diff options
Diffstat (limited to 'MIBS/delta/DeltaUPS-MIB')
| -rw-r--r-- | MIBS/delta/DeltaUPS-MIB | 1666 |
1 files changed, 1666 insertions, 0 deletions
diff --git a/MIBS/delta/DeltaUPS-MIB b/MIBS/delta/DeltaUPS-MIB new file mode 100644 index 0000000..e886191 --- /dev/null +++ b/MIBS/delta/DeltaUPS-MIB @@ -0,0 +1,1666 @@ +--Delta-MIB { iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) delta(2254) ups(2) upsv4(4) } + + +DeltaUPS-MIB DEFINITIONS ::= BEGIN + + +IMPORTS + enterprises, IpAddress + FROM RFC1155-SMI + DisplayString + FROM RFC1213-MIB + OBJECT-TYPE + FROM RFC-1212 + TRAP-TYPE + FROM RFC-1215; + + +delta OBJECT IDENTIFIER ::= { enterprises 2254 } + +ups OBJECT IDENTIFIER ::= { delta 2 } + +upsv4 OBJECT IDENTIFIER ::= { ups 4 } + +dupsIdent OBJECT IDENTIFIER ::= { upsv4 1 } +dupsControl OBJECT IDENTIFIER ::= { upsv4 2 } +dupsConfig OBJECT IDENTIFIER ::= { upsv4 3 } +dupsInput OBJECT IDENTIFIER ::= { upsv4 4 } +dupsOutput OBJECT IDENTIFIER ::= { upsv4 5 } +dupsBypass OBJECT IDENTIFIER ::= { upsv4 6 } +dupsBattery OBJECT IDENTIFIER ::= { upsv4 7 } +dupsTest OBJECT IDENTIFIER ::= { upsv4 8 } +dupsAlarm OBJECT IDENTIFIER ::= { upsv4 9 } +dupsEnvironment OBJECT IDENTIFIER ::= { upsv4 10 } +dupsTraps OBJECT IDENTIFIER ::= { upsv4 20 } + + +---------------------- +-- dups Ident group -- +---------------------- + dupsIdentManufacturer OBJECT-TYPE + SYNTAX DisplayString (SIZE(0..20)) + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The name of the UPS manufacturer." + ::= { dupsIdent 1 } + + dupsIdentModel OBJECT-TYPE + SYNTAX DisplayString (SIZE(0..31)) + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The UPS Model designation." + ::= { dupsIdent 2 } + + dupsIdentUPSSoftwareVersion OBJECT-TYPE + SYNTAX DisplayString (SIZE(0..15)) + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The UPS firmware/software version(s). This variable + may or may not has the same value as + upsIdentAgentSoftwareVersion in some implementations." + ::= { dupsIdent 3 } + + dupsIdentAgentSoftwareVersion OBJECT-TYPE + SYNTAX DisplayString (SIZE(0..15)) + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The UPS agent software version. This variable may or + may not has the same value as + upsIdentUPSSoftwareVersion in some implementations." + ::= { dupsIdent 4 } + + dupsIdentName OBJECT-TYPE + SYNTAX DisplayString (SIZE(0..63)) + ACCESS read-write + STATUS mandatory + DESCRIPTION + "A string identifying the UPS. This object should be + set by the administrator." + ::= { dupsIdent 5 } + + dupsAttachedDevices OBJECT-TYPE + SYNTAX DisplayString (SIZE(0..63)) + ACCESS read-write + STATUS mandatory + DESCRIPTION + "A string identifying the devices attached to the + output(s) of the UPS. This object should be set by + the administrator." + ::= { dupsIdent 6 } + + dupsRatingOutputVA OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The magnitude of the nominal output VA rating." + ::= { dupsIdent 7 } + + dupsRatingOutputVoltage OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The magnitude of the nominal output voltage rating." + ::= { dupsIdent 8 } + + dupsRatingOutputFrequency OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The magnitude of the nominal output frequency rating." + ::= { dupsIdent 9 } + + dupsRatingInputVoltage OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The magnitude of the nominal input voltage rating." + ::= { dupsIdent 10 } + + dupsRatingInputFrequency OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The magnitude of the nominal input frequency rating." + ::= { dupsIdent 11 } + + dupsRatingBatteryVoltage OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The magnitude of the nominal battery voltage rating." + ::= { dupsIdent 12 } + + dupsLowTransferVoltUpBound OBJECT-TYPE + SYNTAX INTEGER + UNITS "Volt" + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The minimum input line voltage upper bound allowed + before the UPS system transfers to battery backup." + ::= { dupsIdent 13 } + + dupsLowTransferVoltLowBound OBJECT-TYPE + SYNTAX INTEGER + UNITS "Volt" + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The minimum input line voltage