diff options
Diffstat (limited to 'MIBS/junos/JUNIPER-MPLS-LDP-MIB')
| -rw-r--r-- | MIBS/junos/JUNIPER-MPLS-LDP-MIB | 2195 |
1 files changed, 2195 insertions, 0 deletions
diff --git a/MIBS/junos/JUNIPER-MPLS-LDP-MIB b/MIBS/junos/JUNIPER-MPLS-LDP-MIB new file mode 100644 index 0000000..a3e353d --- /dev/null +++ b/MIBS/junos/JUNIPER-MPLS-LDP-MIB @@ -0,0 +1,2195 @@ +JUNIPER-MPLS-LDP-MIB DEFINITIONS ::= BEGIN + +IMPORTS + OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE, + Integer32, Counter32, Unsigned32 + FROM SNMPv2-SMI + MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP + FROM SNMPv2-CONF + + RowPointer, RowStatus, TimeInterval, TruthValue, + TimeStamp, StorageType + FROM SNMPv2-TC + + InterfaceIndex + FROM IF-MIB + + InetAddressType, + InetAddress, + InetPortNumber + FROM INET-ADDRESS-MIB + + jnxMibs + FROM JUNIPER-SMI + + MplsLabel, + MplsLabelDistributionMethod, + MplsLdpIdentifier, + MplsLdpLabelType, + MplsLspType, + MplsLsrIdentifier, + MplsRetentionMode + + FROM MPLS-TC-STD-MIB + ; + + +jnxMplsLdpMIB MODULE-IDENTITY + LAST-UPDATED "200605161200Z" -- 16 May 2006 + ORGANIZATION "Juniper Networks, Inc." + CONTACT-INFO + " Juniper Technical Assistance Center + Juniper Networks, Inc. + 1133 Innovation Way + Sunnyvale, CA 94089 + E-mail: support@juniper.net" + + DESCRIPTION + "This MIB contains managed object definitions for the + 'Multiprotocol Label Switching, Label Distribution + Protocol, LDP' document." + + REVISION "200605161200Z" -- 16 May 2006 + DESCRIPTION + "This mib was earlier supported on JUNOS as + ldpmib.mib (MPLS-LDP-MIB)." + + ::= { jnxMibs 36 } + + +--**************************************************************** + +jnxMplsLdpObjects OBJECT IDENTIFIER ::= { jnxMplsLdpMIB 1 } +jnxMplsLdpNotifications OBJECT IDENTIFIER ::= { jnxMplsLdpMIB 2 } +jnxMplsLdpConformance OBJECT IDENTIFIER ::= { jnxMplsLdpMIB 3 } + +--**************************************************************** +-- MPLS LDP Objects +--**************************************************************** + +jnxMplsLdpLsrObjects OBJECT IDENTIFIER ::= { jnxMplsLdpObjects 1 } + +jnxMplsLdpEntityObjects OBJECT IDENTIFIER ::= { jnxMplsLdpObjects 2 } + +-- +-- The MPLS Label Distribution Protocol's +-- Label Switching Router Objects +-- + +jnxMplsLdpLsrId OBJECT-TYPE + SYNTAX MplsLsrIdentifier + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The LSR's Identifier." + ::= { jnxMplsLdpLsrObjects 1 } + +jnxMplsLdpLsrLoopDetectionCapable OBJECT-TYPE + SYNTAX INTEGER { + none(1), + other(2), + hopCount(3), + pathVector(4), + + hopCountAndPathVector(5) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A indication of whether this + Label Switching Router supports + loop detection. + + none(1) -- Loop Detection is not supported + on this LSR. + + other(2) -- Loop Detection is supported but + by a method other than those + listed below. + + hopCount(3) -- Loop Detection is supported by + Hop Count only. + + pathVector(4) -- Loop Detection is supported by + Path Vector only. + + hopCountAndPathVector(5) -- Loop Detection is + supported by both Hop Count + And Path Vector. + + Since Loop Detection is determined during + Session Initialization, an individual session + may not be running with loop detection. This + object simply gives an indication of whether or not the + LSR has the ability to support Loop Detection and + which types." + ::= { jnxMplsLdpLsrObjects 2 } + + +-- +-- The MPLS Label Distribution Protocol Entity Objects +-- + + +jnxMplsLdpEntityLastChange OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime at the time of the most + recent addition or deletion of an entry + to the jnxMplsLdpEntityTable/jnxMplsLdpEntityStatsTable. + + If no such changes have occurred since the last + + re-initialization of the local management subsystem, + then this object contains a zero value." + ::= { jnxMplsLdpEntityObjects 1 } + +jnxMplsLdpEntityIndexNext OBJECT-TYPE + SYNTAX Unsigned32 (0..4294967295) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object contains an appropriate value to + be used for jnxMplsLdpEntityIndex when creating + entries in the jnxMplsLdpEntityTable. The value + 0 indicates that no unassigned entries are + available. To obtain the jnxMplsLdpEntityIndex + value for a new entry, the manager issues a + management protocol retrieval operation to obtain + the current value of this object. After each + retrieval, the agent should modify the value to + the next unassigned index." + ::= { jnxMplsLdpEntityObjects 2 } + + +jnxMplsLdpEntityTable OBJECT-TYPE + SYNTAX SEQUENCE OF JnxMplsLdpEntityEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table contains information about the + MPLS Label Distribution Protocol Entities which + exist on this Label Switching Router (LSR)." + ::= { jnxMplsLdpEntityObjects 3 } + +jnxMplsLdpEntityEntry OBJECT-TYPE + SYNTAX JnxMplsLdpEntityEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table represents an LDP entity. + An entry can be created by a network administrator + or by an SNMP agent as instructed by LDP." + INDEX { jnxMplsLdpEntityLdpId, jnxMplsLdpEntityIndex } + ::= { jnxMplsLdpEntityTable 1 } + +JnxMplsLdpEntityEntry ::= SEQUENCE { + jnxMplsLdpEntityLdpId MplsLdpIdentifier, + jnxMplsLdpEntityIndex Unsigned32, + jnxMplsLdpEntityProtocolVersion Integer32, + jnxMplsLdpEntityAdminStatus INTEGER, + jnxMplsLdpEntityOperStatus INTEGER, + jnxMplsLdpEntityTcpDscPort InetPortNumber, + + jnxMplsLdpEntityUdpDscPort InetPortNumber, + jnxMplsLdpEntityMaxPduLength Unsigned32, + jnxMplsLdpEntityKeepAliveHoldTimer Integer32, + jnxMplsLdpEntityHelloHoldTimer Integer32, + jnxMplsLdpEntityInitSesThreshold Integer32, + jnxMplsLdpEntityLabelDistMethod MplsLabelDistributionMethod, + jnxMplsLdpEntityLabelRetentionMode MplsRetentionMode, + jnxMplsLdpEntityPathVectorLimit Integer32, + jnxMplsLdpEntityHopCountLimit Integer32, + jnxMplsLdpEntityTargetPeer TruthValue, + jnxMplsLdpEntityTargetPeerAddrType InetAddressType, + jnxMplsLdpEntityTargetPeerAddr InetAddress, + jnxMplsLdpEntityLabelType MplsLdpLabelType, + jnxMplsLdpEntityDiscontinuityTime TimeStamp, + jnxMplsLdpEntityStorageType StorageType, + jnxMplsLdpEntityRowStatus RowStatus +} + + +jnxMplsLdpEntityLdpId OBJECT-TYPE + SYNTAX MplsLdpIdentifier + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The LDP identifier." + REFERENCE + "[RFC3036] LDP Specification, Section on LDP Identifiers." + ::= { jnxMplsLdpEntityEntry 1 } + +jnxMplsLdpEntityIndex OBJECT-TYPE + SYNTAX Unsigned32 (1..4294967295) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This index is used as a secondary index to uniquely + identify this row. Before creating a row in this table, + the 'jnxMplsLdpEntityIndexNext' object should be retrieved. + That value should be used for the value of this index + when creating a row in this table. (NOTE: if a value + of zero (0) is retrieved, that indicates that no rows + can be created in this table at this time. + + A secondary index (this object) is meaningful to some + but not all, LDP implementations. For example + in an LDP implementation which uses PPP would + use this index to differentiate PPP sub-links. + + Another way to use this index is to give this the + value of ifIndex. However, this is dependant + on the implementation." + + ::= { jnxMplsLdpEntityEntry 2 } + +jnxMplsLdpEntityProtocolVersion OBJECT-TYPE + SYNTAX