diff options
Diffstat (limited to 'MIBS/dlink/DLINKSW-LED-MIB')
| -rw-r--r-- | MIBS/dlink/DLINKSW-LED-MIB | 260 |
1 files changed, 260 insertions, 0 deletions
diff --git a/MIBS/dlink/DLINKSW-LED-MIB b/MIBS/dlink/DLINKSW-LED-MIB new file mode 100644 index 0000000..bc43e46 --- /dev/null +++ b/MIBS/dlink/DLINKSW-LED-MIB @@ -0,0 +1,260 @@ +-- *****************************************************************
+-- DLINKSW-LED-MIB.mib : LED Mib
+--
+-- Copyright (c) 2013 D-Link Corporation, all rights reserved.
+--
+-- *****************************************************************
+DLINKSW-LED-MIB DEFINITIONS ::= BEGIN
+
+ IMPORTS
+ OBJECT-GROUP, MODULE-COMPLIANCE
+ FROM SNMPv2-CONF
+ MODULE-IDENTITY, OBJECT-TYPE
+ FROM SNMPv2-SMI
+ dlinkIndustrialCommon
+ FROM DLINK-ID-REC-MIB;
+
+ dlinkSwLedMIB MODULE-IDENTITY
+ LAST-UPDATED "201309130000Z"
+ ORGANIZATION "D-Link Corp."
+ CONTACT-INFO
+ " D-Link Corporation
+ Postal: No. 289, Sinhu 3rd Rd., Neihu District,
+ Taipei City 114, Taiwan, R.O.C
+ Tel: +886-2-66000123
+ E-mail: tsd@dlink.com.tw
+ "
+ DESCRIPTION
+ "A MIB module for LED status.
+ "
+ REVISION "201309130000Z"
+ DESCRIPTION
+ "Add 'LED off' state for stackingID(12) LED."
+
+ REVISION "201309060000Z"
+ DESCRIPTION
+ "Initial version of this MIB module."
+ ::= { dlinkIndustrialCommon 163 }
+
+-- -----------------------------------------------------------------------------
+ dLedMIBNotifications OBJECT IDENTIFIER ::= { dlinkSwLedMIB 0 }
+ dLedMIBObjects OBJECT IDENTIFIER ::= { dlinkSwLedMIB 1 }
+ dLedMIBConformance OBJECT IDENTIFIER ::= { dlinkSwLedMIB 2 }
+
+--------------------------------------------------------------------------------
+
+ dLedInfoTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF DLedInfoEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table consists of a list of information of LEDs."
+ ::= { dLedMIBObjects 1 }
+
+ dLedInfoEntry OBJECT-TYPE
+ SYNTAX DLedInfoEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "An entry contains information of one box."
+ INDEX {dLedBoxId}
+ ::= { dLedInfoTable 1 }
+
+ DLedInfoEntry ::=
+ SEQUENCE {
+ dLedBoxId
+ INTEGER,
+ dLedSysLedStatus
+ OCTET STRING,
+ dLedIfLedStatus
+ OCTET STRING
+ }
+
+ dLedBoxId OBJECT-TYPE
+ SYNTAX INTEGER
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This variable uniquely identifies the box in the stack, module in a
+ rack and the value 1 MUST be used for non-modular devices."
+ ::= { dLedInfoEntry 1 }
+
+ dLedSysLedStatus OBJECT-TYPE
+ SYNTAX OCTET STRING
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object is a set of system LED indicators.
+ Every type LED's format is as follow:
+ +-------------------------------------+
+ | LED | LED | Data |...| Data |
+ | Type | Length | | | |
+ +-------------------------------------+
+ 1octet 1octet 3octet
+
+ LED Type(1 octet):
+ rps(1) - indicates RPS LED,
+ console(2) - indicates console LED,
+ master(3) - indicates device role LED,
+ sdCard(4) - indicates SD card LED,
+ linkMode(5) - indicates link mode LED,
+ poeMode(6) - indicates PoE mode LED,
+ alarm(7) - indicates alarm LED,
+ sysPower(8) - indicates system power LED,
+ mgmtPort(9) - indicates management port LED,
+ fan(10) - indicates device's fan LED,
+ sioPort(11) - indicates SIO port LED,
+ stackingID(12) - indicates stacking ID LED
+
+ LED Length(1 octet): indicates Data's length of a specified LED type in number of octets.
+
+ Data(3 octets): indicates LED status of specified LED type. Three consecutive octets are used
+ to represent the information of one LED. If given LED type has more than one LEDs,
+ there are multiple such triads in the data field.
+
+ If LED Type is stackingID(12), below predefined values represent stacking ID LED's
+ status, with the most significant byte in the first octet.
