diff options
Diffstat (limited to 'MIBS/junos/OPT-IF-MIB')
| -rw-r--r-- | MIBS/junos/OPT-IF-MIB | 6261 |
1 files changed, 6261 insertions, 0 deletions
diff --git a/MIBS/junos/OPT-IF-MIB b/MIBS/junos/OPT-IF-MIB new file mode 100644 index 0000000..b9e0d31 --- /dev/null +++ b/MIBS/junos/OPT-IF-MIB @@ -0,0 +1,6261 @@ +OPT-IF-MIB DEFINITIONS ::= BEGIN + +IMPORTS + MODULE-IDENTITY, OBJECT-TYPE, Gauge32, Integer32, + Unsigned32, transmission + FROM SNMPv2-SMI + TEXTUAL-CONVENTION, RowPointer, RowStatus, TruthValue + FROM SNMPv2-TC + SnmpAdminString + FROM SNMP-FRAMEWORK-MIB + MODULE-COMPLIANCE, OBJECT-GROUP + FROM SNMPv2-CONF + ifIndex + FROM IF-MIB; + +-- This is the MIB module for the OTN Interface objects. + +optIfMibModule MODULE-IDENTITY + LAST-UPDATED "200308130000Z" + ORGANIZATION "IETF AToM MIB Working Group" + CONTACT-INFO + "WG charter: + http://www.ietf.org/html.charters/atommib-charter.html + + Mailing Lists: + General Discussion: atommib@research.telcordia.com + To Subscribe: atommib-request@research.telcordia.com + Editor: Hing-Kam Lam + Postal: Lucent Technologies, Room 4C-616 + 101 Crawfords Corner Road + Holmdel, NJ 07733 + Tel: +1 732 949 8338 + Email: hklam@lucent.com" + DESCRIPTION + "The MIB module to describe pre-OTN and OTN interfaces. + + Copyright (C) The Internet Society (2003). This version + of this MIB module is part of RFC 3591; see the RFC + itself for full legal notices." + REVISION "200308130000Z" + DESCRIPTION + "Initial version, published as RFC 3591." + ::={ transmission 133 } + +-- textual conventions + +OptIfAcTI ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "The trace identifier (TI) accepted at the receiver." + SYNTAX OCTET STRING (SIZE(64)) + +OptIfBitRateK ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "Indicates the index 'k' that is used to + represent a supported bit rate and the different + versions of OPUk, ODUk and OTUk. + Allowed values of k are defined in ITU-T G.709. + Currently allowed values in G.709 are: + k=1 represents an approximate bit rate of 2.5 Gbit/s, + k=2 represents an approximate bit rate of 10 Gbit/s, + k=3 represents an approximate bit rate of 40 Gbit/s." + SYNTAX Integer32 + +OptIfDEGM ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "Indicates the threshold level for declaring a Degraded Signal + defect (dDEG). A dDEG shall be declared if OptIfDEGM + consecutive bad PM Seconds are detected." + SYNTAX Unsigned32 (2..10) + +OptIfDEGThr ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "Indicates the threshold level for declaring a performance + monitoring (PM) Second to be bad. A PM Second is declared bad if + the percentage of detected errored blocks in that second is + greater than or equal to OptIfDEGThr." + SYNTAX Unsigned32 (1..100) + +OptIfDirectionality ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "Indicates the directionality of an entity." + SYNTAX INTEGER { + sink(1), + source(2), + bidirectional(3) + } + +OptIfSinkOrSource ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "Indicates the directionality of an entity + that is allowed only to be a source or sink." + SYNTAX INTEGER { + sink(1), + source(2) + } + +OptIfExDAPI ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "The Destination Access Point Identifier (DAPI) + expected by the receiver." + SYNTAX OCTET STRING (SIZE(16)) + +OptIfExSAPI ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "The Source Access Point Identifier (SAPI) + expected by the receiver." + SYNTAX OCTET STRING (SIZE(16)) + +OptIfIntervalNumber ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "Uniquely identifies a 15-minute interval. The interval + identified by 1 is the most recently completed interval, and + the interval identified by n is the interval immediately + preceding the one identified by n-1." + SYNTAX Unsigned32 (1..96) + +OptIfTIMDetMode ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "Indicates the mode of the Trace Identifier Mismatch (TIM) + Detection function." + SYNTAX INTEGER { + off(1), + dapi(2), + sapi(3), + both(4) + } + +OptIfTxTI ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "The trace identifier (TI) transmitted." + SYNTAX OCTET STRING (SIZE(64)) + +-- object groups + +optIfObjects OBJECT IDENTIFIER ::= { optIfMibModule 1 } +optIfConfs OBJECT IDENTIFIER ::= { optIfMibModule 2 } + +optIfOTMn OBJECT IDENTIFIER ::= { optIfObjects 1 } +optIfPerfMon OBJECT IDENTIFIER ::= { optIfObjects 2 } +optIfOTSn OBJECT IDENTIFIER ::= { optIfObjects 3 } +optIfOMSn OBJECT IDENTIFIER ::= { optIfObjects 4 } +optIfOChGroup OBJECT IDENTIFIER ::= { optIfObjects 5 } +optIfOCh OBJECT IDENTIFIER ::= { optIfObjects 6 } + +optIfOTUk OBJECT IDENTIFIER ::= { optIfObjects 7 } +optIfODUk OBJECT IDENTIFIER ::= { optIfObjects 8 } +optIfODUkT OBJECT IDENTIFIER ::= { optIfObjects 9 } + +optIfGroups OBJECT IDENTIFIER ::= { optIfConfs 1 } +optIfCompl OBJECT IDENTIFIER ::= { optIfConfs 2 } + +-- the optIfOTMn group +-- This group defines the OTM structure information of an +-- optical interface. + +-- OTMn Table + +optIfOTMnTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOTMnEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OTMn structure information." + ::= { optIfOTMn 1 } + +optIfOTMnEntry OBJECT-TYPE + SYNTAX OptIfOTMnEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains the OTMn structure + information of an optical interface." + INDEX { ifIndex } + ::= { optIfOTMnTable 1 } + +OptIfOTMnEntry ::= + SEQUENCE { + optIfOTMnOrder Unsigned32, + optIfOTMnReduced TruthValue, + optIfOTMnBitRates BITS, + optIfOTMnInterfaceType SnmpAdminString, + optIfOTMnTcmMax Unsigned32, + optIfOTMnOpticalReach INTEGER + } + +optIfOTMnOrder OBJECT-TYPE + SYNTAX Unsigned32 (1..900) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates the order of the OTM, which + represents the maximum number of wavelengths that can be + supported at the bit rate(s) supported on the interface." + ::= { optIfOTMnEntry 1 } + +optIfOTMnReduced OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates whether a reduced or full + functionality is supported at the interface. A value of + true means reduced. A value of false means full." + ::= { optIfOTMnEntry 2 } + +optIfOTMnBitRates OBJECT-TYPE + SYNTAX BITS { bitRateK1(0), bitRateK2(1), bitRateK3(2) } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This attribute is a bit map representing the bit + rate or set of bit rates supported on the interface. + The meaning of each bit position is as follows: + bitRateK1(0) is set if the 2.5 Gbit/s rate is supported + bitRateK2(1) is set if the 10 Gbit/s rate is supported + bitRateK3(2) is set if the 40 Gbit/s rate is supported + Note that each bit position corresponds to one possible + value of the type OptIfBitRateK. + The default value of this attribute is system specific." + ::= { optIfOTMnEntry 3 } + +optIfOTMnInterfaceType OBJECT-TYPE + SYNTAX SnmpAdminString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object identifies the type of interface. The value of + this attribute will affect the behavior of the OTM with + respect to presence/absence of OTM Overhead Signal (OOS) + processing and TCM activation. For an IrDI interface, + there is no OOS processing and TCM activation is limited + to n levels as specified by a TCM level threshold. + + This object contains two fields that are separated by + whitespace. The possible values are: + field 1: one of the 4-character ASCII strings + 'IrDI' or 'IaDI' + field 2: free-form text consisting of printable + UTF-8 encoded characters + + Note that field 2 is optional. If it is not present then there + is no requirement for trailing whitespace after field 1. + + The default values are as follows: + field 1: 'IaDI' + field 2: an empty string." + + ::= { optIfOTMnEntry 4 } + +optIfOTMnTcmMax OBJECT-TYPE + SYNTAX Unsigned32 (0..6) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This object identifies the maximum number of TCM + levels allowed for any Optical Channel contained + in this OTM. A new TCM activation will be rejected + if the requested level is greater than the threshold. + If InterfaceType object specifies a type of 'IaDI' + for this OTM, then this attribute is irrelevant. + + Possible values: unsigned integers in the range + from 0 to 6 inclusive. + Default value: 3." + + ::= { optIfOTMnEntry 5 } + +optIfOTMnOpticalReach OBJECT-TYPE + SYNTAX INTEGER { intraOffice(1), shortHaul(2), longHaul(3), + veryLongHaul(4), ultraLongHaul(5) } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates the length the optical signal + may travel before requiring termination or regeneration. + The meaning of the enumeration are: + intraOffice(1) - intra-office (as defined in ITU-T G.957) + shortHaul(2) - short haul (as defined in ITU-T G.957) + longHaul(3) - long haul (as defined in ITU-T G.957) + veryLongHaul(4) - very long haul (as defined in ITU-T G.691) + ultraLongHaul(5)- ultra long haul (as defined in ITU-T G.691)" + ::= { optIfOTMnEntry 6 } + +-- the optIfPerfMon group +-- This group defines performance monitoring objects for all +-- layers. + +-- PM interval table + +optIfPerfMonIntervalTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfPerfMonIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of 15-minute performance monitoring interval + information." + ::= { optIfPerfMon 1 } + +optIfPerfMonIntervalEntry OBJECT-TYPE + SYNTAX OptIfPerfMonIntervalEntry + MAX-ACCESS not-accessible + STATUS current + + DESCRIPTION + "A conceptual row that contains 15-minute performance + monitoring interval information of an interface." + INDEX { ifIndex } + ::= { optIfPerfMonIntervalTable 1 } + +OptIfPerfMonIntervalEntry ::= + SEQUENCE { + optIfPerfMonCurrentTimeElapsed Gauge32, + optIfPerfMonCurDayTimeElapsed Gauge32, + optIfPerfMonIntervalNumIntervals Unsigned32, + optIfPerfMonIntervalNumInvalidIntervals Unsigned32 + } + +optIfPerfMonCurrentTimeElapsed OBJECT-TYPE + SYNTAX Gauge32 (0..900) + UNITS "seconds" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of seconds elapsed in the current 15-minute + performance monitoring interval. + If, for some reason, such as an adjustment in the NE's + time-of-day clock, the number of seconds elapsed exceeds + the maximum value, then the maximum value will be returned." + ::= { optIfPerfMonIntervalEntry 1 } + +optIfPerfMonCurDayTimeElapsed OBJECT-TYPE + SYNTAX Gauge32 (0..86400) + UNITS "seconds" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of seconds elapsed in the current 24-hour interval + performance monitoring period. + If, for some reason, such as an adjustment in the NE's + time-of-day clock, the number of seconds elapsed exceeds + the maximum value, then the maximum value will be returned." + ::= { optIfPerfMonIntervalEntry 2 } + +optIfPerfMonIntervalNumIntervals OBJECT-TYPE + SYNTAX Unsigned32 (0..96) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of 15-minute intervals for which performance + monitoring data is available. The number is the same for all + the associated sub layers of the interface. + An optical interface must be capable of supporting at least + n intervals, where n is defined as follows: + The minimum value of n is 4. + The default of n is 32. + The maximum value of n is 96. + + The value of this object will be n unless performance + monitoring was (re-)started for the interface within the last + (n*15) minutes, in which case the value will be the number of + complete 15-minute intervals since measurement was + (re-)started." + ::= { optIfPerfMonIntervalEntry 3 } + +optIfPerfMonIntervalNumInvalidIntervals OBJECT-TYPE + SYNTAX Unsigned32 (0..96) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of intervals in the range from 0 to + optIfPerfMonIntervalNumIntervals for which no performance + monitoring data is available and/or the data is invalid." + ::= { optIfPerfMonIntervalEntry 4 } + +-- the optIfOTSn group +-- This group handles the configuration and performance +-- monitoring objects for OTS layers. + +-- OTSn config table + +optIfOTSnConfigTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOTSnConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OTSn configuration information." + ::= { optIfOTSn 1 } + +optIfOTSnConfigEntry OBJECT-TYPE + SYNTAX OptIfOTSnConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OTSn configuration + information of an interface." + INDEX { ifIndex } + ::= { optIfOTSnConfigTable 1 } + +OptIfOTSnConfigEntry ::= + SEQUENCE { + optIfOTSnDirectionality OptIfDirectionality, + optIfOTSnAprStatus SnmpAdminString, + optIfOTSnAprControl SnmpAdminString, + optIfOTSnTraceIdentifierTransmitted OptIfTxTI, + optIfOTSnDAPIExpected OptIfExDAPI, + optIfOTSnSAPIExpected OptIfExSAPI, + optIfOTSnTraceIdentifierAccepted OptIfAcTI, + optIfOTSnTIMDetMode OptIfTIMDetMode, + optIfOTSnTIMActEnabled TruthValue, + optIfOTSnCurrentStatus BITS + } + +optIfOTSnDirectionality OBJECT-TYPE + SYNTAX OptIfDirectionality + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the directionality of the entity." + ::= { optIfOTSnConfigEntry 1 } + +optIfOTSnAprStatus OBJECT-TYPE + SYNTAX SnmpAdminString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This attribute indicates the status of the Automatic + Power Reduction (APR) function of the entity. Valid + values are 'on' and 'off'." + ::= { optIfOTSnConfigEntry 2 } + +optIfOTSnAprControl OBJECT-TYPE + SYNTAX SnmpAdminString + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This object is a UTF-8 encoded string that specifies Automatic + Power Reduction (APR) control actions requested of this entity + (when written) and that returns the current APR control state + of this entity (when read). The values are implementation-defined. + Any implementation that instantiates this object must document the + set of values that it allows to be written, the set of values + that it will return, and what each of those values means." + ::= { optIfOTSnConfigEntry 3 } + +optIfOTSnTraceIdentifierTransmitted OBJECT-TYPE + SYNTAX OptIfTxTI + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The trace identifier transmitted. + This object is applicable when optIfOTSnDirectionality has the + value source(2) or bidirectional(3). + This object does not apply to reduced-capability systems (i.e., + those for which optIfOTMnReduced has the value true(1)) or + at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 + has the value 'IrDI'). + If no value is ever set by a management entity for the object + optIfOTSnTraceIdentifierTransmitted, system-specific default + value will be used. Any implementation that instantiates this + object must document the system-specific default value or how it + is derived." + ::= { optIfOTSnConfigEntry 4 } + +optIfOTSnDAPIExpected OBJECT-TYPE + SYNTAX OptIfExDAPI + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The DAPI expected by the receiver. + This object is applicable when optIfOTSnDirectionality has the + value sink(1) or bidirectional(3). It has no effect if + optIfOTSnTIMDetMode has the value off(1) or sapi(3). + This object does not apply to reduced-capability systems (i.e., + those for which optIfOTMnReduced has the value true(1)) or + at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 + has the value 'IrDI')." + ::= { optIfOTSnConfigEntry 5 } + +optIfOTSnSAPIExpected OBJECT-TYPE + SYNTAX OptIfExSAPI + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The SAPI expected by the receiver. + This object is applicable when optIfOTSnDirectionality has the + value sink(1) or bidirectional(3). It has no effect if + optIfOTSnTIMDetMode has the value off(1) or dapi(2). + This object does not apply to reduced-capability systems (i.e., + those for which optIfOTMnReduced has the value true(1)) or + at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 + has the value 'IrDI')." + ::= { optIfOTSnConfigEntry 6 } + +optIfOTSnTraceIdentifierAccepted OBJECT-TYPE + SYNTAX OptIfAcTI + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The actual trace identifier received. + This object is applicable when optIfOTSnDirectionality has the + value sink(1) or bidirectional(3). Its value is unspecified + if optIfOTSnCurrentStatus has either or both of the + losO(5) and los(6) bits set. + This object does not apply to reduced-capability systems (i.e., + those for which optIfOTMnReduced has the value true(1)) or + at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 + has the value 'IrDI')." + ::= { optIfOTSnConfigEntry 7 } + +optIfOTSnTIMDetMode OBJECT-TYPE + SYNTAX OptIfTIMDetMode + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Indicates the mode of the Trace Identifier Mismatch (TIM) + Detection function. This object is applicable + when optIfOTSnDirectionality has the value sink(1) + or bidirectional(3). The default value is off(1). + This object does not apply to reduced-capability systems (i.e., + those for which optIfOTMnReduced has the value true(1)) or + at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 + has the value 'IrDI'). + The default value of this object is off(1)." + ::= { optIfOTSnConfigEntry 8 } + +optIfOTSnTIMActEnabled OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Indicates whether the Trace Identifier Mismatch (TIM) + Consequent Action function is enabled. This object + is applicable when optIfOTSnDirectionality has the + value sink(1) or bidirectional(3). It has no effect + when the value of optIfOTSnTIMDetMode is off(1). + This object does not apply to reduced-capability systems (i.e., + those for which optIfOTMnReduced has the value true(1)) or + at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 + has the value 'IrDI'). + The default value of this object is false(2)." + ::= { optIfOTSnConfigEntry 9 } + +optIfOTSnCurrentStatus OBJECT-TYPE + SYNTAX BITS { + bdiP(0), + bdiO(1), + bdi(2), + tim(3), + losP(4), + losO(5), + los(6) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the defect condition of the entity, if any. + This object is applicable when optIfOTSnDirectionality + has the value sink(1) or bidirectional(3). In + reduced-capability systems or at IrDI interfaces + the only bit position that may be set is los(6)." + ::= { optIfOTSnConfigEntry 10 } + +-- OTSn sink current table +-- Contains data for the current 15-minute performance monitoring +-- interval. + +optIfOTSnSinkCurrentTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOTSnSinkCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OTSn sink performance monitoring information for + the current 15-minute interval." + ::= { optIfOTSn 2 } + +optIfOTSnSinkCurrentEntry OBJECT-TYPE + SYNTAX OptIfOTSnSinkCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OTSn sink performance + monitoring information of an interface for the current + 15-minute interval." + INDEX { ifIndex } + ::= { optIfOTSnSinkCurrentTable 1 } + +OptIfOTSnSinkCurrentEntry ::= + SEQUENCE { + optIfOTSnSinkCurrentSuspectedFlag TruthValue, + optIfOTSnSinkCurrentInputPower Integer32, + optIfOTSnSinkCurrentLowInputPower Integer32, + optIfOTSnSinkCurrentHighInputPower Integer32, + optIfOTSnSinkCurrentLowerInputPowerThreshold Integer32, + optIfOTSnSinkCurrentUpperInputPowerThreshold Integer32, + optIfOTSnSinkCurrentOutputPower Integer32, + optIfOTSnSinkCurrentLowOutputPower Integer32, + optIfOTSnSinkCurrentHighOutputPower Integer32, + optIfOTSnSinkCurrentLowerOutputPowerThreshold Integer32, + optIfOTSnSinkCurrentUpperOutputPowerThreshold Integer32 + } + +optIfOTSnSinkCurrentSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOTSnSinkCurrentEntry 1 } + +optIfOTSnSinkCurrentInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The optical power monitored at the input." + ::= { optIfOTSnSinkCurrentEntry 2 } + +optIfOTSnSinkCurrentLowInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the input during the + current 15-minute interval." + ::= { optIfOTSnSinkCurrentEntry 3 } + +optIfOTSnSinkCurrentHighInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the input during the + current 15-minute interval." + ::= { optIfOTSnSinkCurrentEntry 4 } + +optIfOTSnSinkCurrentLowerInputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The lower limit threshold on input power. If + optIfOTSnSinkCurrentInputPower drops to this value or below, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOTSnSinkCurrentEntry 5 } + +optIfOTSnSinkCurrentUpperInputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper limit threshold on input power. If + optIfOTSnSinkCurrentInputPower reaches or exceeds this value, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOTSnSinkCurrentEntry 6 } + +optIfOTSnSinkCurrentOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The optical power monitored at the output." + ::= { optIfOTSnSinkCurrentEntry 7 } + +optIfOTSnSinkCurrentLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + current 15-minute interval." + ::= { optIfOTSnSinkCurrentEntry 8 } + +optIfOTSnSinkCurrentHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + current 15-minute interval." + ::= { optIfOTSnSinkCurrentEntry 9 } + +optIfOTSnSinkCurrentLowerOutputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The lower limit threshold on output power. If + optIfOTSnSinkCurrentOutputPower drops to this value or below, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOTSnSinkCurrentEntry 10 } + +optIfOTSnSinkCurrentUpperOutputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper limit threshold on output power. If + optIfOTSnSinkCurrentOutputPower reaches or exceeds this value, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOTSnSinkCurrentEntry 11 } + +-- OTSn sink interval table +-- Contains data for previous 15-minute performance monitoring +-- intervals. + +optIfOTSnSinkIntervalTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOTSnSinkIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of historical OTSn sink performance monitoring + information." + ::= { optIfOTSn 3 } + +optIfOTSnSinkIntervalEntry OBJECT-TYPE + SYNTAX OptIfOTSnSinkIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OTSn sink performance + monitoring information of an interface during a particular + historical interval." + INDEX { ifIndex, optIfOTSnSinkIntervalNumber } + ::= { optIfOTSnSinkIntervalTable 1 } + +OptIfOTSnSinkIntervalEntry ::= + SEQUENCE { + optIfOTSnSinkIntervalNumber OptIfIntervalNumber, + optIfOTSnSinkIntervalSuspectedFlag TruthValue, + optIfOTSnSinkIntervalLastInputPower Integer32, + optIfOTSnSinkIntervalLowInputPower Integer32, + optIfOTSnSinkIntervalHighInputPower Integer32, + optIfOTSnSinkIntervalLastOutputPower Integer32, + optIfOTSnSinkIntervalLowOutputPower Integer32, + optIfOTSnSinkIntervalHighOutputPower Integer32 + + } + +optIfOTSnSinkIntervalNumber OBJECT-TYPE + SYNTAX OptIfIntervalNumber + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Uniquely identifies the interval." + ::= { optIfOTSnSinkIntervalEntry 1 } + +optIfOTSnSinkIntervalSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOTSnSinkIntervalEntry 2 } + +optIfOTSnSinkIntervalLastInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the input during the + interval." + ::= { optIfOTSnSinkIntervalEntry 3 } + +optIfOTSnSinkIntervalLowInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the input during the + interval." + ::= { optIfOTSnSinkIntervalEntry 4 } + + +optIfOTSnSinkIntervalHighInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the input during the + interval." + ::= { optIfOTSnSinkIntervalEntry 5 } + +optIfOTSnSinkIntervalLastOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the output during the + interval." + ::= { optIfOTSnSinkIntervalEntry 6 } + +optIfOTSnSinkIntervalLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + interval." + ::= { optIfOTSnSinkIntervalEntry 7 } + +optIfOTSnSinkIntervalHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + interval." + ::= { optIfOTSnSinkIntervalEntry 8 } + +-- OTSn sink current day table +-- Contains data for the current 24-hour performance +-- monitoring interval. + +optIfOTSnSinkCurDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOTSnSinkCurDayEntry + MAX-ACCESS not-accessible + STATUS current + + DESCRIPTION + "A table of OTSn sink performance monitoring information for + the current 24-hour interval." + ::= { optIfOTSn 4 } + +optIfOTSnSinkCurDayEntry OBJECT-TYPE + SYNTAX OptIfOTSnSinkCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OTSn sink performance + monitoring information of an interface for the current + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOTSnSinkCurDayTable 1 } + +OptIfOTSnSinkCurDayEntry ::= + SEQUENCE { + optIfOTSnSinkCurDaySuspectedFlag TruthValue, + optIfOTSnSinkCurDayLowInputPower Integer32, + optIfOTSnSinkCurDayHighInputPower Integer32, + optIfOTSnSinkCurDayLowOutputPower Integer32, + optIfOTSnSinkCurDayHighOutputPower Integer32 + } + +optIfOTSnSinkCurDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOTSnSinkCurDayEntry 1 } + +optIfOTSnSinkCurDayLowInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the input during the + current 24-hour interval." + ::= { optIfOTSnSinkCurDayEntry 2 } + +optIfOTSnSinkCurDayHighInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the input during the + current 24-hour interval." + ::= { optIfOTSnSinkCurDayEntry 3 } + +optIfOTSnSinkCurDayLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + current 24-hour interval." + ::= { optIfOTSnSinkCurDayEntry 4 } + +optIfOTSnSinkCurDayHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + current 24-hour interval." + ::= { optIfOTSnSinkCurDayEntry 5 } + +-- OTSn sink previous day table +-- Contains data for the previous 24-hour performance +-- monitoring interval. + +optIfOTSnSinkPrevDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOTSnSinkPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OTSn sink performance monitoring information for + the previous 24-hour interval." + ::= { optIfOTSn 5 } + +optIfOTSnSinkPrevDayEntry OBJECT-TYPE + SYNTAX OptIfOTSnSinkPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OTSn sink performance + monitoring information of an interface for the previous + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOTSnSinkPrevDayTable 1 } + + +OptIfOTSnSinkPrevDayEntry ::= + SEQUENCE { + optIfOTSnSinkPrevDaySuspectedFlag TruthValue, + optIfOTSnSinkPrevDayLastInputPower Integer32, + optIfOTSnSinkPrevDayLowInputPower Integer32, + optIfOTSnSinkPrevDayHighInputPower Integer32, + optIfOTSnSinkPrevDayLastOutputPower Integer32, + optIfOTSnSinkPrevDayLowOutputPower Integer32, + optIfOTSnSinkPrevDayHighOutputPower Integer32 + } + +optIfOTSnSinkPrevDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOTSnSinkPrevDayEntry 1 } + +optIfOTSnSinkPrevDayLastInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the input during the + previous 24-hour interval." + ::= { optIfOTSnSinkPrevDayEntry 2 } + +optIfOTSnSinkPrevDayLowInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the input during the + previous 24-hour interval." + ::= { optIfOTSnSinkPrevDayEntry 3 } + +optIfOTSnSinkPrevDayHighInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the input during the + previous 24-hour interval." + ::= { optIfOTSnSinkPrevDayEntry 4 } + + +optIfOTSnSinkPrevDayLastOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the output during the + previous 24-hour interval." + ::= { optIfOTSnSinkPrevDayEntry 5 } + +optIfOTSnSinkPrevDayLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + previous 24-hour interval." + ::= { optIfOTSnSinkPrevDayEntry 6 } + +optIfOTSnSinkPrevDayHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + previous 24-hour interval." + ::= { optIfOTSnSinkPrevDayEntry 7 } + +-- OTSn source current table +-- Contains data for the current 15-minute performance monitoring +-- interval. + +optIfOTSnSrcCurrentTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOTSnSrcCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OTSn source performance monitoring information for + the current 15-minute interval." + ::= { optIfOTSn 6 } + +optIfOTSnSrcCurrentEntry OBJECT-TYPE + SYNTAX OptIfOTSnSrcCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + + + "A conceptual row that contains OTSn source performance + monitoring information of an interface for the current + 15-minute interval." + INDEX { ifIndex } + ::= { optIfOTSnSrcCurrentTable 1 } + +OptIfOTSnSrcCurrentEntry ::= + SEQUENCE { + optIfOTSnSrcCurrentSuspectedFlag TruthValue, + optIfOTSnSrcCurrentOutputPower Integer32, + optIfOTSnSrcCurrentLowOutputPower Integer32, + optIfOTSnSrcCurrentHighOutputPower Integer32, + optIfOTSnSrcCurrentLowerOutputPowerThreshold Integer32, + optIfOTSnSrcCurrentUpperOutputPowerThreshold Integer32, + optIfOTSnSrcCurrentInputPower Integer32, + optIfOTSnSrcCurrentLowInputPower Integer32, + optIfOTSnSrcCurrentHighInputPower Integer32, + optIfOTSnSrcCurrentLowerInputPowerThreshold Integer32, + optIfOTSnSrcCurrentUpperInputPowerThreshold Integer32 + } + +optIfOTSnSrcCurrentSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOTSnSrcCurrentEntry 1 } + +optIfOTSnSrcCurrentOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The optical power monitored at the output." + ::= { optIfOTSnSrcCurrentEntry 2 } + +optIfOTSnSrcCurrentLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + + DESCRIPTION + "The lowest optical power monitored at the output during the + current 15-minute interval." + ::= { optIfOTSnSrcCurrentEntry 3 } + + +optIfOTSnSrcCurrentHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + current 15-minute interval." + ::= { optIfOTSnSrcCurrentEntry 4 } + +optIfOTSnSrcCurrentLowerOutputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The lower limit threshold on output power. If + optIfOTSnSrcCurrentOutputPower drops to this value or below, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOTSnSrcCurrentEntry 5 } + +optIfOTSnSrcCurrentUpperOutputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper limit threshold on output power. If + optIfOTSnSrcCurrentOutputPower reaches or exceeds this value, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOTSnSrcCurrentEntry 6 } + +optIfOTSnSrcCurrentInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The optical power monitored at the input." + ::= { optIfOTSnSrcCurrentEntry 7 } + +optIfOTSnSrcCurrentLowInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + + DESCRIPTION + + + "The lowest optical power monitored at the input during the + current 15-minute interval." + ::= { optIfOTSnSrcCurrentEntry 8 } + +optIfOTSnSrcCurrentHighInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the input during the + current 15-minute interval." + ::= { optIfOTSnSrcCurrentEntry 9 } + +optIfOTSnSrcCurrentLowerInputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The lower limit threshold on input power. If + optIfOTSnSrcCurrentInputPower drops to this value or below, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOTSnSrcCurrentEntry 10 } + +optIfOTSnSrcCurrentUpperInputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper limit threshold on input power. If + optIfOTSnSrcCurrentInputPower reaches or exceeds this value, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOTSnSrcCurrentEntry 11 } + +-- OTSn source interval table +-- Contains data for previous 15-minute performance monitoring +-- intervals. + +optIfOTSnSrcIntervalTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOTSnSrcIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of historical OTSn source performance monitoring + information." + ::= { optIfOTSn 7 } + + +optIfOTSnSrcIntervalEntry OBJECT-TYPE + SYNTAX OptIfOTSnSrcIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OTSn source performance + monitoring information of an interface during a particular + historical interval." + INDEX { ifIndex, optIfOTSnSrcIntervalNumber } + ::= { optIfOTSnSrcIntervalTable 1 } + +OptIfOTSnSrcIntervalEntry ::= + SEQUENCE { + optIfOTSnSrcIntervalNumber OptIfIntervalNumber, + optIfOTSnSrcIntervalSuspectedFlag TruthValue, + optIfOTSnSrcIntervalLastOutputPower Integer32, + optIfOTSnSrcIntervalLowOutputPower Integer32, + optIfOTSnSrcIntervalHighOutputPower Integer32, + optIfOTSnSrcIntervalLastInputPower Integer32, + optIfOTSnSrcIntervalLowInputPower Integer32, + optIfOTSnSrcIntervalHighInputPower Integer32 + } + +optIfOTSnSrcIntervalNumber OBJECT-TYPE + SYNTAX OptIfIntervalNumber + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Uniquely identifies the interval." + ::= { optIfOTSnSrcIntervalEntry 1 } + +optIfOTSnSrcIntervalSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOTSnSrcIntervalEntry 2 } + +optIfOTSnSrcIntervalLastOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the output during the + interval." + ::= { optIfOTSnSrcIntervalEntry 3 } + + +optIfOTSnSrcIntervalLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + interval." + ::= { optIfOTSnSrcIntervalEntry 4 } + +optIfOTSnSrcIntervalHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + interval." + ::= { optIfOTSnSrcIntervalEntry 5 } + +optIfOTSnSrcIntervalLastInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the input during the + interval." + ::= { optIfOTSnSrcIntervalEntry 6 } + +optIfOTSnSrcIntervalLowInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the input during the + interval." + ::= { optIfOTSnSrcIntervalEntry 7 } + +optIfOTSnSrcIntervalHighInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the input during the + interval." + + + ::= { optIfOTSnSrcIntervalEntry 8 } + + +-- OTSn source current day table +-- Contains data for the current 24-hour performance +-- monitoring interval. + +optIfOTSnSrcCurDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOTSnSrcCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OTSn source performance monitoring information for + the current 24-hour interval." + ::= { optIfOTSn 8 } + +optIfOTSnSrcCurDayEntry OBJECT-TYPE + SYNTAX OptIfOTSnSrcCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OTSn source performance + monitoring information of an interface for the current + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOTSnSrcCurDayTable 1 } + +OptIfOTSnSrcCurDayEntry ::= + SEQUENCE { + optIfOTSnSrcCurDaySuspectedFlag TruthValue, + optIfOTSnSrcCurDayLowOutputPower Integer32, + optIfOTSnSrcCurDayHighOutputPower Integer32, + optIfOTSnSrcCurDayLowInputPower Integer32, + optIfOTSnSrcCurDayHighInputPower Integer32 + } + +optIfOTSnSrcCurDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOTSnSrcCurDayEntry 1 } + +optIfOTSnSrcCurDayLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + current 24-hour interval." + ::= { optIfOTSnSrcCurDayEntry 2 } + +optIfOTSnSrcCurDayHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + current 24-hour interval." + ::= { optIfOTSnSrcCurDayEntry 3 } + +optIfOTSnSrcCurDayLowInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the input during the + current 24-hour interval." + ::= { optIfOTSnSrcCurDayEntry 4 } + +optIfOTSnSrcCurDayHighInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the input during the + current 24-hour interval." + ::= { optIfOTSnSrcCurDayEntry 5 } + +-- OTSn source previous day table +-- Contains data for the previous 24-hour performance +-- monitoring interval. + +optIfOTSnSrcPrevDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOTSnSrcPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OTSn source performance monitoring information for + the previous 24-hour interval." + ::= { optIfOTSn 9 } + + +optIfOTSnSrcPrevDayEntry OBJECT-TYPE + SYNTAX OptIfOTSnSrcPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OTSn source performance + monitoring information of an interface for the previous + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOTSnSrcPrevDayTable 1 } + +OptIfOTSnSrcPrevDayEntry ::= + SEQUENCE { + optIfOTSnSrcPrevDaySuspectedFlag TruthValue, + optIfOTSnSrcPrevDayLastOutputPower Integer32, + optIfOTSnSrcPrevDayLowOutputPower Integer32, + optIfOTSnSrcPrevDayHighOutputPower Integer32, + optIfOTSnSrcPrevDayLastInputPower Integer32, + optIfOTSnSrcPrevDayLowInputPower Integer32, + optIfOTSnSrcPrevDayHighInputPower Integer32 + } + +optIfOTSnSrcPrevDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOTSnSrcPrevDayEntry 1 } + +optIfOTSnSrcPrevDayLastOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the output during the + previous 24-hour interval." + ::= { optIfOTSnSrcPrevDayEntry 2 } + +optIfOTSnSrcPrevDayLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + previous 24-hour interval." + + + ::= { optIfOTSnSrcPrevDayEntry 3 } + +optIfOTSnSrcPrevDayHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + previous 24-hour interval." + ::= { optIfOTSnSrcPrevDayEntry 4 } + +optIfOTSnSrcPrevDayLastInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the input during the + previous 24-hour interval." + ::= { optIfOTSnSrcPrevDayEntry 5 } + +optIfOTSnSrcPrevDayLowInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the input during the + previous 24-hour interval." + ::= { optIfOTSnSrcPrevDayEntry 6 } + +optIfOTSnSrcPrevDayHighInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the input during the + previous 24-hour interval." + ::= { optIfOTSnSrcPrevDayEntry 7 } + + +-- the optIfOMSn group +-- This group handles the configuration and performance monitoring +-- information for OMS layers. + +-- OMSn config table + +optIfOMSnConfigTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOMSnConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OMSn configuration information." + ::= { optIfOMSn 1 } + +optIfOMSnConfigEntry OBJECT-TYPE + SYNTAX OptIfOMSnConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OMSn configuration + information of an interface." + INDEX { ifIndex } + ::= { optIfOMSnConfigTable 1 } + +OptIfOMSnConfigEntry ::= + SEQUENCE { + optIfOMSnDirectionality OptIfDirectionality, + optIfOMSnCurrentStatus BITS + } + +optIfOMSnDirectionality OBJECT-TYPE + SYNTAX OptIfDirectionality + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the directionality of the entity." + ::= { optIfOMSnConfigEntry 1 } + +optIfOMSnCurrentStatus OBJECT-TYPE + SYNTAX BITS { + ssfP(0), + ssfO(1), + ssf(2), + bdiP(3), + bdiO(4), + bdi(5), + losP(6) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the defect condition of the entity, if any. + This object is applicable only to full capability + systems whose interface type is IaDI and for which + + + optIfOMSnDirectionality has the value sink(1) or + bidirectional(3)." + ::= { optIfOMSnConfigEntry 2 } + +-- OMSn sink current table +-- Contains data for the current 15-minute performance monitoring +-- interval. + +optIfOMSnSinkCurrentTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOMSnSinkCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OMSn sink performance monitoring information for + the current 15-minute interval." + ::= { optIfOMSn 2 } + +optIfOMSnSinkCurrentEntry OBJECT-TYPE + SYNTAX OptIfOMSnSinkCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OMSn sink performance + monitoring information of an interface for the current + 15-minute interval." + INDEX { ifIndex } + ::= { optIfOMSnSinkCurrentTable 1 } + +OptIfOMSnSinkCurrentEntry ::= + SEQUENCE { + optIfOMSnSinkCurrentSuspectedFlag TruthValue, + optIfOMSnSinkCurrentAggregatedInputPower Integer32, + optIfOMSnSinkCurrentLowAggregatedInputPower Integer32, + optIfOMSnSinkCurrentHighAggregatedInputPower Integer32, + optIfOMSnSinkCurrentLowerInputPowerThreshold Integer32, + optIfOMSnSinkCurrentUpperInputPowerThreshold Integer32, + optIfOMSnSinkCurrentOutputPower Integer32, + optIfOMSnSinkCurrentLowOutputPower Integer32, + optIfOMSnSinkCurrentHighOutputPower Integer32, + optIfOMSnSinkCurrentLowerOutputPowerThreshold Integer32, + optIfOMSnSinkCurrentUpperOutputPowerThreshold Integer32 + } + +optIfOMSnSinkCurrentSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + + + "If true, the data in this entry may be unreliable." + ::= { optIfOMSnSinkCurrentEntry 1 } + +optIfOMSnSinkCurrentAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The aggregated optical power of all the DWDM input + channels." + ::= { optIfOMSnSinkCurrentEntry 2 } + +optIfOMSnSinkCurrentLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power of all the DWDM input + channels during the current 15-minute interval." + ::= { optIfOMSnSinkCurrentEntry 3 } + +optIfOMSnSinkCurrentHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power of all the DWDM input + channels during the current 15-minute interval." + ::= { optIfOMSnSinkCurrentEntry 4 } + +optIfOMSnSinkCurrentLowerInputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The lower limit threshold on aggregated input power. If + optIfOMSnSinkCurrentAggregatedInputPower drops to this value + or below, a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOMSnSinkCurrentEntry 5 } + +optIfOMSnSinkCurrentUpperInputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + + + STATUS current + DESCRIPTION + "The upper limit threshold on aggregated input power. If + optIfOMSnSinkCurrentAggregatedInputPower reaches or exceeds + this value, a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOMSnSinkCurrentEntry 6 } + +optIfOMSnSinkCurrentOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The optical power monitored at the output." + ::= { optIfOMSnSinkCurrentEntry 7 } + +optIfOMSnSinkCurrentLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output + during the current 15-minute interval." + ::= { optIfOMSnSinkCurrentEntry 8 } + +optIfOMSnSinkCurrentHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output + during the current 15-minute interval." + ::= { optIfOMSnSinkCurrentEntry 9 } + +optIfOMSnSinkCurrentLowerOutputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The lower limit threshold on output power. If + optIfOMSnSinkCurrentOutputPower drops to this value + or below, a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOMSnSinkCurrentEntry 10 } + +optIfOMSnSinkCurrentUpperOutputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper limit threshold on output power. If + optIfOMSnSinkCurrentOutputPower reaches or exceeds + this value, a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOMSnSinkCurrentEntry 11 } + +-- OMSn sink interval table +-- Contains data for previous 15-minute performance monitoring +-- intervals. + +optIfOMSnSinkIntervalTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOMSnSinkIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of historical OMSn sink performance monitoring + information." + ::= { optIfOMSn 3 } + +optIfOMSnSinkIntervalEntry OBJECT-TYPE + SYNTAX OptIfOMSnSinkIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OMSn sink performance + monitoring information of an interface during a particular + historical interval." + INDEX { ifIndex, optIfOMSnSinkIntervalNumber } + ::= { optIfOMSnSinkIntervalTable 1 } + +OptIfOMSnSinkIntervalEntry ::= + SEQUENCE { + optIfOMSnSinkIntervalNumber OptIfIntervalNumber, + optIfOMSnSinkIntervalSuspectedFlag TruthValue, + optIfOMSnSinkIntervalLastAggregatedInputPower Integer32, + optIfOMSnSinkIntervalLowAggregatedInputPower Integer32, + optIfOMSnSinkIntervalHighAggregatedInputPower Integer32, + optIfOMSnSinkIntervalLastOutputPower Integer32, + optIfOMSnSinkIntervalLowOutputPower Integer32, + optIfOMSnSinkIntervalHighOutputPower Integer32 + } + +optIfOMSnSinkIntervalNumber OBJECT-TYPE + SYNTAX OptIfIntervalNumber + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Uniquely identifies the interval." + ::= { optIfOMSnSinkIntervalEntry 1 } + +optIfOMSnSinkIntervalSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOMSnSinkIntervalEntry 2 } + +optIfOMSnSinkIntervalLastAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last aggregated optical power of all the DWDM input + channels during the interval." + ::= { optIfOMSnSinkIntervalEntry 3 } + +optIfOMSnSinkIntervalLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power of all the DWDM input + channels during the interval." + ::= { optIfOMSnSinkIntervalEntry 4 } + +optIfOMSnSinkIntervalHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power of all the DWDM input + channels during the interval." + ::= { optIfOMSnSinkIntervalEntry 5 } + +optIfOMSnSinkIntervalLastOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power at the output + during the interval." + ::= { optIfOMSnSinkIntervalEntry 6 } + +optIfOMSnSinkIntervalLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power at the output + during the interval." + ::= { optIfOMSnSinkIntervalEntry 7 } + +optIfOMSnSinkIntervalHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power at the output + during the interval." + ::= { optIfOMSnSinkIntervalEntry 8 } + +-- OMSn sink current day table +-- Contains data for the current 24-hour performance +-- monitoring interval. + +optIfOMSnSinkCurDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOMSnSinkCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OMSn sink performance monitoring information for + the current 24-hour interval." + ::= { optIfOMSn 4 } + +optIfOMSnSinkCurDayEntry OBJECT-TYPE + SYNTAX OptIfOMSnSinkCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OMSn sink performance + monitoring information of an interface for the current + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOMSnSinkCurDayTable 1 } + +OptIfOMSnSinkCurDayEntry ::= + SEQUENCE { + optIfOMSnSinkCurDaySuspectedFlag TruthValue, + optIfOMSnSinkCurDayLowAggregatedInputPower Integer32, + optIfOMSnSinkCurDayHighAggregatedInputPower Integer32, + optIfOMSnSinkCurDayLowOutputPower Integer32, + optIfOMSnSinkCurDayHighOutputPower Integer32 + } + +optIfOMSnSinkCurDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOMSnSinkCurDayEntry 1 } + +optIfOMSnSinkCurDayLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power of all the DWDM input + channels during the current 24-hour interval." + ::= { optIfOMSnSinkCurDayEntry 2 } + +optIfOMSnSinkCurDayHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power of all the DWDM input + channels during the current 24-hour interval." + ::= { optIfOMSnSinkCurDayEntry 3 } + +optIfOMSnSinkCurDayLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power at the output + during the current 24-hour interval." + ::= { optIfOMSnSinkCurDayEntry 4 } + +optIfOMSnSinkCurDayHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power at the output + during the current 24-hour interval." + ::= { optIfOMSnSinkCurDayEntry 5 } + +-- OMSn sink previous day table +-- Contains data for the previous 24-hour performance +-- monitoring interval. + +optIfOMSnSinkPrevDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOMSnSinkPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OMSn sink performance monitoring information for + the previous 24-hour interval." + ::= { optIfOMSn 5 } + +optIfOMSnSinkPrevDayEntry OBJECT-TYPE + SYNTAX OptIfOMSnSinkPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OMSn sink performance + monitoring information of an interface for the previous + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOMSnSinkPrevDayTable 1 } + +OptIfOMSnSinkPrevDayEntry ::= + SEQUENCE { + optIfOMSnSinkPrevDaySuspectedFlag TruthValue, + optIfOMSnSinkPrevDayLastAggregatedInputPower Integer32, + optIfOMSnSinkPrevDayLowAggregatedInputPower Integer32, + optIfOMSnSinkPrevDayHighAggregatedInputPower Integer32, + optIfOMSnSinkPrevDayLastOutputPower Integer32, + optIfOMSnSinkPrevDayLowOutputPower Integer32, + optIfOMSnSinkPrevDayHighOutputPower Integer32 + } + +optIfOMSnSinkPrevDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOMSnSinkPrevDayEntry 1 } + +optIfOMSnSinkPrevDayLastAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last aggregated optical power of all the DWDM input + channels during the previous 24-hour interval." + ::= { optIfOMSnSinkPrevDayEntry 2 } + +optIfOMSnSinkPrevDayLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power of all the DWDM input + channels during the previous 24-hour interval." + ::= { optIfOMSnSinkPrevDayEntry 3 } + +optIfOMSnSinkPrevDayHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power of all the DWDM input + channels during the previous 24-hour interval." + ::= { optIfOMSnSinkPrevDayEntry 4 } + +optIfOMSnSinkPrevDayLastOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power at the output + during the previous 24-hour interval." + ::= { optIfOMSnSinkPrevDayEntry 5 } + +optIfOMSnSinkPrevDayLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power at the output + during the previous 24-hour interval." + ::= { optIfOMSnSinkPrevDayEntry 6 } + +optIfOMSnSinkPrevDayHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power at the output + during the previous 24-hour interval." + ::= { optIfOMSnSinkPrevDayEntry 7 } + +-- OMSn source current table +-- Contains data for the current 15-minute performance monitoring +-- interval. + +optIfOMSnSrcCurrentTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOMSnSrcCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OMSn source performance monitoring information for + the current 15-minute interval." + ::= { optIfOMSn 6 } + +optIfOMSnSrcCurrentEntry OBJECT-TYPE + SYNTAX OptIfOMSnSrcCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OMSn source performance + monitoring information of an interface for the current + 15-minute interval." + INDEX { ifIndex } + ::= { optIfOMSnSrcCurrentTable 1 } + +OptIfOMSnSrcCurrentEntry ::= + SEQUENCE { + optIfOMSnSrcCurrentSuspectedFlag TruthValue, + optIfOMSnSrcCurrentOutputPower Integer32, + optIfOMSnSrcCurrentLowOutputPower Integer32, + optIfOMSnSrcCurrentHighOutputPower Integer32, + optIfOMSnSrcCurrentLowerOutputPowerThreshold Integer32, + optIfOMSnSrcCurrentUpperOutputPowerThreshold Integer32, + optIfOMSnSrcCurrentAggregatedInputPower Integer32, + optIfOMSnSrcCurrentLowAggregatedInputPower Integer32, + optIfOMSnSrcCurrentHighAggregatedInputPower Integer32, + optIfOMSnSrcCurrentLowerInputPowerThreshold Integer32, + optIfOMSnSrcCurrentUpperInputPowerThreshold Integer32 + } + +optIfOMSnSrcCurrentSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOMSnSrcCurrentEntry 1 } + +optIfOMSnSrcCurrentOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The optical power monitored at the output." + ::= { optIfOMSnSrcCurrentEntry 2 } + +optIfOMSnSrcCurrentLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + current 15-minute interval." + ::= { optIfOMSnSrcCurrentEntry 3 } + +optIfOMSnSrcCurrentHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + current 15-minute interval." + ::= { optIfOMSnSrcCurrentEntry 4 } + +optIfOMSnSrcCurrentLowerOutputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The lower limit threshold on output power. If + optIfOMSnSrcCurrentOutputPower drops to this value or below, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOMSnSrcCurrentEntry 5 } + +optIfOMSnSrcCurrentUpperOutputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper limit threshold on output power. If + optIfOMSnSrcCurrentOutputPower reaches or exceeds this value, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOMSnSrcCurrentEntry 6 } + +optIfOMSnSrcCurrentAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The aggregated optical power at the input." + ::= { optIfOMSnSrcCurrentEntry 7 } + +optIfOMSnSrcCurrentLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power at the input + during the current 15-minute interval." + ::= { optIfOMSnSrcCurrentEntry 8 } + +optIfOMSnSrcCurrentHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power at the input + during the current 15-minute interval." + ::= { optIfOMSnSrcCurrentEntry 9 } + + +optIfOMSnSrcCurrentLowerInputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The lower limit threshold on aggregated input power. If + optIfOMSnSrcCurrentAggregatedInputPower drops to this value + or below, a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOMSnSrcCurrentEntry 10 } + +optIfOMSnSrcCurrentUpperInputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper limit threshold on aggregated input power. If + optIfOMSnSrcCurrentAggregatedInputPower reaches or exceeds + this value, a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOMSnSrcCurrentEntry 11 } + + +-- OMSn source interval table +-- Contains data for previous 15-minute performance monitoring +-- intervals. + +optIfOMSnSrcIntervalTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOMSnSrcIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of historical OMSn source performance monitoring + information." + ::= { optIfOMSn 7 } + +optIfOMSnSrcIntervalEntry OBJECT-TYPE + SYNTAX OptIfOMSnSrcIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OMSn source performance + monitoring information of an interface during a particular + historical interval." + INDEX { ifIndex, optIfOMSnSrcIntervalNumber } + ::= { optIfOMSnSrcIntervalTable 1 } + +OptIfOMSnSrcIntervalEntry ::= + SEQUENCE { + optIfOMSnSrcIntervalNumber OptIfIntervalNumber, + optIfOMSnSrcIntervalSuspectedFlag TruthValue, + optIfOMSnSrcIntervalLastOutputPower Integer32, + optIfOMSnSrcIntervalLowOutputPower Integer32, + optIfOMSnSrcIntervalHighOutputPower Integer32, + optIfOMSnSrcIntervalLastAggregatedInputPower Integer32, + optIfOMSnSrcIntervalLowAggregatedInputPower Integer32, + optIfOMSnSrcIntervalHighAggregatedInputPower Integer32 + } + +optIfOMSnSrcIntervalNumber OBJECT-TYPE + SYNTAX OptIfIntervalNumber + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Uniquely identifies the interval." + ::= { optIfOMSnSrcIntervalEntry 1 } + +optIfOMSnSrcIntervalSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOMSnSrcIntervalEntry 2 } + +optIfOMSnSrcIntervalLastOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the output during the + interval." + ::= { optIfOMSnSrcIntervalEntry 3 } + +optIfOMSnSrcIntervalLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + interval." + ::= { optIfOMSnSrcIntervalEntry 4 } + +optIfOMSnSrcIntervalHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + interval." + ::= { optIfOMSnSrcIntervalEntry 5 } + +optIfOMSnSrcIntervalLastAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last aggregated optical power at the input + during the interval." + ::= { optIfOMSnSrcIntervalEntry 6 } + +optIfOMSnSrcIntervalLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power at the input + during the interval." + ::= { optIfOMSnSrcIntervalEntry 7 } + +optIfOMSnSrcIntervalHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power at the input + during the interval." + ::= { optIfOMSnSrcIntervalEntry 8 } + +-- OMSn source current day table +-- Contains data for the current 24-hour performance +-- monitoring interval. + +optIfOMSnSrcCurDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOMSnSrcCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OMSn source performance monitoring information for + the current 24-hour interval." + ::= { optIfOMSn 8 } + +optIfOMSnSrcCurDayEntry OBJECT-TYPE + SYNTAX OptIfOMSnSrcCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OMSn source performance + monitoring information of an interface for the current + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOMSnSrcCurDayTable 1 } + +OptIfOMSnSrcCurDayEntry ::= + SEQUENCE { + optIfOMSnSrcCurDaySuspectedFlag TruthValue, + optIfOMSnSrcCurDayLowOutputPower Integer32, + optIfOMSnSrcCurDayHighOutputPower Integer32, + optIfOMSnSrcCurDayLowAggregatedInputPower Integer32, + optIfOMSnSrcCurDayHighAggregatedInputPower Integer32 + } + +optIfOMSnSrcCurDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOMSnSrcCurDayEntry 1 } + +optIfOMSnSrcCurDayLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + current 24-hour interval." + ::= { optIfOMSnSrcCurDayEntry 2 } + +optIfOMSnSrcCurDayHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + current 24-hour interval." + ::= { optIfOMSnSrcCurDayEntry 3 } + +optIfOMSnSrcCurDayLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power at the input + during the current 24-hour interval." + ::= { optIfOMSnSrcCurDayEntry 4 } + +optIfOMSnSrcCurDayHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power at the input + during the current 24-hour interval." + ::= { optIfOMSnSrcCurDayEntry 5 } + +-- OMSn source previous day table +-- Contains data for the previous 24-hour performance +-- monitoring interval. + +optIfOMSnSrcPrevDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOMSnSrcPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OMSn source performance monitoring information for + the previous 24-hour interval." + ::= { optIfOMSn 9 } + +optIfOMSnSrcPrevDayEntry OBJECT-TYPE + SYNTAX OptIfOMSnSrcPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OMSn source performance + monitoring information of an interface for the previous + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOMSnSrcPrevDayTable 1 } + + +OptIfOMSnSrcPrevDayEntry ::= + SEQUENCE { + optIfOMSnSrcPrevDaySuspectedFlag TruthValue, + optIfOMSnSrcPrevDayLastOutputPower Integer32, + optIfOMSnSrcPrevDayLowOutputPower Integer32, + optIfOMSnSrcPrevDayHighOutputPower Integer32, + optIfOMSnSrcPrevDayLastAggregatedInputPower Integer32, + optIfOMSnSrcPrevDayLowAggregatedInputPower Integer32, + optIfOMSnSrcPrevDayHighAggregatedInputPower Integer32 + } + +optIfOMSnSrcPrevDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOMSnSrcPrevDayEntry 1 } + +optIfOMSnSrcPrevDayLastOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the output during the + previous 24-hour interval." + ::= { optIfOMSnSrcPrevDayEntry 2 } + +optIfOMSnSrcPrevDayLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + previous 24-hour interval." + ::= { optIfOMSnSrcPrevDayEntry 3 } + +optIfOMSnSrcPrevDayHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + previous 24-hour interval." + ::= { optIfOMSnSrcPrevDayEntry 4 } + +optIfOMSnSrcPrevDayLastAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last aggregated optical power at the input during the + previous 24-hour interval." + ::= { optIfOMSnSrcPrevDayEntry 5 } + +optIfOMSnSrcPrevDayLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power at the input during the + previous 24-hour interval." + ::= { optIfOMSnSrcPrevDayEntry 6 } + +optIfOMSnSrcPrevDayHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power at the input during the + previous 24-hour interval." + ::= { optIfOMSnSrcPrevDayEntry 7 } + +-- the optIfOChGroup group +-- This group handles the configuration and performance monitoring +-- information for OChGroup layers. + +-- OChGroup config table + +optIfOChGroupConfigTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChGroupConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OChGroup configuration information." + ::= { optIfOChGroup 1 } + +optIfOChGroupConfigEntry OBJECT-TYPE + SYNTAX OptIfOChGroupConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OChGroup configuration + information of an interface." + INDEX { ifIndex } + ::= { optIfOChGroupConfigTable 1 } + +OptIfOChGroupConfigEntry ::= + SEQUENCE { + optIfOChGroupDirectionality OptIfDirectionality + } + +optIfOChGroupDirectionality OBJECT-TYPE + SYNTAX OptIfDirectionality + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the directionality of the entity." + ::= { optIfOChGroupConfigEntry 1 } + +-- OChGroup sink current table +-- Contains data for the current 15-minute performance monitoring +-- interval. + +optIfOChGroupSinkCurrentTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChGroupSinkCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OChGroup sink performance monitoring information for + the current 15-minute interval." + ::= { optIfOChGroup 2 } + +optIfOChGroupSinkCurrentEntry OBJECT-TYPE + SYNTAX OptIfOChGroupSinkCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OChGroup sink performance + monitoring information of an interface for the current + 15-minute interval." + INDEX { ifIndex } + ::= { optIfOChGroupSinkCurrentTable 1 } + +OptIfOChGroupSinkCurrentEntry ::= + SEQUENCE { + optIfOChGroupSinkCurrentSuspectedFlag TruthValue, + optIfOChGroupSinkCurrentAggregatedInputPower Integer32, + optIfOChGroupSinkCurrentLowAggregatedInputPower Integer32, + optIfOChGroupSinkCurrentHighAggregatedInputPower Integer32, + optIfOChGroupSinkCurrentLowerInputPowerThreshold Integer32, + optIfOChGroupSinkCurrentUpperInputPowerThreshold Integer32, + optIfOChGroupSinkCurrentOutputPower Integer32, + optIfOChGroupSinkCurrentLowOutputPower Integer32, + optIfOChGroupSinkCurrentHighOutputPower Integer32, + optIfOChGroupSinkCurrentLowerOutputPowerThreshold Integer32, + optIfOChGroupSinkCurrentUpperOutputPowerThreshold Integer32 + } + +optIfOChGroupSinkCurrentSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChGroupSinkCurrentEntry 1 } + +optIfOChGroupSinkCurrentAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The aggregated optical power of all the DWDM input + channels in the OChGroup." + ::= { optIfOChGroupSinkCurrentEntry 2 } + +optIfOChGroupSinkCurrentLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power of all the DWDM input + channels in the OChGroup during the current 15-minute interval." + ::= { optIfOChGroupSinkCurrentEntry 3 } + +optIfOChGroupSinkCurrentHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power of all the DWDM input + channels in the OChGroup during the current 15-minute interval." + ::= { optIfOChGroupSinkCurrentEntry 4 } + + +optIfOChGroupSinkCurrentLowerInputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The lower limit threshold on aggregated input power. If + optIfOChGroupSinkCurrentAggregatedInputPower drops to this value + or below, a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOChGroupSinkCurrentEntry 5 } + +optIfOChGroupSinkCurrentUpperInputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper limit threshold on aggregated input