Integer32(1..65535) +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The version number of the LDP protocol which will be + used in the session initialization message. + + Section 3.5.3 in the LDP Specification specifies + that the version of the LDP protocol is negotiated during + session establishment. The value of this object + represents the value that is sent in the initialization + message." + REFERENCE + "[RFC3036], LDP Specification, Section 3.5.3 Initialization + Message." + DEFVAL { 1 } + ::= { jnxMplsLdpEntityEntry 3 } + +jnxMplsLdpEntityAdminStatus OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2) + } +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The administrative status of this LDP Entity. + If this object is changed from 'enable' to 'disable' + and this entity has already attempted to establish + contact with a Peer, then all contact with that + Peer is lost and all information from that Peer + needs to be removed from the MIB. (This implies + that the network management subsystem should clean + up any related entry in the jnxMplsLdpPeerTable). + + At this point the user is able to change values + which are related to this entity. + + When the admin status is set back to 'up', then + this Entity will attempt to establish a new session + with the Peer." + DEFVAL { enable } + ::= { jnxMplsLdpEntityEntry 4 } + + +jnxMplsLdpEntityOperStatus OBJECT-TYPE + SYNTAX INTEGER { + + unknown(1), + enabled(2), + disabled(3) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The operational status of this LDP Entity." + ::= { jnxMplsLdpEntityEntry 5 } + +jnxMplsLdpEntityTcpDscPort OBJECT-TYPE + SYNTAX InetPortNumber +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The TCP Discovery Port for + LDP. The default value is the well-known + value of this port." + REFERENCE + "[RFC3036], LDP Specification, Section 2.4.1, + Basic Discovery Mechanism, Section 2.4.2, + Extended Discovery Mechanism, Section + 3.10, Well-known Numbers, and Section 3.10.1. + UDP and TCP Ports." + DEFVAL { 646 } + ::= { jnxMplsLdpEntityEntry 6 } + +jnxMplsLdpEntityUdpDscPort OBJECT-TYPE + SYNTAX InetPortNumber +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The UDP Discovery Port for + LDP. The default value is the + well-known value for this port." + REFERENCE + "[RFC3036], LDP Specification, Section 2.4.1, + Basic Discovery Mechanism, Section 2.4.2, + Extended Discovery Mechanism, Section + 3.10, Well-known Numbers, and Section 3.10.1. + UDP and TCP Ports." + DEFVAL { 646 } + ::= { jnxMplsLdpEntityEntry 7 } + +jnxMplsLdpEntityMaxPduLength OBJECT-TYPE + SYNTAX Unsigned32 (256..65535) + UNITS "octets" +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + + "The maximum PDU Length that is sent in + the Common Session Parameters of an Initialization + Message. According to the LDP Specification [RFC3036] + a value of 255 or less specifies the + default maximum length of 4096 octets, this is why + the value of this object starts at 256. The operator + should explicitely choose the default value (i.e. 4096), + or some other value. + + The receiving LSR MUST calculate the maximum PDU + length for the session by using the smaller of its and + its peer's proposals for Max PDU Length." + REFERENCE + "[RFC3036], LDP Specification, Section 3.5.3. + Initialization Message." + DEFVAL { 4096 } + ::= { jnxMplsLdpEntityEntry 8 } + +jnxMplsLdpEntityKeepAliveHoldTimer OBJECT-TYPE + SYNTAX Integer32 (1..65535) + UNITS "seconds" +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The 16-bit integer value which is the proposed keep + alive hold timer for this LDP Entity." + DEFVAL { 40 } + ::= { jnxMplsLdpEntityEntry 9 } + +jnxMplsLdpEntityHelloHoldTimer OBJECT-TYPE + SYNTAX Integer32 (0..65535) + UNITS "seconds" +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The 16-bit integer value which is the proposed Hello + hold timer for this LDP Entity. The Hello Hold time + in seconds. + + An LSR maintains a record of Hellos received + from potential peers. This object represents + the Hold Time in the Common Hello Parameters TLV of + the Hello Message. + + A value of 0 is a default value and should be + interpretted in conjunction with the + jnxMplsLdpEntityTargetPeer object. + + If the value of this object is 0: if the value of the + jnxMplsLdpEntityTargetPeer object is false(2), then this + + specifies that the Hold Time's actual default value is + 15 seconds (i.e. the default Hold time for Link Hellos + is 15 seconds). Otherwise if the value of the + jnxMplsLdpEntityTargetPeer object is true(1), then this + specifies that the Hold Time's actual default value is + 45 seconds (i.e. the default Hold time for Targeted + Hellos is 45 seconds). + + A value of 65535 means infinite (i.e. wait forever). + + All other values represent the amount of time in + seconds to wait for a Hello Message. Setting the + hold time to a value smaller than 15 is not + recommended, although not forbidden according + to [RFC3036]." + REFERENCE + "[RFC3036], LDP Specification, Section 3.5.2., + Hello Message." + DEFVAL { 0 } + ::= { jnxMplsLdpEntityEntry 10 } + +jnxMplsLdpEntityInitSesThreshold OBJECT-TYPE + SYNTAX Integer32(0..100) +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "When attempting to establish a session with a + given Peer, the given LDP Entity should + send out the SNMP notification, + 'jnxMplsLdpInitSesThresholdExceeded', when + the number of Session Initialization messages sent + exceeds this threshold. The notification is + used to notify an operator when this Entity and + its Peer are possibily engaged in an endless + sequence of messages as each NAKs the other's + Initialization messages with Error Notification + messages. Setting this threshold which triggers + the notification is one way to + notify the operator. + + A value of 0 (zero) for this object + indicates that the threshold is infinity, thus + the SNMP notification will never be generated." + REFERENCE + "[RFC3036], LDP Specification, + Section 2.5.3 Session Initialization." + DEFVAL { 8 } + ::= { jnxMplsLdpEntityEntry 11 } + + +jnxMplsLdpEntityLabelDistMethod OBJECT-TYPE + SYNTAX MplsLabelDistributionMethod +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "For any given LDP session, the method of + label distribution must be specified." + ::= { jnxMplsLdpEntityEntry 12 } + +jnxMplsLdpEntityLabelRetentionMode OBJECT-TYPE + SYNTAX MplsRetentionMode +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The LDP Entity can be configured to use either + conservative or liberal label retention mode. + + If the value of this object is conservative(1) + then advertized label mappings are retained + only if they will be used to forward packets, + i.e. if label came from a valid next hop. + + If the value of this object is liberal(2) + then all advertized label mappings are retained + whether they are from a valid next hop or not." + ::= { jnxMplsLdpEntityEntry 13 } + +jnxMplsLdpEntityPathVectorLimit OBJECT-TYPE + SYNTAX Integer32 (0..255) +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If the value of this object is 0 (zero) then + Loop Dection for Path Vectors is disabled. + + Otherwise, if this object has a value greater than + zero, then Loop Dection for Path Vectors is enabled, + and the Path Vector Limit is this value. + Also, the value of the object, + 