfMinL2Rate OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "kbps" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "configured minimum L2 rate. +-- (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)" +-- ::= { adslLineConfEntry 21 } +-- +-- adslLineConfL0toL2Rate OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "kbps" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "configured transition L0 to L2 rate. +-- (<=minl2rate/2 and >= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)" +-- ::= { adslLineConfEntry 22 } + +-- ADSL Port Batch Set + +--adslPortBatchSet OBJECT IDENTIFIER ::= { adslPort 3 } +-- +-- adslPortTarget OBJECT-TYPE +-- SYNTAX OCTET STRING +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The managed object is used for identify the target on which +-- the port configuration should be performed. The target is encoded as: +-- Byte 1: 0, Reserved(chaises) +-- Byte 2~3: 0,0 Reserved(slot) +-- Byte 4: 0, reserved +-- Byte 5~11:each octet specifies a set of eight ports, with the first +-- octet specifying ports 1 through 8, etc." +-- ::= { adslPortBatchSet 1 } +-- +-- adslPortOps OBJECT-TYPE +-- SYNTAX INTEGER +-- ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The managed object is for ADSL line configuration. When the EMS +-- wants to issue the desired operation, the EMS shall send SNMP-SET message to set +-- the corresponding bit value to be 1. The various bit positions are: +-- BIT 1: enable port +-- BIT 2: disable port +-- BIT 3: set ADSL mode +-- BIT 4: set line profile +-- BIT 5: set alarm profile +-- BIT 6: enable Annex L to be narrow mode(Only in AnnexA) +-- BIT 7: enable Annex L to be wide mode(Only in AnnexA) +-- BIT 8: disable Annex L(Only in AnnexA) +-- BIT 9: enable Annex M (For BCM AnnexA solution) +-- BIT 10: disable Annex M (For BCM AnnexA solution) +-- BIT 11: enable Annex I (For BCM AnnexA solution) +-- BIT 12: disable Annex I (For BCM AnnexA solution) +-- BIT 13: set option mask +-- BIT 14: enable power management mode to be L2 +-- BIT 15: enable power management mode to be L3 +-- BIT 16: disable power management mode +-- BIT 17: set power mode to be fixed +-- BIT 18: set power mode to be priority to power +-- BIT 19: set power mode to be priority to rate +-- BIT 20: set ATU-R max Tx power +-- BIT 21: set ATU-C max Tx power +-- BIT 22: set max Rx power +-- BIT 23: set ATU-R carrier mask +-- BIT 24: set ATU-C carrier mask +-- BIT 25: set ATU-R INP minimum setting +-- BIT 26: set ATU-C INP minimum setting" +-- ::= { adslPortBatchSet 2 } +-- +-- adslPortOps2 OBJECT-TYPE +-- SYNTAX INTEGER +-- ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The managed object is for ADSL line configuration. When the EMS +-- wants to issue the desired operation, the EMS shall send SNMP-SET message to set +-- the corresponding bit value to be 1. The various bit positions are: +-- BIT 1: set L0 Time +-- BIT 2: set L2 Time +-- BIT 3: set L2 ATPR +-- BIT 4: set L2 ATPRT +-- BIT 5: set maximum L2 rate +-- BIT 6: set minimum L2 rate +-- BIT 7: set transition L0 to L2 rate" +-- ::= { adslPortBatchSet 3 } +-- +-- +-- adslModeForBatchSet OBJECT-TYPE +-- SYNTAX INTEGER { +-- gDotLite(1), +-- gDotDmt(2), +-- t1Dot413(3), +-- auto(4), +-- etsi(5), +-- adsl2(6), +-- adsl2Plus(7) +-- } +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "G.lite and T1.413 are only applicable to annex A board. +-- ETSI is only applicable to annex B board." +-- ::= { adslPortBatchSet 4 } +-- +-- adslLineProfileForBatchSet OBJECT-TYPE +-- SYNTAX DisplayString (SIZE (1..31)) +-- ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The ADSL line profile." +-- ::= { adslPortBatchSet 5 } +-- +-- adslAlarmProfileForBatchSet OBJECT-TYPE +-- SYNTAX DisplayString (SIZE (1..31)) +-- ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The ADSL alarm profile." +-- ::= { adslPortBatchSet 6 } +-- +-- adslOptionMaskForBatchSet OBJECT-TYPE +-- SYNTAX INTEGER +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The semantic for each bit is identical to the object adslLineConfOptionMask." +-- ::= { adslPortBatchSet 7 } +-- +-- adslAturMaxTxPowerForBatchSet OBJECT-TYPE +-- SYNTAX INTEGER (-130..200) +-- UNITS "tenth dBm" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The maximum allowed transmit power of ATU-R." +-- ::= { adslPortBatchSet 8 } +-- +-- adslAtucMaxTxPowerForBatchSet OBJECT-TYPE +-- SYNTAX INTEGER (-50..200) +-- UNITS "tenth dBm" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The maximum allowed transmit power of ATU-C." +-- ::= { adslPortBatchSet 9 } +-- +-- adslMaxRxPowerForBatchSet OBJECT-TYPE +-- SYNTAX INTEGER (-255..255) +-- UNITS "tenth dBm" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The maximum aggregate received power." +-- ::= { adslPortBatchSet 10 } +-- +-- adslAturCarrierMaskForBatchSet OBJECT-TYPE +-- SYNTAX OCTET STRING +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The upstream carrier mask.For CTLM AnnexA solution, bin is from 0 to 31; +-- CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. +-- Bit set to 1 indicates the bin is masked off." +-- ::= { adslPortBatchSet 11 } +-- +-- adslAtucCarrierMask0ForBatchSet OBJECT-TYPE +-- SYNTAX OCTET STRING +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The downstream carrier mask from bin 32 to 255. Bit set to 1 indicates +-- the bin is masked off." +-- ::= { adslPortBatchSet 12 } +-- +-- adslAtucCarrierMask1ForBatchSet OBJECT-TYPE +-- SYNTAX OCTET STRING +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates +-- the bin is masked off." +-- ::= { adslPortBatchSet 13 } +-- +-- adslAturInpForBatchSet OBJECT-TYPE +-- SYNTAX INTEGER { +-- zero(1), +-- zero-point-five(2), +-- one(3), +-- two(4), +-- four(5), +-- eight(6), +-- sixteen(7) +-- } +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. +-- For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7." +-- ::= { adslPortBatchSet 14 } +-- +-- adslAtucInpForBatchSet OBJECT-TYPE +-- SYNTAX INTEGER { +-- zero(1), +-- zero-point-five(2), +-- one(3), +-- two(4), +-- four(5), +-- eight(6), +-- sixteen(7) +-- } +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. +-- For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7." +-- ::= { adslPortBatchSet 15 } +-- +-- +-- adslL0TimeForBatchSet OBJECT-TYPE +-- SYNTAX INTEGER +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "Set the minimum time in seconds that the ADSL line +-- must stay in L0 power mode before changing to the L2 power mode. +-- For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535." +-- ::= { adslPortBatchSet 16 } +-- +-- adslL2TimeForBatchSet OBJECT-TYPE +-- SYNTAX INTEGER +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "Set minimum time in seconds that the ADSL line +-- must stay in the L2 power mode before reducing the power +-- again in the L2 power mode. +-- For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535." +-- ::= { adslPortBatchSet 17 } +-- +-- adslL2ATPRForBatchSet OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "dB" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "Set the maximum Aggregate Transmit Power Reduction (ATPR) +-- in decibels (dB) that is permitted in a L2 power reduction. +-- The system can gradually decrease the ADSL line transmission power +-- while it is in the L2 power mode. This is the largest individual +-- power reduction allowed in the L2 power mode. +-- For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB)." +-- ::= { adslPortBatchSet 18 } +-- +-- adslL2ATPRTForBatchSet OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "dB" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "the maximum Aggregate Transmit Power Reduction Total (ATPRT) +-- in decibels (dB) that is permitted in the L2 power mode. +-- This is the total transmit power decrease that is allowed +-- to occur in the L2 power mode. +-- For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB)." +-- ::= { adslPortBatchSet 19 } +-- +-- adslMaxL2RateForBatchSet OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "kbps" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "configured maximum L2 rate. +-- (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)" +-- ::= { adslPortBatchSet 20 } +-- +-- adslMinL2RateForBatchSet OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "kbps" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "configured minimum L2 rate. +-- (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)" +-- ::= { adslPortBatchSet 21 } +-- +-- adslL0toL2RateForBatchSet OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "kbps" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "configured transition L0 to L2 rate. +-- (<=minl2rate/2 and >= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)" +-- ::= { adslPortBatchSet 22 } + +-- Line Status + +-- adslLineStatusTable OBJECT-TYPE +-- SYNTAX SEQUENCE