diff options
Diffstat (limited to 'MIBS/transition/TN-VLAN-MGMT-MIB')
| -rw-r--r-- | MIBS/transition/TN-VLAN-MGMT-MIB | 1723 |
1 files changed, 1723 insertions, 0 deletions
diff --git a/MIBS/transition/TN-VLAN-MGMT-MIB b/MIBS/transition/TN-VLAN-MGMT-MIB new file mode 100644 index 0000000..7f57896 --- /dev/null +++ b/MIBS/transition/TN-VLAN-MGMT-MIB @@ -0,0 +1,1723 @@ +-- ***********************************************************************************************
+-- TN-VLAN-MGMT-MIB.mib: Transition Networks, Inc. Enterprise MIB for VLAN management
+--
+-- Copyright (c) 2014 by Transition Networks, Inc.
+-- All rights reserved.
+--
+-- ***********************************************************************************************
+--
+
+TN-VLAN-MGMT-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+ MODULE-IDENTITY,
+ OBJECT-TYPE, NOTIFICATION-TYPE, IpAddress,
+ enterprises FROM SNMPv2-SMI
+ RowStatus, MacAddress,
+ TEXTUAL-CONVENTION, DisplayString, TimeStamp, TruthValue FROM SNMPv2-TC
+ entPhysicalIndex FROM ENTITY-MIB
+ InterfaceIndexOrZero, InterfaceIndex, ifIndex FROM IF-MIB
+ VlanIndex, PortList FROM Q-BRIDGE-MIB
+ EightOTwoOui FROM DOT3-OAM-MIB
+ SnmpAdminString FROM SNMP-FRAMEWORK-MIB
+ tnProducts FROM TRANSITION-SMI;
+
+tnVlanQoSMgmtMIB MODULE-IDENTITY
+ LAST-UPDATED "201405010000Z"
+ ORGANIZATION "Transition Networks, Inc."
+ CONTACT-INFO
+ " Transition Networks
+ Technical Support
+
+ 10900 Red Circle Drive
+ Minnetonka, MN 55343 USA
+ Tel: +1-800-526-9267
+
+ E-mail: techsupport@transition.com"
+ DESCRIPTION
+ "The mib module for managing VLAN and QoS in TN platform products."
+
+ REVISION "200901080000Z"
+ DESCRIPTION
+ "Initial Revision of this module"
+ REVISION "201102250000Z"
+ DESCRIPTION
+ "Add tnVLANDbFlush and tnFIDDbFlush"
+ REVISION "201205180000Z"
+ DESCRIPTION
+ "Add tnSysVlanExtMgmtPortType, tnSysVLANExtCustomSTag, tnIfVLANTagMgmt2PortType,
+ tnIfVLANTagMgmt2TxTagType and tnIfVLANTagMgmt2ConfigConflicts"
+ REVISION "201212210000Z"
+ DESCRIPTION
+ "Add Vlan Control List tnVclMgmt subtree"
+ REVISION "201405010000Z"
+ DESCRIPTION
+ "Added Port VLAN Configuration Mode, Allowed VLANs, Forbidden VLANs"
+
+ REVISION "201506170000Z"
+ DESCRIPTION
+ "Added Allowed Access VLANs
+ tnVlanConfigGlobalsMainAccessVlans0To1K
+ tnVlanConfigGlobalsMainAccessVlans1KTo2K
+ tnVlanConfigGlobalsMainAccessVlans2KTo3K
+ tnVlanConfigGlobalsMainAccessVlans3KTo4K"
+
+ ::= { tnProducts 4 }
+
+--
+-- Textual Conventions
+--
+TnVlanServiceTranslationType ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "T"
+ SYNTAX INTEGER {
+ noTranslation(1),
+ untaggedUntagged(2),
+ untaggedSingleTagged(3),
+ singleTaggedSingleTagged(4),
+ singleTaggedTranslation(5),
+ singleTaggedDoubleTagged(6),
+ doubleTaggedDoubleTagged(7),
+ doubleTaggedTranslation(8),
+ addProviderTag(9)
+ }
+
+TNVlanListQuarter ::= TEXTUAL-CONVENTION
+ DISPLAY-HINT "128x"
+ STATUS current
+ DESCRIPTION
+ "A list representing 1024 VLAN IDs.
+
+ The type should be interpreted as a sequence of bits, each bit
+ representing one VLAN ID. If a bit is set (1) the represented VLAN is
+ included in the VLAN list. If a bit is not set (0) the represented VLAN
+ is not included in the VLAN list.
+
+ The least significant bit of each byte represents a smaller VLAN ID
+ than a more significant bit of a byte.
+
+ If for example the VLAN list represents VLAN IDs from 0 to 1023,
+ bit 0 of the first byte represents VLAN ID 0, bit 1 of the first byte
+ represents VLAN ID 1, and so on. The most significant bit of the 128th
+ byte therefore represents VLAN ID 1023.
+
+ An implementation that needs to represent all 4K VLANs will divide
+ the VLAN list into four equally sized objects. VLAN ID 0 is included
+ in the first object even though it is not used."
+ SYNTAX OCTET STRING (SIZE (128))
+
+--
+-- Section 1 :
+--
+tnVlanQoSMgmtNotifications OBJECT IDENTIFIER ::= { tnVlanQoSMgmtMIB 0 }
+tnVlanQoSMgmtObjects OBJECT IDENTIFIER ::= { tnVlanQoSMgmtMIB 1 }
+tnVlanMQoSgmtConformance OBJECT IDENTIFIER ::= { tnVlanQoSMgmtMIB 2 }
+
+--
+-- TN Vlan management information
+--
+tnSysVlanMgmt OBJECT IDENTIFIER ::= { tnVlanQoSMgmtObjects 1 }
+tnDevSysPriorityMgmt OBJECT IDENTIFIER ::= { tnVlanQoSMgmtObjects 2 }
+tnInterfaceQoSMgmt OBJECT IDENTIFIER ::= { tnVlanQoSMgmtObjects 3 }
+tnInterfaceVlanMgmt OBJECT IDENTIFIER ::= { tnVlanQoSMgmtObjects 4 }
+tnVlanServiceMgmt OBJECT IDENTIFIER ::= { tnVlanQoSMgmtObjects 5 }
+tnVlanDbMgmt OBJECT IDENTIFIER ::= { tnVlanQoSMgmtObjects 6 }
+tnFIDDbMgmt OBJECT IDENTIFIER ::= { tnVlanQoSMgmtObjects 7 }
+tnVclMgmt OBJECT IDENTIFIER ::= { tnVlanQoSMgmtObjects 8 }
+--
+-- Management VLAN
+--
+tnSysManagmentVLANTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnSysManagmentVLANEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Management VLAN configuration table."
+ ::= { tnSysVlanMgmt 1 }
+
+tnSysManagmentVLANEntry OBJECT-TYPE
+ SYNTAX TnSysManagmentVLANEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry represents the management VLAN entry on a device."
+ INDEX { entPhysicalIndex }
+ ::= { tnSysManagmentVLANTable 1 }
+
+TnSysManagmentVLANEntry ::=
+ SEQUENCE
+ {
+ tnSysMgmtVLANStatus INTEGER,
+ tnSysMgmtVLANId INTEGER,
+ tnSysMgmtMemberPorts BITS
+ }
+
+tnSysMgmtVLANStatus OBJECT-TYPE
+ SYNTAX INTEGER { enabled(1), disabled(2) }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The device if management VLAN capable, can enable the secure channel
+ for all its management traffic by setting this variable to enabled(1)."
+ ::= { tnSysManagmentVLANEntry 1 }
+
+tnSysMgmtVLANId OBJECT-TYPE
+ SYNTAX INTEGER (1..4094)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The VLAN id, that this device will use for its management traffic.
+ All Management frames to this device when 'tnSysManagmentVLANStatus'
+ is set to 'enabled(1)' must be tagged with this VLAN id and all
+ management frames from this device will be tagged with this VLAN id."