'jnxMplsLdpLsrLoopDetectionCapable', must be set to + either 'pathVector(4)' or 'hopCountAndPathVector(5)', + if this object has a value greater than 0 (zero), + otherwise it is ignored." + REFERENCE + "[RFC3036], LDP Specification, Section 2.8 Loop Dection, + Section 3.4.5 Path Vector TLV." + ::= { jnxMplsLdpEntityEntry 14 } + +jnxMplsLdpEntityHopCountLimit OBJECT-TYPE + SYNTAX Integer32 (0..255) + +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If the value of this object is 0 (zero), + then Loop Detection using Hop Counters is + disabled. + + If the value of this object is greater than + 0 (zero) then Loop Detection using Hop + Counters is enabled, and this object + specifies this Entity's maximum allowable + value for the Hop Count. + Also, the value of the object + jnxMplsLdpLsrLoopDetectionCapable must be set + to either 'hopCount(3)' or + 'hopCountAndPathVector(5)' if this object + has a value greater than 0 (zero), otherwise + it is ignored." + DEFVAL { 0 } + ::= { jnxMplsLdpEntityEntry 15 } + +jnxMplsLdpEntityTargetPeer OBJECT-TYPE + SYNTAX TruthValue +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If this LDP entity uses targeted peer then set + this to true." + DEFVAL { false } + ::= { jnxMplsLdpEntityEntry 16 } + +jnxMplsLdpEntityTargetPeerAddrType OBJECT-TYPE + SYNTAX InetAddressType +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The type of the internetwork layer address used for + the Extended Discovery. This object indicates how + the value of jnxMplsLdpEntityTargetPeerAddr is to + be interpreted." + ::= { jnxMplsLdpEntityEntry 17 } + +jnxMplsLdpEntityTargetPeerAddr OBJECT-TYPE + SYNTAX InetAddress +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of the internetwork layer address used for + the Extended Discovery." + ::= { jnxMplsLdpEntityEntry 18 } + +jnxMplsLdpEntityLabelType OBJECT-TYPE + SYNTAX MplsLdpLabelType +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Specifies the optional parameters for the LDP + Initialization Message. If the value is generic(1) + then no optional parameters will be sent in + the LDP Initialization message associated with + this Entity. + + If the value is atmParameters(2) then + a row must be created in the jnxMplsLdpEntityAtmParms + Table, which corresponds to this entry. + + If the value is frameRelayParameters(3) then + a row must be created in the jnxMplsLdpEntityFrameRelayParms + Table, which corresponds to this entry." + REFERENCE + "[RFC3036], LDP Specification, Section 3.5.3., + Initialization Message." + ::= { jnxMplsLdpEntityEntry 19 } + + +jnxMplsLdpEntityDiscontinuityTime OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime on the most recent occasion + at which any one or more of this entity's counters + suffered a discontinuity. The relevant counters are the + specific instances associated with this entity of + any Counter32, or Counter64 object contained + in the 'jnxMplsLdpEntityStatsTable'. If no such + discontinuities have occurred since the last + re-initialization of the local management + subsystem, then this object contains a zero + value." + ::= { jnxMplsLdpEntityEntry 20 } + +jnxMplsLdpEntityStorageType OBJECT-TYPE + SYNTAX StorageType +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The storage type for this entry." + ::= { jnxMplsLdpEntityEntry 21 } + +jnxMplsLdpEntityRowStatus OBJECT-TYPE + + SYNTAX RowStatus +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "An object that allows entries in this table to + be created and deleted using the + RowStatus convention." + ::= { jnxMplsLdpEntityEntry 22 } + + +-- +-- The MPLS LDP Entity Statistics Table +-- + +jnxMplsLdpEntityStatsTable OBJECT-TYPE + SYNTAX SEQUENCE OF JnxMplsLdpEntityStatsEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table is a read-only table which augments + the jnxMplsLdpEntityTable. The purpose of this + table is to keep statistical information about + the LDP Entities on the LSR." + ::= { jnxMplsLdpEntityObjects 4 } + +jnxMplsLdpEntityStatsEntry OBJECT-TYPE + SYNTAX JnxMplsLdpEntityStatsEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A row in this table contains statistical information + about an LDP Entity. Some counters contained in a + row are for fatal errors received during a former + LDP Session associated with this entry. For example, + an Ldp Pdu received on a TCP connection during an + LDP Session contains a fatal error. That + error is counted here, because the + session is terminated. + + If the error is NOT fatal (i.e. and the Session + remains), then the error is counted in the + jnxMplsLdpSesStatsEntry." + AUGMENTS { jnxMplsLdpEntityEntry } + ::= { jnxMplsLdpEntityStatsTable 1 } + +JnxMplsLdpEntityStatsEntry ::= SEQUENCE { + jnxMplsLdpAttemptedSessions Counter32, + jnxMplsLdpSesRejectedNoHelloErrors Counter32, + jnxMplsLdpSesRejectedAdErrors Counter32, + jnxMplsLdpSesRejectedMaxPduErrors Counter32, + + jnxMplsLdpSesRejectedLRErrors Counter32, + jnxMplsLdpBadLdpIdentifierErrors Counter32, + jnxMplsLdpBadPduLengthErrors Counter32, + jnxMplsLdpBadMessageLengthErrors Counter32, + jnxMplsLdpBadTlvLengthErrors Counter32, + jnxMplsLdpMalformedTlvValueErrors Counter32, + jnxMplsLdpKeepAliveTimerExpErrors Counter32, + jnxMplsLdpShutdownNotifReceived Counter32, + jnxMplsLdpShutdownNotifSent Counter32 +} + +jnxMplsLdpAttemptedSessions OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A count of the total attempted sessions for + this LDP Entity. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of + jnxMplsLdpEntityDiscontinuityTime." + ::= { jnxMplsLdpEntityStatsEntry 1 } + + +jnxMplsLdpSesRejectedNoHelloErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A count of the Session Rejected/No Hello Error + Notification Messages sent or received by + this LDP Entity. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of + jnxMplsLdpEntityDiscontinuityTime." + ::= { jnxMplsLdpEntityStatsEntry 2 } + +jnxMplsLdpSesRejectedAdErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A count of the Session Rejected/Parameters + Advertisement Mode Error Notification Messages sent + or received by this LDP Entity. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of + jnxMplsLdpEntityDiscontinuityTime." + ::= { jnxMplsLdpEntityStatsEntry 3 } + +jnxMplsLdpSesRejectedMaxPduErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A count of the Session Rejected/Parameters + Max Pdu Length Error Notification Messages sent + or received by this LDP Entity. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of + jnxMplsLdpEntityDiscontinuityTime." + ::= { jnxMplsLdpEntityStatsEntry 4 } + +jnxMplsLdpSesRejectedLRErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A count of the Session Rejected/Parameters + Label Range Notification Messages sent + or received by this LDP Entity. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of + jnxMplsLdpEntityDiscontinuityTime." + ::= { jnxMplsLdpEntityStatsEntry 5 } + + +jnxMplsLdpBadLdpIdentifierErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object counts the number of Bad LDP Identifier + Fatal Errors detected by the session(s) + (past and present) associated with this LDP Entity. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of + jnxMplsLdpEntityDiscontinuityTime." + + REFERENCE + "[RFC3036], LDP Specification, Section 3.5.1.2." + ::= { jnxMplsLdpEntityStatsEntry 6 } + +jnxMplsLdpBadPduLengthErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object counts the number of Bad Pdu Length + Fatal Errors detected by the session(s) + (past and present) associated with this LDP Entity. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of + jnxMplsLdpEntityDiscontinuityTime." + REFERENCE + "[RFC3036], LDP Specification, Section 3.5.1.2." + ::= { jnxMplsLdpEntityStatsEntry 7 } + +jnxMplsLdpBadMessageLengthErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object counts the number of Bad Message + Length Fatal Errors detected by the session(s) + (past and present) associated with this LDP Entity. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of + jnxMplsLdpEntityDiscontinuityTime." + REFERENCE + "[RFC3036], LDP Specification, Section 3.5.1.2." + ::= { jnxMplsLdpEntityStatsEntry 8 } + +jnxMplsLdpBadTlvLengthErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object counts the number of Bad TLV + Length Fatal Errors detected by the session(s) + (past and present) associated with this LDP Entity. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of + + jnxMplsLdpEntityDiscontinuityTime." + REFERENCE + "[RFC3036], LDP Specification, Section 3.5.1.2." + ::= { jnxMplsLdpEntityStatsEntry 9 } + +jnxMplsLdpMalformedTlvValueErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object counts the number of Malformed TLV + Value Fatal Errors detected by the session(s) + (past and present) associated with this + LDP Entity. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of + jnxMplsLdpEntityDiscontinuityTime." + REFERENCE + "[RFC3036], LDP Specification, Section 3.5.1.2." + ::= { jnxMplsLdpEntityStatsEntry 10 } + +jnxMplsLdpKeepAliveTimerExpErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object counts the number of Session Keep Alive + Timer Expired Errors detected by the session(s) + (past and present) associated with this LDP Entity. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of + jnxMplsLdpEntityDiscontinuityTime." + REFERENCE + "[RFC3036], LDP Specification, Section 3.5.1.2." + ::= { jnxMplsLdpEntityStatsEntry 11 } + +jnxMplsLdpShutdownNotifReceived OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object counts the number of Shutdown Notfications + received related to session(s) (past and present) + associated with this LDP Entity. + + Discontinuities in the value of this counter can occur + + at re-initialization of the management system, and at + other times as indicated by the value of + jnxMplsLdpEntityDiscontinuityTime." + ::= { jnxMplsLdpEntityStatsEntry 12 } + +jnxMplsLdpShutdownNotifSent OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object counts the number of Shutdown Notfications + sent related to session(s) (past and present) associated + with this LDP Entity. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of + jnxMplsLdpEntityDiscontinuityTime." + ::= { jnxMplsLdpEntityStatsEntry 13 } + + +-- +-- The MPLS LDP Peer Table +-- + +jnxMplsLdpSessionObjects OBJECT IDENTIFIER ::= + { jnxMplsLdpObjects 3 } + + +jnxMplsLdpPeerLastChange OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime at the time of the most + recent addition or deletion to the + jnxMplsLdpPeerTable/jnxMplsLdpSessionTable." + ::= { jnxMplsLdpSessionObjects 1 } + +jnxMplsLdpPeerTable OBJECT-TYPE + SYNTAX SEQUENCE OF JnxMplsLdpPeerEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information about LDP peers known by Entities in + the jnxMplsLdpEntityTable. The information in this table + is based on information from the Entity-Peer interaction + during session initialization but is not appropriate + for the jnxMplsLdpSessionTable, because objects in this + table may or may not be used in session establishment." + + ::= { jnxMplsLdpSessionObjects 2 } + +jnxMplsLdpPeerEntry OBJECT-TYPE + SYNTAX JnxMplsLdpPeerEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information about a single Peer which is related + to a Session. NOTE: this table is augmented by + the jnxMplsLdpSessionTable." + INDEX { jnxMplsLdpEntityLdpId, + jnxMplsLdpEntityIndex, + jnxMplsLdpPeerLdpId } + ::= { jnxMplsLdpPeerTable 1 } + +JnxMplsLdpPeerEntry ::= SEQUENCE { + jnxMplsLdpPeerLdpId MplsLdpIdentifier, + jnxMplsLdpPeerLabelDistMethod MplsLabelDistributionMethod, + jnxMplsLdpPeerPathVectorLimit Integer32 +} + +jnxMplsLdpPeerLdpId OBJECT-TYPE + SYNTAX MplsLdpIdentifier + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The LDP identifier of this LDP Peer." + ::= { jnxMplsLdpPeerEntry 1 } + +jnxMplsLdpPeerLabelDistMethod OBJECT-TYPE + SYNTAX MplsLabelDistributionMethod + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "For any given LDP session, the method of + label distribution must be specified." + ::= { jnxMplsLdpPeerEntry 2 } + +jnxMplsLdpPeerPathVectorLimit OBJECT-TYPE + SYNTAX Integer32 (0..255) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If the value of this object is 0 (zero) then + Loop Dection for Path Vectors for this Peer + is disabled. + + Otherwise, if this object has a value greater than + zero, then Loop Dection for Path Vectors for this + Peer is enabled and the Path Vector Limit is this value." + + REFERENCE + "[RFC3036], LDP Specification, Section 2.8 Loop Dection, + Section 3.4.5 Path Vector TLV." + ::= { jnxMplsLdpPeerEntry 3 } + + +-- +-- The MPLS LDP Sessions Table +-- + +jnxMplsLdpSessionTable OBJECT-TYPE + SYNTAX SEQUENCE OF JnxMplsLdpSessionEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of Sessions between the LDP Entities and + LDP Peers. Each row represents a single session." + ::= { jnxMplsLdpSessionObjects 3 } + +jnxMplsLdpSessionEntry OBJECT-TYPE + SYNTAX JnxMplsLdpSessionEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table represents information on a + single session between an LDP Entity and LDP Peer. + The information contained in a row is read-only. + + Please note: the Path Vector Limit for the + Session is the value which is configured in + the corresponding jnxMplsLdpEntityEntry. The + Peer's Path Vector Limit is in noted in the + jnxMplsLdpPeerTable. + + Values which may differ from those configured are + noted in the objects of this table, the + jnxMplsLdpAtmSesTable and the + jnxMplsLdpFrameRelaySesTable. A value will + differ if it was negotiated between the + Entity and the Peer. Values may or may not + be negotiated. For example, if the values + are the same then no negotiation takes place. + If they are negotiated, then they may differ." + AUGMENTS { jnxMplsLdpPeerEntry } + ::= { jnxMplsLdpSessionTable 1 } + +JnxMplsLdpSessionEntry ::= SEQUENCE { + jnxMplsLdpSesStateLastChange TimeStamp, + jnxMplsLdpSesState INTEGER, + jnxMplsLdpSesProtocolVersion Integer32, + + jnxMplsLdpSesKeepAliveHoldTimeRem TimeInterval, + jnxMplsLdpSesMaxPduLength Unsigned32, + jnxMplsLdpSesDiscontinuityTime TimeStamp +} + +jnxMplsLdpSesStateLastChange OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of this object is sysUpTime when the + most recent change in the jnxMplsLdpSesState + object occurred. When the entry is created, then + this object has the value of sysUpTime when the + entry was created." + ::= { jnxMplsLdpSessionEntry 1 } + +jnxMplsLdpSesState OBJECT-TYPE + SYNTAX INTEGER { + nonexistent(1), + initialized(2), + openrec(3), + opensent(4), + operational(5) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The current state of