OF AdslLineStatusEntry +-- MAX-ACCESS not-accessible +-- STATUS current +-- DESCRIPTION +-- "This table includes the ADSL line status." +-- ::= { adslPort 4 } +-- +--adslLineStatusEntry OBJECT-TYPE +-- SYNTAX AdslLineStatusEntry +-- MAX-ACCESS not-accessible +-- STATUS current +-- DESCRIPTION +-- "An entry in adslLineStatusTable." +-- INDEX { ifIndex } +-- ::= { adslLineStatusTable 1 } +-- +-- AdslLineStatusEntry ::= +-- SEQUENCE { +-- adslLineStatusMode INTEGER, +-- adslLineUpTime INTEGER +-- } +-- +-- adslLineStatusMode OBJECT-TYPE +-- SYNTAX INTEGER { +-- gDotLite(1), +-- gDotDmt(2), +-- t1Dot413(3), +-- etsi(4), +-- adsl2(5), +-- adsl2Plus(6), +-- none(7) +-- } +-- MAX-ACCESS read-only +-- STATUS current +-- DESCRIPTION +-- "The link up mode of the ADSL line." +-- ::= { adslLineStatusEntry 1 } +-- +-- adslLineUpTime OBJECT-TYPE +-- SYNTAX INTEGER +-- MAX-ACCESS read-only +-- STATUS current +-- DESCRIPTION +-- "The link up time of the ADSL line, in unit of seconds" +-- ::= { adslLineStatusEntry 2 } + +-- Power Mgmt Parameter Table + +-- powerMgmtParamTable OBJECT-TYPE +-- SYNTAX SEQUENCE OF PowerMgmtParamEntry +-- MAX-ACCESS not-accessible +-- STATUS current +-- DESCRIPTION +-- "This table defines L0 to L2 power transition parameters." +-- ::= { adslPort 5 } +-- +--powerMgmtParamEntry OBJECT-TYPE +-- SYNTAX PowerMgmtParamEntry +-- MAX-ACCESS not-accessible +-- STATUS current +-- DESCRIPTION +-- "An entry in powerMgmtParamTable." +-- INDEX { ifIndex } +-- ::= { powerMgmtParamTable 1 } +-- +-- PowerMgmtParamEntry ::= +-- SEQUENCE { +-- powerMgmtL0Time INTEGER, +-- powerMgmtL2Time INTEGER, +-- powerMgmtL2Atpr INTEGER, +-- powerMgmtL2Atprt INTEGER, +-- powerMgmtL2MinRate INTEGER, +-- powerMgmtL2MaxRate INTEGER, +-- powerMgmtL2ThreshRate INTEGER +-- } +-- +-- powerMgmtL0Time OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "second" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The object specifies the minimum time in L0 mode before L2 mode may be entered." +-- ::= { powerMgmtParamEntry 1 } +-- +--powerMgmtL2Time OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "second" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The object specifies the minimum time in L2 mode before trimming and in between power trims." +-- ::= { powerMgmtParamEntry 2 } +-- +-- powerMgmtL2Atpr OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "dB" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The maximum Aggregate Transmit Power Reduction." +-- ::= { powerMgmtParamEntry 3 } +-- +-- powerMgmtL2Atprt OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "dB" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The maximum Aggregate Transmit Power Reduction Total." +-- ::= { powerMgmtParamEntry 4 } +-- +-- powerMgmtL2MinRate OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "Kbps" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The object specifies the minimum L2 rate." +-- ::= { powerMgmtParamEntry 5 } +-- +-- powerMgmtL2MaxRate OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "Kbps" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The object specifies the maximum L2 rate." +-- ::= { powerMgmtParamEntry 6 } +-- +-- powerMgmtL2ThreshRate OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "Kbps" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The object specifies the rate threshold that triggers the line entering L0 or L2 mode." +-- ::= { powerMgmtParamEntry 7 } + +-- Power Mgmt PSD Table +-- Not support in 7324 RU R4.0.2 +-- powerMgmtPSDTable OBJECT-TYPE +-- SYNTAX SEQUENCE OF PowerMgmtPSDEntry +-- MAX-ACCESS not-accessible +-- STATUS current +-- DESCRIPTION +-- "This table provides the PSD setting for both ATU-C and ATU-R." +-- ::= { adslPort 6 } +-- +--powerMgmtPSDEntry OBJECT-TYPE +-- SYNTAX PowerMgmtPSDEntry +-- MAX-ACCESS not-accessible +-- STATUS current +-- DESCRIPTION +-- "An entry in powerMgmtPSDTable." +-- INDEX { ifIndex } +-- ::= { powerMgmtPSDTable 1 } +-- +-- PowerMgmtPSDEntry ::= +-- SEQUENCE { +-- powerMgmtAtucMaxPSD INTEGER, +-- powerMgmtAturMaxPSD INTEGER +-- } +-- +-- powerMgmtAtucMaxPSD OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "0.1dBm/Hz" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The object specifies the maximum ATU-C PSD." +-- ::= { powerMgmtPSDEntry 1 } +-- +-- powerMgmtAturMaxPSD OBJECT-TYPE +-- SYNTAX INTEGER +-- UNITS "0.1dBm/Hz" +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The object specifies the maximum ATU-R PSD." +-- ::= { powerMgmtPSDEntry 2 } + + +-------------------- +-- shdslPort +-------------------- + +-- SHDSL Line Table + + shdslLineConfTable OBJECT-TYPE + SYNTAX SEQUENCE OF ShdslLineConfEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes common attributes describing the SHDSL line." + ::= { shdslPort 1 } + + shdslLineConfEntry OBJECT-TYPE + SYNTAX ShdslLineConfEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in shdslLineConfTable." + INDEX { ifIndex } + ::= { shdslLineConfTable 1 } + + ShdslLineConfEntry ::= + SEQUENCE { + shdslLineConfShdslMode INTEGER, + shdslLineConfPmms INTEGER, + shdslLineConfPboMode INTEGER, + shdslLineConfPboValue INTEGER, + shdslLineConfShdslTCMode INTEGER + } + + shdslLineConfShdslMode OBJECT-TYPE + SYNTAX INTEGER { + stuc(1), + stur(2), + auto(3), + pam16(4), + pam32(5) + + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Mode of the SHDSL port." + ::= { shdslLineConfEntry 1 } + + shdslLineConfPmms OBJECT-TYPE + SYNTAX INTEGER { + normal(1), + forced(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Negotiated noise margin mode of the SHDSL port." + ::= { shdslLineConfEntry 2 } + + shdslLineConfPboMode OBJECT-TYPE + SYNTAX INTEGER { + normalepl(1), + forcedepl(2), + forcednoepl(3) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Power backoff mode of the SHDSL port." + ::= { shdslLineConfEntry 3 } + + shdslLineConfPboValue OBJECT-TYPE + SYNTAX INTEGER (0..31) + UNITS "dB" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Power backoff value of the SHDSL port." + ::= { shdslLineConfEntry 4 } + + shdslLineConfShdslTCMode OBJECT-TYPE + SYNTAX INTEGER { + atm(1), + efm(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Transmission Convergence Mode of the SHDSL port." + ::= { shdslLineConfEntry 5 } + +-- SHDSL Port Batch Set + + shdslPortBatchSet OBJECT IDENTIFIER ::= { shdslPort 2 } + + shdslPortTarget OBJECT-TYPE + SYNTAX OCTET STRING + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The managed object is used for identify the target on which + the port configuration should be performed. The target is encoded as: + Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 + Byte 2~3: each octet specifies a set of eight slots, with the + first octet specifying slots 1 through 8 and the second + octet specifying slots 9 through 16. + Byte 4: reserved + Byte 5~11:each octet specifies a set of eight ports, with the first + octet specifying ports 1 through 8, etc." + ::= { shdslPortBatchSet 1 } + + shdslPortOps OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-write + STATUS current + DESCRIPTION + "The managed object is for SHDSL line configuration. When the EMS + wants to issue the desired operation, the EMS shall send SNMP-SET message to set + the corresponding bit value to be 1. The various bit positions are: + BIT 1: enable port + BIT 2: disable port + BIT 3: set SHDSL mode + BIT 4: set line profile + BIT 5: set alarm profile + BIT 6: set pmms mode to be normal + BIT 7: set pmms mode to be forced + BIT 8: set pbo mode to be normalepl + BIT 9: set pbo mode to be forcedepl + BIT 10: set pbo mode to be forcednoepl + BIT 11: set pbo value" + ::= { shdslPortBatchSet 2 } + + shdslModeForBatchSet OBJECT-TYPE + SYNTAX INTEGER { + stuc(1), + stur(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Mode of the SHDSL port." + ::= { shdslPortBatchSet 3 } + + shdslLineProfileForBatchSet OBJECT-TYPE + SYNTAX DisplayString (SIZE (1..31)) + ACCESS read-write + STATUS current + DESCRIPTION + "The SHDSL line profile." + ::= { shdslPortBatchSet 4 } + + shdslAlarmProfileForBatchSet OBJECT-TYPE + SYNTAX DisplayString (SIZE (1..31)) + ACCESS read-write + STATUS current + DESCRIPTION + "The SHDSL alarm profile." + ::= { shdslPortBatchSet 5 } + + shdslPboValueForBatchSet OBJECT-TYPE + SYNTAX INTEGER (0..31) + UNITS "dB" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Power backoff value of the SHDSL port." + ::= { shdslPortBatchSet 6 } + + +-------------------- +-- pvc +-------------------- + + maxNumOfPvcs OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The maximum number of PVCs which could be created on a port." + ::= { pvc 1 } + +-- PVC Table + + pvcTable OBJECT-TYPE + SYNTAX SEQUENCE OF PvcEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes PVC configuration." + ::= { pvc 2 } + + pvcEntry OBJECT-TYPE + SYNTAX PvcEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in pvcTable." + INDEX { ifIndex, pvcVpi, pvcVci, pvcPvid } + ::= { pvcTable 1 } + + PvcEntry ::= + SEQUENCE { + pvcVpi INTEGER, + pvcVci INTEGER, + pvcPvid VlanIndex, + pvcPriority INTEGER, + pvcProfileDS DisplayString, + pvcRowStatus RowStatus, + pvcProfileUS DisplayString + } + + pvcVpi OBJECT-TYPE + SYNTAX INTEGER (0..255) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VPI of the pvc." + ::= { pvcEntry 1 } + + pvcVci OBJECT-TYPE + SYNTAX INTEGER (1..65535) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VCI of the pvc." + ::= { pvcEntry 2 } + + pvcPvid OBJECT-TYPE + SYNTAX VlanIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Default VID of the pvc." + ::= { pvcEntry 3 } + + + pvcPriority OBJECT-TYPE + SYNTAX INTEGER (0..7) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "802.1p default priority of the pvc." + ::= { pvcEntry 5 } + + pvcProfileDS OBJECT-TYPE + SYNTAX DisplayString (SIZE (1..31)) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side." + ::= { pvcEntry 6 } + + pvcRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object is used to create a new row or delete an existing row in this table." + ::= { pvcEntry 7 } + + pvcProfileUS OBJECT-TYPE + SYNTAX DisplayString (SIZE (1..31)) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side." + ::= { pvcEntry 8 } + +-- Upstream Rate Limit Table + + pvcUsRateLimitTable OBJECT-TYPE + SYNTAX SEQUENCE OF PvcUsRateLimitEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table defines the upstream rate limit for each PVC." + ::= { pvc 4 } + + pvcUsRateLimitEntry OBJECT-TYPE + SYNTAX PvcUsRateLimitEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in pvcUsRateLimitTable." + INDEX { ifIndex, pvcVpi, pvcVci } + ::= { pvcUsRateLimitTable 1 } + + PvcUsRateLimitEntry ::= + SEQUENCE { + pvcUsRateLimitEnable INTEGER, + pvcUsRateLimit INTEGER + } + + pvcUsRateLimitEnable OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Enable/disable upstream rate limit for a PVC." + ::= { pvcUsRateLimitEntry 1 } + + pvcUsRateLimit OBJECT-TYPE + SYNTAX INTEGER + UNITS "Kbps" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Upstream rate limit in Kbps for a PVC." + ::= { pvcUsRateLimitEntry 2 } + + +-------------------- +-- priority pvc +-------------------- + + maxNumOfPriorityPvcs OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The maximum number of priority PVCs which could be created on a port." + ::= { ppvc 1 } + +-- Priority PVC Table + + ppvcTable OBJECT-TYPE + SYNTAX SEQUENCE OF PpvcEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes priority PVC configuration." + ::= { ppvc 2 } + + ppvcEntry OBJECT-TYPE + SYNTAX PpvcEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in ppvcTable." + INDEX { ifIndex, ppvcVpi, ppvcVci, ppvcPvid } + ::= { ppvcTable 1 } + + PpvcEntry ::= + SEQUENCE { + ppvcVpi INTEGER, + ppvcVci INTEGER, + ppvcPvid VlanIndex, + ppvcEncap INTEGER, + ppvcPriority INTEGER, + ppvcRowStatus RowStatus + } + + ppvcVpi OBJECT-TYPE + SYNTAX INTEGER (0..255) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VPI of the ppvc." + ::= { ppvcEntry 1 } + + ppvcVci OBJECT-TYPE + SYNTAX INTEGER (1..65535) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VCI of the ppvc." + ::= { ppvcEntry 2 } + + ppvcPvid OBJECT-TYPE + SYNTAX VlanIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Default VID of the ppvc." + ::= { ppvcEntry 3 } + + ppvcEncap OBJECT-TYPE + SYNTAX INTEGER { + llc(1), + vc(2) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Encapsulation of the ppvc." + ::= { ppvcEntry 4 } + + ppvcPriority OBJECT-TYPE + SYNTAX INTEGER (0..7) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "802.1p default priority of the ppvc." + ::= { ppvcEntry 5 } + + ppvcRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object is used to create a new row or delete an existing row in this table." + ::= { ppvcEntry 6 } + +-- Priority PVC Member Table + + ppvcMemberTable OBJECT-TYPE + SYNTAX SEQUENCE OF PpvcMemberEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes priority PVC member configuration." + ::= { ppvc 4 } + + ppvcMemberEntry OBJECT-TYPE + SYNTAX PpvcMemberEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in ppvcMemberTable." + INDEX { ifIndex, ppvcVpi, ppvcVci, ppvcMemberVpi, ppvcMemberVci, ppvcMemberPriority } + ::= { ppvcMemberTable 1 } + + PpvcMemberEntry ::= + SEQUENCE { + ppvcMemberVpi INTEGER, + ppvcMemberVci INTEGER, + ppvcMemberPriority INTEGER, + ppvcMemberProfileDS DisplayString, + ppvcMemberRowStatus RowStatus, + ppvcMemberProfileUS DisplayString + } + + ppvcMemberVpi OBJECT-TYPE + SYNTAX INTEGER (0..255) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VPI of the member ppvc." + ::= { ppvcMemberEntry 1 } + + ppvcMemberVci OBJECT-TYPE + SYNTAX INTEGER (1..65535) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VCI of the member ppvc." + ::= { ppvcMemberEntry 2 } + + ppvcMemberPriority OBJECT-TYPE + SYNTAX INTEGER (0..7) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "802.1p default priority of the member ppvc." + ::= { ppvcMemberEntry 3 } + + ppvcMemberProfileDS OBJECT-TYPE + SYNTAX DisplayString (SIZE (1..31)) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The profile of the member ppvc in DS side." + ::= { ppvcMemberEntry 4 } + + ppvcMemberRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object is used to create a new row or delete an existing row in this table." + ::= { ppvcMemberEntry 5 } + + ppvcMemberProfileUS OBJECT-TYPE + SYNTAX DisplayString (SIZE (1..31)) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The profile of the member ppvc in US side." + ::= { ppvcMemberEntry 6 } + +-------------------- +-- portOperation +-------------------- + + portTarget OBJECT-TYPE + SYNTAX OCTET STRING + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The managed object is used for identify the target on which + the port configuration should be performed. The target is encoded as: + Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 + Byte 2~3: each octet specifies a set of eight slots, with the + first octet specifying slots 1 through 8 and the second + octet specifying slots 9 through 16. + Byte 4: reserved + Byte 5~11:each octet specifies a set of eight ports, with the first + octet specifying ports 1 through 8, etc." + ::= { portOperation 1 } + + portOps OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-write + STATUS current + DESCRIPTION + "The managed object is for xDSL line configuration. When the EMS + wants to issue the desired operation, the EMS shall send SNMP-SET message to set + the corresponding bit value to be 1. The various bit positions are: + BIT 1: enable port + BIT 2: disable port" + ::= { portOperation 2 } + +-------------------- +-- paepvc +-------------------- + +-- PPPoAoE PVC Table + + paepvcTable OBJECT-TYPE + SYNTAX SEQUENCE OF PaePvcEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes PPPoAoE PVC configuration." + ::= { paepvc 1 } + + paepvcEntry OBJECT-TYPE + SYNTAX PaePvcEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of paepvcTable." + INDEX { ifIndex, paepvcVpi, paepvcVci, paepvcPvid } + ::= { paepvcTable 1 } + + PaePvcEntry ::= + SEQUENCE { + paepvcVpi INTEGER, + paepvcVci INTEGER, + paepvcPvid VlanIndex, + paepvcPriority INTEGER, + paepvcProfileDS DisplayString, + paepvcAcName DisplayString, + paepvcServiceName DisplayString, + paepvcHelloTime INTEGER, + paepvcRowStatus RowStatus, + paepvcProfileUS DisplayString + } + + paepvcVpi OBJECT-TYPE + SYNTAX INTEGER (0..255) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VPI of the pvc." + ::= { paepvcEntry 1 } + + paepvcVci OBJECT-TYPE + SYNTAX INTEGER (1..65535) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VCI of the pvc." + ::= { paepvcEntry 2 } + + paepvcPvid OBJECT-TYPE + SYNTAX VlanIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Default VID of the pvc." + ::= { paepvcEntry 3 } + + + paepvcPriority OBJECT-TYPE + SYNTAX INTEGER (0..7) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "802.1p default priority of the pvc." + ::= { paepvcEntry 5 } + + paepvcProfileDS OBJECT-TYPE + SYNTAX DisplayString (SIZE (1..31)) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side." + ::= { paepvcEntry 6 } + + paepvcAcName OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Access concentrator name." + ::= { paepvcEntry 7 } + + paepvcServiceName OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Service name." + ::= { paepvcEntry 8 } + + paepvcHelloTime OBJECT-TYPE + SYNTAX INTEGER + UNITS "second" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The system will close the PVC if there are not any LCP echo messages passed through + during the LCP hello time." + ::= { paepvcEntry 9 } + + paepvcRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object is used to create a new row or delete an existing