power. If + optIfOChGroupSinkCurrentAggregatedInputPower reaches or exceeds + this value, a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOChGroupSinkCurrentEntry 6 } + +optIfOChGroupSinkCurrentOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The optical power monitored at the output + in the OChGroup." + ::= { optIfOChGroupSinkCurrentEntry 7 } + +optIfOChGroupSinkCurrentLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output + in the OChGroup during the current 15-minute interval." + ::= { optIfOChGroupSinkCurrentEntry 8 } + +optIfOChGroupSinkCurrentHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output + in the OChGroup during the current 15-minute interval." + ::= { optIfOChGroupSinkCurrentEntry 9 } + +optIfOChGroupSinkCurrentLowerOutputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The lower limit threshold on the output power. If + optIfOChGroupSinkCurrentOutputPower drops to this value + or below, a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOChGroupSinkCurrentEntry 10 } + +optIfOChGroupSinkCurrentUpperOutputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper limit threshold on the output power. If + optIfOChGroupSinkCurrentOutputPower reaches or exceeds + this value, a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOChGroupSinkCurrentEntry 11 } + +-- OChGroup sink interval table +-- Contains data for previous 15-minute performance monitoring +-- intervals. + +optIfOChGroupSinkIntervalTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChGroupSinkIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of historical OChGroup sink performance monitoring + information." + ::= { optIfOChGroup 3 } + +optIfOChGroupSinkIntervalEntry OBJECT-TYPE + SYNTAX OptIfOChGroupSinkIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OChGroup sink performance + monitoring information of an interface during a particular + historical interval." + INDEX { ifIndex, optIfOChGroupSinkIntervalNumber } + ::= { optIfOChGroupSinkIntervalTable 1 } + +OptIfOChGroupSinkIntervalEntry ::= + SEQUENCE { + optIfOChGroupSinkIntervalNumber OptIfIntervalNumber, + optIfOChGroupSinkIntervalSuspectedFlag TruthValue, + optIfOChGroupSinkIntervalLastAggregatedInputPower Integer32, + optIfOChGroupSinkIntervalLowAggregatedInputPower Integer32, + optIfOChGroupSinkIntervalHighAggregatedInputPower Integer32, + optIfOChGroupSinkIntervalLastOutputPower Integer32, + optIfOChGroupSinkIntervalLowOutputPower Integer32, + optIfOChGroupSinkIntervalHighOutputPower Integer32 + } + +optIfOChGroupSinkIntervalNumber OBJECT-TYPE + SYNTAX OptIfIntervalNumber + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Uniquely identifies the interval." + ::= { optIfOChGroupSinkIntervalEntry 1 } + +optIfOChGroupSinkIntervalSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChGroupSinkIntervalEntry 2 } + +optIfOChGroupSinkIntervalLastAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last aggregated optical power of all the DWDM input + channels in the OChGroup during the interval." + ::= { optIfOChGroupSinkIntervalEntry 3 } + +optIfOChGroupSinkIntervalLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power of all the DWDM input + channels in the OChGroup during the interval." + ::= { optIfOChGroupSinkIntervalEntry 4 } + +optIfOChGroupSinkIntervalHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power of all the DWDM input + channels in the OChGroup during the interval." + ::= { optIfOChGroupSinkIntervalEntry 5 } + +optIfOChGroupSinkIntervalLastOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the output + in the OChGroup during the interval." + ::= { optIfOChGroupSinkIntervalEntry 6 } + +optIfOChGroupSinkIntervalLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output + in the OChGroup during the interval." + ::= { optIfOChGroupSinkIntervalEntry 7 } + +optIfOChGroupSinkIntervalHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output + in the OChGroup during the interval." + ::= { optIfOChGroupSinkIntervalEntry 8 } + +-- OChGroup sink current day table +-- Contains data for the current 24-hour performance +-- monitoring interval. + +optIfOChGroupSinkCurDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChGroupSinkCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OChGroup sink performance monitoring information for + the current 24-hour interval." + ::= { optIfOChGroup 4 } + +optIfOChGroupSinkCurDayEntry OBJECT-TYPE + SYNTAX OptIfOChGroupSinkCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OChGroup sink performance + monitoring information of an interface for the current + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOChGroupSinkCurDayTable 1 } + +OptIfOChGroupSinkCurDayEntry ::= + SEQUENCE { + optIfOChGroupSinkCurDaySuspectedFlag TruthValue, + optIfOChGroupSinkCurDayLowAggregatedInputPower Integer32, + optIfOChGroupSinkCurDayHighAggregatedInputPower Integer32, + optIfOChGroupSinkCurDayLowOutputPower Integer32, + optIfOChGroupSinkCurDayHighOutputPower Integer32 + } + +optIfOChGroupSinkCurDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChGroupSinkCurDayEntry 1 } + +optIfOChGroupSinkCurDayLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power of all the DWDM input + channels in the OChGroup during the current 24-hour interval." + ::= { optIfOChGroupSinkCurDayEntry 2 } + +optIfOChGroupSinkCurDayHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power of all the DWDM input + channels in the OChGroup during the current 24-hour interval." + ::= { optIfOChGroupSinkCurDayEntry 3 } + +optIfOChGroupSinkCurDayLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output + in the OChGroup during the current 24-hour interval." + ::= { optIfOChGroupSinkCurDayEntry 4 } + +optIfOChGroupSinkCurDayHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output + in the OChGroup during the current 24-hour interval." + ::= { optIfOChGroupSinkCurDayEntry 5 } + +-- OChGroup sink previous day table +-- Contains data for the previous 24-hour performance +-- monitoring interval. + +optIfOChGroupSinkPrevDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChGroupSinkPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OChGroup sink performance monitoring information for + the previous 24-hour interval." + ::= { optIfOChGroup 5 } + +optIfOChGroupSinkPrevDayEntry OBJECT-TYPE + SYNTAX OptIfOChGroupSinkPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OChGroup sink performance + monitoring information of an interface for the previous + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOChGroupSinkPrevDayTable 1 } + +OptIfOChGroupSinkPrevDayEntry ::= + SEQUENCE { + optIfOChGroupSinkPrevDaySuspectedFlag TruthValue, + optIfOChGroupSinkPrevDayLastAggregatedInputPower Integer32, + optIfOChGroupSinkPrevDayLowAggregatedInputPower Integer32, + optIfOChGroupSinkPrevDayHighAggregatedInputPower Integer32, + optIfOChGroupSinkPrevDayLastOutputPower Integer32, + optIfOChGroupSinkPrevDayLowOutputPower Integer32, + optIfOChGroupSinkPrevDayHighOutputPower Integer32 + } + +optIfOChGroupSinkPrevDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChGroupSinkPrevDayEntry 1 } + +optIfOChGroupSinkPrevDayLastAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last aggregated optical power of all the DWDM input + channels in the OChGroup during the previous 24-hour interval." + ::= { optIfOChGroupSinkPrevDayEntry 2 } + +optIfOChGroupSinkPrevDayLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power of all the DWDM input + channels in the OChGroup during the previous 24-hour interval." + ::= { optIfOChGroupSinkPrevDayEntry 3 } + +optIfOChGroupSinkPrevDayHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power of all the DWDM input + channels in the OChGroup during the previous 24-hour interval." + ::= { optIfOChGroupSinkPrevDayEntry 4 } + +optIfOChGroupSinkPrevDayLastOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the output + in the OChGroup during the previous 24-hour interval." + ::= { optIfOChGroupSinkPrevDayEntry 5 } + +optIfOChGroupSinkPrevDayLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output + in the OChGroup during the previous 24-hour interval." + ::= { optIfOChGroupSinkPrevDayEntry 6 } + +optIfOChGroupSinkPrevDayHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output + in the OChGroup during the previous 24-hour interval." + ::= { optIfOChGroupSinkPrevDayEntry 7 } + +-- OChGroup source current table +-- Contains data for the current 15-minute performance monitoring +-- interval. + +optIfOChGroupSrcCurrentTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChGroupSrcCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OChGroup source performance monitoring information for + the current 15-minute interval." + ::= { optIfOChGroup 6 } + +optIfOChGroupSrcCurrentEntry OBJECT-TYPE + SYNTAX OptIfOChGroupSrcCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OChGroup source performance + monitoring information of an interface for the current + 15-minute interval." + INDEX { ifIndex } + ::= { optIfOChGroupSrcCurrentTable 1 } + +OptIfOChGroupSrcCurrentEntry ::= + SEQUENCE { + optIfOChGroupSrcCurrentSuspectedFlag TruthValue, + optIfOChGroupSrcCurrentOutputPower Integer32, + optIfOChGroupSrcCurrentLowOutputPower Integer32, + optIfOChGroupSrcCurrentHighOutputPower Integer32, + optIfOChGroupSrcCurrentLowerOutputPowerThreshold Integer32, + optIfOChGroupSrcCurrentUpperOutputPowerThreshold Integer32, + optIfOChGroupSrcCurrentAggregatedInputPower Integer32, + optIfOChGroupSrcCurrentLowAggregatedInputPower Integer32, + optIfOChGroupSrcCurrentHighAggregatedInputPower Integer32, + optIfOChGroupSrcCurrentLowerInputPowerThreshold Integer32, + optIfOChGroupSrcCurrentUpperInputPowerThreshold Integer32 + } + +optIfOChGroupSrcCurrentSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChGroupSrcCurrentEntry 1 } + +optIfOChGroupSrcCurrentOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The optical power monitored at the output." + ::= { optIfOChGroupSrcCurrentEntry 2 } + +optIfOChGroupSrcCurrentLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + current 15-minute interval." + ::= { optIfOChGroupSrcCurrentEntry 3 } + +optIfOChGroupSrcCurrentHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + current 15-minute interval." + ::= { optIfOChGroupSrcCurrentEntry 4 } + +optIfOChGroupSrcCurrentLowerOutputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The lower limit threshold on output power. If + optIfOChGroupSrcCurrentOutputPower drops to this value or below, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOChGroupSrcCurrentEntry 5 } + +optIfOChGroupSrcCurrentUpperOutputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper limit threshold on output power. If + optIfOChGroupSrcCurrentOutputPower reaches or exceeds this value, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOChGroupSrcCurrentEntry 6 } + +optIfOChGroupSrcCurrentAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The aggregated optical power monitored at the input." + ::= { optIfOChGroupSrcCurrentEntry 7 } + +optIfOChGroupSrcCurrentLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power monitored at the input + during the current 15-minute interval." + ::= { optIfOChGroupSrcCurrentEntry 8 } + +optIfOChGroupSrcCurrentHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power monitored at the input + during the current 15-minute interval." + ::= { optIfOChGroupSrcCurrentEntry 9 } + +optIfOChGroupSrcCurrentLowerInputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The lower limit threshold on input power. If + optIfOChGroupSrcCurrentAggregatedInputPower drops to this value + or below, a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOChGroupSrcCurrentEntry 10 } + +optIfOChGroupSrcCurrentUpperInputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper limit threshold on input power. If + optIfOChGroupSrcCurrentAggregatedInputPower reaches or exceeds + this value, a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOChGroupSrcCurrentEntry 11 } + +-- OChGroup source interval table +-- Contains data for previous 15-minute performance monitoring +-- intervals. + +optIfOChGroupSrcIntervalTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChGroupSrcIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of historical OChGroup source performance monitoring + information." + ::= { optIfOChGroup 7 } + +optIfOChGroupSrcIntervalEntry OBJECT-TYPE + SYNTAX OptIfOChGroupSrcIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OChGroup source performance + monitoring information of an interface during a particular + historical interval." + INDEX { ifIndex, optIfOChGroupSrcIntervalNumber } + ::= { optIfOChGroupSrcIntervalTable 1 } + +OptIfOChGroupSrcIntervalEntry ::= + SEQUENCE { + optIfOChGroupSrcIntervalNumber OptIfIntervalNumber, + optIfOChGroupSrcIntervalSuspectedFlag TruthValue, + optIfOChGroupSrcIntervalLastOutputPower Integer32, + optIfOChGroupSrcIntervalLowOutputPower Integer32, + optIfOChGroupSrcIntervalHighOutputPower Integer32, + optIfOChGroupSrcIntervalLastAggregatedInputPower Integer32, + optIfOChGroupSrcIntervalLowAggregatedInputPower Integer32, + optIfOChGroupSrcIntervalHighAggregatedInputPower Integer32 + } + +optIfOChGroupSrcIntervalNumber OBJECT-TYPE + SYNTAX OptIfIntervalNumber + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Uniquely identifies the interval." + ::= { optIfOChGroupSrcIntervalEntry 1 } + +optIfOChGroupSrcIntervalSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChGroupSrcIntervalEntry 2 } + +optIfOChGroupSrcIntervalLastOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the output during the + interval." + ::= { optIfOChGroupSrcIntervalEntry 3 } + +optIfOChGroupSrcIntervalLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + interval." + ::= { optIfOChGroupSrcIntervalEntry 4 } + +optIfOChGroupSrcIntervalHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + interval." + ::= { optIfOChGroupSrcIntervalEntry 5 } + +optIfOChGroupSrcIntervalLastAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last aggregated optical power monitored at the input + during the interval." + ::= { optIfOChGroupSrcIntervalEntry 6 } + +optIfOChGroupSrcIntervalLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power monitored at the input + during the interval." + ::= { optIfOChGroupSrcIntervalEntry 7 } + +optIfOChGroupSrcIntervalHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power monitored at the input + during the interval." + ::= { optIfOChGroupSrcIntervalEntry 8 } + +-- OChGroup source current day table +-- Contains data for the current 24-hour performance +-- monitoring interval. + +optIfOChGroupSrcCurDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChGroupSrcCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OChGroup source performance monitoring information for + the current 24-hour interval." + ::= { optIfOChGroup 8 } + +optIfOChGroupSrcCurDayEntry OBJECT-TYPE + SYNTAX OptIfOChGroupSrcCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OChGroup source performance + monitoring information of an interface for the current + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOChGroupSrcCurDayTable 1 } + +OptIfOChGroupSrcCurDayEntry ::= + SEQUENCE { + optIfOChGroupSrcCurDaySuspectedFlag TruthValue, + optIfOChGroupSrcCurDayLowOutputPower Integer32, + optIfOChGroupSrcCurDayHighOutputPower Integer32, + optIfOChGroupSrcCurDayLowAggregatedInputPower Integer32, + optIfOChGroupSrcCurDayHighAggregatedInputPower Integer32 + } + +optIfOChGroupSrcCurDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChGroupSrcCurDayEntry 1 } + +optIfOChGroupSrcCurDayLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + current 24-hour interval." + ::= { optIfOChGroupSrcCurDayEntry 2 } + +optIfOChGroupSrcCurDayHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + current 24-hour interval." + ::= { optIfOChGroupSrcCurDayEntry 3 } + +optIfOChGroupSrcCurDayLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power monitored at the input + during the current 24-hour interval." + ::= { optIfOChGroupSrcCurDayEntry 4 } + +optIfOChGroupSrcCurDayHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power monitored at the input + during the current 24-hour interval." + ::= { optIfOChGroupSrcCurDayEntry 5 } + +-- OChGroup source previous day table +-- Contains data for the previous 24-hour performance +-- monitoring interval. + +optIfOChGroupSrcPrevDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChGroupSrcPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OChGroup source performance monitoring information for + the previous 24-hour interval." + ::= { optIfOChGroup 9 } + +optIfOChGroupSrcPrevDayEntry OBJECT-TYPE + SYNTAX OptIfOChGroupSrcPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OChGroup source performance + monitoring information of an interface for the previous + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOChGroupSrcPrevDayTable 1 } + +OptIfOChGroupSrcPrevDayEntry ::= + SEQUENCE { + optIfOChGroupSrcPrevDaySuspectedFlag TruthValue, + optIfOChGroupSrcPrevDayLastOutputPower Integer32, + optIfOChGroupSrcPrevDayLowOutputPower Integer32, + optIfOChGroupSrcPrevDayHighOutputPower Integer32, + optIfOChGroupSrcPrevDayLastAggregatedInputPower Integer32, + optIfOChGroupSrcPrevDayLowAggregatedInputPower Integer32, + optIfOChGroupSrcPrevDayHighAggregatedInputPower Integer32 + } + +optIfOChGroupSrcPrevDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChGroupSrcPrevDayEntry 1 } + +optIfOChGroupSrcPrevDayLastOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the output during the + previous 24-hour interval." + ::= { optIfOChGroupSrcPrevDayEntry 2 } + +optIfOChGroupSrcPrevDayLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + previous 24-hour interval." + ::= { optIfOChGroupSrcPrevDayEntry 3 } + +optIfOChGroupSrcPrevDayHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + previous 24-hour interval." + ::= { optIfOChGroupSrcPrevDayEntry 4 } + +optIfOChGroupSrcPrevDayLastAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last aggregated optical power monitored at the input + during the previous 24-hour interval." + ::= { optIfOChGroupSrcPrevDayEntry 5 } + +optIfOChGroupSrcPrevDayLowAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest aggregated optical power monitored at the input + during the previous 24-hour interval." + ::= { optIfOChGroupSrcPrevDayEntry 6 } + +optIfOChGroupSrcPrevDayHighAggregatedInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest aggregated optical power monitored at the input + during the previous 24-hour interval." + ::= { optIfOChGroupSrcPrevDayEntry 7 } + +-- the optIfOCh group +-- This group handles the configuration and +-- performance monitoring information for OCh layers. + +-- OCh config table + +optIfOChConfigTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OCh configuration information." + ::= { optIfOCh 1 } + +optIfOChConfigEntry OBJECT-TYPE + SYNTAX OptIfOChConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OCh configuration + information of an interface." + INDEX { ifIndex } + ::= { optIfOChConfigTable 1 } + +OptIfOChConfigEntry ::= + SEQUENCE { + optIfOChDirectionality OptIfDirectionality, + optIfOChCurrentStatus BITS + } + +optIfOChDirectionality OBJECT-TYPE + SYNTAX OptIfDirectionality + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the directionality of the entity." + ::= { optIfOChConfigEntry 1 } + +optIfOChCurrentStatus OBJECT-TYPE + SYNTAX BITS { + losP(0), + los(1), + oci(2), + ssfP(3), + ssfO(4), + ssf(5) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the defect condition of the entity, if any. + This object is applicable when optIfOChDirectionality + has the value sink(1) or bidirectional(3). + In full-capability systems the bit position los(1) is not used. + In reduced-capability systems or at IrDI interfaces only + the bit positions los(1) and ssfP(3) are used." + ::= { optIfOChConfigEntry 2 } + +-- OCh sink current table +-- Contains data for the current 15-minute performance monitoring +-- interval. + +optIfOChSinkCurrentTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChSinkCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OCh sink performance monitoring information for + the current 15-minute interval." + ::= { optIfOCh 2 } + +optIfOChSinkCurrentEntry OBJECT-TYPE + SYNTAX OptIfOChSinkCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OCh sink performance + monitoring information for an interface for the current + 15-minute interval." + INDEX { ifIndex } + ::= { optIfOChSinkCurrentTable 1 } + +OptIfOChSinkCurrentEntry ::= + SEQUENCE { + optIfOChSinkCurrentSuspectedFlag TruthValue, + optIfOChSinkCurrentInputPower Integer32, + optIfOChSinkCurrentLowInputPower Integer32, + optIfOChSinkCurrentHighInputPower Integer32, + optIfOChSinkCurrentLowerInputPowerThreshold Integer32, + optIfOChSinkCurrentUpperInputPowerThreshold Integer32 + } + +optIfOChSinkCurrentSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChSinkCurrentEntry 1 } + +optIfOChSinkCurrentInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The optical power monitored at the input." + ::= { optIfOChSinkCurrentEntry 2 } + +optIfOChSinkCurrentLowInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the input during the + current 15-minute interval." + ::= { optIfOChSinkCurrentEntry 3 } + +optIfOChSinkCurrentHighInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the input during the + current 15-minute interval." + ::= { optIfOChSinkCurrentEntry 4 } + +optIfOChSinkCurrentLowerInputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The lower limit threshold on input power. If + optIfOChSinkCurrentInputPower drops to this value or below, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOChSinkCurrentEntry 5 } + +optIfOChSinkCurrentUpperInputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper limit threshold on input power. If + optIfOChSinkCurrentInputPower reaches or exceeds this value, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOChSinkCurrentEntry 6 } + +-- OCh sink interval table +-- Contains data for previous 15-minute performance monitoring +-- intervals. + +optIfOChSinkIntervalTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChSinkIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of historical OCh sink performance monitoring + information." + ::= { optIfOCh 3 } + +optIfOChSinkIntervalEntry OBJECT-TYPE + SYNTAX OptIfOChSinkIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OCh sink performance + monitoring information of an interface during a particular + historical interval." + INDEX { ifIndex, optIfOChSinkIntervalNumber } + ::= { optIfOChSinkIntervalTable 1 } + +OptIfOChSinkIntervalEntry ::= + SEQUENCE { + optIfOChSinkIntervalNumber OptIfIntervalNumber, + optIfOChSinkIntervalSuspectedFlag TruthValue, + optIfOChSinkIntervalLastInputPower Integer32, + optIfOChSinkIntervalLowInputPower Integer32, + optIfOChSinkIntervalHighInputPower Integer32 + } + +optIfOChSinkIntervalNumber OBJECT-TYPE + SYNTAX OptIfIntervalNumber + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Uniquely identifies the interval." + ::= { optIfOChSinkIntervalEntry 1 } + +optIfOChSinkIntervalSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChSinkIntervalEntry 2 } + +optIfOChSinkIntervalLastInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the input during the + interval." + ::= { optIfOChSinkIntervalEntry 3 } + +optIfOChSinkIntervalLowInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the input during the + interval." + ::= { optIfOChSinkIntervalEntry 4 } + +optIfOChSinkIntervalHighInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the input during the + interval." + ::= { optIfOChSinkIntervalEntry 5 } + +-- OCh sink current day table +-- Contains data for the current 24-hour performance +-- monitoring interval. + +optIfOChSinkCurDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChSinkCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OCh sink performance monitoring information for + the current 24-hour interval." + ::= { optIfOCh 4 } + +optIfOChSinkCurDayEntry OBJECT-TYPE + SYNTAX OptIfOChSinkCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OCh sink performance + monitoring information of an interface for the current + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOChSinkCurDayTable 1 } + +OptIfOChSinkCurDayEntry ::= + SEQUENCE { + optIfOChSinkCurDaySuspectedFlag TruthValue, + optIfOChSinkCurDayLowInputPower Integer32, + optIfOChSinkCurDayHighInputPower Integer32 + } + +optIfOChSinkCurDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChSinkCurDayEntry 1 } + +optIfOChSinkCurDayLowInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the input during the + current 24-hour interval." + ::= { optIfOChSinkCurDayEntry 2 } + +optIfOChSinkCurDayHighInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the input during the + current 24-hour interval." + ::= { optIfOChSinkCurDayEntry 3 } + +-- OCh sink previous day table +-- Contains data for the previous 24-hour performance +-- monitoring interval. + +optIfOChSinkPrevDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChSinkPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OCh sink performance monitoring information for + the previous 24-hour interval." + ::= { optIfOCh 5 } + +optIfOChSinkPrevDayEntry OBJECT-TYPE + SYNTAX OptIfOChSinkPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OCh sink performance + monitoring information of an interface for the previous + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOChSinkPrevDayTable 1 } + +OptIfOChSinkPrevDayEntry ::= + SEQUENCE { + optIfOChSinkPrevDaySuspectedFlag TruthValue, + optIfOChSinkPrevDayLastInputPower Integer32, + optIfOChSinkPrevDayLowInputPower Integer32, + optIfOChSinkPrevDayHighInputPower Integer32 + } + +optIfOChSinkPrevDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChSinkPrevDayEntry 1 } + +optIfOChSinkPrevDayLastInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the input during the + previous 24-hour interval." + ::= { optIfOChSinkPrevDayEntry 2 } + +optIfOChSinkPrevDayLowInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the input during the + previous 24-hour interval." + ::= { optIfOChSinkPrevDayEntry 3 } + +optIfOChSinkPrevDayHighInputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the input during the + previous 24-hour interval." + ::= { optIfOChSinkPrevDayEntry 4 } + +-- OCh source current table +-- Contains data for the current 15-minute performance monitoring +-- interval. + +optIfOChSrcCurrentTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChSrcCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OCh source performance monitoring information for + the current 15-minute interval." + ::= { optIfOCh 6 } + +optIfOChSrcCurrentEntry OBJECT-TYPE + SYNTAX OptIfOChSrcCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OCh source performance + monitoring information of an interface for the current + 15-minute interval." + INDEX { ifIndex } + ::= { optIfOChSrcCurrentTable 1 } + +OptIfOChSrcCurrentEntry ::= + SEQUENCE { + optIfOChSrcCurrentSuspectedFlag TruthValue, + optIfOChSrcCurrentOutputPower Integer32, + optIfOChSrcCurrentLowOutputPower Integer32, + optIfOChSrcCurrentHighOutputPower Integer32, + optIfOChSrcCurrentLowerOutputPowerThreshold Integer32, + optIfOChSrcCurrentUpperOutputPowerThreshold Integer32 + } + +optIfOChSrcCurrentSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChSrcCurrentEntry 1 } + +optIfOChSrcCurrentOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The optical power monitored at the output." + ::= { optIfOChSrcCurrentEntry 2 } + +optIfOChSrcCurrentLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + current 15-minute interval." + ::= { optIfOChSrcCurrentEntry 3 } + +optIfOChSrcCurrentHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + current 15-minute interval." + ::= { optIfOChSrcCurrentEntry 4 } + +optIfOChSrcCurrentLowerOutputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The lower limit threshold on output power. If + optIfOChSrcCurrentOutputPower drops to this value or below, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOChSrcCurrentEntry 5 } + +optIfOChSrcCurrentUpperOutputPowerThreshold OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper limit threshold on output power. If + optIfOChSrcCurrentOutputPower reaches or exceeds this value, + a Threshold Crossing Alert (TCA) should be sent." + ::= { optIfOChSrcCurrentEntry 6 } + +-- OCh source interval table +-- Contains data for previous 15-minute performance monitoring +-- intervals. + +optIfOChSrcIntervalTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChSrcIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of historical OCh source performance monitoring + information." + ::= { optIfOCh 7 } + +optIfOChSrcIntervalEntry OBJECT-TYPE + SYNTAX OptIfOChSrcIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OCh source performance + monitoring information of an interface during a particular + historical interval." + INDEX { ifIndex, optIfOChSrcIntervalNumber } + ::= { optIfOChSrcIntervalTable 1 } + +OptIfOChSrcIntervalEntry ::= + SEQUENCE { + optIfOChSrcIntervalNumber OptIfIntervalNumber, + optIfOChSrcIntervalSuspectedFlag TruthValue, + optIfOChSrcIntervalLastOutputPower Integer32, + optIfOChSrcIntervalLowOutputPower Integer32, + optIfOChSrcIntervalHighOutputPower Integer32 + } + +optIfOChSrcIntervalNumber OBJECT-TYPE + SYNTAX OptIfIntervalNumber + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Uniquely identifies the interval." + ::= { optIfOChSrcIntervalEntry 1 } + +optIfOChSrcIntervalSuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChSrcIntervalEntry 2 } + +optIfOChSrcIntervalLastOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the output during the + interval." + ::= { optIfOChSrcIntervalEntry 3 } + +optIfOChSrcIntervalLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + interval." + ::= { optIfOChSrcIntervalEntry 4 } + +optIfOChSrcIntervalHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + interval." + ::= { optIfOChSrcIntervalEntry 5 } + +-- OCh source current day table +-- Contains data for the current 24-hour performance +-- monitoring interval. + +optIfOChSrcCurDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChSrcCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OCh source performance monitoring information for + the current 24-hour interval." + ::= { optIfOCh 8 } + +optIfOChSrcCurDayEntry OBJECT-TYPE + SYNTAX OptIfOChSrcCurDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OCh source performance + monitoring information of an interface for the current + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOChSrcCurDayTable 1 } + +OptIfOChSrcCurDayEntry ::= + SEQUENCE { + optIfOChSrcCurDaySuspectedFlag TruthValue, + optIfOChSrcCurDayLowOutputPower Integer32, + optIfOChSrcCurDayHighOutputPower Integer32 + } + +optIfOChSrcCurDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChSrcCurDayEntry 1 } + +optIfOChSrcCurDayLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + current 24-hour interval." + ::= { optIfOChSrcCurDayEntry 2 } + +optIfOChSrcCurDayHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + current 24-hour interval." + ::= { optIfOChSrcCurDayEntry 3 } + +-- OCh source previous day table +-- Contains data for the previous 24-hour performance +-- monitoring interval. + +optIfOChSrcPrevDayTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOChSrcPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OCh source performance monitoring information for + the previous 24-hour interval." + ::= { optIfOCh 9 } + +optIfOChSrcPrevDayEntry OBJECT-TYPE + SYNTAX OptIfOChSrcPrevDayEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OCh source performance + monitoring information of an interface for the previous + 24-hour interval." + INDEX { ifIndex } + ::= { optIfOChSrcPrevDayTable 1 } + +OptIfOChSrcPrevDayEntry ::= + SEQUENCE { + optIfOChSrcPrevDaySuspectedFlag TruthValue, + optIfOChSrcPrevDayLastOutputPower Integer32, + optIfOChSrcPrevDayLowOutputPower Integer32, + optIfOChSrcPrevDayHighOutputPower Integer32 + } + +optIfOChSrcPrevDaySuspectedFlag OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, the data in this entry may be unreliable." + ::= { optIfOChSrcPrevDayEntry 1 } + +optIfOChSrcPrevDayLastOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The last optical power monitored at the output during the + previous 24-hour interval." + ::= { optIfOChSrcPrevDayEntry 2 } + +optIfOChSrcPrevDayLowOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The lowest optical power monitored at the output during the + previous 24-hour interval." + ::= { optIfOChSrcPrevDayEntry 3 } + +optIfOChSrcPrevDayHighOutputPower OBJECT-TYPE + SYNTAX Integer32 + UNITS "0.1 dbm" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The highest optical power monitored at the output during the + previous 24-hour interval." + ::= { optIfOChSrcPrevDayEntry 4 } + +-- the optIfOTUk group +-- This group handles the configuration +-- information for OTUk layers. + +-- OTUk config table + +optIfOTUkConfigTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfOTUkConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of OTUk configuration information." + ::= { optIfOTUk 1 } + +optIfOTUkConfigEntry OBJECT-TYPE + SYNTAX OptIfOTUkConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains OTUk configuration + information of an interface." + INDEX { ifIndex } + ::= { optIfOTUkConfigTable 1 } + +OptIfOTUkConfigEntry ::= + SEQUENCE { + optIfOTUkDirectionality OptIfDirectionality, + optIfOTUkBitRateK OptIfBitRateK, + optIfOTUkTraceIdentifierTransmitted OptIfTxTI, + optIfOTUkDAPIExpected OptIfExDAPI, + optIfOTUkSAPIExpected OptIfExSAPI, + optIfOTUkTraceIdentifierAccepted OptIfAcTI, + optIfOTUkTIMDetMode OptIfTIMDetMode, + optIfOTUkTIMActEnabled TruthValue, + optIfOTUkDEGThr OptIfDEGThr, + optIfOTUkDEGM OptIfDEGM, + optIfOTUkSinkAdaptActive TruthValue, + optIfOTUkSourceAdaptActive TruthValue, + optIfOTUkSinkFECEnabled TruthValue, + optIfOTUkCurrentStatus BITS + } + +optIfOTUkDirectionality OBJECT-TYPE + SYNTAX OptIfDirectionality + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the directionality of the entity." + ::= { optIfOTUkConfigEntry 1 } + +optIfOTUkBitRateK OBJECT-TYPE + SYNTAX OptIfBitRateK + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the bit rate of the entity." + ::= { optIfOTUkConfigEntry 2 } + +optIfOTUkTraceIdentifierTransmitted OBJECT-TYPE + SYNTAX OptIfTxTI + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The trace identifier transmitted. + This object is applicable when optIfOTUkDirectionality + has the value source(2) or bidirectional(3). It must not + be instantiated in rows where optIfOTUkDirectionality + has the value sink(1). + If no value is ever set by a management entity for this + object, system-specific default value will be used. + Any implementation that instantiates this object must + document the system-specific default value or how it + is derived." + ::= { optIfOTUkConfigEntry 3 } + +optIfOTUkDAPIExpected OBJECT-TYPE + SYNTAX OptIfExDAPI + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The DAPI expected by the receiver. + This object is only applicable to the sink function, i.e., + only when optIfOTUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfOTUkDirectionality has the value source(2). + This object has no effect when optIfOTUkTIMDetMode has + the value off(1)." + ::= { optIfOTUkConfigEntry 4 } + +optIfOTUkSAPIExpected OBJECT-TYPE + SYNTAX OptIfExSAPI + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The SAPI expected by the receiver. + This object is only applicable to the sink function, i.e., + only when optIfOTUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfOTUkDirectionality has the value source(2). + This object has no effect when optIfOTUkTIMDetMode has + the value off(1)." + ::= { optIfOTUkConfigEntry 5 } + +optIfOTUkTraceIdentifierAccepted OBJECT-TYPE + SYNTAX OptIfAcTI + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The actual trace identifier accepted. + This object is only applicable to the sink function, i.e., + only when optIfOTUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfOTUkDirectionality has the value source(2). + The value of this object is unspecified when + optIfOTUkCurrentStatus indicates a near-end defect + (i.e., ssf(3), lof(4), ais(5), lom(6)) that prevents + extraction of the trace message." + ::= { optIfOTUkConfigEntry 6 } + +optIfOTUkTIMDetMode OBJECT-TYPE + SYNTAX OptIfTIMDetMode + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Indicates the mode of the Trace Identifier Mismatch (TIM) + Detection function. + This object is only applicable to the sink function, i.e., + only when optIfOTUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfOTUkDirectionality has the value source(2). + The default value of this object is off(1)." + ::= { optIfOTUkConfigEntry 7 } + +optIfOTUkTIMActEnabled OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Indicates whether the Trace Identifier Mismatch (TIM) + Consequent Action function is enabled. + This object is only applicable to the sink function, i.e., + only when optIfOTUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfOTUkDirectionality has the value source(2). + This object has no effect when optIfOTUkTIMDetMode has + the value off(1). + The default value of this object is false(2)." + ::= { optIfOTUkConfigEntry 8 } + +optIfOTUkDEGThr OBJECT-TYPE + SYNTAX OptIfDEGThr + UNITS "percentage" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Indicates the threshold level for declaring a performance + monitoring (PM) Second to be bad. A PM Second is declared bad if + the percentage of detected errored blocks in that second is + greater than or equal to optIfOTUkDEGThr. + This object is only applicable to the sink function, i.e., + only when optIfOTUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfOTUkDirectionality has the value source(2). + The default value of this object is Severely Errored Second + (SES) Estimator (See ITU-T G.7710)." + ::= { optIfOTUkConfigEntry 9 } + +optIfOTUkDEGM OBJECT-TYPE + SYNTAX OptIfDEGM + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Indicates the threshold level for declaring a Degraded Signal + defect (dDEG). A dDEG shall be declared if optIfOTUkDEGM + consecutive bad PM Seconds are detected. + This object is only applicable to the sink function, i.e., + only when optIfOTUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfOTUkDirectionality has the value source(2). + The default value of this object is 7 (See ITU-T G.7710)." + ::= { optIfOTUkConfigEntry 10 } + +optIfOTUkSinkAdaptActive OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Indicates whether the sink adaptation function is activated or + not. + This object is only applicable to the sink function, i.e., + only when optIfOTUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfOTUkDirectionality has the value source(2). + The default value of this object is false(2)." + ::= { optIfOTUkConfigEntry 11 } + +optIfOTUkSourceAdaptActive OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Indicates whether the source adaptation function is activated or + not. + This object is only applicable to the source function, i.e., + only when optIfOTUkDirectionality has the value source(2) + or bidirectional(3). It must not be instantiated in rows + where optIfOTUkDirectionality has the value sink(1). + The default value of this object is false(2)." + ::= { optIfOTUkConfigEntry 12 } + +optIfOTUkSinkFECEnabled OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "If Forward Error Correction (FEC) is supported, this object + indicates whether FEC at the OTUk sink adaptation function is + enabled or not. + This object is only applicable to the sink function, i.e., + only when optIfOTUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfOTUkDirectionality has the value source(2). + The default value of this object is true(1)." + ::= { optIfOTUkConfigEntry 13 } + +optIfOTUkCurrentStatus OBJECT-TYPE + SYNTAX BITS { + tim(0), + deg(1), + bdi(2), + ssf(3), + lof(4), + ais(5), + lom(6) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the defect condition of the entity, if any. + This object is only applicable to the sink function, i.e., + only when optIfOTUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfOTUkDirectionality has the value source(2)." + ::= { optIfOTUkConfigEntry 14 } + +-- GCC0 config table + +optIfGCC0ConfigTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfGCC0ConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of GCC0 configuration information." + ::= { optIfOTUk 2 } + + +optIfGCC0ConfigEntry OBJECT-TYPE + SYNTAX OptIfGCC0ConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains GCC0 configuration + information of an interface. Each instance must + correspond to an instance of optIfOTUkConfigEntry. + Separate source and/or sink instances may exist + for a given ifIndex value, or a single bidirectional + instance may exist, but