+ ::= { tnSysManagmentVLANEntry 2 }
+
+tnSysMgmtMemberPorts OBJECT-TYPE
+ SYNTAX BITS { none(0) } -- value added by Jing
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The ports on this device which are members of this Management VLAN.
+ This is for security, some ports can be made not a member, which blocks all
+ management access from this port.
+ Each bit in this variable represents the logical port number local to the device."
+ ::= { tnSysManagmentVLANEntry 3 }
+
+--
+-- TN Switch management information
+--
+
+tnSysVLANExtTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnSysVLANExtEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "System VLAN external configuration table."
+ ::= { tnSysVlanMgmt 2 }
+
+tnSysVLANExtEntry OBJECT-TYPE
+ SYNTAX TnSysVLANExtEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry represents the VLAN config on a device."
+ INDEX { entPhysicalIndex }
+ ::= { tnSysVLANExtTable 1 }
+
+TnSysVLANExtEntry ::=
+ SEQUENCE
+ {
+ tnSysVlanExtMgmtPortType INTEGER,
+ tnSysVLANExtCustomSTag OCTET STRING,
+ tnVlanConfigGlobalsMainAccessVlans0To1K TNVlanListQuarter,
+ tnVlanConfigGlobalsMainAccessVlans1KTo2K TNVlanListQuarter,
+ tnVlanConfigGlobalsMainAccessVlans2KTo3K TNVlanListQuarter,
+ tnVlanConfigGlobalsMainAccessVlans3KTo4K TNVlanListQuarter
+ }
+
+tnSysVlanExtMgmtPortType OBJECT-TYPE
+ SYNTAX INTEGER{
+ unaware(1),
+ cPort(2),
+ sPort(3),
+ sCustomPort(4)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This mib variable is applicable for products that have a out of band management port.
+ This determines the Port type for all management traffic.It can be one of the following types:
+ Unaware, C-port, S-port, or S-custom-port where:
+ - Unaware: The management traffic is untagged or not management vlan.
+ - C-port: The management vlan is a C-Vlan and TPID 0x8100 is used for out of band management traffic.
+ - S-port: The management vlan is a S-Vlan and TPID 0x88a8 is used for out of band management traffic.
+ - S-custom-port: The management vlan is a S-Vlan, which use a custom TPID defined in tnSysVLANExtCustomSTag.
+ "
+ ::= { tnSysVLANExtEntry 1 }
+
+tnSysVLANExtCustomSTag OBJECT-TYPE
+ SYNTAX OCTET STRING(SIZE(2))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This field specifies the Ether type used for Custom S-ports.
+ This is a global setting and is applicable for all Custom S-ports.
+ This field is used when TPID other than 0x8100 and 0x88a8 is needed for S-Tags."
+ ::= { tnSysVLANExtEntry 2 }
+
+ tnVlanConfigGlobalsMainAccessVlans0To1K OBJECT-TYPE
+ SYNTAX TNVlanListQuarter
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "First quarter of bit-array indicating the enabled access VLANs."
+ ::= { tnSysVLANExtEntry 3 }
+
+tnVlanConfigGlobalsMainAccessVlans1KTo2K OBJECT-TYPE
+ SYNTAX TNVlanListQuarter
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Second quarter of bit-array indicating the enabled access VLANs."
+ ::= { tnSysVLANExtEntry 4 }
+
+tnVlanConfigGlobalsMainAccessVlans2KTo3K OBJECT-TYPE
+ SYNTAX TNVlanListQuarter
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Third quarter of bit-array indicating the enabled access VLANs."
+ ::= { tnSysVLANExtEntry 5 }
+
+tnVlanConfigGlobalsMainAccessVlans3KTo4K OBJECT-TYPE
+ SYNTAX TNVlanListQuarter
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Last quarter of bit-array indicating the enabled access VLANs."
+ ::= { tnSysVLANExtEntry 6 }
+
+-- IP Priority mapping Table
+tnSwIPPrioTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnSwIPPrioEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "IP Traffic class table."
+ ::= { tnDevSysPriorityMgmt 1 }
+
+tnSwIPPrioEntry OBJECT-TYPE
+ SYNTAX TnSwIPPrioEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry represents the remapped value for each traffic class."
+ INDEX { tnSwIPPrioIndex }
+ ::= { tnSwIPPrioTable 1 }
+
+TnSwIPPrioEntry ::=
+ SEQUENCE
+ {
+ tnSwIPPrioIndex INTEGER,
+ tnSwIPPrioTC INTEGER,
+ tnSwIPPrioRemap INTEGER
+ }
+
+tnSwIPPrioIndex OBJECT-TYPE
+ SYNTAX INTEGER (1..11111) -- range added by Jing
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The IP traffic class remap table index. The indexing is for a bridge entity"
+ ::= { tnSwIPPrioEntry 1 }
+
+tnSwIPPrioTC OBJECT-TYPE
+ SYNTAX INTEGER
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The IP traffic class value."
+ ::= { tnSwIPPrioEntry 2 }
+
+tnSwIPPrioRemap OBJECT-TYPE
+ SYNTAX INTEGER { pri0(1), pri1(2), pri2(3), pri3(4) }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The frames with IP traffic class set, will be remapped to the listed priority queues."
+ ::= { tnSwIPPrioEntry 3 }
+
+-- IEEE Priority mapping Table
+tnSwIEEEPrioTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnSwIEEEPrioEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "IEEE priority remapping table."
+ ::= { tnDevSysPriorityMgmt 2 }
+
+tnSwIEEEPrioEntry OBJECT-TYPE
+ SYNTAX TnSwIEEEPrioEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry represents the remapped value for each priority class."
+ INDEX { tnSwIEEEPriority }
+ ::= { tnSwIEEEPrioTable 1 }
+
+TnSwIEEEPrioEntry ::=
+ SEQUENCE
+ {
+ tnSwIEEEPriority INTEGER,
+ tnSwIEEEPriorityRemap INTEGER
+ }
+
+tnSwIEEEPriority OBJECT-TYPE
+ SYNTAX INTEGER (0..7)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The IEEE tag priority bits in the frame."
+ ::= { tnSwIEEEPrioEntry 1 }
+
+tnSwIEEEPriorityRemap OBJECT-TYPE
+ SYNTAX INTEGER { pri0(1), pri1(2), pri2(3), pri3(4) }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The frames with IEEE priority bits set, will be mapped to the listed priority queues."
+ ::= { tnSwIEEEPrioEntry 2 }
+
+--
+-- ION Interface Priority Management
+--
+tnIfPriorityTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnIfPriorityEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table has entries for interfaces which are capable of Priority management."
+ ::= { tnInterfaceQoSMgmt 1 }
+
+tnIfPriorityEntry OBJECT-TYPE
+ SYNTAX TnIfPriorityEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A entry in the table represents Priority configuration."
+ INDEX { ifIndex }
+ ::= { tnIfPriorityTable 1 }
+
+TnIfPriorityEntry ::=
+ SEQUENCE
+ {
+ tnIfDefaultPriority INTEGER,
+ tnIfUseIEEEPriority TruthValue,
+ tnIfUseIPPriority TruthValue,
+ tnIfUseIPOrIEEEPriority INTEGER,
+ tnIfSrcMACPriorityRemap TruthValue,
+ tnIfDstMACPriorityRemap TruthValue,
+ tnIfVIDPriorityRemap TruthValue
+ }
+
+tnIfDefaultPriority OBJECT-TYPE
+ SYNTAX INTEGER (0..7)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The default priority for frames ingressing this port, if it doesnt have any
+ IEEE 802.3ac tag or any IP TOS/Diffserv traffic class fields."
+ ::= { tnIfPriorityEntry 1 }
+
+tnIfUseIEEEPriority OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If the frame is IEEE tagged, and this mib variable is set to 'true',
+ the 802.1p bits are used as the frames priority."