the session, all of the + states 1 to 5 are based on the state machine for + session negotiation behavior." + REFERENCE + "[RFC3036], LDP Specification, Section 2.5.4, + Initialization State Machine." + ::= { jnxMplsLdpSessionEntry 2 } + +jnxMplsLdpSesProtocolVersion OBJECT-TYPE + SYNTAX Integer32(1..65535) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The version of the LDP Protocol which + this session is using. This is the version of + the LDP protocol which has been negotiated during + session initialization." + REFERENCE + "[RFC3036], LDP Specification, Section 3.5.3, + Initialization Message." + ::= { jnxMplsLdpSessionEntry 3 } + +jnxMplsLdpSesKeepAliveHoldTimeRem OBJECT-TYPE + SYNTAX TimeInterval + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The keep alive hold time remaining for this session." + ::= { jnxMplsLdpSessionEntry 4 } + +jnxMplsLdpSesMaxPduLength OBJECT-TYPE + SYNTAX Unsigned32 (1..65535) + UNITS "octets" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of maximum allowable length for LDP PDUs for + this session. This value may have been negotiated during + the Session Initialization. This object is related to + the jnxMplsLdpEntityMaxPduLength object. The + jnxMplsLdpEntityMaxPduLength object specifies the requested + LDP PDU length, and this object reflects the negotiated + LDP PDU length between the Entity and + the Peer." + ::= { jnxMplsLdpSessionEntry 5 } + +jnxMplsLdpSesDiscontinuityTime OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime on the most recent occasion at + which any one or more of this session's counters + suffered a discontinuity. The relevant counters are + the specific instances associated with this session + of any Counter32 or Counter64 object contained in the + jnxMplsLdpSessionStatsTable. + + The initial value of this object is the value of + sysUpTime when the entry was created in this table. + + Also, a command generator can distinguish when a session + between a given Entity and Peer goes away and then is + 're-established'. This value would change and + thus indicate to the command generator that this is a + different session." + ::= { jnxMplsLdpSessionEntry 6 } + + +-- +-- The MPLS LDP Session Statistics Table +-- + +jnxMplsLdpSesStatsTable OBJECT-TYPE + SYNTAX SEQUENCE OF JnxMplsLdpSesStatsEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of statistics for Sessions between + LDP Entities and LDP Peers." + ::= { jnxMplsLdpSessionObjects 4 } + +jnxMplsLdpSesStatsEntry OBJECT-TYPE + SYNTAX JnxMplsLdpSesStatsEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table represents statistical + information on a single session between an LDP + Entity and LDP Peer." + AUGMENTS { jnxMplsLdpPeerEntry } + ::= { jnxMplsLdpSesStatsTable 1 } + +JnxMplsLdpSesStatsEntry ::= SEQUENCE { + jnxMplsLdpSesStatsUnkMesTypeErrors Counter32, + jnxMplsLdpSesStatsUnkTlvErrors Counter32 +} + +jnxMplsLdpSesStatsUnkMesTypeErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object counts the number of Unknown Message Type + Errors detected during this session. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of + jnxMplsLdpSesDiscontinuityTime." + ::= { jnxMplsLdpSesStatsEntry 1 } + +jnxMplsLdpSesStatsUnkTlvErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object counts the number of Unknown TLV Errors + detected during this session. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of + + jnxMplsLdpSessionDiscontinuityTime." + ::= { jnxMplsLdpSesStatsEntry 2 } + + +-- +-- The MPLS LDP Hello Adjacency Table +-- + +jnxMplsLdpHelloAdjacencyObjects OBJECT IDENTIFIER ::= + { jnxMplsLdpSessionObjects 5 } + +jnxMplsLdpHelloAdjacencyTable OBJECT-TYPE + SYNTAX SEQUENCE OF JnxMplsLdpHelloAdjacencyEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of Hello Adjacencies for Sessions." + ::= { jnxMplsLdpHelloAdjacencyObjects 1 } + +jnxMplsLdpHelloAdjacencyEntry OBJECT-TYPE + SYNTAX JnxMplsLdpHelloAdjacencyEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Each row represents a single LDP Hello Adjacency. + An LDP Session can have one or more Hello adjacencies." + INDEX { jnxMplsLdpEntityLdpId, + jnxMplsLdpEntityIndex, + jnxMplsLdpPeerLdpId, + jnxMplsLdpHelloAdjIndex } + ::= { jnxMplsLdpHelloAdjacencyTable 1 } + +JnxMplsLdpHelloAdjacencyEntry ::= SEQUENCE { + jnxMplsLdpHelloAdjIndex Unsigned32, + jnxMplsLdpHelloAdjHoldTimeRem TimeInterval, + jnxMplsLdpHelloAdjType INTEGER +} + +jnxMplsLdpHelloAdjIndex OBJECT-TYPE + SYNTAX Unsigned32 (1..4294967295) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An identifier for this specific adjacency." + ::= { jnxMplsLdpHelloAdjacencyEntry 1 } + +jnxMplsLdpHelloAdjHoldTimeRem OBJECT-TYPE + SYNTAX TimeInterval + MAX-ACCESS read-only + STATUS current + + DESCRIPTION + "The time remaining for this Hello Adjacency. + This interval will change when the 'next' + Hello message which corresponds to this + Hello Adjacency is received." + ::= { jnxMplsLdpHelloAdjacencyEntry 2 } + +jnxMplsLdpHelloAdjType OBJECT-TYPE + SYNTAX INTEGER { + link(1), + targeted(2) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This adjacency is the result of a 'link' + hello if the value of this object is link(1). + Otherwise, it is a result of a 'targeted' + hello, targeted(2)." + ::= { jnxMplsLdpHelloAdjacencyEntry 3 } + + +-- +-- Session Label (LSP) Mapping to LSR MIB's LIB Information. +-- + +jnxMplsLdpLspTable OBJECT-TYPE + SYNTAX SEQUENCE OF JnxMplsLdpLspEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table of LDP LSP's which + map to a Segment Table in the + the LSR MIB's (either the mplsInSegmentTable + or mplsOutSegmentTable) AND to the + LSR MIB's mplsXCTable." + ::= { jnxMplsLdpSessionObjects 6 } + +jnxMplsLdpLspEntry OBJECT-TYPE + SYNTAX JnxMplsLdpLspEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table represents information on a + single LDP LSP which is represented by + a session's index triple (jnxMplsLdpEntityLdpId, + jnxMplsLdpEntityIndex, jnxMplsLdpPeerLdpId) AND the + index tuple (jnxMplsLdpLspIfIndex, jnxMplsLdpLspLabel). + + The information contained in a row is read-only." + + INDEX { jnxMplsLdpEntityLdpId, + jnxMplsLdpEntityIndex, + jnxMplsLdpPeerLdpId, + jnxMplsLdpLspIfIndex, + jnxMplsLdpLspLabel + } + ::= { jnxMplsLdpLspTable 1 } + +JnxMplsLdpLspEntry ::= SEQUENCE { + jnxMplsLdpLspIfIndex InterfaceIndex, + jnxMplsLdpLspLabel MplsLabel, + jnxMplsLdpLspLabelType MplsLdpLabelType, + jnxMplsLdpLspType MplsLspType, + jnxMplsLdpLspLsrInSegmentPointer RowPointer, + jnxMplsLdpLspLsrOutSegmentPointer RowPointer, + jnxMplsLdpLspLsrXCPointer RowPointer +} + +jnxMplsLdpLspIfIndex OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The ifIndex value associated with this LSP." + ::= { jnxMplsLdpLspEntry 1 } + +jnxMplsLdpLspLabel OBJECT-TYPE + SYNTAX MplsLabel + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The LDP label for this LSP." + ::= { jnxMplsLdpLspEntry 2 } + +jnxMplsLdpLspLabelType OBJECT-TYPE + SYNTAX MplsLdpLabelType + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The Layer 2 Label Type." + ::= { jnxMplsLdpLspEntry 3 } + +jnxMplsLdpLspType OBJECT-TYPE + SYNTAX MplsLspType + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The type of LSP connection. + The possible values are: + + unknown(1) -- if the LSP is not known + to be one of the following. + + terminatingLsp(2) -- if the LSP terminates + on the