row in this table." + ::= { paepvcEntry 10 } + + paepvcProfileUS OBJECT-TYPE + SYNTAX DisplayString (SIZE (1..31)) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side." + ::= { paepvcEntry 11 } + +-------------------- +-- tlspvc +-------------------- + +-- TLS PVC Table + + tlspvcTable OBJECT-TYPE + SYNTAX SEQUENCE OF TlsPvcEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes Transparent LAN Service (TLS) PVC configuration." + ::= { tlspvc 1 } + + tlspvcEntry OBJECT-TYPE + SYNTAX TlsPvcEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of tlspvcTable." + INDEX { ifIndex, tlspvcVpi, tlspvcVci, tlspvcSvid } + ::= { tlspvcTable 1 } + + TlsPvcEntry ::= + SEQUENCE { + tlspvcVpi INTEGER, + tlspvcVci INTEGER, + tlspvcSvid VlanIndex, + tlspvcSpriority INTEGER, + tlspvcProfileDS DisplayString, + tlspvcRowStatus RowStatus, + tlspvcProfileUS DisplayString + } + + tlspvcVpi OBJECT-TYPE + SYNTAX INTEGER (0..255) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VPI of the pvc." + ::= { tlspvcEntry 1 } + + tlspvcVci OBJECT-TYPE + SYNTAX INTEGER (1..65535) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VCI of the pvc." + ::= { tlspvcEntry 2 } + + tlspvcSvid OBJECT-TYPE + SYNTAX VlanIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "s-tag VLAN ID of the pvc." + ::= { tlspvcEntry 3 } + + + tlspvcSpriority OBJECT-TYPE + SYNTAX INTEGER (0..7) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "s-tag priority of the pvc." + ::= { tlspvcEntry 5 } + + tlspvcProfileDS OBJECT-TYPE + SYNTAX DisplayString (SIZE (1..31)) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side." + ::= { tlspvcEntry 6 } + + tlspvcRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object is used to create a new row or delete an existing row in this table." + ::= { tlspvcEntry 7 } + + tlspvcProfileUS OBJECT-TYPE + SYNTAX DisplayString (SIZE (1..31)) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side." + ::= { tlspvcEntry 8 } + +-------------------- +-- gbond +-------------------- + +-- gbondTable + + gbondGroupTable OBJECT-TYPE + SYNTAX SEQUENCE OF GbondGroupEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table containing the G.Bond configuration information for + each bonding group of the device." + ::= { gbond 1 } + + gbondGroupEntry OBJECT-TYPE + SYNTAX GbondGroupEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of gbondTable." + INDEX { gbondGroupName } + ::= { gbondGroupTable 1 } + + GbondGroupEntry ::= + SEQUENCE { + gbondGroupName OCTET STRING, + gbondGroupPorts OCTET STRING, + gbondGroupSid INTEGER, + gbondGroupUpRate Unsigned32, + gbondGroupDownRate Unsigned32, + gbondGroupRowStatus RowStatus + } + + gbondGroupName OBJECT-TYPE + SYNTAX OCTET STRING (SIZE (0..31)) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "An administratively assigned string, which may be used to identify bonding group." + ::= { gbondGroupEntry 1 } + + gbondGroupPorts OBJECT-TYPE + SYNTAX OCTET STRING + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The set of ports which are currently assigned to the + bonding group of specified group name. + Byte 1: Reserved(chassis) + Byte 2~3: Reserved(slot) + Byte 4: Reserved + Byte 5: Each bit in the octet specifies a port from MSB to LSB. + for example: 32(hex) = 50(dec) = 00110010(bin) means the + port 3, 4 and 7. + Byte 6~10:Reserved" + ::= { gbondGroupEntry 2 } + + gbondGroupSid OBJECT-TYPE + SYNTAX INTEGER { + sid8(1), + sid12(2) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object indicates the sequence index mode of the bonding group." + ::= { gbondGroupEntry 3 } + + gbondGroupUpRate OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The UP stream rate." + ::= { gbondGroupEntry 4 } + + gbondGroupDownRate OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The DOWN stream rate." + ::= { gbondGroupEntry 5 } + + gbondGroupRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object indicates the status of this entry." + ::= { gbondGroupEntry 6 } + + +--------------- +-- switch +---------------------------------------- + +-- enetport OBJECT IDENTIFIER ::= { switch 3 } +-- bandwidth OBJECT IDENTIFIER ::= { switch 4 } +-- qschedule OBJECT IDENTIFIER ::= { switch 5 } +-- dot3ad OBJECT IDENTIFIER ::= { switch 6 } +-- stp OBJECT IDENTIFIER ::= { switch 7 } +-- bcastCtrl OBJECT IDENTIFIER ::= { switch 8 } +-- portIsolation OBJECT IDENTIFIER ::= { switch 9 } + dscp OBJECT IDENTIFIER ::= { switch 10 } +-- mstp OBJECT IDENTIFIER ::= { switch 11 } + vlanIsolation OBJECT IDENTIFIER ::= { switch 12 } + enetMtu OBJECT IDENTIFIER ::= { switch 13 } +-- managementVLANId OBJECT-TYPE +-- SYNTAX VlanIndex +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The VLAN ID for management." +-- ::= { switch 1 } + +-- maxNumOfStaticVlans OBJECT-TYPE +-- SYNTAX INTEGER +-- MAX-ACCESS read-only +-- STATUS current +-- DESCRIPTION +-- "The maximum number of VLANs supported by the system." +-- ::= { switch 2 } +-------------------- +-- dscp +-------------------- + + dscpMappingTable OBJECT-TYPE + SYNTAX SEQUENCE OF DscpMappingEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The table contains DSCP mapping configuration for the adsl and ethernet ports." + ::= { dscp 1 } + + dscpMappingEntry OBJECT-TYPE + SYNTAX DscpMappingEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of dscpMappingTable." + INDEX { dscpSrcCodePoint } + ::= { dscpMappingTable 1 } + + DscpMappingEntry ::= + SEQUENCE { + dscpSrcCodePoint INTEGER, +-- dscpMapCodePoint INTEGER, + dscpMapPriority INTEGER + } + + dscpSrcCodePoint OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The DSCP source code point used for mapping." + ::= { dscpMappingEntry 1 } + +-- dscpMapCodePoint OBJECT-TYPE +-- SYNTAX INTEGER (0..63) +-- MAX-ACCESS read-write +-- STATUS current +-- DESCRIPTION +-- "The mapping code point that will replace the source code point in the incoming packet." +-- ::= { dscpMappingEntry 2 } + + dscpMapPriority OBJECT-TYPE + SYNTAX INTEGER (0..7) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The mapping p bits that will replace the source p bits in the incoming packet." + ::= { dscpMappingEntry 3 } + +--- pfchen + dscpPortTable OBJECT-TYPE + SYNTAX SEQUENCE OF DscpPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The table contains DSCP mapping configuration for the adsl and ethernet ports." + ::= { dscp 2 } + + dscpPortEntry OBJECT-TYPE + SYNTAX DscpPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of dscpPortTable." + INDEX { ifIndex } + ::= { dscpPortTable 1 } + + DscpPortEntry ::= + SEQUENCE { + dscpStatusEnable INTEGER + } + + dscpStatusEnable OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The DSCP port status." + ::= { dscpPortEntry 1 } + +-------------------- +-- Vlan Isolation +-------------------- + + vlanIsolationTable OBJECT-TYPE + SYNTAX SEQUENCE OF VlanIsolationEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table contains configuration of isolated VLAN." + ::= { vlanIsolation 1 } + + vlanIsolationEntry OBJECT-TYPE + SYNTAX VlanIsolationEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of vlanIsolationTable." + INDEX { dot1qVlanIndex } + ::= { vlanIsolationTable 1 } + + VlanIsolationEntry ::= + SEQUENCE { + vlanIsolationRowStatus INTEGER + } + + vlanIsolationRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Row status of the table used to create/delete an entry." + ::= { vlanIsolationEntry 1 } + +-------------------- +-- enet MTU +-------------------- + + enetMaxMtu OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Sets the maximum MTU size for layer 2 frame, size from 1526 to 1600, default value is 1526." + ::= { enetMtu 1 } + +---------------------------------------- +-- sys +---------------------------------------- + +-- sysState OBJECT IDENTIFIER ::= { sys 1 } +-- sysOperation OBJECT IDENTIFIER ::= { sys 2 } +-- hwMonitor OBJECT IDENTIFIER ::= { sys 3 } +-- timeSetup OBJECT IDENTIFIER ::= { sys 4 } + accessCtrl OBJECT IDENTIFIER ::= { sys 5 } +-- syslog OBJECT IDENTIFIER ::= { sys 6 } +-- snmp OBJECT IDENTIFIER ::= { sys 7 } + extAlarm OBJECT IDENTIFIER ::= { sys 8 } + user OBJECT IDENTIFIER ::= { sys 9 } + +---------------------------------------- +-- slot id +---------------------------------------- + sysSlotId OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Device slot ID(0...255)." + ::= { sys 10 } + +-------------------- +-- Access Control +-------------------- +-- Secured Client Table + + securedClientTable OBJECT-TYPE + SYNTAX SEQUENCE OF SecuredClientEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains information about secured clients." + ::= { accessCtrl 2 } + + securedClientEntry OBJECT-TYPE + SYNTAX SecuredClientEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A list of secured client entry." + INDEX { securedClientIndex } + ::= { securedClientTable 1 } + + SecuredClientEntry ::= + SEQUENCE { + securedClientIndex INTEGER, + securedClientStartIp IpAddress, + securedClientEndIp IpAddress, + securedClientService INTEGER, + securedClientEnable INTEGER + } + + securedClientIndex OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The index of the entry." + ::= { securedClientEntry 1 } + + securedClientStartIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The starting IP address of the secured client set." + ::= { securedClientEntry 2 } + + securedClientEndIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The ending IP address of the secured client set." + ::= { securedClientEntry 3 } + + securedClientService OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Each bit corresponds to a service. The bit is set to 1 if the + service is enabled, and set to 0 if the service is disabled. + The various bit positions are: + BIT 1: telnet + BIT 2: ftp + BIT 3: web + BIT 4: icmp + BIT 5: ssh + BIT 6: snmp." + ::= { securedClientEntry 4 } + + securedClientEnable OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Enable/disable the entry." + ::= { securedClientEntry 5 } + +---------------------------------------- +--extAlarm +---------------------------------------- + + extAlarmTable OBJECT-TYPE + SYNTAX SEQUENCE OF ExtAlarmEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains external alarm information." + ::= { extAlarm 1 } + + extAlarmEntry OBJECT-TYPE + SYNTAX ExtAlarmEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The entry of external alarm table." + INDEX { extAlarmIndex } + ::= { extAlarmTable 1 } + + ExtAlarmEntry ::= + SEQUENCE { + extAlarmIndex INTEGER, + extAlarmname OCTET STRING, + extAlarmstatus OCTET STRING + } + + extAlarmIndex OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The index of the entry." + ::= { extAlarmEntry 1 } + + extAlarmname OBJECT-TYPE + SYNTAX DisplayString (SIZE (1..31)) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The external alarm name." + ::= { extAlarmEntry 2 } + + extAlarmstatus OBJECT-TYPE + SYNTAX DisplayString (SIZE (1..31)) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Dispaly 'Normal' or 'Alarm' string" + ::= { extAlarmEntry 3 } + +-------------------- +-- User Management +-------------------- + + userAuthMode OBJECT-TYPE + SYNTAX INTEGER { + local(1), + radius(2), + localThenRadius(3) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "User authentication procsssing mode." + ::= { user 1 } + + userAuthServerIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The IP address of the authentication server." + ::= { user 2 } + + userAuthServerPort OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The port of the authentication server." + ::= { user 3 } + + userAuthServerSecret OBJECT-TYPE + SYNTAX OCTET STRING + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The secret between the authentication server and the NE for authentication process." + ::= { user 4 } + +-- userTable + + userTable OBJECT-TYPE + SYNTAX SEQUENCE OF UserEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains user information." + ::= { user 5 } + + userEntry OBJECT-TYPE + SYNTAX UserEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of userTable." + INDEX { userName } + ::= { userTable 1 } + + UserEntry ::= + SEQUENCE { + userName DisplayString, + userPassword DisplayString, + userPriviledge INTEGER, + userRowStatus RowStatus + } + + userName OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The user name." + ::= { userEntry 1 } + + userPassword OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The user password." + ::= { userEntry 2 } + + userPriviledge OBJECT-TYPE + SYNTAX INTEGER { + high(1), + middle(2), + low(3) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The user priviledge to decide what operation the user can and cannot do." + ::= { userEntry 3 } + + userRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The row status used to create or delete a user." + ::= { userEntry 4 } + + userAuthDefaultPriviledge OBJECT-TYPE + SYNTAX INTEGER { + high(1), + middle(2), + low(3), + deny(4) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The user default priviledge to be assigned when radius authentication succeds + but no user priviledge information(radius service-type) is provided." + ::= { user 6 } + + + stdioTimeout OBJECT-TYPE + SYNTAX INTEGER (0..360) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Set the stdio timeout, 0~360 minutes." + ::= { sys 12 } + +---------------------------------------- +-- statistics +---------------------------------------- + + dhcpStats OBJECT IDENTIFIER ::= { statistics 11 } + paepvcStats OBJECT IDENTIFIER ::= { statistics 12 } +-- igmpStats OBJECT IDENTIFIER ::= { statistics 2 } + macStats OBJECT IDENTIFIER ::= { statistics 13 } +-- adslStats OBJECT IDENTIFIER ::= { statistics 4 } + shdslStats OBJECT IDENTIFIER ::= { statistics 14 } +-- ipStats OBJECT IDENTIFIER ::= { statistics 6 } +-- mstpStats OBJECT IDENTIFIER ::= { statistics 7 } + gbondStats OBJECT IDENTIFIER ::= { statistics 51 } + +-------------------- +-- DHCP +-------------------- + +-- dhcpSnoopIpTable + + dhcpSnoopIpTable OBJECT-TYPE + SYNTAX SEQUENCE OF DhcpSnoopIpEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table shows the IP addresses and netmasks offered by the DHCP server." + ::= { dhcpStats 1 } + + dhcpSnoopIpEntry OBJECT-TYPE + SYNTAX DhcpSnoopIpEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of dhcpSnoopIpTable." + INDEX { ifIndex, dhcpSnoopIp } + ::= { dhcpSnoopIpTable 1 } + + DhcpSnoopIpEntry ::= + SEQUENCE { + dhcpSnoopIp IpAddress, + dhcpSnoopMac PhysAddress + } + + dhcpSnoopIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The snooped IP address." + ::= { dhcpSnoopIpEntry 1 } + + dhcpSnoopMac OBJECT-TYPE + SYNTAX PhysAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The snooped MAC address." + ::= { dhcpSnoopIpEntry 2 } + +-- dhcpSnoopCounterTable + + dhcpSnoopCounterTable OBJECT-TYPE + SYNTAX SEQUENCE OF DhcpSnoopCounterEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table shows the DHCP statistics." + ::= { dhcpStats 2 } + + dhcpSnoopCounterEntry OBJECT-TYPE + SYNTAX DhcpSnoopCounterEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of dhcpSnoopCounterTable." + INDEX { ifIndex } + ::= { dhcpSnoopCounterTable 1 } + + DhcpSnoopCounterEntry ::= + SEQUENCE { + dhcpDiscovery Counter64, + dhcpOffer Counter64, + dhcpRequest Counter64, + dhcpAck Counter64, + dhcpAckBySnoopFull Counter64 + } + + dhcpDiscovery OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of received DHCP server discovery packets." + ::= { dhcpSnoopCounterEntry 1 } + + dhcpOffer OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of received DHCP server offer packets." + ::= { dhcpSnoopCounterEntry 2 } + + dhcpRequest OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of received DHCP IP request packets." + ::= { dhcpSnoopCounterEntry 3 } + + dhcpAck OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of received DHCP IP acknowledge packets." + ::= { dhcpSnoopCounterEntry 4 } + + dhcpAckBySnoopFull OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of received DHCP IP acknowledge packets that replace the oldest snooping + entry in snooping table due to table full." + ::= { dhcpSnoopCounterEntry 5 } + + +-- paepvcSessionTable + + paepvcSessionTable OBJECT-TYPE + SYNTAX SEQUENCE OF PaepvcSessionEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table shows the paepvc session statistics." + ::= { paepvcStats 1 } + + paepvcSessionEntry OBJECT-TYPE + SYNTAX PaepvcSessionEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of paepvcSessionTable." + INDEX { ifIndex , paepvcSessionVpi, paepvcSessionVci } + ::= { paepvcSessionTable 1 } + + PaepvcSessionEntry ::= + SEQUENCE { + paepvcSessionVpi INTEGER, + paepvcSessionVci INTEGER, + paepvcSessionState INTEGER, + paepvcSessionId INTEGER, + paepvcSessionUptime Unsigned32, + paepvcSessionacname DisplayString, + paepvcSessionsrvcname DisplayString + } + + paepvcSessionVpi OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The PAEPVC VPI." + ::= { paepvcSessionEntry 1 } + + paepvcSessionVci OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The PAEPVC VCI." + ::= { paepvcSessionEntry 2 } + + paepvcSessionState OBJECT-TYPE + SYNTAX INTEGER { + down(1), + pppoe(2), + ppp(3), + up(4) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The PAEPVC status." + ::= { paepvcSessionEntry 3 } + + paepvcSessionId OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The PAEPVC session ID." + ::= { paepvcSessionEntry 4 } + + paepvcSessionUptime OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "second" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The PAEPVC session uptime." + ::= { paepvcSessionEntry 5 } + + paepvcSessionacname OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Access concentrator name." + ::= { paepvcSessionEntry 