+ ::= { tnIfPriorityEntry 2 }
+
+tnIfUseIPPriority OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If the frame has IP TOS/Diffserv traffic class fields, and this mib variable is
+ set to 'true'. The traffic class fields will be used as the frame's priority."
+ ::= { tnIfPriorityEntry 3 }
+
+tnIfUseIPOrIEEEPriority OBJECT-TYPE
+ SYNTAX INTEGER { useIEEE(1), useIP(2) }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If the frame has IP TOS/Diffserv traffic class fields, and IEEE 802.3ac tagged, then
+ this mib variable decides which one is to be considered as the frame's priority."
+ ::= { tnIfPriorityEntry 4 }
+
+tnIfSrcMACPriorityRemap OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "When set to true(1), a frame's Source MAC address decides the priority of the frame.
+ The new priority value is assigned based on the priority assigned to that MAC address
+ in the MAC forwarding database."
+ ::= { tnIfPriorityEntry 5 }
+
+tnIfDstMACPriorityRemap OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "When set to true(1), a frame's Destination MAC address decides the priority of the frame.
+ The new priority value is assigned based on the priority assigned to that MAC address
+ in the MAC forwarding database."
+ ::= { tnIfPriorityEntry 6 }
+
+tnIfVIDPriorityRemap OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "When set to true(1), a frame's VLAN id decides the priority of the frame.
+ The new priority value is assigned based on the priority assigend to that VLAN id
+ in the VLAN database."
+ ::= { tnIfPriorityEntry 7 }
+
+--
+-- ION Interface Priority remapping
+--
+tnIfPriorityRemapTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnIfPriorityRemapEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table has entries for each interface's IEEE priority remapping."
+ ::= { tnInterfaceQoSMgmt 2 }
+
+tnIfPriorityRemapEntry OBJECT-TYPE
+ SYNTAX TnIfPriorityRemapEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A entry in the table represents Priority remapping for an interface."
+ INDEX { ifIndex, tnIfUserPriority }
+ ::= { tnIfPriorityRemapTable 1 }
+
+TnIfPriorityRemapEntry ::=
+ SEQUENCE
+ {
+ tnIfUserPriority INTEGER,
+ tnIfRemappedPriority INTEGER
+ }
+
+tnIfUserPriority OBJECT-TYPE
+ SYNTAX INTEGER (0..7)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The priority found in the frames ingressing this interface.
+ Frames which are untagged take up the interface's priority."
+ ::= { tnIfPriorityRemapEntry 1 }
+
+tnIfRemappedPriority OBJECT-TYPE
+ SYNTAX INTEGER (0..7)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The frame's priority is remapped to this new priority value.
+ Frames that egress tagged will have the remapped priority."
+ ::= { tnIfPriorityRemapEntry 2 }
+
+--
+-- ION Interface VLAN Management
+--
+tnIfVLANTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnIfVLANEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table has entries for interfaces which are VLAN capable."
+ ::= { tnInterfaceVlanMgmt 1 }
+
+tnIfVLANEntry OBJECT-TYPE
+ SYNTAX TnIfVLANEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A entry in the table represents VLAN configuration on an interface."
+ INDEX { ifIndex }
+ ::= { tnIfVLANTable 1 }
+
+TnIfVLANEntry ::=
+ SEQUENCE
+ {
+ tnIfDot1qState INTEGER,
+ tnIfDiscardTagged TruthValue,
+ tnIfDiscardUntagged TruthValue,
+ tnIfDefaultVlanId INTEGER,
+ tnIfForceDefaultVlanId TruthValue
+ }
+
+tnIfDot1qState OBJECT-TYPE
+ SYNTAX INTEGER { vlanEnabled(1), vlanDisabled(2) }
+ MAX-ACCESS read-write
+ STATUS current
+-- SYNTAX INTEGER { vlanDisabled(1), fallback(2), check(3), secure(4) }
+-- MAX-ACCESS read-write
+-- STATUS current
+-- DESCRIPTION
+-- "The IEEE 802.1Q status of this inteface.
+-- vlanDisabled - 802.1Q is disabled.
+-- fallback - The frame is not discarded if the Vlan Id is not in the VLAN Database. It is forwarded normally.
+-- check - The Vlan Id must be in the VLAN Database, the ingress port may or may not be a member.
+-- If the Vlan Id is not in the VLAN Database, it is discarded.
+-- secure - The Vlan Id must be in the VLAN Database and the ingresss port should be a member
+-- of the VLAN, else it is discarded.
+-- In all the three cases when 802.1Q is enabled, the frame is allowed to egress only port is a member of the VLAN."
+ DESCRIPTION
+ "The IEEE802.1Q status of this interface."
+ ::= { tnIfVLANEntry 1 }
+
+tnIfDiscardTagged OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This filters all tagged non-management frames ingressing this port.
+ All untagged and priority tagged frames are processed as normal frames."
+ ::= { tnIfVLANEntry 2 }
+
+tnIfDiscardUntagged OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This filters all untagged and priority tagged non-management frames
+ ingressing this port. All frames .1Q tagged frames are processed as normal frames."
+ ::= { tnIfVLANEntry 3 }
+
+tnIfDefaultVlanId OBJECT-TYPE
+ SYNTAX INTEGER (0..4094)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The interface's default Vlan id. This VLAN id is given to untagged frames on ingress into
+ the device."
+ ::= { tnIfVLANEntry 4 }
+
+tnIfForceDefaultVlanId OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This forces all untagged and (802.1Q)tagged frames to take up the interface's ionIfDefaultVlanId."
+ ::= { tnIfVLANEntry 5 }
+
+--
+-- Tagging options at Port Level
+--
+tnIfVLANTagMgmtTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnIfVLANTagMgmtEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table has entries for interfaces which are VLAN capable."
+ ::= { tnInterfaceVlanMgmt 2 }
+
+tnIfVLANTagMgmtEntry OBJECT-TYPE
+ SYNTAX TnIfVLANTagMgmtEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A entry in the table represents VLAN configuration on an interface."
+ INDEX { ifIndex }
+ ::= { tnIfVLANTagMgmtTable 1 }
+
+TnIfVLANTagMgmtEntry ::=
+ SEQUENCE
+ {
+ tnIfFrameTagMode INTEGER,
+ tnIfProviderEtherType INTEGER,
+ tnIfNetworkModeTagging INTEGER
+ }
+
+tnIfFrameTagMode OBJECT-TYPE
+ SYNTAX INTEGER { network(1), provider(2), customer(3) }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The interface's taggin mode. The interface can be set as :
+ network(1) - This is the normal network mode. It can take untagged
+ and 802.3ac tagged frames. In this mode, 802.1q can be
+ enabled on the interface. Frames with an ethertype of
+ 0x8100 is considered as tagged.
+
+ provider(2) - In provider mode, frames are considered
+ provider tagged if it matches the 'ionIfProviderEtherType'.
+ Frames which are ingress with a provider tag, are stripped
+ of their provider tag on egressing this interface.
+ If the frame's ethertype doesnt match the 'ionIfProviderEtherType'
+ it is as untagged.
+
+ customer(3) - The customer mode is a normal access port which is not 802.1Q aware.
+ "
+ ::= { tnIfVLANTagMgmtEntry 1 }
+
+tnIfProviderEtherType OBJECT-TYPE
+ SYNTAX INTEGER { x8100(1), x9100(2), x88a8(3) }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This ether type is used when an interface is set to 'provider' mode.
+ Frames are considered tagged only if the ether type matches this value."
+ ::= { tnIfVLANTagMgmtEntry 2 }
+
+tnIfNetworkModeTagging OBJECT-TYPE
+ SYNTAX INTEGER { unmodified(1), removeTag(2), addTag(3) }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This is available only when 'ionIfFrameTagMode' is set to 'network(1)' mode.
+ In unmodified(1) - Frames are unmodified, the egress the same as they ingress this interface
+ removeTag(2) - Tagged frames are stripped of their tag, and are transmitted untagged
+ addTag(3) - Untagged frames get tagged when they egress this interface."