lower bound allowed + before the UPS system transfers to battery backup." + ::= { dupsIdent 14 } + + dupsHighTransferVoltUpBound OBJECT-TYPE + SYNTAX INTEGER + UNITS "Volt" + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The maximum input line voltage upper bound allowed + before the UPS system transfers to battery backup." + ::= { dupsIdent 15 } + + dupsHighTransferVoltLowBound OBJECT-TYPE + SYNTAX INTEGER + UNITS "Volt" + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The maximum input line voltage lower bound allowed + before the UPS system transfers to battery backup." + ::= { dupsIdent 16 } + + dupsLowBattTime OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Minutes, time from low battery to low battery shutdown." + ::= { dupsIdent 17 } + + dupsOutletRelays OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Number of outlet relay. If it is 0, the function is not + available for the UPS." + ::= { dupsIdent 18 } + + dupsType OBJECT-TYPE + SYNTAX INTEGER { + on-line(1), + off-line(2), + line-interactive(3), + 3phase(4), + splite-phase(5) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Indicate the UPS type." + ::= { dupsIdent 19 } + +------------------------ +-- dups Control group -- +------------------------ + dupsShutdownType OBJECT-TYPE + SYNTAX INTEGER { + output(1), + system(2) + } + ACCESS read-write + STATUS mandatory + DESCRIPTION + "This object determines the nature of the action to be + taken at the time when the countdown of the + upsShutdownAfterDelay and upsRebootWithDuration + objects reaches zero. + Setting this object to output(1) indicates that + shutdown requests should cause only the output of the + UPS to turn off. Setting this object to system(2) + indicates that shutdown requests will cause the entire + UPS system to turn off." + ::= { dupsControl 1 } + + dupsAutoReboot OBJECT-TYPE + SYNTAX INTEGER { + on(1), + off(2) + } + ACCESS read-write + STATUS mandatory + DESCRIPTION + "In backup mode, the UPS may shutdown normally by SDA command, + dry-contact remote shutdown signal or low battery shutdown. + This command is used to determine the unit should restart or + not next time when the power restores" + ::= { dupsControl 2 } + + dupsShutdownAction OBJECT-TYPE + SYNTAX INTEGER +-- UNITS "Second" + ACCESS read-write + STATUS mandatory + DESCRIPTION + "If the value is greater than 0 the UPS performs + shutdown action that defined by ShutdownType after + the seconds. 0, aborted." + ::= { dupsControl 3 } + + dupsRestartAction OBJECT-TYPE + SYNTAX INTEGER +-- UNITS "Minute" + ACCESS read-write + STATUS mandatory + DESCRIPTION + "UPS will restart after the indicated number of minutes. + -1, aborted." + ::= { dupsControl 4 } + + dupsSetOutletRelay OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-write + STATUS mandatory + DESCRIPTION + "Indicate which outlet relay, from 1,2,3... ." + ::= { dupsControl 5 } + + dupsRelayOffDelay OBJECT-TYPE + SYNTAX INTEGER +-- UNITS "Second" + ACCESS read-write + STATUS mandatory + DESCRIPTION + "Turn the relay off after the seconds. The relay was indicated + by SetOutletRelay." + ::= { dupsControl 6 } + + dupsRelayOnDelay OBJECT-TYPE + SYNTAX INTEGER +-- UNITS "Minute" + ACCESS read-write + STATUS mandatory + DESCRIPTION + "Turn the relay on after the seconds. The relay was indicated + by SetOutletRelay." + ::= { dupsControl 7 } + +-------------------------- +-- dups Configure group -- +-------------------------- + dupsConfigBuzzerAlarm OBJECT-TYPE + SYNTAX INTEGER { + alarm(1), + silence(2) + } + ACCESS read-write + STATUS mandatory + DESCRIPTION + "UPS will keep silence but will alarm again when + next power event is occurred" + ::= { dupsConfig 1 } + + dupsConfigBuzzerState OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2) + } + ACCESS read-write + STATUS mandatory + DESCRIPTION + "If it is disabled then the UPS is always muted." + ::= { dupsConfig 2 } + + dupsConfigSensitivity OBJECT-TYPE + SYNTAX INTEGER { + normal(0), + reduced(1), + low(2) + } + ACCESS read-write + STATUS mandatory + DESCRIPTION + "The seneitivity of the UPS to utility line + abnormalities or noises." + ::= { dupsConfig 3 } + + dupsConfigLowVoltageTransferPoint OBJECT-TYPE + SYNTAX INTEGER + UNITS "Volt" + ACCESS read-write + STATUS mandatory + DESCRIPTION + "The minimum input line voltage allowed before the UPS + system transfers to battery backup." + ::= { dupsConfig 4 } + + dupsConfigHighVoltageTransferPoint OBJECT-TYPE + SYNTAX INTEGER + UNITS "Volt" + ACCESS read-write + STATUS mandatory + DESCRIPTION + "The maximum line voltage allowed before the UPS + system transfers to battery backup." + ::= { dupsConfig 5 } + + dupsConfigShutdownOSDelay OBJECT-TYPE + SYNTAX INTEGER + UNITS "Second" + ACCESS read-write + STATUS mandatory + DESCRIPTION + "The operating system shutdown delay time when the + input power fail. -1 will disable this option." + ::= { dupsConfig 6 } + + dupsConfigUPSBootDelay OBJECT-TYPE + SYNTAX INTEGER + UNITS "Second" + ACCESS read-write + STATUS mandatory + DESCRIPTION + "Delay the UPS startup after power restores. The power + quality may not stable when power restores, this + feature let the UPS wait a period of time to startup + the system." + ::= { dupsConfig 7 } + + dupsConfigExternalBatteryPack OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-write + STATUS mandatory + DESCRIPTION + "Indicate the number of external battery pack." + ::= { dupsConfig 8 } + +---------------------- +-- dups Input group -- +---------------------- + dupsInputNumLines OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The number of input lines utilized in this device." + ::= { dupsInput 1 } + + dupsInputFrequency1 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The current input line 1 frequency to the UPS + system in 1/10 Hz." + ::= { dupsInput 2 } + + dupsInputVoltage1 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Input line 1 voltage of the UPS system in 1/10 V." + ::= { dupsInput 3 } + + dupsInputCurrent1 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Input line 1 current to the UPS system in 1/10 A." + ::= { dupsInput 4 } + + dupsInputFrequency2 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The current input line 2 frequency to the UPS system + in 1/10 Hz." + ::= { dupsInput 5 } + + dupsInputVoltage2 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Input line 2 voltage of the UPS system in 1/10 V." + ::= { dupsInput 6 } + + dupsInputCurrent2 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Input line 2 current to the UPS system in 1/10 A." + ::= { dupsInput 7 } + + dupsInputFrequency3 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The current input line 3 frequency to the UPS system + in 1/10 Hz." + ::= { dupsInput 8 } + + dupsInputVoltage3 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Input line 3 voltage of the UPS system in 1/10 V." + ::= { dupsInput 9 } + + dupsInputCurrent3 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Input line 3 current to the UPS system in 1/10 A." + ::= { dupsInput 10 } + +----------------------- +-- dups Output group -- +----------------------- + dupsOutputSource OBJECT-TYPE + SYNTAX INTEGER { + normal(0), + battery(1), + bypass(2), + reducing(3), + boosting(4), + manualBypass(5), + other(6), + none(7) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The present source of output power. The enumeration + none(7) indicates that there is no source of output + power (and therefore no output power), for example, + the system has opened the output breaker." + ::= { dupsOutput 1 } + + dupsOutputFrequency OBJECT-TYPE + SYNTAX INTEGER + UNITS "0.1 Hertz" + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The present output frequency in 1/10 Hz." + ::= { dupsOutput 2 } + + dupsOutputNumLines OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The number of output lines utilized in this device." + ::= { dupsOutput 3 } + + dupsOutputVoltage1 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Output line 1 voltage of the UPS system in 1/10 V." + ::= { dupsOutput 4 } + + dupsOutputCurrent1 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Output line 1 current of the UPS system in 1/10 A." + ::= { dupsOutput 5 } + + dupsOutputPower1 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Output line 1 real power of