+ index box id LED display
+ 0x0 -- '0'
+ 0x1 -- '1'
+ 0x2 -- '2'
+ 0x3 -- '3'
+ 0x4 -- '4'
+ 0x5 -- '5'
+ 0x6 -- '6'
+ 0x7 -- '7'
+ 0x8 -- '8'
+ 0x9 -- '9'
+ 0xA -- '10'
+ 0xB -- '11'
+ 0xC -- '12'
+ 0xD -- '13'
+ 0xE -- '14'
+ 0xF -- '15'
+ 0x10 -- '16'
+ 0x11 -- '17'
+ 0x12 -- '18'
+ 0x13 -- '19'
+ 0x100 -- 'H'
+ 0x101 -- 'h'
+ 0x102 -- 'E'
+ 0x103 -- 'G'
+
+ 0xfff -- LED off state
+
+ Else these 3 octets shows LED's status value,format is as below:
+ +-------------------------+
+ | LED Instance | LED |
+ | Index | Status |
+ +-------------------------+
+ 1 octet 2 octet
+
+ LED instance index(high octet) indicates the instance ID of specified LED type.
+ For example, if the LED type is fan(10), it is the fan ID.
+
+ LED status(low 2 octets) is the status of one LED. Its data format is as below:
+ +-----------------------+
+ | Color | LED Lighting |
+ | Bits | Mode |
+ +-----------------------+
+ 15 4 3 0
+
+ Bit0 to bit3 indicates the mode of LED lighting.
+ 0x0 means this LED is not supported.
+ 0x1 means LED is off.
+ 0x2 means LED is fixed lighting.
+ 0x3 indicates LED is blinking.
+ 0x4 indicates LED is alternating lighting between more than one color.
+ Colors are determined by color bits.
+ 0x5-0xF are reserved.
+
+ Bit4 to bit15 are color bits, they indicate the LED's specific color. If a
+ color bit is set, it stands for corresponding color. Only when LED lighting mode
+ is alternating lighting(low nibble is 0x4), multi-bit can be set.
+ bit4 - green bit
+ bit5 - amber bit
+ bit6 - red bit
+ bit7-bit15 are reserved.
+
+ If a LED instance consists of more LEDs, for example, if power source has separate input, state
+ LEDs, there will be two LED data and their instance index is the same power ID. One LED data for the input LED,
+ another for the state LED. The meaning of each LED data is device based.
+ +---------------------------------------------------------------------------------------------+
+ | sysPower(8) | 12 | power1 | LED | power1 | LED | power2 | LED | power2 | LED |...
+ | | | | Status | | Status | | Status | | Status |
+ +---------------------------------------------------------------------------------------------+
+ "
+
+ ::= { dLedInfoEntry 2 }
+
+ dLedIfLedStatus OBJECT-TYPE
+ SYNTAX OCTET STRING
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object is a set of ethernet port LED indicators. Format is as follow:
+ +--------------------------------------------+
+ | Total Port | Port1 |....| PortN |
+ | Number | LED Status | | LED Status |
+ +--------------------------------------------+
+ 1octets 2octets
+
+ Total Port Number(1 octet): indicates the number of following port LED status.
+
+ Port LED Status(2 octets): indicates one ethernet port LED's status, format is as below:
+ +-----------------------+
+ | Color | LED lighting |
+ | bits | mode |
+ +-----------------------+
+ 15 4 3 0
+
+ Bit0 to bit3 indicates the mode of LED lighting.
+ 0x0 means this LED is not supported.
+ 0x1 means LED is off.
+ 0x2 means LED is fixed lighting.
+ 0x3 indicates LED is blinking.
+ 0x4 indicates LED is alternating lighting between more than one color.
+ Colors are determined by color bits.
+ 0x5-0xF are reserved.
+
+ Bit4 to bit15 are color bits,they indicate the LED's specific color. If a
+ color bit is set, it stands for corresponding color. Only when LED lighting mode
+ is alternating lighting(low nibble is 0x4), multi-bit can be set.
+ bit4 - green bit
+ bit5 - amber bit
+ bit6 - red bit
+ bit7-bit15 are reserved.
+
+ Each LED Status corresponds to one port, all ethernet port LEDs' status are arranged
+ from lowest number port to high.
+ "
+ ::= { dLedInfoEntry 3 }
+
+-- *****************************************************************************
+-- MIB Conformance statements
+-- *****************************************************************************
+ dLedMIBCompliances OBJECT IDENTIFIER ::= { dLedMIBConformance 1 }
+
+ dLedMIBGroups OBJECT IDENTIFIER ::= { dLedMIBConformance 2 }
+ dLedMIBCompliance MODULE-COMPLIANCE
+ STATUS current
+ DESCRIPTION
+ "The compliance statement for entities which implement the
+ DLINKSW-LED-MIB."
+ MODULE -- this module
+ MANDATORY-GROUPS {
+ dLedInfoGroup
+ }
+ ::= { dLedMIBCompliances 1 }
+
+ dLedInfoGroup OBJECT-GROUP
+ OBJECTS {
+ dLedSysLedStatus,
+ dLedIfLedStatus
+ }
+ STATUS current
+ DESCRIPTION
+ "A collection of objects to display the LED status."
+ ::= { dLedMIBGroups 1 }
+
+END
\ No newline at end of file |