+ ::= { tnIfVLANTagMgmtEntry 3 }
+
+tnIfVLANTagMgmt2Table OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnIfVLANTagMgmt2Entry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table has entries for interfaces which are VLAN capable."
+ ::= { tnInterfaceVlanMgmt 3 }
+
+tnIfVLANTagMgmt2Entry OBJECT-TYPE
+ SYNTAX TnIfVLANTagMgmt2Entry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A entry in the table represents VLAN configuration on an interface."
+ INDEX { ifIndex }
+ ::= { tnIfVLANTagMgmt2Table 1 }
+
+TnIfVLANTagMgmt2Entry ::=
+ SEQUENCE
+ {
+ tnIfVLANTagMgmt2PortType INTEGER,
+ tnIfVLANTagMgmt2TxTagType INTEGER,
+ tnIfVLANTagMgmt2ConfigConflicts INTEGER,
+ tnVlanConfigInterfaceMode INTEGER,
+ tnVlanConfigInterfaceAllowVlans0KTo1K TNVlanListQuarter,
+ tnVlanConfigInterfaceAllowVlans1KTo2K TNVlanListQuarter,
+ tnVlanConfigInterfaceAllowVlans2KTo3K TNVlanListQuarter,
+ tnVlanConfigInterfaceAllowVlans3KTo4K TNVlanListQuarter,
+ tnVlanConfigInterfaceForbiddenVlans0KTo1K TNVlanListQuarter,
+ tnVlanConfigInterfaceForbiddenVlans1KTo2K TNVlanListQuarter,
+ tnVlanConfigInterfaceForbiddenVlans2KTo3K TNVlanListQuarter,
+ tnVlanConfigInterfaceForbiddenVlans3KTo4K TNVlanListQuarter
+ }
+
+tnIfVLANTagMgmt2PortType OBJECT-TYPE
+ SYNTAX INTEGER{
+ unaware(1),
+ cPort(2),
+ sPort(3),
+ sCustomPort(4)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "A Port can be one of the following types: Unaware, C-port, S-port, or S-custom-port where:
+ - Unaware: all frames are classified to the Port VLAN ID and tags are not removed (default).
+ - C-port: Customer port; with Customer tags (C-Tags), which use TPID 0x8100.
+ - S-port: Service port; with Service tags (S-Tags), which use TPID 0x88A8 (IEEE 802.1ad).
+ - S-custom-port: Custom Service port; with Service tags (S-Tags), which use a custom TPID assigned
+ in tnSysVLANExtCustomSTag.
+ For Customer tags and Service tags, both VLAN tags (tags with non-zero VID) and Priority tags (tags with
+ VID = 0) are processed.
+ The tag header is either retrieved from a tag in the incoming frame or from a default port-based tag header.
+ The port-based tag header is configured in ieee8021QBridgePvid.
+ For double-tagged frames, there is an option to use the inner tag instead of the outer tag.
+ In addition to the tag header, the ingress port decides the number of VLAN tags to pop at egress. If the
+ configured number of tags to pop is greater than the actual number of tags in the frame, the number is
+ reduced to the actual number of tags in the frame. "
+ ::= { tnIfVLANTagMgmt2Entry 1 }
+
+tnIfVLANTagMgmt2TxTagType OBJECT-TYPE
+ SYNTAX INTEGER {
+ untagPvid(1),
+ tagAll(2),
+ untagAll(3)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Determines egress tagging on a port:
+ - Untag_pvid - All frames with classified VLAN as the PVID egress as untagged frames.
+ - Tag_all - All frames which do not have a tag with classified vlan are tagged on egress.
+ An extra tag with ingress port PVID is added if the frames are already tagged.
+ - Untag_all - All frames tagged with the classified vlan id are untagged on egress."
+ ::= { tnIfVLANTagMgmt2Entry 2 }
+
+tnIfVLANTagMgmt2ConfigConflicts OBJECT-TYPE
+ SYNTAX INTEGER {
+ no(1),
+ yes(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Shows the status of Conflicts whether one exists or not. When a Volatile VLAN User requests to set VLAN
+ membership or VLAN port configuration, the following conflicts can occur:
+
+ - Functional Conflicts between features.
+ - Conflicts due to hardware limitation.
+ - Direct conflict between user modules. "
+ ::= { tnIfVLANTagMgmt2Entry 3 }
+
+tnVlanConfigInterfaceMode OBJECT-TYPE
+ SYNTAX INTEGER { access(1), trunk(2), hybrid(3) }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Determines the underlying port mode.
+
+ Access ports are only members of one VLAN, the AccessVlan.
+
+ Trunk ports are by default members of all VLANs, which can be limited
+ with TrunkVlans.
+
+ Hybrid ports allow for changing all port VLAN parameters. As trunk
+ ports, hybrid ports are by default members of all VLANs, which can be
+ limited with HybridVlans."
+ ::= { tnIfVLANTagMgmt2Entry 4 }
+
+tnVlanConfigInterfaceAllowVlans0KTo1K OBJECT-TYPE
+ SYNTAX TNVlanListQuarter
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "First quarter of bit-array indicating whether the port is member of a
+ VLAN ('1') or not ('0'). Used when Mode is hybrid."
+ ::= { tnIfVLANTagMgmt2Entry 5 }
+
+tnVlanConfigInterfaceAllowVlans1KTo2K OBJECT-TYPE
+ SYNTAX TNVlanListQuarter
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Second quarter of bit-array indicating whether the port is member of a
+ VLAN ('1') or not ('0'). Used when Mode is hybrid."
+ ::= { tnIfVLANTagMgmt2Entry 6 }
+
+tnVlanConfigInterfaceAllowVlans2KTo3K OBJECT-TYPE
+ SYNTAX TNVlanListQuarter
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Third quarter of bit-array indicating whether the port is member of a
+ VLAN ('1') or not ('0'). Used when Mode is hybrid."
+ ::= { tnIfVLANTagMgmt2Entry 7 }
+
+tnVlanConfigInterfaceAllowVlans3KTo4K OBJECT-TYPE
+ SYNTAX TNVlanListQuarter
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Last quarter of bit-array indicating whether the port is member of a
+ VLAN ('1') or not ('0'). Used when Mode is hybrid."
+ ::= { tnIfVLANTagMgmt2Entry 8 }
+
+tnVlanConfigInterfaceForbiddenVlans0KTo1K OBJECT-TYPE
+ SYNTAX TNVlanListQuarter
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "First quarter of bit-array indicating whether the port can ever become
+ a member of a VLAN ('0') or not ('1'). Used in all modes."
+ ::= { tnIfVLANTagMgmt2Entry 9 }
+
+tnVlanConfigInterfaceForbiddenVlans1KTo2K OBJECT-TYPE
+ SYNTAX TNVlanListQuarter
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Second quarter of bit-array indicating whether the port can ever become
+ a member of a VLAN ('0') or not ('1'). Used in all modes."
+ ::= { tnIfVLANTagMgmt2Entry 10 }
+
+tnVlanConfigInterfaceForbiddenVlans2KTo3K OBJECT-TYPE
+ SYNTAX TNVlanListQuarter
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Third quarter of bit-array indicating whether the port can ever become
+ a member of a VLAN ('0') or not ('1'). Used in all modes."
+ ::= { tnIfVLANTagMgmt2Entry 11 }
+
+tnVlanConfigInterfaceForbiddenVlans3KTo4K OBJECT-TYPE
+ SYNTAX TNVlanListQuarter
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Last quarter of bit-array indicating whether the port can ever become a
+ member of a VLAN ('0') or not ('1'). Used in all modes."
+ ::= { tnIfVLANTagMgmt2Entry 12 }
+
+--
+-- VLAN service configuration for a 2-port ION device
+--
+tnVlanServiceConnType OBJECT-TYPE
+ SYNTAX INTEGER { customerProvider(1), providerCustomer(2) }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This defines the VLAN service type. The connection specified Port 1 and Port 2 configuration.
+ customerProvider(1) : This sets the Port 1 to be customer facing port and Port 2 to be provider facing port.