a bidirectional instance may + not coexist with a source or sink instance. + Instances of this conceptual row persist across + agent restarts." + INDEX { ifIndex, optIfGCC0Directionality } + ::= { optIfGCC0ConfigTable 1 } + +OptIfGCC0ConfigEntry ::= + SEQUENCE { + optIfGCC0Directionality OptIfDirectionality, + optIfGCC0Application SnmpAdminString, + optIfGCC0RowStatus RowStatus + } + +optIfGCC0Directionality OBJECT-TYPE + SYNTAX OptIfDirectionality + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Indicates the directionality of the entity. + The values source(2) and bidirectional(3) are + not allowed if the corresponding instance of + optIfOTUkDirectionality has the value sink(1). + The values sink(1) and bidirectional(3) are + not allowed if the corresponding instance of + optIfOTUkDirectionality has the value source(2)." + ::= { optIfGCC0ConfigEntry 1 } + +optIfGCC0Application OBJECT-TYPE + SYNTAX SnmpAdminString + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates the application transported by the GCC0 entity. + Example applications are ECC, User data channel. + + The value of this object may not be changed when + optIfGCC0RowStatus has the value active(1)." + ::= { optIfGCC0ConfigEntry 2 } + +optIfGCC0RowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This columnar object is used for creating and deleting a + conceptual row of the optIfGCC0 config table. + It is used to model the addGCC0Access and removeGCC0Access + operations of an OTUk_TTP for GCC0 access control as defined + in G.874.1. Setting RowStatus to createAndGo or createAndWait + implies addGCC0Access. Setting RowStatus to destroy implies + removeGCC0Access." + ::= { optIfGCC0ConfigEntry 3 } + +-- the optIfODUk group +-- This group handles the configuration information +-- for the ODUk layers. + +-- ODUk config table + +optIfODUkConfigTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfODUkConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of ODUk configuration information." + ::= { optIfODUk 1 } + +optIfODUkConfigEntry OBJECT-TYPE + SYNTAX OptIfODUkConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains ODUk configuration + information of an interface." + INDEX { ifIndex } + ::= { optIfODUkConfigTable 1 } + +OptIfODUkConfigEntry ::= + SEQUENCE { + optIfODUkDirectionality OptIfDirectionality, + optIfODUkBitRateK OptIfBitRateK, + optIfODUkTcmFieldsInUse BITS, + optIfODUkPositionSeqCurrentSize Unsigned32, + optIfODUkTtpPresent TruthValue + } + +optIfODUkDirectionality OBJECT-TYPE + SYNTAX OptIfDirectionality + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the directionality of the entity." + ::= { optIfODUkConfigEntry 1 } + +optIfODUkBitRateK OBJECT-TYPE + SYNTAX OptIfBitRateK + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the bit rate of the entity." + ::= { optIfODUkConfigEntry 2 } + +optIfODUkTcmFieldsInUse OBJECT-TYPE + SYNTAX BITS { + tcmField1(0), + tcmField2(1), + tcmField3(2), + tcmField4(3), + tcmField5(4), + tcmField6(5) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the TCM field(s) that are currently in use. + The positions of the bits correspond to the TCM fields. + A bit that is set to 1 means that the corresponding TCM + field is used. This object will be updated when rows are + created in or deleted from the optIfODUkTConfigTable, or + the optIfODUkTNimConfigTable." + ::= { optIfODUkConfigEntry 3 } + +optIfODUkPositionSeqCurrentSize OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This variable indicates the current size of the position + sequence (i.e., number of TCM function and/or GCC12 + access that have been created in the ODUk interface). + When the value of this variable is greater than zero, + it means that one or more TCM function and/or GCC12 + access have been created in the ODUk interface. In this + case, there will be as many rows in the + optIfODUkPositionSeqTable as the value of + optIfODUkPositionSeqCurrentSize corresponding to this + ODUk interface, one row for each TCM function or GCC12 + access. The position of the TCM function and/or + GCC12 access within the sequence is indicated by the + optIfODUkPositionSeqPosition variable in + optIfODUkPositionSeqTable. + The optIfODUkPositionSeqTable also provides pointers + to the corresponding TCM function (optIfODUkT) and + GCC12 access (optIfGCC12) entities." + ::= { optIfODUkConfigEntry 4 } + +optIfODUkTtpPresent OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object has the value true(1) if the ifEntry under which + it is instantiated contains an ODUk Trail Termination Point, + i.e., is the endpoint of an ODUk path. In that case there + will be a corresponding row in the ODUk TTP config table and + it will not be possible to create corresponding rows in the + ODUk NIM config table. This object has the value false(2) + if the ifEntry under which it is instantiated contains an + intermediate ODUk Connection Termination Point. In that case + there is no corresponding row in the ODUk TTP config table, + but it will be possible to create corresponding rows in the + ODUk NIM config table. This object also affects the allowable + options in rows created in the GCC12 config table and in the + ODUkT config table, as specified in the DESCRIPTION clauses + of the columns in those tables." + ::= { optIfODUkConfigEntry 5 } + +-- ODUk Trail Termination Point (TTP) config table + +optIfODUkTtpConfigTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfODUkTtpConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of ODUk TTP configuration information." + ::= { optIfODUk 2 } + +optIfODUkTtpConfigEntry OBJECT-TYPE + SYNTAX OptIfODUkTtpConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains ODUk TTP configuration + information of an interface." + INDEX { ifIndex } + ::= { optIfODUkTtpConfigTable 1 } + +OptIfODUkTtpConfigEntry ::= + SEQUENCE { + optIfODUkTtpTraceIdentifierTransmitted OptIfTxTI, + optIfODUkTtpDAPIExpected OptIfExDAPI, + optIfODUkTtpSAPIExpected OptIfExSAPI, + optIfODUkTtpTraceIdentifierAccepted OptIfAcTI, + optIfODUkTtpTIMDetMode OptIfTIMDetMode, + optIfODUkTtpTIMActEnabled TruthValue, + optIfODUkTtpDEGThr OptIfDEGThr, + optIfODUkTtpDEGM OptIfDEGM, + optIfODUkTtpCurrentStatus BITS + } + +optIfODUkTtpTraceIdentifierTransmitted OBJECT-TYPE + SYNTAX OptIfTxTI + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The trace identifier transmitted. + This object is applicable when optIfODUkDirectionality + has the value source(2) or bidirectional(3). It must not + be instantiated in rows where optIfODUkDirectionality + has the value sink(1). + If no value is ever set by a management entity for this + object, system-specific default value will be used. + Any implementation that instantiates this object must + document the system-specific default value or how it + is derived." + ::= { optIfODUkTtpConfigEntry 1 } + +optIfODUkTtpDAPIExpected OBJECT-TYPE + SYNTAX OptIfExDAPI + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The DAPI expected by the receiver. + This object is only applicable to the sink function, i.e., + only when optIfODUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfODUkDirectionality has the value source(2). + This object has no effect when optIfODUkTtpTIMDetMode has + the value off(1)." + ::= { optIfODUkTtpConfigEntry 2 } + +optIfODUkTtpSAPIExpected OBJECT-TYPE + SYNTAX OptIfExSAPI + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The SAPI expected by the receiver. + This object is only applicable to the sink function, i.e., + only when optIfODUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfODUkDirectionality has the value source(2). + This object has no effect when optIfODUkTtpTIMDetMode has + the value off(1)." + ::= { optIfODUkTtpConfigEntry 3 } + +optIfODUkTtpTraceIdentifierAccepted OBJECT-TYPE + SYNTAX OptIfAcTI + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The actual trace identifier accepted. + This object is only applicable to the sink function, i.e., + only when optIfODUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfODUkDirectionality has the value source(2). + The value of this object is unspecified when + optIfODUkTtpCurrentStatus indicates a near-end defect + (i.e., oci(0), lck(1), ssf(5)) that prevents extraction + of the trace message." + ::= { optIfODUkTtpConfigEntry 4 } + +optIfODUkTtpTIMDetMode OBJECT-TYPE + SYNTAX OptIfTIMDetMode + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Indicates the mode of the Trace Identifier Mismatch (TIM) + Detection function. + This object is only applicable to the sink function, i.e., + only when optIfODUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfODUkDirectionality has the value source(2). + The default value of this object is off(1)." + ::= { optIfODUkTtpConfigEntry 5 } + +optIfODUkTtpTIMActEnabled OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Indicates whether the Trace Identifier Mismatch (TIM) + Consequent Action function is enabled. + This object is only applicable to the sink function, i.e., + only when optIfODUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfODUkDirectionality has the value source(2). + This object has no effect when optIfODUkTtpTIMDetMode has + the value off(1). + The default value of this object is false(2)." + ::= { optIfODUkTtpConfigEntry 6 } + +optIfODUkTtpDEGThr OBJECT-TYPE + SYNTAX OptIfDEGThr + UNITS "percentage" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Indicates the threshold level for declaring a performance + monitoring (PM) Second to be bad. A PM Second is declared bad if + the percentage of detected errored blocks in that second is + greater than or equal to optIfODUkDEGThr. + This object is only applicable to the sink function, i.e., + only when optIfODUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfODUkDirectionality has the value source(2). + The default value of this object is Severely Errored Second + (SES) Estimator (See ITU-T G.7710)." + ::= { optIfODUkTtpConfigEntry 7 } + +optIfODUkTtpDEGM OBJECT-TYPE + SYNTAX OptIfDEGM + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Indicates the threshold level for declaring a Degraded Signal + defect (dDEG). A dDEG shall be declared if optIfODUkDEGM + consecutive bad PM Seconds are detected. + This object is only applicable to the sink function, i.e., + only when optIfODUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfODUkDirectionality has the value source(2). + The default value of this object is 7 (See ITU-T G.7710)." + ::= { optIfODUkTtpConfigEntry 8 } + +optIfODUkTtpCurrentStatus OBJECT-TYPE + SYNTAX BITS { + oci(0), + lck(1), + tim(2), + deg(3), + bdi(4), + ssf(5) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the defect condition of the entity, if any. + This object is only applicable to the sink function, i.e., + only when optIfODUkDirectionality has the value sink(1) + or bidirectional(3). It must not be instantiated in rows + where optIfODUkDirectionality has the value source(2)." + ::= { optIfODUkTtpConfigEntry 9 } + +-- ODUk Position Sequence table + +optIfODUkPositionSeqTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfODUkPositionSeqEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of ODUk Position Sequence information." + ::= { optIfODUk 3 } + +optIfODUkPositionSeqEntry OBJECT-TYPE + SYNTAX OptIfODUkPositionSeqEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains ODUk position sequence + information of an ODUk interface. The ODUk interface + is identified by the ifIndex. Associated with each + ODUk interface there may be one of more conceptual + rows in the optIfODUkPositionSeqTable. Each row + represents a TCM or GCC12 access function within the + associated ODUk interface. Rows of the + optIfODUkPositionSeqTable table are created/deleted + as the result of the creation/deletion of the optIfODUkT + or optIfGCC12 entities." + INDEX { ifIndex, optIfODUkPositionSeqIndex } + ::= { optIfODUkPositionSeqTable 1 } + +OptIfODUkPositionSeqEntry ::= + SEQUENCE { + optIfODUkPositionSeqIndex Unsigned32, + optIfODUkPositionSeqPosition Unsigned32, + optIfODUkPositionSeqPointer RowPointer + } + +optIfODUkPositionSeqIndex OBJECT-TYPE + SYNTAX Unsigned32 (1..4294967295) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This variable identifies a row in the + optIfODUkPositionSeqTable Table. + Each row of the optIfODUkPositionSeqTable Table + represents a TCM or GCC12 access function within the + associated ODUk interface." + ::= { optIfODUkPositionSeqEntry 1 } + +optIfODUkPositionSeqPosition OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This variable indicates the position of the TCM or + GCC12 access function within the sequence of TCMs & + GCC12 access functions of the associated ODUk + interface. The TCM or GCC12 presented by this row is + referenced by the optIfODUkPositionSeqPointer variable." + ::= { optIfODUkPositionSeqEntry 2 } + +optIfODUkPositionSeqPointer OBJECT-TYPE + SYNTAX RowPointer + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This variable identifies the TCM or GCC12 access function + by pointing to the corresponding optIfODUkT or optIfGCC12 + entity." + ::= { optIfODUkPositionSeqEntry 3 } + +-- ODUk Non-intrusive monitoring (Nim) config table + +optIfODUkNimConfigTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfODUkNimConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of ODUkNim configuration information." + ::= { optIfODUk 4 } + +optIfODUkNimConfigEntry OBJECT-TYPE + SYNTAX OptIfODUkNimConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains ODUkNim configuration + information of an interface. Each instance must + correspond to an instance of optIfODUkConfigEntry + for which optIfODUkTtpPresent has the value false(2). + + Instances of this conceptual row persist across + agent restarts, and read-create columns other + than the status column may be modified while the + row is active." + INDEX { ifIndex, optIfODUkNimDirectionality } + ::= { optIfODUkNimConfigTable 1 } + +OptIfODUkNimConfigEntry ::= + SEQUENCE { + optIfODUkNimDirectionality OptIfSinkOrSource, + optIfODUkNimDAPIExpected OptIfExDAPI, + optIfODUkNimSAPIExpected OptIfExSAPI, + optIfODUkNimTraceIdentifierAccepted OptIfAcTI, + optIfODUkNimTIMDetMode OptIfTIMDetMode, + optIfODUkNimTIMActEnabled TruthValue, + optIfODUkNimDEGThr OptIfDEGThr, + optIfODUkNimDEGM OptIfDEGM, + optIfODUkNimCurrentStatus BITS, + optIfODUkNimRowStatus RowStatus + } + +optIfODUkNimDirectionality OBJECT-TYPE + SYNTAX OptIfSinkOrSource + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Specifies the monitor point for the ODUk Path non-intrusive + monitoring function. The value source(2) is not allowed + if the corresponding instance of optIfODUkDirectionality + has the value sink(1), and the value sink(1) is not allowed + if the corresponding instance of optIfODUkDirectionality + has the value source(2). Either the value sink(1) or + source(2) is allowed if the corresponding instance of + optIfODUkDirectionality has the value bidirectional(3). + + The value sink(1) means monitoring at the sink direction + path signal of the ODUk CTP. + + The value source(2) means monitoring at the source direction + path signal of the ODUk CTP. Monitoring the source direction + of an ODUk CTP is necessary in those cases where the ODUk CTP + is at an SNCP (Subnetwork Connection Protection) end (e.g., see + Figure I.1.2/G.874.1). If one would like to get the performance + of the protected connection, one cannot use the NIM function + at both ODUk CTP sinks (before the matrix), instead one should + monitor the signal at the source ODUk CTP after the matrix." + ::= { optIfODUkNimConfigEntry 1 } + +optIfODUkNimDAPIExpected OBJECT-TYPE + SYNTAX OptIfExDAPI + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The DAPI expected by the receiver. + This object has no effect if optIfODUkNimTIMDetMode has + the value off(1) or sapi(3)." + ::= { optIfODUkNimConfigEntry 2 } + +optIfODUkNimSAPIExpected OBJECT-TYPE + SYNTAX OptIfExSAPI + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The SAPI expected by the receiver. + This object has no effect if optIfODUkNimTIMDetMode has + the value off(1) or dapi(2)." + ::= { optIfODUkNimConfigEntry 3 } + +optIfODUkNimTraceIdentifierAccepted OBJECT-TYPE + SYNTAX OptIfAcTI + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The actual trace identifier accepted. The value of + this object is unspecified if optIfODUkNimCurrentStatus + has any of the bit positions oci(0), lck(1), or ssf(5) + set or if optIfODUkNimRowStatus has any value other + than active(1)." + ::= { optIfODUkNimConfigEntry 4 } + +optIfODUkNimTIMDetMode OBJECT-TYPE + SYNTAX OptIfTIMDetMode + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates the mode of the Trace Identifier Mismatch (TIM) + Detection function." + ::= { optIfODUkNimConfigEntry 5 } + +optIfODUkNimTIMActEnabled OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates whether the Trace Identifier Mismatch (TIM) + Consequent Action function is enabled." + ::= { optIfODUkNimConfigEntry 6 } + +optIfODUkNimDEGThr OBJECT-TYPE + SYNTAX OptIfDEGThr + UNITS "percentage" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates the threshold level for declaring a performance + monitoring (PM) Second to be bad. A PM Second is declared bad + if the percentage of detected errored blocks in that second is + greater than or equal to optIfODUkNimDEGThr." + ::= { optIfODUkNimConfigEntry 7 } + +optIfODUkNimDEGM OBJECT-TYPE + SYNTAX OptIfDEGM + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates the threshold level for declaring a Degraded Signal + defect (dDEG). A dDEG shall be declared if optIfODUkNimDEGM + consecutive bad PM Seconds are detected." + ::= { optIfODUkNimConfigEntry 8 } + +optIfODUkNimCurrentStatus OBJECT-TYPE + SYNTAX BITS { + oci(0), + lck(1), + tim(2), + deg(3), + bdi(4), + ssf(5) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the defect condition of the entity, if + any. The value of this object is unspecified if + optIfODUkNimRowStatus has any value other than + active(1)." + ::= { optIfODUkNimConfigEntry 9 } + +optIfODUkNimRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This columnar object is used for creating and deleting + a conceptual row of the optIfODUkNim config table. + It is used to model the activateNim and deactivateNim + operations of an OTUk_CTP for non-intrusive monitoring + control as defined in G.874.1. Setting RowStatus to + createAndGo or createAndWait implies activateNim. + Setting RowStatus to destroy implies deactivateNim." + ::= { optIfODUkNimConfigEntry 10 } + +-- GCC12 config table + +optIfGCC12ConfigTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfGCC12ConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of GCC12 configuration information. + The GCC function processes the GCC overhead bytes passing + through them but leave the remainder of the ODUk overhead + and payload data alone." + ::= { optIfODUk 5 } + +optIfGCC12ConfigEntry OBJECT-TYPE + SYNTAX OptIfGCC12ConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains GCC12 configuration + information of an interface. Each instance must + correspond to an instance of optIfODUkConfigEntry. + Separate instances providing GCC1-only access and + GCC2-only access may exist for a given ifIndex value, + or a single instance providing GCC1 + GCC2 may exist, + but a GCC1 + GCC2 instance may not coexist with a + GCC1-only or GCC2-only instance. + + Instances of this conceptual row persist across agent + restarts." + INDEX { ifIndex, optIfGCC12Codirectional, optIfGCC12GCCAccess } + ::= { optIfGCC12ConfigTable 1 } + + +OptIfGCC12ConfigEntry ::= + SEQUENCE { + optIfGCC12Codirectional TruthValue, + optIfGCC12GCCAccess INTEGER, + optIfGCC12GCCPassThrough TruthValue, + optIfGCC12Application SnmpAdminString, + optIfGCC12RowStatus RowStatus + } + +optIfGCC12Codirectional OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Indicates the directionality of the GCC12 termination with + respect to the associated ODUk CTP. The value true(1) means + that the sink part of the GCC12 extracts COMMS data from the + signal at the input to the ODUk CTP sink and the source part + of the GCC12 inserts COMMS data into the signal at the output + of the ODUk CTP source. The value false(2) means that the + sink part of the GCC12 extracts COMMS data from the signal at + the output of the ODUk CTP source and the source part of the + GCC12 inserts COMMS data into the signal at the input of the + ODUk CTP sink. This attribute may assume either value when + the