6 } + + paepvcSessionsrvcname OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Service name." + ::= { paepvcSessionEntry 7 } + + +-- paepvcCountTable + + paepvcCountTable OBJECT-TYPE + SYNTAX SEQUENCE OF PaepvcCountEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table shows the paepvc counters." + ::= { paepvcStats 2 } + + paepvcCountEntry OBJECT-TYPE + SYNTAX PaepvcCountEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of paepvcCountTable." + INDEX { ifIndex , paepvcCountVpi, paepvcCountVci } + ::= { paepvcCountTable 1 } + + PaepvcCountEntry ::= + SEQUENCE { + paepvcCountVpi INTEGER, + paepvcCountVci INTEGER, + paepvcCountPppLcpCfgReqRx Unsigned32, + paepvcCountPppLcpEchoReqRx Unsigned32, + paepvcCountPppLcpEchoReplyRx Unsigned32, + paepvcCountPadiTx Unsigned32, + paepvcCountPadoRx Unsigned32, + paepvcCountPadrTx Unsigned32, + paepvcCountPadsRx Unsigned32, + paepvcCountPadtTx Unsigned32, + paepvcCountPadtRx Unsigned32, + paepvcCountSrvcnameErrRx Unsigned32, + paepvcCountAcSystemErrRx Unsigned32, + paepvcCountGenericErrTx Unsigned32, + paepvcCountGenericErrRx Unsigned32 + } + + + paepvcCountVpi OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The PAEPVC VPI." + ::= { paepvcCountEntry 1 } + + paepvcCountVci OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The PAEPVC VCI." + ::= { paepvcCountEntry 2 } + + paepvcCountPppLcpCfgReqRx OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of ppp lcp config-request received." + ::= { paepvcCountEntry 3 } + + paepvcCountPppLcpEchoReqRx OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of ppp lcp echo-request received." + ::= { paepvcCountEntry 4 } + + paepvcCountPppLcpEchoReplyRx OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of ppp lcp echo-reply received." + ::= { paepvcCountEntry 5 } + + paepvcCountPadiTx OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of pppoe padi transfered" + ::= { paepvcCountEntry 6 } + + paepvcCountPadoRx OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of pppoe pado received" + ::= { paepvcCountEntry 7 } + + paepvcCountPadrTx OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of pppoe padr transfered" + ::= { paepvcCountEntry 8 } + + paepvcCountPadsRx OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of pppoe pads received" + ::= { paepvcCountEntry 9 } + + paepvcCountPadtTx OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of pppoe padt transfered" + ::= { paepvcCountEntry 10 } + + paepvcCountPadtRx OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of pppoe padt received" + ::= { paepvcCountEntry 11 } + + paepvcCountSrvcnameErrRx OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of pppoe service name error received" + ::= { paepvcCountEntry 12 } + + paepvcCountAcSystemErrRx OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of pppoe access concentrator name error received" + ::= { paepvcCountEntry 13 } + + paepvcCountGenericErrTx OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of pppoe generic error transfered" + ::= { paepvcCountEntry 14 } + + paepvcCountGenericErrRx OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of pppoe generic error received" + ::= { paepvcCountEntry 15 } + + +-------------------- +-- MAC +-------------------- + + macDisplayTarget OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This managed object is a filter used for identify the target from which + the MAC addresses are learned in macTable. The target could be: + 99: all ports in the system + 98: all subscriber ports + 97: all Ethernet ports + + IfIndex is used for identifying subscriber ports and Ethernet Ports(e.g. 1 ~ 50)." + ::= { macStats 1 } + +-- macTable + + macTable OBJECT-TYPE + SYNTAX SEQUENCE OF MacEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains information about unicast + entries for which the bridge has forwarding and/or + filtering information. This information is used + by the transparent bridging function in + determining how to propagate a received frame." + ::= { macStats 2 } + + macEntry OBJECT-TYPE + SYNTAX MacEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of macTable." + INDEX { macAddress } + ::= { macTable 1 } + + MacEntry ::= + SEQUENCE { + macAddress MacAddress, + macPort INTEGER, + macStatus INTEGER + } + + macAddress OBJECT-TYPE + SYNTAX MacAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A unicast MAC address for which the bridge has + forwarding and/or filtering information." + ::= { macEntry 1 } + + macPort OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The port from which the mac address has been learned." + ::= { macEntry 2 } + + macStatus OBJECT-TYPE + SYNTAX INTEGER { + other(1), + invalid(2), + learned(3), + self(4), + mgmt(5) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The status of this entry." + ::= { macEntry 3 } + + +-------------------- +-- SHDSL +-------------------- + +-- shdslLinePerfTable + + shdslLinePerfTable OBJECT-TYPE + SYNTAX SEQUENCE OF ShdslLinePerfEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The table displays SHDSL line performance." + ::= { shdslStats 1 } + + shdslLinePerfEntry OBJECT-TYPE + SYNTAX ShdslLinePerfEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of shdslLinePerfTable." + INDEX { ifIndex } + ::= { shdslLinePerfTable 1 } + + ShdslLinePerfEntry ::= + SEQUENCE { + shdslLinePerfEs Counter, + shdslLinePerfSes Counter, + shdslLinePerfCrc Counter, + shdslLinePerfLosws Counter, + shdslLinePerfUas Counter, + shdslLinePerfSegmentAnomalies Counter, + shdslLinePerfSegmentDefect Counter + } + + shdslLinePerfEs OBJECT-TYPE + SYNTAX Counter + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Count of Errored Seconds (ES) on this endpoint since link up." + ::= { shdslLinePerfEntry 1 } + + shdslLinePerfSes OBJECT-TYPE + SYNTAX Counter + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Count of Severely Errored Seconds (SES) on this endpoint since link up." + ::= { shdslLinePerfEntry 2 } + + shdslLinePerfCrc OBJECT-TYPE + SYNTAX Counter + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Count of CRC anomalies on this endpoint since link up." + ::= { shdslLinePerfEntry 3 } + + shdslLinePerfLosws OBJECT-TYPE + SYNTAX Counter + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Count of Loss of Sync Word (LOSW) Seconds on this endpoint since link up." + ::= { shdslLinePerfEntry 4 } + + shdslLinePerfUas OBJECT-TYPE + SYNTAX Counter + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Count of Unavailable Seconds (UAS) on this endpoint since link up." + ::= { shdslLinePerfEntry 5 } + + shdslLinePerfSegmentAnomalies OBJECT-TYPE + SYNTAX Counter + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Count of Segment Anomalies on this endpoint since link up." + ::= { shdslLinePerfEntry 6 } + + shdslLinePerfSegmentDefect OBJECT-TYPE + SYNTAX Counter + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Count of Segment Defects on this endpoint since link up." + ::= { shdslLinePerfEntry 7 } + +-------------------- +-- IGMP +-------------------- + + igmpQueryCntTotal OBJECT-TYPE + SYNTAX Counter + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of IGMP query messages received." + ::= { statistics 1 } + + igmpReportCntTotal OBJECT-TYPE + SYNTAX Counter + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of IGMP report messages received." + ::= { statistics 2 } + + igmpLeaveCntTotal OBJECT-TYPE + SYNTAX Counter + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of IGMP leave messages received." + ::= { statistics 3 } + + igmpNumOfActiveGroups OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of IGMP learned groups." + ::= { statistics 4 } + + + +-- igmp Group Table + igmpGroupTable OBJECT-TYPE + SYNTAX SEQUENCE OF IgmpGroupEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes igmp group information." + ::= { statistics 5 } + + igmpGroupEntry OBJECT-TYPE + SYNTAX IgmpGroupEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in igmpGroupTable." + INDEX { igmpGroupIp } + ::= { igmpGroupTable 1 } + + IgmpGroupEntry ::= + SEQUENCE { + igmpGroupIp IpAddress, + igmpGroupvid INTEGER, + igmpGroupnumberOfMembers INTEGER, + igmpGroupMemberPorts PortList + + } + + igmpGroupIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "igmp group IP" + ::= { igmpGroupEntry 1 } + + igmpGroupvid OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "vlan id" + ::= { igmpGroupEntry 2 } + + igmpGroupnumberOfMembers OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "number Of Members" + + ::= { igmpGroupEntry 3 } + + igmpGroupMemberPorts OBJECT-TYPE + SYNTAX PortList + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Group Member Ports" + + ::= { igmpGroupEntry 4 } + + + + +-- igmp Group port Entry + igmpGroupPortTable OBJECT-TYPE + SYNTAX SEQUENCE OF IgmpGroupPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes igmp Group port