+ providerCustomer(2) : This sets the Port 1 to be provider facing port and Port 2 to be customer facing port.
+ "
+ ::= { tnVlanServiceMgmt 1 }
+
+tnVlanServiceVIDForTag OBJECT-TYPE
+ SYNTAX INTEGER (1..4094)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This Vlan id will be used when the service translation requires an extra tag to be added."
+ ::= { tnVlanServiceMgmt 2 }
+
+tnVlanServiceEtherTypeForTag OBJECT-TYPE
+ SYNTAX INTEGER
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This Ethertype will be used when the service translation requires an extra tag to be added.
+ Typical values are 0x8100 for IEEE 802.1Q tags, 0x88a8 for IEEE 802.1ad S-tags or other 2 byte private ethertype."
+ ::= { tnVlanServiceMgmt 3 }
+
+tnVlanServiceTranslation OBJECT-TYPE
+ SYNTAX TnVlanServiceTranslationType
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This determines the service or flow type between the two terminations.
+ The translation type as the flow passes the termination points from Customer edge to provider edge
+ are detailed below :
+
+
+ <----- Provider Side -----> <----- Customer Side ----->
+ Device
+ +------------------------------+
+ ----> | P | | P | ---->
+ ----> | o | | o | ---->
+ <---- | r | | r | <----
+ <---- | t | | t | <----
+ |(PE)| |(CE)|
+ +------------------------------+
+
+
+ noTranslation(1) :-
+ The ingress flow might contain any kind of frames, untagged or single or double tagged.
+ The egress flow will be exactly the same, no translation is done.
+
+ untaggedUntagged(2) :-
+ The traffic should be untagged, all tagged frames will be discarded.
+ The traffic that egress the device contain the untagged flow without any modification.
+
+ untaggedSingleTagged(3) :-
+ At the CE the traffic should be untagged.
+ At the PE the traffic will contain a single tag with the VID specified in tnVlanServiceVIDForTag.
+
+ singleTaggedSingleTagged(4) :-
+ The traffic should be single tagged on ingress and on egress with no translation.
+
+ singleTaggedTranslation(5) :-
+ The traffic should be single tagged on ingress and on egress.
+ The only changes from the singleTaggedSingleTagged(4), there is a translation.
+ The Vlan Id that came on ingress is translated to a different Vlan Id on egress.
+
+ singleTaggedDoubleTagged(6) :-
+ At the CE the traffic should be single tagged.
+ At the PE the traffic will contain an extra tag with the VID specified in tnVlanServiceVIDForTag.
+
+ doubleTaggedDoubleTagged(7) :-
+ The traffic should be double tagged on ingress and on egress with no translation.
+
+ doubleTaggedTranslation(8) :-
+ The traffic should be double tagged on ingress and on egress.
+ The only changes from the doubleTaggedDoubleTagged(7), there is a translation.
+ The Vlan Id in outer tag that came on CE is translated to a different Vlan Id on PE.
+ The inner tag remains intact.
+
+ addProviderTag(9) :-
+ This option adds an extra tag on the PE interface, no matter what kind of traffic at CE.
+ This strips the outer tag for traffic from PE interface egressing the CE interface.
+ "
+ ::= { tnVlanServiceMgmt 4 }
+
+--
+-- VLAN database
+--
+tnVLANDbTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnVLANDbEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table contains all VLAN entries for this bridge."
+ ::= { tnVlanDbMgmt 1 }
+
+tnVLANDbEntry OBJECT-TYPE
+ SYNTAX TnVLANDbEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A entry in the table represents a VLAN and the interfaces that are members of that VLAN."
+ INDEX { tnVlanDbVID }
+ ::= { tnVLANDbTable 1 }
+
+TnVLANDbEntry ::=
+ SEQUENCE
+ {
+ tnVlanDbVID VlanIndex,
+ tnVlanDbFID INTEGER,
+ tnVlanDbVIDPriOverride INTEGER,
+ tnVlanDbVIDPriority INTEGER,
+ tnVlanDbMemTagPort1 INTEGER,
+ tnVlanDbMemTagPort2 INTEGER,
+ tnVlanDbMemTagPort3 INTEGER,
+ tnVlanDbMemTagPort4 INTEGER,
+ tnVlanDbMemTagPort5 INTEGER,
+ tnVlanDbMemTagPort6 INTEGER,
+ tnVlanDbMemTagPort7 INTEGER,
+ tnVlanDbMemTagPort8 INTEGER,
+ tnVlanDbMemTagPort9 INTEGER,
+ tnVlanDbMemTagPort10 INTEGER,
+ tnVlanDbRowStatus RowStatus
+ }
+
+tnVlanDbVID OBJECT-TYPE
+ SYNTAX VlanIndex
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION "The VLAN ID of the entry."
+ ::= { tnVLANDbEntry 1 }
+
+tnVlanDbFID OBJECT-TYPE
+ SYNTAX INTEGER (0..255)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION "The Forwarding Database number for this VLAN."
+ ::= { tnVLANDbEntry 2 }
+
+tnVlanDbVIDPriOverride OBJECT-TYPE
+ SYNTAX INTEGER { enable(1), disable(2) }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "Override Priority on frames assosicated with this VID."
+ ::= { tnVLANDbEntry 3 }
+
+tnVlanDbVIDPriority OBJECT-TYPE
+ SYNTAX INTEGER
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "Priority for frames assosicated with this VID."
+ ::= { tnVLANDbEntry 4 }
+
+tnVlanDbMemTagPort1 OBJECT-TYPE
+ SYNTAX INTEGER { memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5) }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "Membership and Egress Tagging on Logical Port 1.
+ memEgressNoMode(1)- Port 1 is a member of this VLAN and frames
+ that egress are unmodified.
+ memEgressNoTag(2) - Port 1 is a member of this VLAN and frames
+ that egress are untagged.
+ memEgressTag(3) - Port 1 is a member of this VLAN and frames
+ that egress are tagged.
+ notMember(4) - Port 1 is not a member of this VLAN and frames
+ that ingress with this VID are discarded.
+ notApplicable(5) is returned if there is no valid port."
+
+ ::= { tnVLANDbEntry 5 }
+
+tnVlanDbMemTagPort2 OBJECT-TYPE
+ SYNTAX INTEGER { memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5) }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "Membership and Egress Tagging on Logical Port 2.
+ memEgressNoMode(1)- Port 2 is a member of this VLAN and frames
+ that egress are unmodified.
+ memEgressNoTag(2) - Port 2 is a member of this VLAN and frames
+ that egress are untagged.
+ memEgressTag(3) - Port 2 is a member of this VLAN and frames
+ that egress are tagged.
+ notMember(4) - Port 2 is not a member of this VLAN and frames
+ that ingress with this VID are discarded.
+ notApplicable(5) is returned if there is no valid port."
+
+ ::= { tnVLANDbEntry 6 }
+
+tnVlanDbMemTagPort3 OBJECT-TYPE
+ SYNTAX INTEGER { memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5) }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "Membership and Egress Tagging on Logical Port 3.
+ memEgressNoMode(1)- Port 3 is a member of this VLAN and frames
+ that egress are unmodified.
+ memEgressNoTag(2) - Port 3 is a member of this VLAN and frames
+ that egress are untagged.
+ memEgressTag(3) - Port 3 is a member of this VLAN and frames
+ that egress are tagged.
+ notMember(4) - Port 3 is not a member of this VLAN and frames
+ that ingress with this VID are discarded.
+ notApplicable(5) is returned if there is no valid port."
+
+ ::= { tnVLANDbEntry 7 }
+
+tnVlanDbMemTagPort4 OBJECT-TYPE
+ SYNTAX INTEGER { memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5) }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "Membership and Egress Tagging on Logical Port 4.
+ memEgressNoMode(1)- Port 4 is a member of this VLAN and frames
+ that egress are unmodified.
+ memEgressNoTag(2) - Port 4 is a member of this VLAN and frames
+ that egress are untagged.