LSR, then this + is an ingressing LSP + which ends on the LSR, + + originatingLsp(3) -- if the LSP originates + from the LSR, then this + is an egressing LSP which is + the head-end of the LSP, + + crossConnectingLsp(4) -- if the LSP ingresses + and egresses on the LSR, + then it is cross-connecting + on that LSR." + ::= { jnxMplsLdpLspEntry 4 } + +jnxMplsLdpLspLsrInSegmentPointer OBJECT-TYPE + SYNTAX RowPointer + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If this LSP terminates or is cross-connecting + on this LSR, then this RowPointer should point + to an instance of an object in the + mplsLsrInSegmentTable. In other words if + the value of jnxMplsLdpLspType is + terminatingLsp(2) or crossConnectingLsp(4), + then this should point to an instance of an object + in the LSR-MIB's mplsInSegmentTable. + + Otherwise, a value of zeroDotzero indicates that + this LSP has no corresponding mplsInSegmentEntry." + ::= { jnxMplsLdpLspEntry 5 } + +jnxMplsLdpLspLsrOutSegmentPointer OBJECT-TYPE + SYNTAX RowPointer + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If this LSP originates or is cross-connecting + on this LSR, then this RowPointer should point + to an instance of an object in the LSR-MIB's + mplsOutSegmentTable. In other words if + the value of jnxMplsLdpLspType is + originatingLsp(3) or crossConnectingLsp(4), + then this should point to an instance of an object + in the LSR-MIB's mplsOutSegmentTable. + + Otherwise, a value of zeroDotzero indicates that + this LSP has no corresponding mplsOutSegmentEntry." + ::= { jnxMplsLdpLspEntry 6 } + +jnxMplsLdpLspLsrXCPointer OBJECT-TYPE + SYNTAX RowPointer + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If this LSP is cross-connecting on this LSR, + then this RowPointer should point + to an instance of an object in the + LSR-MIB's mplsXCTable. In other words if + the value of jnxMplsLdpLspType is crossConnectingLsp(4), + then this should point to an instance of an object + in the LSR-MIB's mplsXCTable. + + Otherwise, a value of zeroDotzero indicates that + this LSP has no corresponding mplsXCEntry." + ::= { jnxMplsLdpLspEntry 7 } + + +-- +-- Mpls FEC Table +-- + +jnxMplsFecObjects OBJECT IDENTIFIER ::= + { jnxMplsLdpSessionObjects 7 } + +jnxMplsFecIndexNext OBJECT-TYPE + SYNTAX Unsigned32 (0..4294967295) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object contains an appropriate value to + be used for jnxMplsFecIndex when creating + entries in the jnxMplsFecTable. The value + 0 indicates that no unassigned entries are + available. To obtain the jnxMplsFecIndex + value for a new entry, the manager issues a + management protocol retrieval operation to obtain + the current value of this object. After each + retrieval, the agent should modify the value to + the next unassigned index." + ::= { jnxMplsFecObjects 1 } + + +jnxMplsFecTable OBJECT-TYPE + SYNTAX SEQUENCE OF JnxMplsFecEntry + MAX-ACCESS not-accessible + + STATUS current + DESCRIPTION + "This table represents the FEC + (Forwarding Equivalence Class) + Information associated with an LSP." + ::= { jnxMplsFecObjects 2 } + +jnxMplsFecEntry OBJECT-TYPE + SYNTAX JnxMplsFecEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Each row represents a single FEC Element." + INDEX { jnxMplsFecIndex } + ::= { jnxMplsFecTable 1 } + +JnxMplsFecEntry ::= SEQUENCE { + jnxMplsFecIndex Unsigned32, + jnxMplsFecType INTEGER, + jnxMplsFecAddrLength Integer32, + jnxMplsFecAddrFamily InetAddressType, + jnxMplsFecAddr InetAddress, + jnxMplsFecStorageType StorageType, + jnxMplsFecRowStatus RowStatus +} + +jnxMplsFecIndex OBJECT-TYPE + SYNTAX Unsigned32(1..4294967295) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The index which uniquely identifies this entry." + ::= { jnxMplsFecEntry 1 } + +jnxMplsFecType OBJECT-TYPE + SYNTAX INTEGER { + prefix(1), + hostAddress(2) + } +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The type of the FEC. If the value of this object + is 'prefix(1)' then the FEC type described by this + row is for address prefixes. + + If the value of this object is 'hostAddress(2)' then + the FEC type described by this row is a host address." + ::= { jnxMplsFecEntry 2 } + +jnxMplsFecAddrLength OBJECT-TYPE + SYNTAX Integer32(0..255) +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If the value of 'jnxMplsFecType' is 'prefix(1)' + then the value of this object is the length in + bits of the address prefix represented by + 'jnxMplsFecAddr', or if the length is zero then + this is a special value which indicates that the + prefix matches all addresses. In this case the + prefix is also zero (i.e. 'jnxMplsFecAddr' will + have the value of zero.)" + DEFVAL { 0 } + ::= { jnxMplsFecEntry 3 } + +jnxMplsFecAddrFamily OBJECT-TYPE + SYNTAX InetAddressType +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of this object is from the Address Family + Numbers." + ::= { jnxMplsFecEntry 4 } + + +jnxMplsFecAddr OBJECT-TYPE + SYNTAX InetAddress +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If the value of 'jnxMplsFecType' is 'prefix(1)' + then the value of this object is the address prefix. + If the value of the 'jnxMplsFecAddrLength' + is object is zero, then this object should also be + zero. + + If the value of the 'jnxMplsFecType' is 'hostAddress(2)' + then this is the host address." + ::= { jnxMplsFecEntry 5 } + +jnxMplsFecStorageType OBJECT-TYPE + SYNTAX StorageType +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The storage type for this entry." + ::= { jnxMplsFecEntry 6 } + +jnxMplsFecRowStatus OBJECT-TYPE + + SYNTAX RowStatus +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "An object that allows entries in this table to + be created and deleted using the + RowStatus convention." + ::= { jnxMplsFecEntry 7 } + + +-- +-- LDP LSP FEC Table +-- + +jnxMplsLdpLspFecTable OBJECT-TYPE + SYNTAX SEQUENCE OF JnxMplsLdpLspFecEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table which shows the relationship between + LDP LSP's and FECs. Each row represents + a single LSP to FEC association. + This table is read-only." + ::= { jnxMplsLdpSessionObjects 8 } + +jnxMplsLdpLspFecEntry OBJECT-TYPE + SYNTAX JnxMplsLdpLspFecEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry represents a LDP LSP + to FEC association." + INDEX { jnxMplsLdpEntityLdpId, + jnxMplsLdpEntityIndex, + jnxMplsLdpPeerLdpId, + jnxMplsLdpLspIfIndex, + jnxMplsLdpLspLabel, + jnxMplsFecIndex + } + ::= { jnxMplsLdpLspFecTable 1 } + +JnxMplsLdpLspFecEntry ::= SEQUENCE { + jnxMplsLdpLspFecOperStatus INTEGER, + jnxMplsLdpLspFecLastChange TimeStamp, + jnxMplsLdpLspFecRowStatus RowStatus +} + +jnxMplsLdpLspFecOperStatus OBJECT-TYPE + SYNTAX INTEGER { + unknown(1), + + inUse(2), + notInUse(3) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "An indication of the operational status of + the FEC associated with LDP LSP. + + unknown(1) - this is a temporary state which + may indicate the LSP-FEC association + is in a state of transition. + + inUse(2) - the FEC associated with the LSP is + currently being applied. + + notInUse(3) - the FEC associated with the LSP is + not being applied. Eventually, this + entry may be aged out." + ::= { jnxMplsLdpLspFecEntry 1 } + +jnxMplsLdpLspFecLastChange OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This value of sysUpTime when the + jnxMplsLdpLspFecOperStatus last changed