corresponding instance of optIfODUkTtpPresent has the + value false(2). When the value of the corresponding instance + of optIfODUkTtpPresent is true(1) then the only value allowed + for this attribute is true(1)." + ::= { optIfGCC12ConfigEntry 1 } + +optIfGCC12GCCAccess OBJECT-TYPE + SYNTAX INTEGER { + gcc1 (1), + gcc2 (2), + gcc1and2 (3) + } + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Indicates the GCC access represented by the entity." + ::= { optIfGCC12ConfigEntry 2 } + +optIfGCC12GCCPassThrough OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Controls whether the selected GCC overhead bytes are passed + through or modified. The value true(1) means that the selected + GCC overhead bytes are passed through unmodified from the ODUk + CTP input to the ODUk CTP output. The value false(2) means that + the selected GCC overhead bytes are set to zero at the ODUk CTP + output after the extraction of the COMMS data. This object has + no effect if the corresponding instance of optIfODUkTtpPresent + has the value true(1). + + The value of this object may not be changed when + optIfGCC12RowStatus has the value active(1)." + ::= { optIfGCC12ConfigEntry 3 } + +optIfGCC12Application OBJECT-TYPE + SYNTAX SnmpAdminString + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates the application transported by the GCC12 entity. + Example applications are ECC, User data channel. + + The value of this object may not be changed when + optIfGCC12RowStatus has the value active(1)." + ::= { optIfGCC12ConfigEntry 4 } + +optIfGCC12RowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This columnar object is used for creating and deleting + a conceptual row of the optIfGCC12 config table. It is + used to model the addGCC12Access and removeGCC12Access + operations of an ODUk_CTP or ODUk_TTP for GCC12 access + control as defined in G.874.1. Setting RowStatus to + createAndGo or createAndWait implies addGCC12Access. + Setting RowStatus to destroy implies removeGCC12Access. + Successful addition/removal of the GCC12 access function + will result in updating the + optIfODUkPositionSeqCurrentSize variable and the + optIfODUkPositionSeqTable table of the associated + ODUk entry in the optIfODUkConfigTable." + ::= { optIfGCC12ConfigEntry 5 } + +-- the optIfODUkT group +-- This group handles the configuration information +-- for the ODUkT layers. + +-- ODUkT config table + +optIfODUkTConfigTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfODUkTConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of ODUkT configuration information." + ::= { optIfODUkT 1 } + +optIfODUkTConfigEntry OBJECT-TYPE + SYNTAX OptIfODUkTConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains ODUkT configuration + information of an interface. Each instance must + correspond to an instance of optIfODUkConfigEntry. + Rows in this table are mutually exclusive with rows + in the ODUkT NIM config table -- in other words, this + row object may not be instantiated for a given pair + of ifIndex and TCM field values if a corresponding + instance of optIfODUkTNimConfigEntry already exists. + + Instances of this conceptual row persist across agent + restarts. Except where noted otherwise, read-create + columns other than the status column may be modified + while the row is active." + INDEX { ifIndex, optIfODUkTTcmField, optIfODUkTCodirectional } + ::= { optIfODUkTConfigTable 1 } + +OptIfODUkTConfigEntry ::= + SEQUENCE { + optIfODUkTTcmField Unsigned32, + optIfODUkTCodirectional TruthValue, + optIfODUkTTraceIdentifierTransmitted OptIfTxTI, + optIfODUkTDAPIExpected OptIfExDAPI, + optIfODUkTSAPIExpected OptIfExSAPI, + optIfODUkTTraceIdentifierAccepted OptIfAcTI, + optIfODUkTTIMDetMode OptIfTIMDetMode, + optIfODUkTTIMActEnabled TruthValue, + optIfODUkTDEGThr OptIfDEGThr, + optIfODUkTDEGM OptIfDEGM, + optIfODUkTSinkMode INTEGER, + optIfODUkTSinkLockSignalAdminState INTEGER, + optIfODUkTSourceLockSignalAdminState INTEGER, + optIfODUkTCurrentStatus BITS, + optIfODUkTRowStatus RowStatus + } + + +optIfODUkTTcmField OBJECT-TYPE + SYNTAX Unsigned32 (1..6) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Indicates the tandem connection monitoring + field of the ODUk OH. Valid values are + integers from 1 to 6." + ::= { optIfODUkTConfigEntry 1 } + +optIfODUkTCodirectional OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Indicates the directionality of the ODUkT termination point with + respect to the associated ODUk CTP. The value true(1) means + that the sink part of the ODUkT TP extracts TCM data from the + signal at the input to the ODUk CTP sink and the source part + of the ODUkT TP inserts TCM data into the signal at the output + of the ODUk CTP source. The value false(2) means that the + sink part of the ODUkT TP extracts TCM data from the signal at + the output of the ODUk CTP source and the source part of the + ODUkT TP inserts TCM data into the signal at the input of the + ODUk CTP sink. This attribute may assume either value when + the corresponding instance of optIfODUkTtpPresent has the + value false(2). When the value of the corresponding instance + of optIfODUkTtpPresent is true(1) then the only value allowed + for this attribute is true(1)." + ::= { optIfODUkTConfigEntry 2 } + +optIfODUkTTraceIdentifierTransmitted OBJECT-TYPE + SYNTAX OptIfTxTI + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The trace identifier transmitted. + This object is applicable only to the following three cases. + (i) optIfODUkDirectionality has the value bidirectional(3), or + (ii) optIfODUkDirectionality has the value sink(1) and + optIfODUkTCodirectional has the value false(2), or + (iii) optIfODUkDirectionality has the value source(3) and + optIfODUkTCodirectional has the value true(1). + It must not be instantiated in rows for all other cases." + ::= { optIfODUkTConfigEntry 3 } + +optIfODUkTDAPIExpected OBJECT-TYPE + SYNTAX OptIfExDAPI + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The DAPI expected by the receiver. + This object is applicable only to the following three cases. + (i) optIfODUkDirectionality has the value bidirectional(3), or + (ii) optIfODUkDirectionality has the value sink(1) and + optIfODUkTCodirectional has the value true(1), or + (iii) optIfODUkDirectionality has the value source(3) and + optIfODUkTCodirectional has the value false(2). + It must not be instantiated in rows for all other cases. + This object has no effect when optIfODUkTTIMDetMode has + the value off(1)." + ::= { optIfODUkTConfigEntry 4 } + +optIfODUkTSAPIExpected OBJECT-TYPE + SYNTAX OptIfExSAPI + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The SAPI expected by the receiver. + This object is applicable only to the following three cases. + (i) optIfODUkDirectionality has the value bidirectional(3), or + (ii) optIfODUkDirectionality has the value sink(1) and + optIfODUkTCodirectional has the value true(1), or + (iii) optIfODUkDirectionality has the value source(3) and + optIfODUkTCodirectional has the value false(2). + It must not be instantiated in rows for all other cases. + This object has no effect when optIfODUkTTIMDetMode has + the value off(1)." + ::= { optIfODUkTConfigEntry 5 } + +optIfODUkTTraceIdentifierAccepted OBJECT-TYPE + SYNTAX OptIfAcTI + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The actual trace identifier accepted. + This object is applicable only to the following three cases. + (i) optIfODUkDirectionality has the value bidirectional(3), or + (ii) optIfODUkDirectionality has the value sink(1) and + optIfODUkTCodirectional has the value true(1), or + (iii) optIfODUkDirectionality has the value source(3) and + optIfODUkTCodirectional has the value false(2). + It must not be instantiated in rows for all other cases. + The value of this object is unspecified when + optIfODUkTCurrentStatus indicates a near-end defect + (i.e., oci(0), lck(1), ssf(5)) that prevents extraction + of the trace message." + ::= { optIfODUkTConfigEntry 6 } + +optIfODUkTTIMDetMode OBJECT-TYPE + SYNTAX OptIfTIMDetMode + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates the mode of the Trace Identifier Mismatch (TIM) + Detection function. + This object is applicable only to the following three cases. + (i) optIfODUkDirectionality has the value bidirectional(3), or + (ii) optIfODUkDirectionality has the value sink(1) and + optIfODUkTCodirectional has the value true(1), or + (iii) optIfODUkDirectionality has the value source(3) and + optIfODUkTCodirectional has the value false(2). + It must not be instantiated in rows for all other cases. + The default value of this object is off(1)." + ::= { optIfODUkTConfigEntry 7 } + +optIfODUkTTIMActEnabled OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates whether the Trace Identifier Mismatch (TIM) + Consequent Action function is enabled. + This object is applicable only to the following three cases. + (i) optIfODUkDirectionality has the value bidirectional(3), or + (ii) optIfODUkDirectionality has the value sink(1) and + optIfODUkTCodirectional has the value true(1), or + (iii) optIfODUkDirectionality has the value source(3) and + optIfODUkTCodirectional has the value false(2). + It must not be instantiated in rows for all other cases. + This object has no effect when optIfODUkTTIMDetMode has + the value off(1). + The default value of this object is false(2)." + ::= { optIfODUkTConfigEntry 8 } + +optIfODUkTDEGThr OBJECT-TYPE + SYNTAX OptIfDEGThr + UNITS "percentage" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates the threshold level for declaring a performance + monitoring (PM) Second to be bad. A PM Second is declared bad if + the percentage of detected errored blocks in that second is + greater than or equal to optIfODUkTDEGThr. + This object is applicable only to the following three cases. + (i) optIfODUkDirectionality has the value bidirectional(3), or + (ii) optIfODUkDirectionality has the value sink(1) and + optIfODUkTCodirectional has the value true(1), or + (iii) optIfODUkDirectionality has the value source(3) and + optIfODUkTCodirectional has the value false(2). + It must not be instantiated in rows for all other cases. + The default value of this object is Severely Errored Second + (SES) Estimator (See ITU-T G.7710)." + ::= { optIfODUkTConfigEntry 9 } + +optIfODUkTDEGM OBJECT-TYPE + SYNTAX OptIfDEGM + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates the threshold level for declaring a Degraded Signal + defect (dDEG). A dDEG shall be declared if optIfODUkTDEGM + consecutive bad PM Seconds are detected. + This object is applicable only to the following three cases. + (i) optIfODUkDirectionality has the value bidirectional(3), or + (ii) optIfODUkDirectionality has the value sink(1) and + optIfODUkTCodirectional has the value true(1), or + (iii) optIfODUkDirectionality has the value source(3) and + optIfODUkTCodirectional has the value false(2). + It must not be instantiated in rows for all other cases. + The default value of this object is 7 (See ITU-T G.7710)." + ::= { optIfODUkTConfigEntry 10 } + +optIfODUkTSinkMode OBJECT-TYPE + SYNTAX INTEGER { + operational (1), + monitor (2) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This variable specifies the TCM mode at the entity. + The value operational(1) means that TCM Overhead (TCMOH) + processes (see ITU-T G.798) shall be + performed and consequent actions for AIS, Trail + Signal Fail (TSF), Trail Signal Degraded (TSD) shall be + initiated in case of defects. + The value monitor(2) means that TCMOH processes shall be + performed but consequent actions for AIS, Trail + Server Failure (TSF), Trail Server Degraded (TSD) shall _not_ be + initiated in case of defects. + This object is applicable only when the value of + optIfODUkTtpPresent is false(2) and also either one of the + following three cases holds: + (i) optIfODUkDirectionality has the value bidirectional(3), or + (ii) optIfODUkDirectionality has the value sink(1) and + optIfODUkTCodirectional has the value true(1), or + (iii) optIfODUkDirectionality has the value source(3) and + optIfODUkTCodirectional has the value false(2). + It must not be instantiated in rows for all other cases." + ::= { optIfODUkTConfigEntry 11 } + +optIfODUkTSinkLockSignalAdminState OBJECT-TYPE + SYNTAX INTEGER { + locked(1), + normal(2) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Provides the capability to provision the LOCK signal, which + is one of the ODUk maintenance signals, at the ODUKT sink. When + a Tandem Connection endpoint is set to admin state locked, + it inserts the ODUk-LCK signal in the sink direction. + + This object is applicable only when the value of + optIfODUkTtpPresent is false(2) and also either one of the + following three cases holds: + (i) optIfODUkDirectionality has the value bidirectional(3), or + (ii) optIfODUkDirectionality has the value sink(1) and + optIfODUkTCodirectional has the value true(1), or + (iii) optIfODUkDirectionality has the value source(3) and + optIfODUkTCodirectional has the value false(2). + It must not be instantiated in rows for all other cases." + ::= { optIfODUkTConfigEntry 12 } + +optIfODUkTSourceLockSignalAdminState OBJECT-TYPE + SYNTAX INTEGER { + locked(1), + normal(2) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Provides the capability to provision the LOCK signal, which + is one of the ODUk maintenance signals, at the source. + When a Tandem Connection endpoint is set to admin state + locked, it inserts the ODUk-LCK signal in the source + direction. + This object is applicable only when either one of the + following three cases holds: + (i) optIfODUkDirectionality has the value bidirectional(3), or + (ii) optIfODUkDirectionality has the value sink(1) and + optIfODUkTCodirectional has the value false(2), or + (iii) optIfODUkDirectionality has the value source(3) and + optIfODUkTCodirectional has the value true(1). + It must not be instantiated in rows for all other cases." + ::= { optIfODUkTConfigEntry 13 } + +optIfODUkTCurrentStatus OBJECT-TYPE + SYNTAX BITS { + oci(0), + lck(1), + tim(2), + deg(3), + bdi(4), + ssf(5) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the defect condition of the entity, if any. + This object is applicable only when either one of the + following three cases holds: + (i) optIfODUkDirectionality has the value bidirectional(3), or + (ii) optIfODUkDirectionality has the value sink(1) and + optIfODUkTCodirectional has the value true(1), or + (iii) optIfODUkDirectionality has the value source(3) and + optIfODUkTCodirectional has the value false(2). + It must not be instantiated in rows for all other cases." + ::= { optIfODUkTConfigEntry 14 } + +optIfODUkTRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This columnar object is used for creating and deleting a + conceptual row of the optIfODUkT config table. + It is used to model the addTCM and removeTCM operations of an + ODUk_CTP or ODUk_TTP for Tandem connection monitoring as defined + in ITU-T G.874.1. + Setting RowStatus to createAndGo or createAndWait implies addTCM. + Setting RowStatus to destroy implies removeTCM. + Successful addition/removal of TCM will result in updating the + optIfODUkTcmFieldsInUse and optIfODUkPositionSeqCurrentSize + variables and the optIfODUkPositionSeqTable table of the + associated ODUk entry in the optIfODUkConfigTable." + ::= { optIfODUkTConfigEntry 15 } + +-- ODUkT Non-intrusive monitoring (Nim) config table + +optIfODUkTNimConfigTable OBJECT-TYPE + SYNTAX SEQUENCE OF OptIfODUkTNimConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of ODUkTNim configuration information." + ::= { optIfODUkT 2 } + +optIfODUkTNimConfigEntry OBJECT-TYPE + SYNTAX OptIfODUkTNimConfigEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row that contains ODUkTNim configuration + information of an interface. Each instance must + correspond to an instance of optIfODUkConfigEntry. + Rows in this table are mutually exclusive with rows + in the ODUkT config table -- in other words, this + row object may not be instantiated for a given pair + of ifIndex and TCM field values if a corresponding + instance of optIfODUkTConfigEntry already exists. + + Instances of this conceptual row persist across + agent restarts, and read-create columns other + than the status column may be modified while the + row is active." + INDEX {ifIndex, optIfODUkTNimTcmField, optIfODUkTNimDirectionality} + ::= { optIfODUkTNimConfigTable 1 } + +OptIfODUkTNimConfigEntry ::= + SEQUENCE { + optIfODUkTNimTcmField Unsigned32, + optIfODUkTNimDirectionality OptIfSinkOrSource, + optIfODUkTNimDAPIExpected OptIfExDAPI, + optIfODUkTNimSAPIExpected OptIfExSAPI, + optIfODUkTNimTraceIdentifierAccepted OptIfAcTI, + optIfODUkTNimTIMDetMode OptIfTIMDetMode, + optIfODUkTNimTIMActEnabled TruthValue, + optIfODUkTNimDEGThr OptIfDEGThr, + optIfODUkTNimDEGM OptIfDEGM, + optIfODUkTNimCurrentStatus BITS, + optIfODUkTNimRowStatus RowStatus + } + +optIfODUkTNimTcmField OBJECT-TYPE + SYNTAX Unsigned32 (1..6) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Indicates the tandem connection monitoring + field of the ODUk OH on which non-intrusive monitoring + is performed. Valid values are + integers from 1 to 6." + ::= { optIfODUkTNimConfigEntry 1 } + +optIfODUkTNimDirectionality OBJECT-TYPE + SYNTAX OptIfSinkOrSource + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Specifies the monitor point for the ODUk TCM non-intrusive + monitoring function. The value source(2) is not allowed + if the corresponding instance of optIfODUkDirectionality + has the value sink(1), and the value sink(1) is not allowed + if the corresponding instance of optIfODUkDirectionality + has the value source(2). Either the value sink(1) or + source(2) is allowed if the corresponding instance of + optIfODUkDirectionality has the value bidirectional(3). + The value sink(1) means monitoring at the sink direction + TCM signal of the ODUk CTP. + The value source(2) means monitoring at the source direction + path signal of the ODUk CTP." + ::= { optIfODUkTNimConfigEntry 2 } + +optIfODUkTNimDAPIExpected OBJECT-TYPE + SYNTAX OptIfExDAPI + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The DAPI expected by the receiver. + This object has no effect if optIfODUkTNimTIMDetMode has + the value off(1) or sapi(3)." + ::= { optIfODUkTNimConfigEntry 3 } + +optIfODUkTNimSAPIExpected OBJECT-TYPE + SYNTAX OptIfExSAPI + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The SAPI expected by the receiver. + This object has no effect if optIfODUkTNimTIMDetMode has + the value off(1) or dapi(2)." + + ::= { optIfODUkTNimConfigEntry 4 } + +optIfODUkTNimTraceIdentifierAccepted OBJECT-TYPE + SYNTAX OptIfAcTI + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The actual trace identifier accepted. The value of + this object is unspecified if optIfODUkTNimCurrentStatus + has any of the bit positions oci(0), lck(1), or ssf(5) + set or if optIfODUkTNimRowStatus has any value other + than active(1)." + ::= { optIfODUkTNimConfigEntry 5 } + +optIfODUkTNimTIMDetMode OBJECT-TYPE + SYNTAX OptIfTIMDetMode + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates the mode of the Trace Identifier Mismatch (TIM) + Detection function." + ::= { optIfODUkTNimConfigEntry 6 } + +optIfODUkTNimTIMActEnabled OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates whether the Trace Identifier Mismatch (TIM) + Consequent Action function is enabled." + ::= { optIfODUkTNimConfigEntry 7 } + +optIfODUkTNimDEGThr OBJECT-TYPE + SYNTAX OptIfDEGThr + UNITS "percentage" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates the threshold level for declaring a performance + monitoring (PM) Second to be bad. A PM Second is declared bad if + the percentage of detected errored blocks in that second is + greater than or equal to optIfODUkTNimDEGThr." + ::= { optIfODUkTNimConfigEntry 8 } + +optIfODUkTNimDEGM OBJECT-TYPE + SYNTAX OptIfDEGM + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates the threshold level for declaring a Degraded Signal + defect (dDEG). A dDEG shall be declared if optIfODUkTNimDEGM + consecutive bad PM Seconds are detected." + ::= { optIfODUkTNimConfigEntry 9 } + +optIfODUkTNimCurrentStatus OBJECT-TYPE + SYNTAX BITS { + oci(0), + lck(1), + tim(2), + deg(3), + bdi(4), + ssf(5) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the defect condition of the entity, if any. + The value of this object is unspecified if + optIfODUkTNimRowStatus has any value other than + active(1)." + ::= { optIfODUkTNimConfigEntry 10 } + +optIfODUkTNimRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This columnar object is used for creating and deleting a + conceptual row of the optIfODUkTNim config table. + It is used to model the addTCM and removeTCM operations of an + ODUk_CTP or ODUk_TTP for non-intrusive Tandem connection + monitoring as defined in ITU-T G.874.1. + Setting RowStatus to createAndGo or createAndWait implies addTCM. + Setting RowStatus to destroy implies removeTCM. + Successful addition/removal of Nim TCM will result in updating + the optIfODUkPositionSeqCurrentSize variable and the + optIfODUkPositionSeqTable table of the associated ODUk entry + in the optIfODUkConfigTable." + ::= { optIfODUkTNimConfigEntry 11 } + +-- units of conformance + +optIfOTMnGroup OBJECT-GROUP + OBJECTS { + optIfOTMnOrder, + optIfOTMnReduced, + optIfOTMnBitRates, + optIfOTMnInterfaceType, + optIfOTMnTcmMax, + optIfOTMnOpticalReach + } + STATUS current + DESCRIPTION + "A collection of OTMn structure information objects." + ::= { optIfGroups 1 } + +optIfPerfMonGroup OBJECT-GROUP + OBJECTS { + optIfPerfMonCurrentTimeElapsed, + optIfPerfMonCurDayTimeElapsed, + optIfPerfMonIntervalNumIntervals, + optIfPerfMonIntervalNumInvalidIntervals + } + STATUS current + DESCRIPTION + "A collection of performance monitoring interval objects." + ::= { optIfGroups 2 } + +optIfOTSnCommonGroup OBJECT-GROUP + OBJECTS { + optIfOTSnDirectionality + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to all OTSn interfaces." + ::= { optIfGroups 3 } + +optIfOTSnSourceGroupFull OBJECT-GROUP + OBJECTS { + optIfOTSnTraceIdentifierTransmitted + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to full-functionality/IaDI OTSn + interfaces that support source functions." + ::= { optIfGroups 4 } + +optIfOTSnAPRStatusGroup OBJECT-GROUP + OBJECTS { + optIfOTSnAprStatus + } + STATUS current + DESCRIPTION + "A collection of objects applicable to + OTSn interfaces that support Automatic + Power Reduction functions." + ::= { optIfGroups 5 } + +optIfOTSnAPRControlGroup OBJECT-GROUP + OBJECTS { + optIfOTSnAprControl + } + STATUS current + DESCRIPTION + "A collection of objects applicable to + OTSn interfaces that provide Automatic + Power Reduction control functions." + ::= { optIfGroups 6 } + +optIfOTSnSinkGroupBasic OBJECT-GROUP + OBJECTS { + optIfOTSnCurrentStatus + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to all OTSn interfaces that + support sink functions." + ::= { optIfGroups 7 } + +optIfOTSnSinkGroupFull OBJECT-GROUP + OBJECTS { + optIfOTSnDAPIExpected, + optIfOTSnSAPIExpected, + optIfOTSnTraceIdentifierAccepted, + optIfOTSnTIMDetMode, + optIfOTSnTIMActEnabled + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to full-functionality/IaDI OTSn + interfaces that support sink functions." + ::= { optIfGroups 8 } + +optIfOTSnSinkPreOtnPMGroup OBJECT-GROUP + OBJECTS { + optIfOTSnSinkCurrentSuspectedFlag, + optIfOTSnSinkCurrentInputPower, + optIfOTSnSinkCurrentLowInputPower, + optIfOTSnSinkCurrentHighInputPower, + optIfOTSnSinkCurrentOutputPower, + optIfOTSnSinkCurrentLowOutputPower, + optIfOTSnSinkCurrentHighOutputPower, + optIfOTSnSinkIntervalSuspectedFlag, + optIfOTSnSinkIntervalLastInputPower, + optIfOTSnSinkIntervalLowInputPower, + optIfOTSnSinkIntervalHighInputPower, + optIfOTSnSinkIntervalLastOutputPower, + optIfOTSnSinkIntervalLowOutputPower, + optIfOTSnSinkIntervalHighOutputPower, + optIfOTSnSinkCurDaySuspectedFlag, + optIfOTSnSinkCurDayLowInputPower, + optIfOTSnSinkCurDayHighInputPower, + optIfOTSnSinkCurDayLowOutputPower, + optIfOTSnSinkCurDayHighOutputPower, + optIfOTSnSinkPrevDaySuspectedFlag, + optIfOTSnSinkPrevDayLastInputPower, + optIfOTSnSinkPrevDayLowInputPower, + optIfOTSnSinkPrevDayHighInputPower, + optIfOTSnSinkPrevDayLastOutputPower, + optIfOTSnSinkPrevDayLowOutputPower, + optIfOTSnSinkPrevDayHighOutputPower + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + objects applicable to OTSn interfaces that + support sink functions." + ::= { optIfGroups 9 } + +optIfOTSnSinkPreOtnPMThresholdGroup OBJECT-GROUP + OBJECTS { + optIfOTSnSinkCurrentLowerInputPowerThreshold, + optIfOTSnSinkCurrentUpperInputPowerThreshold, + optIfOTSnSinkCurrentLowerOutputPowerThreshold, + optIfOTSnSinkCurrentUpperOutputPowerThreshold + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + threshold objects applicable to OTSn interfaces + that support sink functions." + ::= { optIfGroups 10 } + +optIfOTSnSourcePreOtnPMGroup OBJECT-GROUP + OBJECTS { + optIfOTSnSrcCurrentSuspectedFlag, + optIfOTSnSrcCurrentOutputPower, + optIfOTSnSrcCurrentLowOutputPower, + optIfOTSnSrcCurrentHighOutputPower, + optIfOTSnSrcCurrentInputPower, + optIfOTSnSrcCurrentLowInputPower, + optIfOTSnSrcCurrentHighInputPower, + optIfOTSnSrcIntervalSuspectedFlag, + optIfOTSnSrcIntervalLastOutputPower, + optIfOTSnSrcIntervalLowOutputPower, + optIfOTSnSrcIntervalHighOutputPower, + optIfOTSnSrcIntervalLastInputPower, + optIfOTSnSrcIntervalLowInputPower, + optIfOTSnSrcIntervalHighInputPower, + optIfOTSnSrcCurDaySuspectedFlag, + optIfOTSnSrcCurDayLowOutputPower, + optIfOTSnSrcCurDayHighOutputPower, + optIfOTSnSrcCurDayLowInputPower, + optIfOTSnSrcCurDayHighInputPower, + optIfOTSnSrcPrevDaySuspectedFlag, + optIfOTSnSrcPrevDayLastOutputPower, + optIfOTSnSrcPrevDayLowOutputPower, + optIfOTSnSrcPrevDayHighOutputPower, + optIfOTSnSrcPrevDayLastInputPower, + optIfOTSnSrcPrevDayLowInputPower, + optIfOTSnSrcPrevDayHighInputPower + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + objects applicable to OTSn interfaces that + support source functions." + ::= { optIfGroups 11 } + +optIfOTSnSourcePreOtnPMThresholdGroup OBJECT-GROUP + OBJECTS { + optIfOTSnSrcCurrentLowerOutputPowerThreshold, + optIfOTSnSrcCurrentUpperOutputPowerThreshold, + optIfOTSnSrcCurrentLowerInputPowerThreshold, + optIfOTSnSrcCurrentUpperInputPowerThreshold + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + threshold objects applicable to OTSn interfaces + that support source functions." + ::= { optIfGroups 12 } + +optIfOMSnCommonGroup OBJECT-GROUP + OBJECTS { + optIfOMSnDirectionality + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to all OMSn interfaces." + ::= { optIfGroups 13 } + +optIfOMSnSinkGroupBasic OBJECT-GROUP + OBJECTS { + optIfOMSnCurrentStatus + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to all OMSn interfaces that + support sink functions." + ::= { optIfGroups 14 } + +optIfOMSnSinkPreOtnPMGroup OBJECT-GROUP + OBJECTS { + optIfOMSnSinkCurrentSuspectedFlag, + optIfOMSnSinkCurrentAggregatedInputPower, + optIfOMSnSinkCurrentLowAggregatedInputPower, + optIfOMSnSinkCurrentHighAggregatedInputPower, + optIfOMSnSinkCurrentOutputPower, + optIfOMSnSinkCurrentLowOutputPower, + optIfOMSnSinkCurrentHighOutputPower, + optIfOMSnSinkIntervalSuspectedFlag, + optIfOMSnSinkIntervalLastAggregatedInputPower, + optIfOMSnSinkIntervalLowAggregatedInputPower, + optIfOMSnSinkIntervalHighAggregatedInputPower, + optIfOMSnSinkIntervalLastOutputPower, + optIfOMSnSinkIntervalLowOutputPower, + optIfOMSnSinkIntervalHighOutputPower, + optIfOMSnSinkCurDaySuspectedFlag, + optIfOMSnSinkCurDayLowAggregatedInputPower, + optIfOMSnSinkCurDayHighAggregatedInputPower, + optIfOMSnSinkCurDayLowOutputPower, + optIfOMSnSinkCurDayHighOutputPower, + optIfOMSnSinkPrevDaySuspectedFlag, + optIfOMSnSinkPrevDayLastAggregatedInputPower, + optIfOMSnSinkPrevDayLowAggregatedInputPower, + optIfOMSnSinkPrevDayHighAggregatedInputPower, + optIfOMSnSinkPrevDayLastOutputPower, + optIfOMSnSinkPrevDayLowOutputPower, + optIfOMSnSinkPrevDayHighOutputPower + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + objects applicable to OMSn interfaces that + support sink functions." + ::= { optIfGroups 15 } + +optIfOMSnSinkPreOtnPMThresholdGroup OBJECT-GROUP + OBJECTS { + optIfOMSnSinkCurrentLowerInputPowerThreshold, + optIfOMSnSinkCurrentUpperInputPowerThreshold, + optIfOMSnSinkCurrentLowerOutputPowerThreshold, + optIfOMSnSinkCurrentUpperOutputPowerThreshold + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + threshold objects applicable to OMSn interfaces + that support sink functions." + ::= { optIfGroups 16 } + +optIfOMSnSourcePreOtnPMGroup OBJECT-GROUP + OBJECTS { + optIfOMSnSrcCurrentSuspectedFlag, + optIfOMSnSrcCurrentOutputPower, + optIfOMSnSrcCurrentLowOutputPower, + optIfOMSnSrcCurrentHighOutputPower, + optIfOMSnSrcCurrentAggregatedInputPower, + optIfOMSnSrcCurrentLowAggregatedInputPower, + optIfOMSnSrcCurrentHighAggregatedInputPower, + optIfOMSnSrcIntervalSuspectedFlag, + optIfOMSnSrcIntervalLastOutputPower, + optIfOMSnSrcIntervalLowOutputPower, + optIfOMSnSrcIntervalHighOutputPower, + optIfOMSnSrcIntervalLastAggregatedInputPower, + optIfOMSnSrcIntervalLowAggregatedInputPower, + optIfOMSnSrcIntervalHighAggregatedInputPower, + optIfOMSnSrcCurDaySuspectedFlag, + optIfOMSnSrcCurDayLowOutputPower, + optIfOMSnSrcCurDayHighOutputPower, + optIfOMSnSrcCurDayLowAggregatedInputPower, + optIfOMSnSrcCurDayHighAggregatedInputPower, + optIfOMSnSrcPrevDaySuspectedFlag, + optIfOMSnSrcPrevDayLastOutputPower, + optIfOMSnSrcPrevDayLowOutputPower, + optIfOMSnSrcPrevDayHighOutputPower, + optIfOMSnSrcPrevDayLastAggregatedInputPower, + optIfOMSnSrcPrevDayLowAggregatedInputPower, + optIfOMSnSrcPrevDayHighAggregatedInputPower + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + objects applicable to OMSn interfaces that + support source functions." + ::= { optIfGroups 17 } + +optIfOMSnSourcePreOtnPMThresholdGroup OBJECT-GROUP + OBJECTS { + optIfOMSnSrcCurrentLowerOutputPowerThreshold, + optIfOMSnSrcCurrentUpperOutputPowerThreshold, + optIfOMSnSrcCurrentLowerInputPowerThreshold, + optIfOMSnSrcCurrentUpperInputPowerThreshold + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + threshold objects applicable to OMSn interfaces that + that support source functions." + ::= { optIfGroups 18 } + +optIfOChGroupCommonGroup OBJECT-GROUP + OBJECTS { + optIfOChGroupDirectionality + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to all OChGroup interfaces." + ::= { optIfGroups 19 } + +optIfOChGroupSinkPreOtnPMGroup OBJECT-GROUP + OBJECTS { + optIfOChGroupSinkCurrentSuspectedFlag, + optIfOChGroupSinkCurrentAggregatedInputPower, + optIfOChGroupSinkCurrentLowAggregatedInputPower, + optIfOChGroupSinkCurrentHighAggregatedInputPower, + optIfOChGroupSinkCurrentOutputPower, + optIfOChGroupSinkCurrentLowOutputPower, + optIfOChGroupSinkCurrentHighOutputPower, + optIfOChGroupSinkIntervalSuspectedFlag, + optIfOChGroupSinkIntervalLastAggregatedInputPower, + optIfOChGroupSinkIntervalLowAggregatedInputPower, + optIfOChGroupSinkIntervalHighAggregatedInputPower, + optIfOChGroupSinkIntervalLastOutputPower, + optIfOChGroupSinkIntervalLowOutputPower, + optIfOChGroupSinkIntervalHighOutputPower, + optIfOChGroupSinkCurDaySuspectedFlag, + optIfOChGroupSinkCurDayLowAggregatedInputPower, + optIfOChGroupSinkCurDayHighAggregatedInputPower, + optIfOChGroupSinkCurDayLowOutputPower, + optIfOChGroupSinkCurDayHighOutputPower, + optIfOChGroupSinkPrevDaySuspectedFlag, + optIfOChGroupSinkPrevDayLastAggregatedInputPower, + optIfOChGroupSinkPrevDayLowAggregatedInputPower, + optIfOChGroupSinkPrevDayHighAggregatedInputPower, + optIfOChGroupSinkPrevDayLastOutputPower, + optIfOChGroupSinkPrevDayLowOutputPower, + optIfOChGroupSinkPrevDayHighOutputPower + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + objects applicable to OChGroup interfaces that + support sink functions." + ::= { optIfGroups 20 } + +optIfOChGroupSinkPreOtnPMThresholdGroup OBJECT-GROUP + OBJECTS { + optIfOChGroupSinkCurrentLowerInputPowerThreshold, + optIfOChGroupSinkCurrentUpperInputPowerThreshold, + optIfOChGroupSinkCurrentLowerOutputPowerThreshold, + optIfOChGroupSinkCurrentUpperOutputPowerThreshold + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + threshold objects applicable to OChGroup interfaces + that support sink functions." + ::= { optIfGroups 21 } + +optIfOChGroupSourcePreOtnPMGroup OBJECT-GROUP + OBJECTS { + optIfOChGroupSrcCurrentSuspectedFlag, + optIfOChGroupSrcCurrentOutputPower, + optIfOChGroupSrcCurrentLowOutputPower, + optIfOChGroupSrcCurrentHighOutputPower, + optIfOChGroupSrcCurrentAggregatedInputPower, + optIfOChGroupSrcCurrentLowAggregatedInputPower, + optIfOChGroupSrcCurrentHighAggregatedInputPower, + optIfOChGroupSrcIntervalSuspectedFlag, + optIfOChGroupSrcIntervalLastOutputPower, + optIfOChGroupSrcIntervalLowOutputPower, + optIfOChGroupSrcIntervalHighOutputPower, + optIfOChGroupSrcIntervalLastAggregatedInputPower, + optIfOChGroupSrcIntervalLowAggregatedInputPower, + optIfOChGroupSrcIntervalHighAggregatedInputPower, + optIfOChGroupSrcCurDaySuspectedFlag, + optIfOChGroupSrcCurDayLowOutputPower, + optIfOChGroupSrcCurDayHighOutputPower, + optIfOChGroupSrcCurDayLowAggregatedInputPower, + optIfOChGroupSrcCurDayHighAggregatedInputPower, + optIfOChGroupSrcPrevDaySuspectedFlag, + optIfOChGroupSrcPrevDayLastOutputPower, + optIfOChGroupSrcPrevDayLowOutputPower, + optIfOChGroupSrcPrevDayHighOutputPower, + optIfOChGroupSrcPrevDayLastAggregatedInputPower, + optIfOChGroupSrcPrevDayLowAggregatedInputPower, + optIfOChGroupSrcPrevDayHighAggregatedInputPower + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + objects applicable to OChGroup interfaces that + support source functions." + ::= { optIfGroups 22 } + +optIfOChGroupSourcePreOtnPMThresholdGroup OBJECT-GROUP + OBJECTS { + optIfOChGroupSrcCurrentLowerOutputPowerThreshold, + optIfOChGroupSrcCurrentUpperOutputPowerThreshold, + optIfOChGroupSrcCurrentLowerInputPowerThreshold, + optIfOChGroupSrcCurrentUpperInputPowerThreshold + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + threshold objects applicable to OChGroup interfaces that + that support source functions." + ::= { optIfGroups 23 } + +optIfOChCommonGroup OBJECT-GROUP + OBJECTS { + optIfOChDirectionality + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to all OCh interfaces." + ::= { optIfGroups 24 } + +optIfOChSinkGroupBasic OBJECT-GROUP + OBJECTS { + optIfOChCurrentStatus + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to all OCh interfaces that + support sink functions." + ::= { optIfGroups 25 } + +optIfOChSinkPreOtnPMGroup OBJECT-GROUP + OBJECTS { + optIfOChSinkCurrentSuspectedFlag, + optIfOChSinkCurrentInputPower, + optIfOChSinkCurrentLowInputPower, + optIfOChSinkCurrentHighInputPower, + optIfOChSinkIntervalSuspectedFlag, + optIfOChSinkIntervalLastInputPower, + optIfOChSinkIntervalLowInputPower, + optIfOChSinkIntervalHighInputPower, + optIfOChSinkCurDaySuspectedFlag, + optIfOChSinkCurDayLowInputPower, + optIfOChSinkCurDayHighInputPower, + optIfOChSinkPrevDaySuspectedFlag, + optIfOChSinkPrevDayLastInputPower, + optIfOChSinkPrevDayLowInputPower, + optIfOChSinkPrevDayHighInputPower + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + objects applicable to OCh interfaces that + support sink functions." + ::= { optIfGroups 26 } + +optIfOChSinkPreOtnPMThresholdGroup OBJECT-GROUP + OBJECTS { + optIfOChSinkCurrentLowerInputPowerThreshold, + optIfOChSinkCurrentUpperInputPowerThreshold + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + threshold objects applicable to OCh interfaces + that support sink functions." + ::= { optIfGroups 27 } + + +optIfOChSourcePreOtnPMGroup OBJECT-GROUP + OBJECTS { + optIfOChSrcCurrentSuspectedFlag, + optIfOChSrcCurrentOutputPower, + optIfOChSrcCurrentLowOutputPower, + optIfOChSrcCurrentHighOutputPower, + optIfOChSrcIntervalSuspectedFlag, + optIfOChSrcIntervalLastOutputPower, + optIfOChSrcIntervalLowOutputPower, + optIfOChSrcIntervalHighOutputPower, + optIfOChSrcCurDaySuspectedFlag, + optIfOChSrcCurDayLowOutputPower, + optIfOChSrcCurDayHighOutputPower, + optIfOChSrcPrevDaySuspectedFlag, + optIfOChSrcPrevDayLastOutputPower, + optIfOChSrcPrevDayLowOutputPower, + optIfOChSrcPrevDayHighOutputPower + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + objects applicable to OCh interfaces that + support source functions." + ::= { optIfGroups 28 } + +optIfOChSourcePreOtnPMThresholdGroup OBJECT-GROUP + OBJECTS { + optIfOChSrcCurrentLowerOutputPowerThreshold, + optIfOChSrcCurrentUpperOutputPowerThreshold + } + STATUS current + DESCRIPTION + "A collection of pre-OTN performance monitoring + threshold objects applicable to OCh interfaces + that support source functions." + ::= { optIfGroups 29 } + +optIfOTUkCommonGroup OBJECT-GROUP + OBJECTS { + optIfOTUkDirectionality, + optIfOTUkBitRateK + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to all OTUk interfaces." + ::= { optIfGroups 30 } + +optIfOTUkSourceGroup OBJECT-GROUP + OBJECTS { + optIfOTUkTraceIdentifierTransmitted, + optIfOTUkSourceAdaptActive + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to OTUk interfaces that + support source functions." + ::= { optIfGroups 31 } + +optIfOTUkSinkGroup OBJECT-GROUP + OBJECTS { + optIfOTUkDAPIExpected, + optIfOTUkSAPIExpected, + optIfOTUkTraceIdentifierAccepted, + optIfOTUkTIMDetMode, + optIfOTUkTIMActEnabled, + optIfOTUkDEGThr, + optIfOTUkDEGM, + optIfOTUkSinkAdaptActive, + optIfOTUkSinkFECEnabled, + optIfOTUkCurrentStatus + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to OTUk interfaces that + support sink functions." + ::= { optIfGroups 32 } + +optIfGCC0Group OBJECT-GROUP + OBJECTS { + optIfGCC0Application, + optIfGCC0RowStatus + } + STATUS current + DESCRIPTION + "A collection of GCC0 configuration objects." + ::= { optIfGroups 33 } + +optIfODUkGroup OBJECT-GROUP + OBJECTS { + optIfODUkDirectionality, + optIfODUkBitRateK, + optIfODUkTcmFieldsInUse, + optIfODUkPositionSeqCurrentSize, + optIfODUkPositionSeqPosition, + optIfODUkPositionSeqPointer, + optIfODUkTtpPresent + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to all ODUk interfaces." + ::= { optIfGroups 34 } + +optIfODUkTtpSourceGroup OBJECT-GROUP + OBJECTS { + optIfODUkTtpTraceIdentifierTransmitted + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to all interfaces that support + ODUk trail termination source functions." + ::= { optIfGroups 35 } + +optIfODUkTtpSinkGroup OBJECT-GROUP + OBJECTS { + optIfODUkTtpDAPIExpected, + optIfODUkTtpSAPIExpected, + optIfODUkTtpTraceIdentifierAccepted, + optIfODUkTtpTIMDetMode, + optIfODUkTtpTIMActEnabled, + optIfODUkTtpDEGThr, + optIfODUkTtpDEGM, + optIfODUkTtpCurrentStatus + } + STATUS current + DESCRIPTION + "A collection of ODUk configuration objects + applicable to all interfaces that support + ODUk trail termination sink functions." + ::= { optIfGroups 36 } + +optIfODUkNimGroup OBJECT-GROUP + OBJECTS { + optIfODUkNimDAPIExpected, + optIfODUkNimSAPIExpected, + optIfODUkNimTraceIdentifierAccepted, + optIfODUkNimTIMDetMode, + optIfODUkNimTIMActEnabled, + optIfODUkNimDEGThr, + optIfODUkNimDEGM, + optIfODUkNimCurrentStatus, + optIfODUkNimRowStatus + } + STATUS current + DESCRIPTION + "A collection of ODUk Nim configuration objects." + ::= { optIfGroups 37 } + +optIfGCC12Group OBJECT-GROUP + OBJECTS { + optIfGCC12GCCPassThrough, + optIfGCC12Application, + optIfGCC12RowStatus + } + STATUS current + DESCRIPTION + "A collection of GCC12 configuration objects." + ::= { optIfGroups 38 } + +optIfODUkTCommonGroup OBJECT-GROUP + OBJECTS { + optIfODUkTRowStatus + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to all ODUkT instances." + ::= { optIfGroups 39 } + +optIfODUkTSourceGroup OBJECT-GROUP + OBJECTS { + optIfODUkTTraceIdentifierTransmitted, + optIfODUkTSourceLockSignalAdminState + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to all ODUkT instances + that provide source functions." + ::= { optIfGroups 40 } + +optIfODUkTSinkGroup OBJECT-GROUP + OBJECTS { + optIfODUkTDAPIExpected, + optIfODUkTSAPIExpected, + optIfODUkTTraceIdentifierAccepted, + optIfODUkTTIMDetMode, + optIfODUkTTIMActEnabled, + optIfODUkTDEGThr, + optIfODUkTDEGM, + optIfODUkTCurrentStatus + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to all ODUkT instances + that provide sink functions." + ::= { optIfGroups 41 } + +optIfODUkTSinkGroupCtp OBJECT-GROUP + OBJECTS { + optIfODUkTSinkMode, + optIfODUkTSinkLockSignalAdminState + } + STATUS current + DESCRIPTION + "A collection of configuration objects + applicable to ODUkT instances not + colocated with an ODUk TTP that + provide sink functions." + ::= { optIfGroups 42 } + +optIfODUkTNimGroup OBJECT-GROUP + OBJECTS { + optIfODUkTNimDAPIExpected, + optIfODUkTNimSAPIExpected, + optIfODUkTNimTraceIdentifierAccepted, + optIfODUkTNimTIMDetMode, + optIfODUkTNimTIMActEnabled, + optIfODUkTNimDEGThr, + optIfODUkTNimDEGM, + optIfODUkTNimCurrentStatus, + optIfODUkTNimRowStatus + } + STATUS current + DESCRIPTION + "A collection of ODUkT Nim configuration objects." + ::= { optIfGroups 43 } + + +END + |