information." + ::= { statistics 6 } + + igmpGroupPortEntry OBJECT-TYPE + SYNTAX IgmpGroupPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in igmpGroupPortTable." + INDEX { ifIndex , igmpGroupPortIp , igmpGroupPortvid} + ::= { igmpGroupPortTable 1 } + + IgmpGroupPortEntry ::= + SEQUENCE { + igmpGroupPortIp IpAddress, + igmpGroupPortvid INTEGER + } + + igmpGroupPortIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Igmp Group IP" + ::= { igmpGroupPortEntry 1 } + + igmpGroupPortvid OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Igmp Group vid" + ::= { igmpGroupPortEntry 2 } + + +-- igmpGroupTableV2 + + igmpGroupTableV2 OBJECT-TYPE + SYNTAX SEQUENCE OF IgmpGroupEntryV2 + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that displays IGMP learned group member information." + ::= { statistics 7 } + + igmpGroupEntryV2 OBJECT-TYPE + SYNTAX IgmpGroupEntryV2 + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of igmpGroupTableV2." + INDEX { igmpGroupVid, igmpGroupIp } + ::= { igmpGroupTableV2 1 } + + IgmpGroupEntryV2 ::= + SEQUENCE { + igmpGroupVid VlanIndex, + igmpGroupIp IpAddress, + igmpGroupNumOfMembers INTEGER, + igmpGroupMemberPorts PortList + } + + igmpGroupVid OBJECT-TYPE + SYNTAX VlanIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The IGMP group VLAN ID." + ::= { igmpGroupEntryV2 1 } + + igmpGroupIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The multicast IP address." + ::= { igmpGroupEntryV2 2 } + + igmpGroupNumOfMembers OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of member ports in the group." + ::= { igmpGroupEntryV2 3 } + + igmpGroupMemberPorts OBJECT-TYPE + SYNTAX PortList + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The member port list of the group." + ::= { igmpGroupEntryV2 4 } + +-- igmpGroupPortTableV2 + + igmpGroupPortTableV2 OBJECT-TYPE + SYNTAX SEQUENCE OF IgmpGroupPortEntryV2 + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that displays IGMP joined groups in this port." + ::= { statistics 8 } + + igmpGroupPortEntryV2 OBJECT-TYPE + SYNTAX IgmpGroupPortEntryV2 + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of igmpGroupPortTableV2." + INDEX { ifIndex, igmpGroupPortVid, igmpGroupPortIp, igmpGroupPortSourceIp } + ::= { igmpGroupPortTableV2 1 } + + IgmpGroupPortEntryV2 ::= + SEQUENCE { + igmpGroupPortVid VlanIndex, + igmpGroupPortIp IpAddress, + igmpGroupPortSourceIp IpAddress + } + + igmpGroupPortVid OBJECT-TYPE + SYNTAX VlanIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The IGMP group VLAN ID." + ::= { igmpGroupPortEntryV2 1 } + + igmpGroupPortIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The multicast IP address." + ::= { igmpGroupPortEntryV2 2 } + + igmpGroupPortSourceIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The source IP address that joins the IGMP group." + ::= { igmpGroupPortEntryV2 3 } + + +-- igmpPortCtrlPduTable + + igmpPortCtrlPduTable OBJECT-TYPE + SYNTAX SEQUENCE OF IgmpPortCtrlPduEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that displays IGMP related counter values in this port." + ::= { statistics 9 } + + igmpPortCtrlPduEntry OBJECT-TYPE + SYNTAX IgmpPortCtrlPduEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of igmpPortCtrlPduTable." + INDEX { ifIndex } + ::= { igmpPortCtrlPduTable 1 } + + IgmpPortCtrlPduEntry ::= + SEQUENCE { + igmpPortCtrlPduQueryCnt Counter, + igmpPortCtrlPduReportCnt Counter, + igmpPortCtrlPduLeaveCnt Counter, + igmpPortNumOfActiveGroups INTEGER + } + + igmpPortCtrlPduQueryCnt OBJECT-TYPE + SYNTAX Counter + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of IGMP query messages received in this port." + ::= { igmpPortCtrlPduEntry 1 } + + igmpPortCtrlPduReportCnt OBJECT-TYPE + SYNTAX Counter + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of IGMP report messages received in this port." + ::= { igmpPortCtrlPduEntry 2 } + + igmpPortCtrlPduLeaveCnt OBJECT-TYPE + SYNTAX Counter + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of IGMP leave messages received in this port." + ::= { igmpPortCtrlPduEntry 3 } + + igmpPortNumOfActiveGroups OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of active IGMP groups in this port." + ::= { igmpPortCtrlPduEntry 4 } + +-------------------- +-- G.Bond State +-------------------- +-- gbondStateTable + + gbondStateTable OBJECT-TYPE + SYNTAX SEQUENCE OF GbondStateEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table containing the G.Bond configuration information for + each bonding group of the device." + ::= { gbondStats 1 } + + gbondStateEntry OBJECT-TYPE + SYNTAX GbondStateEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry of gbondTable." + INDEX { gbondStateName } + ::= { gbondStateTable 1 } + + GbondStateEntry ::= + SEQUENCE { + gbondStateName OCTET STRING, + gbondStateSid INTEGER, + gbondStateUpRate Unsigned32, + gbondStateDownRate Unsigned32, + gbondStateMember OCTET STRING, + gbondStatelinkup OCTET STRING, + gbondStateTx OCTET STRING, + gbondStateRx OCTET STRING, + gbondStatelinkdown OCTET STRING + } + + gbondStateName OBJECT-TYPE + SYNTAX OCTET STRING (SIZE (0..31)) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "An administratively assigned string, which identifies the bonding group." + ::= { gbondStateEntry 1 } + + gbondStateSid OBJECT-TYPE + SYNTAX INTEGER { + sid8(1), + sid12(2) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates the sequence index mode of the bonding group." + ::= { gbondStateEntry 2 } + + + gbondStateUpRate OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The current up stream rate." + ::= { gbondStateEntry 3 } + + gbondStateDownRate OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The current down stream rate." + ::= { gbondStateEntry 4 } + + gbondStateMember OBJECT-TYPE + SYNTAX OCTET STRING + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicate if the port is a member port of the bonding group. + The target is encoded + as: + Byte 1: the octet specifies a set of eight Chassis, Chassis 0 through 7 + Byte 2~3: each octet specifies a set of eight slots, with the + first octet specifying slots 1 through 8 and the second + octet specifying slots 9 through 16. + Byte 4: reserved + Byte 5: Each bit in the octet specifies a port from MSB to LSB. + for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7." + ::= { gbondStateEntry 5 } + + gbondStatelinkup OBJECT-TYPE + SYNTAX OCTET STRING + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicate if the link status of port is bidirectional. + The target is encoded + as: + Byte 1: the octet specifies a set of eight Chassis, Chassis 0 through 7 + Byte 2~3: each octet specifies a set of eight slots, with the + first octet specifying slots 1 through 8 and the second + octet specifying slots 9 through 16. + Byte 4: reserved + Byte 5: Each bit in the octet specifies a port from MSB to LSB. + for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7." + ::= { gbondStateEntry 6 } + + gbondStateTx OBJECT-TYPE + SYNTAX OCTET STRING + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicate if the link status of port is Tx only. + The target is encoded + as: + Byte 1: the octet specifies a set of eight Chassis, Chassis 0 through 7 + Byte 2~3: each octet specifies a set of eight slots, with the + first octet specifying slots 1 through 8 and the second + octet specifying slots 9 through 16. + Byte 4: reserved + Byte 5: Each bit in the octet specifies a port from MSB to LSB. + for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7." + ::= { gbondStateEntry 7 } + + gbondStateRx OBJECT-TYPE + SYNTAX OCTET STRING + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicate if the link status of port is Rx only. + The target is encoded + as: + Byte 1: the octet specifies a set of eight Chassis, Chassis 0 through 7 + Byte 2~3: each octet specifies a set of eight slots, with the + first octet specifying slots 1 through 8 and the second + octet specifying slots 9 through 16. + Byte 4: reserved + Byte 5: Each bit in the octet specifies a port from MSB to LSB. + for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7." + ::= { gbondStateEntry 8 } + + gbondStatelinkdown OBJECT-TYPE + SYNTAX OCTET STRING + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicate if the link status of the port is down. + The target is encoded + as: + Byte 1: the octet specifies a set of eight Chassis, Chassis 0 through 7 + Byte 2~3: each octet specifies a set of eight slots, with the + first octet specifying slots 1 through 8 and the second + octet specifying slots 9 through 16. + Byte 4: reserved + Byte 5: Each bit in the octet specifies a port from MSB to LSB. + for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7." + ::= { gbondStateEntry 9 } + + +---------------------------------------- +-- clear +---------------------------------------- + + counterClearTarget OBJECT-TYPE + SYNTAX OCTET