state." + ::= { jnxMplsLdpLspFecEntry 2 } + +jnxMplsLdpLspFecRowStatus OBJECT-TYPE + SYNTAX RowStatus +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "An object that allows entries in this table to + be created and deleted using the + RowStatus convention." + ::= { jnxMplsLdpLspFecEntry 3 } + + +-- +-- Address Message/Address Withdraw Message Information +-- +-- This information is associated with a specific Session +-- because Label Address Messages are sent after session +-- initialization has taken place. +-- + +jnxMplsLdpSesPeerAddrTable OBJECT-TYPE + + SYNTAX SEQUENCE OF JnxMplsLdpSesPeerAddrEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table 'extends' the jnxMplsLdpSessionTable. + This table is used to store Label Address Information + from Label Address Messages received by this LSR from + Peers. This table is read-only and should be updated + when Label Withdraw Address Messages are received, i.e. + Rows should be deleted as apropriate. + + NOTE: since more than one address may be contained + in a Label Address Message, this table 'extends', + rather than 'AUGMENTS' the jnxMplsLdpSessionTable's + information." + ::= { jnxMplsLdpSessionObjects 9 } + +jnxMplsLdpSesPeerAddrEntry OBJECT-TYPE + SYNTAX JnxMplsLdpSesPeerAddrEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table represents information on + session's for a single next hop address which was + advertised in an Address Message from the LDP peer. + The information contained in a row is read-only." + INDEX { jnxMplsLdpEntityLdpId, + jnxMplsLdpEntityIndex, + jnxMplsLdpPeerLdpId, + jnxMplsLdpSesPeerAddrIndex + } + ::= { jnxMplsLdpSesPeerAddrTable 1 } + +JnxMplsLdpSesPeerAddrEntry ::= SEQUENCE { + jnxMplsLdpSesPeerAddrIndex Unsigned32, + jnxMplsLdpSesPeerNextHopAddrType InetAddressType, + jnxMplsLdpSesPeerNextHopAddr InetAddress +} + +jnxMplsLdpSesPeerAddrIndex OBJECT-TYPE + SYNTAX Unsigned32 (1..4294967295) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An index which uniquely identifies this entry within + a given session." + ::= { jnxMplsLdpSesPeerAddrEntry 1 } + +jnxMplsLdpSesPeerNextHopAddrType OBJECT-TYPE + SYNTAX InetAddressType + + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The internetwork layer address type of this Next Hop + Address as specified in the Label Address Message + associated with this Session. The value of this + object indicates how to interpret the value of + jnxMplsLdpSessionPeerNextHopAddress." + ::= { jnxMplsLdpSesPeerAddrEntry 2 } + +jnxMplsLdpSesPeerNextHopAddr OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of the next hop address." + REFERENCE + "[RFC3036], LDP Specification defines only IPv4 for + LDP Protocol Version 1, see section 3.4.3." + ::= { jnxMplsLdpSesPeerAddrEntry 3 } + + +--- +--- Notifications +--- + +jnxMplsLdpNotificationPrefix OBJECT IDENTIFIER ::= + { jnxMplsLdpNotifications 0 } + +jnxMplsLdpInitSesThresholdExceeded NOTIFICATION-TYPE + OBJECTS { + jnxMplsLdpEntityInitSesThreshold + } + STATUS current + DESCRIPTION + "This notification is generated when the value of + the 'jnxMplsLdpEntityInitSesThreshold' object + is not zero, and the number of Session + Initialization messages exceeds the value + of the 'jnxMplsLdpEntityInitSesThreshold' object." + ::= { jnxMplsLdpNotificationPrefix 1 } + +jnxMplsLdpPathVectorLimitMismatch NOTIFICATION-TYPE + OBJECTS { + jnxMplsLdpEntityPathVectorLimit, + jnxMplsLdpPeerPathVectorLimit + } + STATUS current + DESCRIPTION + "If this notification is enabled to generated, + + then this notification is sent when the + 'jnxMplsLdpEntityPathVectorLimit' does NOT match + the value of the 'jnxMplsLdpPeerPathVectorLimit' for + a specific Entity." + REFERENCE + "[RFC3036], LDP Specification, Section 3.5.3." + ::= { jnxMplsLdpNotificationPrefix 2 } + +jnxMplsLdpSessionUp NOTIFICATION-TYPE + OBJECTS { + jnxMplsLdpSesState, + jnxMplsLdpSesDiscontinuityTime, + jnxMplsLdpSesStatsUnkMesTypeErrors, + jnxMplsLdpSesStatsUnkTlvErrors + } + STATUS current + DESCRIPTION + "If this notification is enabled to generated, + then this notification is sent when the + value of 'jnxMplsLdpSesState' enters + the 'operational(5)' state." + ::= { jnxMplsLdpNotificationPrefix 3 } + +jnxMplsLdpSessionDown NOTIFICATION-TYPE + OBJECTS { + jnxMplsLdpSesState, + jnxMplsLdpSesDiscontinuityTime, + jnxMplsLdpSesStatsUnkMesTypeErrors, + jnxMplsLdpSesStatsUnkTlvErrors + + } + STATUS current + DESCRIPTION + "If this notification is enabled to generated, + then this notification is sent when the + the value of 'jnxMplsLdpSesState' leaves + the 'operational(5)' state." + ::= { jnxMplsLdpNotificationPrefix 4 } + + +--**************************************************************** +-- Module Conformance Statement +--**************************************************************** + + +jnxMplsLdpGroups + OBJECT IDENTIFIER ::= { jnxMplsLdpConformance 1 } + +jnxMplsLdpCompliances + OBJECT IDENTIFIER ::= { jnxMplsLdpConformance 2 } + +-- +-- Full Compliance +-- + +jnxMplsLdpModuleFullCompliance MODULE-COMPLIANCE + STATUS current + DESCRIPTION + "The Module is implemented with support + for read-create and read-write. In other + words, both monitoring and configuration + are available when using this MODULE-COMPLIANCE." + + MODULE -- this module + MANDATORY-GROUPS { jnxMplsLdpGeneralGroup, + jnxMplsLdpLspGroup, + jnxMplsLdpNotificationsGroup + } + + + GROUP jnxMplsLdpLsrGroup + DESCRIPTION + "This group must be supported if the LSR MIB is + implemented, specifically the mplsInSegmentTable, + the mplsOutSegmentTable or the mplsXCTable." + + OBJECT jnxMplsLdpEntityTargetPeerAddrType + SYNTAX InetAddressType + DESCRIPTION + "An implementation is only required to support + 'unknown(0)', and IPv4 addresses. Supporting + IPv6 addresses is optional." + + + OBJECT jnxMplsLdpEntityTargetPeerAddr + SYNTAX InetAddress (SIZE(0|4|16)) + DESCRIPTION + "An implementation is only required to support IPv4 and + may optionally support IPv6 addresses." + + OBJECT jnxMplsLdpEntityRowStatus + SYNTAX INTEGER { active(1) } + WRITE-SYNTAX INTEGER { createAndGo(4), destroy(6) } + DESCRIPTION + "Support for createAndWait and notInService is not + required." + + OBJECT jnxMplsFecAddrFamily + SYNTAX InetAddressType + DESCRIPTION + "An implementation is only required to support + + 'unknown(0)', and IPv4 addresses. Supporting + IPv6 addresses is optional." + + OBJECT jnxMplsFecAddr + SYNTAX InetAddress (SIZE(0|4|16)) + DESCRIPTION + "An implementation is only required to support IPv4 and + may optionally support IPv6 addresses." + + OBJECT jnxMplsFecRowStatus + SYNTAX INTEGER { active(1) } + WRITE-SYNTAX INTEGER { createAndGo(4), destroy(6) } + MIN-ACCESS read-only + DESCRIPTION + "Support for createAndWait and notInService is not + required. Also, the entries in this table may be + created by the agent, so strictly speaking + read-create functionality is not necessary, but + may be nice to have." + + OBJECT jnxMplsLdpLspFecRowStatus + SYNTAX INTEGER { active(1) } + WRITE-SYNTAX INTEGER { createAndGo(4), destroy(6) } + MIN-ACCESS read-only + DESCRIPTION + "Support for createAndWait and notInService is not + required. Also, the entries in this table may be + created by the agent, so strictly speaking + read-create functionality is not necessary, but + may be nice to have." + + OBJECT jnxMplsLdpSesPeerNextHopAddrType + SYNTAX