the UPS system in watts." + ::= { dupsOutput 6 } + + dupsOutputLoad1 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The current UPS output line 1 load expressed in percent + of rated capacity." + ::= { dupsOutput 7 } + + dupsOutputVoltage2 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Output line 2 voltage of the UPS system in 1/10 V." + ::= { dupsOutput 8 } + + dupsOutputCurrent2 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Output line 2 current of the UPS system in 1/10 A." + ::= { dupsOutput 9 } + + dupsOutputPower2 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Output line 2 real power of the UPS system in watts." + ::= { dupsOutput 10 } + + dupsOutputLoad2 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The current UPS output line 2 load expressed in percent + of rated capacity." + ::= { dupsOutput 11 } + + dupsOutputVoltage3 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Output line 3 voltage of the UPS system in 1/10 V." + ::= { dupsOutput 12 } + + dupsOutputCurrent3 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Output line 3 current of the UPS system in 1/10 A." + ::= { dupsOutput 13 } + + dupsOutputPower3 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The Output line 3 real power of the UPS system in watts." + ::= { dupsOutput 14 } + + dupsOutputLoad3 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The current UPS output line 3 load expressed in percent + of rated capacity." + ::= { dupsOutput 15 } + +----------------------- +-- dups Bypass group -- +----------------------- + dupsBypassFrequency OBJECT-TYPE + SYNTAX INTEGER + UNITS "0.1 Hertz" + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The present bypass frequency in 1/10 Hz." + ::= { dupsBypass 1 } + + dupsBypassNumLines OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The number of bypass lines utilized in this device." + ::= { dupsBypass 2 } + + dupsBypassVoltage1 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The bypass line 1 voltage of the UPS system in 1/10 V." + ::= { dupsBypass 3 } + + dupsBypassCurrent1 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The bypass line 1 current of the UPS system in 1/10 A." + ::= { dupsBypass 4 } + + dupsBypassPower1 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The bypass line 1 real power of the UPS system in watts." + ::= { dupsBypass 5 } + + dupsBypassVoltage2 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The bypass line 2 voltage of the UPS system in 1/10 V." + ::= { dupsBypass 6 } + + dupsBypassCurrent2 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The bypass line 2 current of the UPS system in 1/10 A." + ::= { dupsBypass 7 } + + dupsBypassPower2 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The bypass line 2 real power of the UPS system in watts." + ::= { dupsBypass 8 } + + dupsBypassVoltage3 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The bypass line 3 voltage of the UPS system in 1/10 V." + ::= { dupsBypass 9 } + + dupsBypassCurrent3 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The bypass line 3 current of the UPS system in 1/10 A." + ::= { dupsBypass 10 } + + dupsBypassPower3 OBJECT-TYPE + SYNTAX INTEGER + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The bypass line 3 real power of the UPS system in watts." + ::= { dupsBypass 11 } + +------------------------ +-- dups Battery group -- +------------------------ + dupsBatteryCondiction OBJECT-TYPE + SYNTAX INTEGER { + good(0), + weak(1), + replace(2) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The indication of the capacity remaining in the UPS + system's batteries when AC normal." + ::= { dupsBattery 1 } + + dupsBatteryStatus OBJECT-TYPE + SYNTAX INTEGER { + ok(0), + low(1), + depleted(2) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The indication of the capacity remaining in the UPS + system's batteries when AC failed. A value of ok + indicates that the remaining run-time is greater than + upsConfigLowBattTime. A value of low indicates + that the remaining battery run-time is less than or + equal to upsConfigLowBattTime. A value of + depleted indicates that the UPS will be unable + to sustain the present load when and if the utility + power is lost (including the possibility that the + utility power is currently absent and the UPS is + unable to sustain the output)." + ::= { dupsBattery 2 } + + dupsBatteryCharge OBJECT-TYPE + SYNTAX INTEGER { + floating(0), + charging(1), + resting(2), + discharging(3) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "" + ::= { dupsBattery 3 } + + dupsSecondsOnBattery OBJECT-TYPE + SYNTAX INTEGER + UNITS "seconds" + ACCESS read-only + STATUS mandatory + DESCRIPTION + "If the unit is on battery power, the elapsed time + since the UPS last switched to battery power, or the + time since the network management subsystem was last + restarted, whichever is less. Zero shall be returned + if the unit is not on battery power." + ::= { dupsBattery 4 } + + dupsBatteryEstimatedTime OBJECT-TYPE + SYNTAX INTEGER + UNITS "minutes" + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Estimated time from backup to low battery shutdown." + ::= { dupsBattery 5 } + + dupsBatteryVoltage OBJECT-TYPE + SYNTAX INTEGER + UNITS "0.1 Volt DC" + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The magnitude of the present battery voltage + in 1/10 V." + ::= { dupsBattery 6 } + + dupsBatteryCurrent OBJECT-TYPE + SYNTAX INTEGER + UNITS "0.1 Amp DC" + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The present battery current in 1/10 A." + ::= { dupsBattery 7 } + + dupsBatteryCapacity OBJECT-TYPE + SYNTAX INTEGER (0..100) + UNITS "percent" + ACCESS read-only + STATUS mandatory + DESCRIPTION + "An estimate of the battery charge remaining expressed + as a percent of full charge." + ::= { dupsBattery 8 } + + dupsTemperature OBJECT-TYPE + SYNTAX INTEGER + UNITS "degrees Centigrade" + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The ambient temperature at or near the UPS Battery + casing." + ::= { dupsBattery 9 } + + dupsLastReplaceDate OBJECT-TYPE + SYNTAX DisplayString (SIZE(0..8)) + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The last battery replacement date. The format is YYYYMMDD." + ::= { dupsBattery 10 } + + dupsNextReplaceDate OBJECT-TYPE + SYNTAX DisplayString (SIZE(0..8)) + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The next battery replacement date. The format is YYYYMMDD." + ::= { dupsBattery 11 } + +------------------- +-- dups Test group +------------------- + dupsTestType OBJECT-TYPE + SYNTAX INTEGER { + abort(0), + generalTest(1), + batteryTest(2), + testFor10sec(3), + testUntilBattlow(4) + } + ACCESS read-write + STATUS mandatory + DESCRIPTION + "Perform the UPS Test procedure." + ::= { dupsTest 1 } + + dupsTestResultsSummary OBJECT-TYPE + SYNTAX INTEGER { + noTestsInitiated(0), + donePass(1), + inProgress(2), + generalTestFail(3), + batteryTestFail(4), + deepBatteryTestFail(5) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The results of the current or last UPS diagnostics + test performed. The values for donePass(1), + generalTestFail(3), and batteryTestFail(4) indicate that the + test completed either successfully, with a warning, or + with an error, respectively.Tests which have not yet + concluded are indicated by inProgress(2). The value + noTestsInitiated(0) indicates that no previous test + results are available." + ::= { dupsTest 2 } + + dupsTestResultsDetail OBJECT-TYPE + SYNTAX DisplayString (SIZE (0..255)) + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Additional information about upsTestResultsSummary. + If no additional information available, a zero length + string is returned." + ::= { dupsTest 3 } + +----------------------- +-- dups Alarm group -- +----------------------- + dupsAlarmDisconnect OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS disconnect?" + ::= { dupsAlarm 1 } + + dupsAlarmPowerFail OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the input power fail?" + ::= { dupsAlarm 2 } + + dupsAlarmBatteryLow OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Are the UPS batteries low?" + ::= { dupsAlarm 3 } + + dupsAlarmLoadWarning OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS load percent over the load warning value?" + ::= { dupsAlarm 4 } + + dupsAlarmLoadSeverity OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS load percent over the load severity value?" + ::= { dupsAlarm 5 } + + dupsAlarmLoadOnBypass OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS load on bypass?" + ::= { dupsAlarm 6 } + + dupsAlarmUPSFault OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS general fail?" + ::= { dupsAlarm 7 } + + dupsAlarmBatteryGroundFault OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS battery ground fault?" + ::= { dupsAlarm 8 } + + dupsAlarmTestInProgress OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS test in progress?" + ::= { dupsAlarm 9 } + + dupsAlarmBatteryTestFail OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS test fail?" + ::= { dupsAlarm 10 } + + dupsAlarmFuseFailure OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS fuse failure?" + ::= { dupsAlarm 11 } + + dupsAlarmOutputOverload OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS output overload?" + ::= { dupsAlarm 12 } + + dupsAlarmOutputOverCurrent OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS output overcurrent?" + ::= { dupsAlarm 13 } + + dupsAlarmInverterAbnormal OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS inverter abnormal?" + ::= { dupsAlarm 14 } + + dupsAlarmRectifierAbnormal OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS rectifier abnormal?" + ::= { dupsAlarm 15 } + + dupsAlarmReserveAbnormal OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS reserve abnormal?" + ::= { dupsAlarm 16 } + + dupsAlarmLoadOnReserve OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS load on reserve?" + ::= { dupsAlarm 17 } + + dupsAlarmOverTemperature OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS over heat?" + ::= { dupsAlarm 18 } + + dupsAlarmOutputBad OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Is the UPS output abnormal?" + ::= { dupsAlarm 19 } + + dupsAlarmBypassBad OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Is the UPS bypass bad?" + ::= { dupsAlarm 20 } + + dupsAlarmUPSOff OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Is the UPS in standby mode?" + ::= { dupsAlarm 21 } + + dupsAlarmChargerFail OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS charger fail?" + ::= { dupsAlarm 22 } + + dupsAlarmFanFail OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the UPS fan fail?" + ::= { dupsAlarm 23 } + + dupsAlarmEconomicMode OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Indicates whether the UPS is in the economic mode." + ::= { dupsAlarm 24 } + + dupsAlarmOutputOff OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Indicates whether the UPS output is turned off or not." + ::= { dupsAlarm 25 } + + dupsAlarmSmartShutdown OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Indicates whether the Smart Shutdown is in progress." + ::= { dupsAlarm 26 } + + dupsAlarmEmergencyPowerOff OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "UPS emergency power off." + ::= { dupsAlarm 27 } + + dupsAlarmUPSShutdown OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "UPS shutdown." + ::= { dupsAlarm 28 } + +----------------------- +-- dups Environment group -- +----------------------- + + dupsEnvTemperature OBJECT-TYPE + SYNTAX INTEGER + UNITS "degrees Centigrade" + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The ambient environmental temperature." + ::= { dupsEnvironment 1 } + + dupsEnvHumidity OBJECT-TYPE + SYNTAX INTEGER + UNITS "percentage" + ACCESS read-only + STATUS mandatory + DESCRIPTION + "The environmental humidity." + ::= { dupsEnvironment 2 } + + dupsEnvSetTemperatureLimit OBJECT-TYPE + SYNTAX INTEGER + UNITS "degrees Centigrade" + ACCESS read-write + STATUS mandatory + DESCRIPTION + "Alarm dupsAlarmOverTemperature on when the environmental + temperature over the value." + ::= { dupsEnvironment 3 } + + dupsEnvSetHumidityLimit OBJECT-TYPE + SYNTAX INTEGER + UNITS "percentage" + ACCESS read-write + STATUS mandatory + DESCRIPTION + "Alarm dupsAlarmOverHumidity on when the environmental + humidity over the value." + ::= { dupsEnvironment 4 } + + dupsEnvSetEnvRelay1 OBJECT-TYPE + SYNTAX INTEGER{ + normalOpen(0), + normalClose(1) + } + ACCESS