+ memEgressTag(3) - Port 4 is a member of this VLAN and frames
+ that egress are tagged.
+ notMember(4) - Port 4 is not a member of this VLAN and frames
+ that ingress with this VID are discarded.
+ notApplicable(5) is returned if there is no valid port."
+
+ ::= { tnVLANDbEntry 8 }
+
+tnVlanDbMemTagPort5 OBJECT-TYPE
+ SYNTAX INTEGER { memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5) }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "Membership and Egress Tagging on Logical Port 5.
+ memEgressNoMode(1)- Port 5 is a member of this VLAN and frames
+ that egress are unmodified.
+ memEgressNoTag(2) - Port 5 is a member of this VLAN and frames
+ that egress are untagged.
+ memEgressTag(3) - Port 5 is a member of this VLAN and frames
+ that egress are tagged.
+ notMember(4) - Port 5 is not a member of this VLAN and frames
+ that ingress with this VID are discarded.
+ notApplicable(5) is returned if there is no valid port."
+
+ ::= { tnVLANDbEntry 9 }
+
+tnVlanDbMemTagPort6 OBJECT-TYPE
+ SYNTAX INTEGER { memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5) }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "Membership and Egress Tagging on Logical Port 6.
+ memEgressNoMode(1)- Port 6 is a member of this VLAN and frames
+ that egress are unmodified.
+ memEgressNoTag(2) - Port 6 is a member of this VLAN and frames
+ that egress are untagged.
+ memEgressTag(3) - Port 6 is a member of this VLAN and frames
+ that egress are tagged.
+ notMember(4) - Port 6 is not a member of this VLAN and frames
+ that ingress with this VID are discarded.
+ notApplicable(5) is returned if there is no valid port."
+
+ ::= { tnVLANDbEntry 10 }
+
+tnVlanDbMemTagPort7 OBJECT-TYPE
+ SYNTAX INTEGER { memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5) }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "Membership and Egress Tagging on Logical Port 7.
+ memEgressNoMode(1)- Port 7 is a member of this VLAN and frames
+ that egress are unmodified.
+ memEgressNoTag(2) - Port 7 is a member of this VLAN and frames
+ that egress are untagged.
+ memEgressTag(3) - Port 7 is a member of this VLAN and frames
+ that egress are tagged.
+ notMember(4) - Port 7 is not a member of this VLAN and frames
+ that ingress with this VID are discarded.
+ notApplicable(5) is returned if there is no valid port."
+
+ ::= { tnVLANDbEntry 11 }
+
+tnVlanDbMemTagPort8 OBJECT-TYPE
+ SYNTAX INTEGER { memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5) }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "Membership and Egress Tagging on Logical Port 8.
+ memEgressNoMode(1)- Port 8 is a member of this VLAN and frames
+ that egress are unmodified.
+ memEgressNoTag(2) - Port 8 is a member of this VLAN and frames
+ that egress are untagged.
+ memEgressTag(3) - Port 8 is a member of this VLAN and frames
+ that egress are tagged.
+ notMember(4) - Port 8 is not a member of this VLAN and frames
+ that ingress with this VID are discarded.
+ notApplicable(5) is returned if there is no valid port."
+
+ ::= { tnVLANDbEntry 12 }
+
+tnVlanDbMemTagPort9 OBJECT-TYPE
+ SYNTAX INTEGER { memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5) }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "Membership and Egress Tagging on Logical Port 9.
+ memEgressNoMode(1)- Port 9 is a member of this VLAN and frames
+ that egress are unmodified.
+ memEgressNoTag(2) - Port 9 is a member of this VLAN and frames
+ that egress are untagged.
+ memEgressTag(3) - Port 9 is a member of this VLAN and frames
+ that egress are tagged.
+ notMember(4) - Port 9 is not a member of this VLAN and frames
+ that ingress with this VID are discarded.
+ notApplicable(5) is returned if there is no valid port."
+
+ ::= { tnVLANDbEntry 13 }
+
+tnVlanDbMemTagPort10 OBJECT-TYPE
+ SYNTAX INTEGER { memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5) }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "Membership and Egress Tagging on Logical Port 10.
+ memEgressNoMode(1)- Port 10 is a member of this VLAN and frames
+ that egress are unmodified.
+ memEgressNoTag(2) - Port 10 is a member of this VLAN and frames
+ that egress are untagged.
+ memEgressTag(3) - Port 10 is a member of this VLAN and frames
+ that egress are tagged.
+ notMember(4) - Port 10 is not a member of this VLAN and frames
+ that ingress with this VID are discarded.
+ notApplicable(5) is returned if there is no valid port."
+
+ ::= { tnVLANDbEntry 14 }
+
+tnVlanDbRowStatus OBJECT-TYPE
+ SYNTAX RowStatus
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "The status of this VLAN entry in the VLAN database."
+
+ ::= { tnVLANDbEntry 15 }
+
+tnVLANDbFlush OBJECT IDENTIFIER ::= { tnVlanDbMgmt 2 }
+
+tnVLANDbFlushOperation OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ doNothing(1),
+ flushAll(2)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION "Set this viarable to:
+ flushAll(2): flush all VLAN entries except default VLAN 1.
+ This variable can't be set if the 'tnVLANDbFlushOperationStatus'
+ is 'inProgress(4)'.
+ Do getting to this variable:
+ If an operation is being processed, the operation being processed is returned.
+ If no operation is being processed, 'doNothing(1)' is returned."
+ ::= { tnVLANDbFlush 1 }
+
+tnVLANDbFlushOperationStatus OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ unknown(1),
+ success(2),
+ failure(3),
+ inProgress(4)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION "The VLAN database flush operation status.
+ unknown(1): no flush operation has been performed.
+ success(2)/failure(3): the last flush operation is finished, success(2)
+ indicates the last flush operation is successful. failure(3)
+ indicates the last flush operation fails.
+ inProgress(4): flush operation is in progress."
+ ::= { tnVLANDbFlush 2 }
+
+tnVLANDbFlushOperationFailureReason OBJECT-TYPE
+ SYNTAX DisplayString (SIZE (0..63))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION "Specifies the description of the cause of 'failure(3)' state of the
+ object 'tnVLANDbFlushOperationStatus'. This object would be a null
+ string if value of 'tnVLANDbFlushOperationStatus' is anything other
+ than 'failure(3)'."
+ ::= { tnVLANDbFlush 3 }
+
+--
+-- Forwarding database
+--
+tnFIDDbTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnFIDDbEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION "The forwarding/filtering address database for this device."
+ ::= { tnFIDDbMgmt 1 }
+
+tnFIDDbEntry OBJECT-TYPE
+ SYNTAX TnFIDDbEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION "Information about a particular MAC address."
+ INDEX { tnFIDDbID, tnFIDDbMacAddress }
+ ::= { tnFIDDbTable 1 }
+
+TnFIDDbEntry ::=
+ SEQUENCE {
+ tnFIDDbID INTEGER,
+ tnFIDDbMacAddress MacAddress,
+ tnFIDDbConnPort INTEGER,
+ tnFIDDbPriority INTEGER,
+ tnFIDDbEntryType INTEGER,
+ tnFIDDbEntryStatus RowStatus
+ }
+
+tnFIDDbID OBJECT-TYPE
+ SYNTAX INTEGER (0..255)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION "The Forwarding Database Number. This identifies the database."
+ ::= { tnFIDDbEntry 2 }
+
+tnFIDDbMacAddress OBJECT-TYPE
+ SYNTAX MacAddress
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION "The unicast or multicast MAC address that the device has forwarding information."
+ ::= { tnFIDDbEntry 3 }
+
+tnFIDDbConnPort OBJECT-TYPE
+ SYNTAX INTEGER
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "The index of the logical Port from which the device received the 'tnFIDDbMacAddress'."
+ ::= { tnFIDDbEntry 4 }
+
+tnFIDDbPriority OBJECT-TYPE
+ SYNTAX INTEGER
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "The priority of this MAC entry."