InetAddressType + DESCRIPTION + "An implementation is only required to support + 'unknown(0)', and IPv4 addresses. Supporting + IPv6 addresses is optional." + + OBJECT jnxMplsLdpSesPeerNextHopAddr + SYNTAX InetAddress (SIZE(0|4|16)) + DESCRIPTION + "An implementation is only required to support IPv4 + and may optionally support IPv6 addresses." + + + ::= { jnxMplsLdpCompliances 1 } + +-- +-- Read-Only Compliance +-- + +jnxMplsLdpModuleReadOnlyCompliance MODULE-COMPLIANCE + STATUS current + DESCRIPTION + "The Module is implemented with support + for read-only. In other words, only monitoring + is available by implementing this MODULE-COMPLIANCE." + + MODULE -- this module + MANDATORY-GROUPS { jnxMplsLdpGeneralGroup, + jnxMplsLdpLspGroup, + jnxMplsLdpNotificationsGroup + } + + + GROUP jnxMplsLdpLsrGroup + DESCRIPTION + "This group must be supported if the LSR MIB is + implemented, specifically the mplsInSegmentTable, + the mplsOutSegmentTable or the mplsXCTable." + + OBJECT jnxMplsLdpEntityProtocolVersion + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityAdminStatus + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityTcpDscPort + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityUdpDscPort + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityMaxPduLength + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityKeepAliveHoldTimer + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityHelloHoldTimer + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityInitSesThreshold + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityLabelDistMethod + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityLabelRetentionMode + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityPathVectorLimit + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityHopCountLimit + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityTargetPeer + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityTargetPeerAddrType + SYNTAX InetAddressType + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required. + An implementation is only required to support + 'unknown(0)', and IPv4 addresses. Supporting + IPv6 addresses is optional." + + OBJECT jnxMplsLdpEntityTargetPeerAddr + SYNTAX InetAddress (SIZE(0|4|16)) + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required. + An implementation is only required to support IPv4 and + + may optionally support IPv6 addresses." + + OBJECT jnxMplsLdpEntityLabelType + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityStorageType + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsLdpEntityRowStatus + SYNTAX INTEGER { active(1) } + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required, and active is the + only status that needs to be supported." + + OBJECT jnxMplsFecType + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsFecAddrLength + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsFecAddrFamily + SYNTAX InetAddressType + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required. + An implementation is only required to support + 'unknown(0)', and IPv4 addresses. Supporting + IPv6 addresses is optional." + + OBJECT jnxMplsFecAddr + SYNTAX InetAddress (SIZE(0|4|16)) + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required. + An implementation is only required to support IPv4 and + may optionally support IPv6 addresses." + + OBJECT jnxMplsFecStorageType + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT jnxMplsFecRowStatus + SYNTAX INTEGER { active(1) } + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required, and active is the + only status that needs to be supported." + + OBJECT jnxMplsLdpLspFecRowStatus + SYNTAX INTEGER { active(1) } + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required, and active is the + only status that needs to be supported." + + OBJECT jnxMplsLdpSesPeerNextHopAddrType + SYNTAX InetAddressType + DESCRIPTION + "An implementation is only required to support + 'unknown(0)', and IPv4 addresses. Supporting + IPv6 addresses is optional." + + + OBJECT jnxMplsLdpSesPeerNextHopAddr + SYNTAX InetAddress (SIZE(0|4|16)) + DESCRIPTION + "An implementation is only required to support IPv4 + and may optionally support IPv6 addresses." + + ::= { jnxMplsLdpCompliances 2 } + + +-- units of conformance + +jnxMplsLdpGeneralGroup OBJECT-GROUP + OBJECTS { + jnxMplsLdpLsrId, + jnxMplsLdpLsrLoopDetectionCapable, + jnxMplsLdpEntityLastChange, + jnxMplsLdpEntityIndexNext, + jnxMplsLdpEntityProtocolVersion, + jnxMplsLdpEntityAdminStatus, + jnxMplsLdpEntityOperStatus, + jnxMplsLdpEntityTcpDscPort, + jnxMplsLdpEntityUdpDscPort, + jnxMplsLdpEntityMaxPduLength, + jnxMplsLdpEntityKeepAliveHoldTimer, + jnxMplsLdpEntityHelloHoldTimer, + jnxMplsLdpEntityInitSesThreshold, + jnxMplsLdpEntityLabelDistMethod, + jnxMplsLdpEntityLabelRetentionMode, + + jnxMplsLdpEntityPathVectorLimit, + jnxMplsLdpEntityHopCountLimit, + jnxMplsLdpEntityTargetPeer, + jnxMplsLdpEntityTargetPeerAddrType, + jnxMplsLdpEntityTargetPeerAddr, + jnxMplsLdpEntityLabelType, + jnxMplsLdpEntityDiscontinuityTime, + jnxMplsLdpEntityStorageType, + jnxMplsLdpEntityRowStatus, + jnxMplsLdpAttemptedSessions, + jnxMplsLdpSesRejectedNoHelloErrors, + jnxMplsLdpSesRejectedAdErrors, + jnxMplsLdpSesRejectedMaxPduErrors, + jnxMplsLdpSesRejectedLRErrors, + jnxMplsLdpBadLdpIdentifierErrors, + jnxMplsLdpBadPduLengthErrors, + jnxMplsLdpBadMessageLengthErrors, + jnxMplsLdpBadTlvLengthErrors, + jnxMplsLdpMalformedTlvValueErrors, + jnxMplsLdpKeepAliveTimerExpErrors, + jnxMplsLdpShutdownNotifReceived, + jnxMplsLdpShutdownNotifSent, + jnxMplsLdpPeerLastChange, + jnxMplsLdpPeerLabelDistMethod, + jnxMplsLdpPeerPathVectorLimit, + jnxMplsLdpHelloAdjHoldTimeRem, + jnxMplsLdpHelloAdjType, + jnxMplsLdpSesStateLastChange, + jnxMplsLdpSesState, + jnxMplsLdpSesProtocolVersion, + jnxMplsLdpSesKeepAliveHoldTimeRem, + jnxMplsLdpSesMaxPduLength, + jnxMplsLdpSesDiscontinuityTime, + jnxMplsLdpSesStatsUnkMesTypeErrors, + jnxMplsLdpSesStatsUnkTlvErrors, + jnxMplsLdpSesPeerNextHopAddrType, + jnxMplsLdpSesPeerNextHopAddr, + jnxMplsFecIndexNext, + jnxMplsFecType, + jnxMplsFecAddrFamily, + jnxMplsFecAddrLength, + jnxMplsFecAddr, + jnxMplsFecStorageType, + jnxMplsFecRowStatus, + jnxMplsLdpLspFecOperStatus, + jnxMplsLdpLspFecLastChange, + jnxMplsLdpLspFecRowStatus + } + STATUS current + DESCRIPTION + + "Objects that apply to all MPLS LDP implementations." + ::= { jnxMplsLdpGroups 1 } + + +jnxMplsLdpLspGroup OBJECT-GROUP + OBJECTS { + jnxMplsLdpLspLabelType, + jnxMplsLdpLspType + } + STATUS current + DESCRIPTION + "These objects are specific to LDP LSPs." + ::= { jnxMplsLdpGroups 2 } + +jnxMplsLdpLsrGroup OBJECT-GROUP + OBJECTS { + jnxMplsLdpLspLsrInSegmentPointer, + jnxMplsLdpLspLsrOutSegmentPointer, + jnxMplsLdpLspLsrXCPointer + } + STATUS current + DESCRIPTION + "These objects are optional and only need to be supported + for LDP implementations which support the following + tables in the LSR MIB: mplsInSegmentTable, + mplsOutSegmentTable and mplsXCTable." + ::= { jnxMplsLdpGroups 3 } + + +jnxMplsLdpNotificationsGroup NOTIFICATION-GROUP + NOTIFICATIONS { jnxMplsLdpInitSesThresholdExceeded, + jnxMplsLdpPathVectorLimitMismatch, + jnxMplsLdpSessionUp, + jnxMplsLdpSessionDown + } + STATUS current + DESCRIPTION + "The notification(s) which an MPLS LDP implemention + is required to implement." + ::= { jnxMplsLdpGroups 4 } + + +END |