STRING + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This managed object is used for identify the target on which + the counter would be cleared. The target is encoded as: + Byte 1: reserved + Byte 2~3: reserved + Byte 4: reserved + Byte 5~11:each octet specifies a set of eight ports, with the first + octet specifying ports 1 through 8, etc." + ::= { clear 1 } + + counterClearOps OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The corresponding bit is set to 1 to start the operation. + The various bit positions are: + BIT 1: clear interface counters + BIT 2: clear pvc packet counters + BIT 3: clear port ATM counters + BIT 4: clear pvc ATM counters + BIT 5: clear DHCP counters + BIT 6: clear IGMP counters + BIT 7: clear IGMP port counters" + ::= { clear 2 } + + counterClearVpi OBJECT-TYPE + SYNTAX INTEGER (0..255) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "VPI of the pvc whose counters would be cleared." + ::= { clear 3 } + + counterClearVci OBJECT-TYPE + SYNTAX INTEGER (1..65535) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "VCI of the pvc whose counters would be cleared." + ::= { clear 4 } + + +---------------------------------------- +-- trap +---------------------------------------- + + object OBJECT IDENTIFIER ::= { trap 1 } +-- dsl OBJECT IDENTIFIER ::= { trap 2 } + equipment OBJECT IDENTIFIER ::= { trap 3 } + systrap OBJECT IDENTIFIER ::= { trap 4 } +-- enet OBJECT IDENTIFIER ::= { trap 5 } + +-------------------- +-- object +-------------------- + + eqptAlarmInputIndex OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The index of alarm input." + ::= { object 2 } + + eqptAlarmInputName OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The Name of alarm input." + ::= { object 8 } + + sysMacAntiSpoofOrig OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The Original port of Mac-AntiSpoofing." + ::= { object 9 } + + sysMacAntiSpoofNew OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The New port of Mac-AntiSpoofing." + ::= { object 10 } + + sysMacAntiSpoofMAC OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The MAC of Mac-AntiSpoofing." + ::= { object 11 } + +-------------------- +-- equipment +-------------------- + + eqptHWMonitorFailure NOTIFICATION-TYPE + STATUS current + DESCRIPTION + "Hardware monitor diagnosis is failed." + ::= { equipment 1 } + +-------------------- +-- systrap +-------------------- + + sysMacAntiSpoofing NOTIFICATION-TYPE + OBJECTS { + sysMacAntiSpoofOrig, + sysMacAntiSpoofNew, + sysMacAntiSpoofMAC + } + STATUS current + DESCRIPTION + "MAC Anti-spoofing." + ::= { systrap 1 } + + sysAlarmCutoffEnable NOTIFICATION-TYPE + STATUS current + DESCRIPTION + "Alarm cutoff is activated." + ::= { systrap 2 } + + sysAlarmClearEnable NOTIFICATION-TYPE + STATUS current + DESCRIPTION + "Alarm clear is activated." + ::= { systrap 3 } + + sysLoginFailure NOTIFICATION-TYPE + STATUS current + DESCRIPTION + "User login is failed." + ::= { systrap 4 } + +------------------------------- +-- 2684 routed mode pvc (rpvc) +------------------------------- + +-- Routed Gateway Table + + rpvcGatewayTable OBJECT-TYPE + SYNTAX SEQUENCE OF RpvcGatewayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes Routed Gateway configuration." + ::= { rpvc 1 } + + rpvcGatewayEntry OBJECT-TYPE + SYNTAX RpvcGatewayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in Routed Gateway table." + INDEX { rpvcGatewayIp } + ::= { rpvcGatewayTable 1 } + + RpvcGatewayEntry ::= + SEQUENCE { + rpvcGatewayIp IpAddress, + rpvcGatewayVlanId VlanIndex, + rpvcGatewayRowStatus RowStatus, + rpvcGatewayPriority INTEGER + } + + rpvcGatewayIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "IP of RPVC gateway." + ::= { rpvcGatewayEntry 1 } + + rpvcGatewayVlanId OBJECT-TYPE + SYNTAX VlanIndex + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Vlan id send to this RPVC gateway." + ::= { rpvcGatewayEntry 2 } + + rpvcGatewayRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object is used to create a new row or delete an existing row in this table." + ::= { rpvcGatewayEntry 3 } + + rpvcGatewayPriority OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "802.1p p bit send to this RPVC gateway." + ::= { rpvcGatewayEntry 4 } + + +-- Routed PVC Table + + rpvcTable OBJECT-TYPE + SYNTAX SEQUENCE OF RpvcTableEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes RPVC configuration." + ::= { rpvc 2 } + + rpvcTableEntry OBJECT-TYPE + SYNTAX RpvcTableEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in rpvcTable." + INDEX { ifIndex, rpvcVpi, rpvcVci, rpvcIp, rpvcNetmask } + ::= { rpvcTable 1 } + + RpvcTableEntry ::= + SEQUENCE { + rpvcVpi INTEGER, + rpvcVci INTEGER, + rpvcDSProfile DisplayString, + rpvcUSProfile DisplayString, + rpvcIp IpAddress, + rpvcNetmask IpAddress, + rpvcGatewayIpAddress IpAddress, + rpvcRowStatus RowStatus + } + + rpvcVpi OBJECT-TYPE + SYNTAX INTEGER (0..255) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VPI of the rpvc." + ::= { rpvcTableEntry 1 } + + rpvcVci OBJECT-TYPE + SYNTAX INTEGER (1..65535) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VCI of the rpvc." + ::= { rpvcTableEntry 2 } + + rpvcDSProfile OBJECT-TYPE + SYNTAX DisplayString (SIZE (1..31)) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The down stream profile of the rpvc." + ::= { rpvcTableEntry 3 } + + rpvcUSProfile OBJECT-TYPE + SYNTAX DisplayString (SIZE (1..31)) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The up stream profile of the rpvc." + ::= { rpvcTableEntry 4 } + + rpvcIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The IP of the rpvc." + ::= { rpvcTableEntry 5 } + + rpvcNetmask OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The IP mask of the rpvc IP." + ::= { rpvcTableEntry 6 } + + rpvcGatewayIpAddress OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The gateway IP of rpvc." + ::= { rpvcTableEntry 7 } + + rpvcRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object is used to create a new row or delete an existing row in this table." + ::= { rpvcTableEntry 8 } + +-- Routed PVC Routed Domain Table + + rpvcRouteDomainTable OBJECT-TYPE + SYNTAX SEQUENCE OF RpvcRouteDomainTableEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes RPVC route domain configuration." + ::= { rpvc 3 } + + rpvcRouteDomainTableEntry OBJECT-TYPE + SYNTAX RpvcRouteDomainTableEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in rpvcRouteDomainTable." + INDEX { ifIndex, rpvcRouteDomainVpi, rpvcRouteDomainVci, rpvcRouteDomainIp, rpvcRouteDomainNetmask } + ::= { rpvcRouteDomainTable 1 } + + RpvcRouteDomainTableEntry ::= + SEQUENCE { + rpvcRouteDomainVpi INTEGER, + rpvcRouteDomainVci INTEGER, + rpvcRouteDomainIp IpAddress, + rpvcRouteDomainNetmask IpAddress, + rpvcRouteDomainRowStatus RowStatus + } + + rpvcRouteDomainVpi OBJECT-TYPE + SYNTAX INTEGER (0..255) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VPI of the rpvc." + ::= { rpvcRouteDomainTableEntry 1 } + + rpvcRouteDomainVci OBJECT-TYPE + SYNTAX INTEGER (1..65535) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VCI of the rpvc." + ::= { rpvcRouteDomainTableEntry 2 } + + rpvcRouteDomainIp OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The route domain IP." + ::= { rpvcRouteDomainTableEntry 3 } + + rpvcRouteDomainNetmask OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The IP mask of the route domain IP." + ::= { rpvcRouteDomainTableEntry 4 } + + rpvcRouteDomainRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object is used to create a new row or delete an existing row in this table." + ::= { rpvcRouteDomainTableEntry 5 } + + rpvcArpAgingTime OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Set RPVC ARP proxy aging time 10..10000 seconds, + 0 to disable againg." + ::= { rpvc 4 } + + rpvcArpFlush OBJECT-TYPE + SYNTAX INTEGER { + enable(1) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Flush the RPVC ARP proxy table." + ::= { rpvc 5 } + +-- DS Bcast diable control Table + + dsBcastDisableTable OBJECT-TYPE + SYNTAX SEQUENCE OF DsBcastDisableEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table includes Down Stream Bcast configuration." + ::= { port 9 } + + dsBcastDisableEntry OBJECT-TYPE + SYNTAX DsBcastDisableEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in Down Stream Bcast table." + INDEX { ifIndex, dsBcastDisableVlanId } + ::= { dsBcastDisableTable 1 } + + DsBcastDisableEntry ::= + SEQUENCE { + dsBcastDisableVlanId INTEGER, + dsBcastDisableRowStatus RowStatus + } + + dsBcastDisableVlanId OBJECT-TYPE + SYNTAX INTEGER + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "downstream broadcast disabled vid." + ::= { dsBcastDisableEntry 1 } + + dsBcastDisableRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object is used to create a new row or delete an existing row in this table." + ::= { dsBcastDisableEntry 2 } + +END |