+ ::= { tnFIDDbEntry 5 }
+
+tnFIDDbEntryType OBJECT-TYPE
+ SYNTAX INTEGER { static(1), staticNRL(2), staticPA(3), dynamic(4) }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "The Entry state of this unicast or multicast entry.
+ The types represent :
+ static(1) - A Valid entry that doesnot age.
+ staticNRL(2) - A static entry that has no ingress rate limiting.
+ staticPA(3) - A static entry that has priority override enabled.
+ dynamic(4) - A valid entry with no special attributes which
+ ages and finally removed from the database.
+
+ A unicast entry can be static(1) or staticPA(3) but not
+ staticNRL(2). For MAC address which are learned, the read-only value
+ of dynamic(4) is returned."
+ ::= { tnFIDDbEntry 6 }
+
+tnFIDDbEntryStatus OBJECT-TYPE
+ SYNTAX RowStatus
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION "The status of this entry."
+ ::= { tnFIDDbEntry 7 }
+
+tnFIDDbFlush OBJECT IDENTIFIER ::= { tnFIDDbMgmt 2 }
+
+tnFIDDbFlushFID OBJECT-TYPE
+ SYNTAX INTEGER(0..4094)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION "When 'tnFIDDbFlushOperation' is 'flushAllFID(3)' or 'flushAllDynamicFID(4)',
+ the value(1..4094) of this viarable is used to specify the FID to be flushed.
+ The value 0 of this virable means no FID is specified."
+ ::= { tnFIDDbFlush 1 }
+
+tnFIDDbFlushOperation OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ doNothing(1),
+ flushAll(2),
+ flushAllDynamic(3),
+ flushAllFID(4),
+ flushAllDynamicFID(5)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION "Set this viarable to:
+ flushAll(2): flush all FID entries for all FIDs.
+ flushAllDynamic(3): flush all FID dynamic entries for all FIDs.
+ flushAllFID(4): flush all FID entries for one FID which is specified
+ by ionFIDDbFlushFID.
+ flushAllDynamicFID(5): flush all FID dynamic entries for one FID which
+ is specified by ionFIDDbFlushFID.
+ This variable can't be set if the 'ionFIDDbFlushOperationStatus'
+ is 'inProgress(4)'.
+ Do getting to this variable:
+ If an operation is being processed, the operation being processed is returned.
+ If no operation is being processed, 'doNothing(1)' is returned."
+ ::= { tnFIDDbFlush 2 }
+
+tnFIDDbFlushOperationStatus OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ unknown(1),
+ success(2),
+ failure(3),
+ inProgress(4)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION "The FID database flush operation status.
+ unknown(1): no flush operation has been performed.
+ success(2)/failure(3): the last flush operation is finished, success(2)
+ indicates the last flush operation is successful. failure(3)
+ indicates the last flush operation fails.
+ inProgress(4): flush operation is in progress."
+ ::= { tnFIDDbFlush 3 }
+
+tnFIDDbFlushOperationFailureReason OBJECT-TYPE
+ SYNTAX DisplayString (SIZE (0..63))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION "Specifies the description of the cause of 'failure(3)' state of the
+ object 'ionFIDDbFlushOperationStatus'. This object would be a null
+ string if value of 'ionFIDDbFlushOperationStatus' is anything other
+ than 'failure(3)'."
+ ::= { tnFIDDbFlush 4 }
+
+--
+-- VLAN Control List
+--
+tnVclMacBasedMgmt OBJECT IDENTIFIER ::= { tnVclMgmt 1 }
+tnVclProtoBasedMgmt OBJECT IDENTIFIER ::= { tnVclMgmt 2 }
+tnVclIpSubnetBasedMgmt OBJECT IDENTIFIER ::= { tnVclMgmt 3 }
+
+--
+-- Mac based Vlan
+--
+tnVclMacBasedTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnVclMacBasedEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table is used to control MAC based Vlan functions."
+ ::= { tnVclMacBasedMgmt 1 }
+
+tnVclMacBasedEntry OBJECT-TYPE
+ SYNTAX TnVclMacBasedEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A entry in the table is used to control MAC based Vlan functions."
+ INDEX { tnVclMacBasedMacAddr }
+ ::= { tnVclMacBasedTable 1 }
+
+TnVclMacBasedEntry ::=
+ SEQUENCE
+ {
+ tnVclMacBasedMacAddr MacAddress,
+ tnVclMacBasedVlanId VlanIndex,
+ tnVclMacBasedPortMember PortList,
+ tnVclMacBasedUser INTEGER,
+ tnVclMacBasedRowStatus RowStatus
+ }
+
+tnVclMacBasedMacAddr OBJECT-TYPE
+ SYNTAX MacAddress
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "The MAC address is used for the MAC based VLAN function classification key."
+ ::= { tnVclMacBasedEntry 1 }
+
+tnVclMacBasedVlanId OBJECT-TYPE
+ SYNTAX VlanIndex
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "The Vlan Id will be assigned to the incoming frame(if needed) which matches this specific MAC address and port member list."
+ ::= { tnVclMacBasedEntry 2 }
+
+tnVclMacBasedPortMember OBJECT-TYPE
+ SYNTAX PortList
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "The member port list of this specific MAC based Vlan match process takes place."
+ ::= { tnVclMacBasedEntry 3 }
+
+tnVclMacBasedUser OBJECT-TYPE
+ SYNTAX INTEGER{
+ static(1),
+ nas(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The creater of this entry. The MAC based VLAN entry is either created by user configuration(static), or by NAS dynamic creation(nas)."
+ ::= { tnVclMacBasedEntry 4 }
+
+tnVclMacBasedRowStatus OBJECT-TYPE
+ SYNTAX RowStatus
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "The status of this entry."
+ ::= { tnVclMacBasedEntry 5 }
+
+--
+-- Protocol Based Vlan
+--
+tnVclProtoBasedGroupMapTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnVclProtoBasedGroupMapEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table is used to build a specific protocol group for VCL match process."
+ ::= { tnVclProtoBasedMgmt 1 }
+
+tnVclProtoBasedGroupMapEntry OBJECT-TYPE
+ SYNTAX TnVclProtoBasedGroupMapEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A entry in this table is used to build a specific protocol group for VCL match process."
+-- INDEX { IMPLIED tnVclProtoBasedGroupMapName }
+ INDEX { tnVclProtoBasedGroupMapName }
+ ::= { tnVclProtoBasedGroupMapTable 1 }
+
+TnVclProtoBasedGroupMapEntry ::=
+ SEQUENCE
+ {
+ tnVclProtoBasedGroupMapName SnmpAdminString,
+ tnVclProtoBasedGroupMapProtocol INTEGER,
+ tnVclProtoBasedGroupMapEtherTypeVal INTEGER,
+ tnVclProtoBasedGroupMapSnapOui EightOTwoOui,
+ tnVclProtoBasedGroupMapSnapPid INTEGER,
+ tnVclProtoBasedGroupMapLlcDsap INTEGER,
+ tnVclProtoBasedGroupMapLlcSsap INTEGER,
+ tnVclProtoBasedGroupMapRowStatus RowStatus
+ }
+
+tnVclProtoBasedGroupMapName OBJECT-TYPE
+ SYNTAX SnmpAdminString
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "The locally arbitrary, but unique identifier associated with this TnVclProtoBasedGroupMapEntry."
+ ::= { tnVclProtoBasedGroupMapEntry 1 }
+
+tnVclProtoBasedGroupMapProtocol OBJECT-TYPE
+ SYNTAX INTEGER{
+ ethernet(1),
+ snap(2),
+ llc(3)
+ }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "Frame Type can have one of the following values:
+ 1. Ethernet
+ 2. SNAP
+ 3. LLC"
+ ::= { tnVclProtoBasedGroupMapEntry 2 }
+
+tnVclProtoBasedGroupMapEtherTypeVal OBJECT-TYPE
+ SYNTAX INTEGER(1536..65535)
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "Ethernet Type is valid only if the tnVclProtoBasedGroupMapProtocol is ethernet(1). Valid values for etype ranges is from 0x0600-0xffff.