read-write + STATUS mandatory + DESCRIPTION + "" + ::= { dupsEnvironment 5 } + + dupsEnvSetEnvRelay2 OBJECT-TYPE + SYNTAX INTEGER{ + normalOpen(0), + normalClose(1) + } + ACCESS read-write + STATUS mandatory + DESCRIPTION + "" + ::= { dupsEnvironment 6 } + + dupsEnvSetEnvRelay3 OBJECT-TYPE + SYNTAX INTEGER{ + normalOpen(0), + normalClose(1) + } + ACCESS read-write + STATUS mandatory + DESCRIPTION + "" + ::= { dupsEnvironment 7 } + + dupsEnvSetEnvRelay4 OBJECT-TYPE + SYNTAX INTEGER{ + normalOpen(0), + normalClose(1) + } + ACCESS read-write + STATUS mandatory + DESCRIPTION + "" + ::= { dupsEnvironment 8 } + + dupsAlarmOverEnvTemperature OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the environment over temperature?" + ::= { dupsEnvironment 9 } + + dupsAlarmOverEnvHumidity OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "Does the environment over humidity?" + ::= { dupsEnvironment 10 } + + dupsAlarmEnvRelay1 OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "" + ::= { dupsEnvironment 11 } + + dupsAlarmEnvRelay2 OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "" + ::= { dupsEnvironment 12 } + + dupsAlarmEnvRelay3 OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "" + ::= { dupsEnvironment 13 } + + dupsAlarmEnvRelay4 OBJECT-TYPE + SYNTAX INTEGER{ + off(0), + on(1) + } + ACCESS read-only + STATUS mandatory + DESCRIPTION + "" + ::= { dupsEnvironment 14 } + +----------------------- +-- dups Trap group -- +----------------------- + + dupsCommunicationLost TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: Communication with the UPS failed." + ::= 1 + + dupsCommunicationEstablished TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: Communication with the UPS reestablished." + ::= 2 + + dupsPowerFail TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "WARNING: Power failed! The UPS is operating on battery power." + ::= 3 + + dupsPowerRestored TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: Power restored! The utility power restored." + ::= 4 + + dupsLowBattery TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: The UPS batteries are low and will soon be exhausted." + ::= 5 + + dupsReturnFromLowBattery TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The UPS has returned from a low battery condition." + ::= 6 + + dupsLoadWarning TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: Loading percent of the UPS over the Load Warning value." + ::= 7 + + dupsNoLongerLoadWarning TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: Returnd from Load Warning condition." + ::= 8 + + dupsLoadSeverity TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "Warning: Loading percent of the UPS over the Load Severity value." + ::= 9 + + dupsNoLongerLoadSeverity TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: Returned from Load Severity condition." + ::= 10 + + dupsLoadOnBypass TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: The UPS loads on bypass." + ::= 11 + + dupsNoLongerLoadOnBypass TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The UPS is not on bypass mode." + ::= 12 + + dupsUPSFault TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: A general fault caused in the UPS." + ::= 13 + + dupsReturnFromUPSFault TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The UPS is returned from general fault." + ::= 14 + + dupsBatteryGroundFault TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: The UPS battery ground fault." + ::= 15 + + dupsNoLongerBatteryFault TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The UPS recovered from battery ground fault." + ::= 16 + + dupsTestInProgress TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The UPS test in progress." + ::= 17 + + dupsBatteryTestFail TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: The UPS test fail." + ::= 18 + + dupsFuseFailure TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: The UPS fuse failed." + ::= 19 + + dupsFuseRecovered TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The UPS fuse recovered." + ::= 20 + + dupsOutputOverload TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: The UPS overload!." + ::= 21 + + dupsNoLongerOverload TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: Recovered from UPS overload." + ::= 22 + + dupsOutputOverCurrent TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: The UPS output overcurrent." + ::= 23 + + dupsNoLongerOutputOverCurrent TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: Recovered from UPS overcurrent." + ::= 24 + + dupsInverterAbnormal TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: The UPS inverter abnormal." + ::= 25 + + dupsInverterRecovered TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: Recovered from UPS inverter abnormal." + ::= 26 + + dupsRectifierAbnormal TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: The UPS rectifier abnormal." + ::= 27 + + dupsRectifierRecovered TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The UPS recovered from rectifier abnormal." + ::= 28 + + dupsReserveAbnormal TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: The UPS rectifier abnormal." + ::= 29 + + dupsReserveRecovered TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The UPS rectifier abnormal." + ::= 30 + + dupsLoadOnReserve TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: The UPS load on reserve." + ::= 31 + + dupsNoLongerLoadOnReserve TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The UPS no longer load on reserve." + ::= 32 + + dupsEnvOverTemperature TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "WARNING: The environment overtemperature." + ::= 33 + + dupsNoLongerEnvOverTemperature TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The environment recovered from overtemperature." + ::= 34 + + dupsEnvOverHumidity TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "WARNING: The environment overhumidity." + ::= 35 + + dupsNoLongerEnvOverHumidity TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The environment recovered from overhumidity." + ::= 36 + + dupsEnvRelay1Alarm TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The environment relay1 is not in normal state." + ::= 37 + + dupsEnvRelay1Normal TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The environment relay1 is in normal state." + ::= 38 + + dupsEnvRelay2Alarm TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The environment relay2 is not in normal state." + ::= 39 + + dupsEnvRelay2Normal TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The environment relay2 is in normal state." + ::= 40 + + dupsEnvRelay3Alarm TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The environment relay3 is not in normal state." + ::= 41 + + dupsEnvRelay3Normal TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The environment relay3 is in normal state." + ::= 42 + + dupsEnvRelay4Alarm TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The environment relay4 is not in normal state." + ::= 43 + + dupsEnvRelay4Normal TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The environment relay4 is in normal state." + ::= 44 + + dupsSmartShutdown TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: Smart Shutdown is initiated." + ::= 45 + + dupsCancelShutdown TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: Cancel UPS Shutdown." + ::= 46 + + dupsTestCompleted TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: This trap is sent upon completion of a UPS diagnostic test." + ::= 47 + + dupsEPOON TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: This trap is sent when emergency power off is on." + ::= 48 + + dupsEPOOFF TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: This trap is sent when UPS recover from emergency power off." + ::= 49 + + dupsOverTemperature TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "SEVER: This trap is sent when the UPS is over heat." + ::= 50 + + dupsNormalTemperature TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: This trap is sent when UPS recover from over heat." + ::= 51 + + dupsBattReplace TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "WARNING: The battery needs to be replaced." + ::= 52 + + dupsReturnFromBattReplace TRAP-TYPE + ENTERPRISE dupsTraps + DESCRIPTION + "INFORMATION: The UPS recovered from battery replacement." + ::= 53 +END |