+ If tnVclProtoBasedGroupMapProtocol is not ethernet(1), this value will be 0xffff instead."
+ ::= { tnVclProtoBasedGroupMapEntry 3 }
+
+tnVclProtoBasedGroupMapSnapOui OBJECT-TYPE
+ SYNTAX EightOTwoOui
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "SNAP OUI is valid only if the tnVclProtoBasedGroupMapProtocol is snap(2). OUI (Organizationally Unique Identifier) is value in
+ format of xx-xx-xx where each pair (xx) in string is a hexadecimal value ranges from 0x00-0xff.
+ If tnVclProtoBasedGroupMapProtocol is not snap(2), this value will be FF-FF-FF instead."
+ ::= { tnVclProtoBasedGroupMapEntry 4 }
+
+tnVclProtoBasedGroupMapSnapPid OBJECT-TYPE
+ SYNTAX INTEGER
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "SNAP PID is valid only if the tnVclProtoBasedGroupMapProtocol is snap(2).
+ If the OUI is hexadecimal 000000, the protocol ID is the Ethernet type (EtherType) field value for the protocol running on top of SNAP;
+ if the OUI is an OUI for a particular organization, the protocol ID is a value assigned by that organization to the protocol
+ running on top of SNAP.
+ In other words, if value of OUI field is 00-00-00 then value of PID will be etype (0x0600-0xffff) and
+ if value of OUI is other than 00-00-00 then valid value of PID will be any value from 0x0000 to 0xffff.
+ If tnVclProtoBasedGroupMapProtocol is not snap(2), this value will be 0xffff instead."
+ ::= { tnVclProtoBasedGroupMapEntry 5 }
+
+tnVclProtoBasedGroupMapLlcDsap OBJECT-TYPE
+ SYNTAX INTEGER
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "LLC DSAP is valid only if the tnVclProtoBasedGroupMapProtocol is llc(3).
+ DSAP: 1-byte long string (0x00-0xff).
+ If tnVclProtoBasedGroupMapProtocol is not llc(3), this value will be 0xff instead."
+ ::= { tnVclProtoBasedGroupMapEntry 6 }
+
+tnVclProtoBasedGroupMapLlcSsap OBJECT-TYPE
+ SYNTAX INTEGER
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "LLC SSAP is valid only if the tnVclProtoBasedGroupMapProtocol is llc(3).
+ SSAP: 1-byte long string (0x00-0xff).
+ If tnVclProtoBasedGroupMapProtocol is not llc(3), this value will be 0xff instead."
+ ::= { tnVclProtoBasedGroupMapEntry 7 }
+
+tnVclProtoBasedGroupMapRowStatus OBJECT-TYPE
+ SYNTAX RowStatus
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "The status of this entry."
+ ::= { tnVclProtoBasedGroupMapEntry 8 }
+
+--
+--
+tnVclProtoBasedVlanMapTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnVclProtoBasedVlanMapEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "The table is used to associate the protocol based VLAN groups with VLAN paramaters."
+ ::= { tnVclProtoBasedMgmt 2 }
+
+tnVclProtoBasedVlanMapEntry OBJECT-TYPE
+ SYNTAX TnVclProtoBasedVlanMapEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A entry in this table is used to associate the protocol based VLAN groups with VLAN paramaters."
+ INDEX { IMPLIED tnVclProtoBasedGroupMapName, tnVclProtoBasedVlanMapVlanId }
+ ::= { tnVclProtoBasedVlanMapTable 1 }
+
+TnVclProtoBasedVlanMapEntry ::=
+ SEQUENCE
+ {
+ tnVclProtoBasedVlanMapVlanId VlanIndex,
+ tnVclProtoBasedVlanMapPortMember PortList,
+ tnVclProtoBasedVlanMapRowStatus RowStatus
+ }
+
+tnVclProtoBasedVlanMapVlanId OBJECT-TYPE
+ SYNTAX VlanIndex
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "The Vlan Id will be assigned to the incoming frame(if needed) which matches this specific Protocol Group and port member list."
+ ::= { tnVclProtoBasedVlanMapEntry 1 }
+
+tnVclProtoBasedVlanMapPortMember OBJECT-TYPE
+ SYNTAX PortList
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "The member port list of this specific Protocol based Vlan match process takes place."
+ ::= { tnVclProtoBasedVlanMapEntry 2 }
+
+tnVclProtoBasedVlanMapRowStatus OBJECT-TYPE
+ SYNTAX RowStatus
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "The status of this entry."
+ ::= { tnVclProtoBasedVlanMapEntry 3 }
+
+--
+-- IP subnet based Vlan
+--
+tnVclIpSubnetBasedTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF TnVclIpSubnetBasedEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This Table is used to control IP subnet based VLAN functions."
+ ::= { tnVclIpSubnetBasedMgmt 1 }
+
+tnVclIpSubnetBasedEntry OBJECT-TYPE
+ SYNTAX TnVclIpSubnetBasedEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A entry in this table is used to control IP subnet based VLAN functions."
+ INDEX { tnVclIpSubnetBasedVceId }
+ ::= { tnVclIpSubnetBasedTable 1 }
+
+TnVclIpSubnetBasedEntry ::=
+ SEQUENCE
+ {
+ tnVclIpSubnetBasedVceId INTEGER,
+ tnVclIpSubnetBasedIpAddr IpAddress,
+ tnVclIpSubnetBasedMaskLen INTEGER,
+ tnVclIpSubnetBasedVlanId VlanIndex,
+ tnVclIpSubnetBasedPortMember PortList,
+ tnVclIpSubnetBasedRowStatus RowStatus
+ }
+
+tnVclIpSubnetBasedVceId OBJECT-TYPE
+ SYNTAX INTEGER (1..11111) -- range added by Jing
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Indicates the index of the entry. The valid range is implement specific.
+ If VCE ID is 0, application will auto-generate the VCE ID for that entry."
+ ::= { tnVclIpSubnetBasedEntry 1 }
+
+tnVclIpSubnetBasedIpAddr OBJECT-TYPE
+ SYNTAX IpAddress
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "Indicates the IP address for match process."
+ ::= { tnVclIpSubnetBasedEntry 2 }
+
+tnVclIpSubnetBasedMaskLen OBJECT-TYPE
+ SYNTAX INTEGER
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "Indicates the network mask length."
+ ::= { tnVclIpSubnetBasedEntry 3 }
+
+tnVclIpSubnetBasedVlanId OBJECT-TYPE
+ SYNTAX VlanIndex
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "The Vlan Id will be assigned to the incoming frame(if needed) which matches this specific IP subnet and port member list."
+ ::= { tnVclIpSubnetBasedEntry 4 }
+
+tnVclIpSubnetBasedPortMember OBJECT-TYPE
+ SYNTAX PortList
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "The member port list of this specific IP subnet based Vlan match process takes place."
+ ::= { tnVclIpSubnetBasedEntry 5 }
+
+tnVclIpSubnetBasedRowStatus OBJECT-TYPE
+ SYNTAX RowStatus
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "The status of this entry."
+ ::= { tnVclIpSubnetBasedEntry 6 }
+
+--
+-- NOTIFICATIONS FOR THIS MIB
+--
+
+tnIfSourceAddrChangeEvt NOTIFICATION-TYPE
+ OBJECTS {
+ tnFIDDbMacAddress, tnFIDDbConnPort
+ }
+ STATUS current
+ DESCRIPTION
+ "A tnIfSourceAddrChangeEvt event is sent when the tnIfSourceAddrLock is set to 'true',
+ the ionIfSourceAddrLockAction is set to 'discardAndNotify' or 'all' and there is an
+ intrusion/SA change on this port."
+ ::= { tnVlanQoSMgmtNotifications 1 }
+
+END
|