diff options
Diffstat (limited to 'MIBS/cisco/CISCO-STACKWISE-MIB')
| -rw-r--r-- | MIBS/cisco/CISCO-STACKWISE-MIB | 1842 |
1 files changed, 1842 insertions, 0 deletions
diff --git a/MIBS/cisco/CISCO-STACKWISE-MIB b/MIBS/cisco/CISCO-STACKWISE-MIB new file mode 100644 index 0000000..3a69795 --- /dev/null +++ b/MIBS/cisco/CISCO-STACKWISE-MIB @@ -0,0 +1,1842 @@ +-- ******************************************************************* +-- CISCO-STACKWISE-MIB.my: Cisco StackWise MIB +-- +-- Description of managed objects for the StackWise technology. +-- +-- October 2005, Gunnar Lovblom +-- +-- Copyright (c) 2005, 2008-2012,2016 by Cisco Systems, Inc. +-- All rights reserved. +-- ****************************************************************** + +CISCO-STACKWISE-MIB DEFINITIONS ::= BEGIN + +IMPORTS + Unsigned32, + MODULE-IDENTITY, + NOTIFICATION-TYPE, + OBJECT-TYPE + FROM SNMPv2-SMI + NOTIFICATION-GROUP, + MODULE-COMPLIANCE, + OBJECT-GROUP + FROM SNMPv2-CONF + entPhysicalIndex + FROM ENTITY-MIB + ifIndex + FROM IF-MIB + TruthValue, + MacAddress, + TEXTUAL-CONVENTION + FROM SNMPv2-TC + SnmpAdminString + FROM SNMP-FRAMEWORK-MIB + EntPhysicalIndexOrZero + FROM CISCO-TC + ciscoMgmt + FROM CISCO-SMI; + +ciscoStackWiseMIB MODULE-IDENTITY + LAST-UPDATED "201604160000Z" + ORGANIZATION "Cisco Systems, Inc." + CONTACT-INFO + "Cisco Systems + Customer Service + + Postal: 170 W Tasman Drive + San Jose, CA 95134 + + Tel: +1 800 553-NETS + + E-mail: cs-dsbu@cisco.com" + DESCRIPTION + "This MIB module contain a collection of managed objects + that apply to network devices supporting the Cisco + StackWise(TM) technology. + + The StackWise technology provides a method for collectively + utilizing a stack of switches to create a single switching + unit. + + The data stack is used for switching data packets and, in + power stack, switches are connected by special stack power + cables to share power. Moreover, stackwise is the concept + for combining multiple systems to give an impression of a + single system so that is why both power stack and data stack + are supported by single MIB. + + Terminology: + Stack - A collection of switches connected by the + Cisco StackWise technology. + + Master - The switch that is managing the stack. + + Member - A switch in the stack that is + NOT the stack master. + + Ring - Components that makes up the connections + between the switches in order to create a + stack. + + Stackport - A special physical connector used by the ring. + It is possible for a switch have more than + one stackport. + + SDM - Switch Database Management. + + Stack Power - A collection of switches connected by special + stack power cables to share the power of + inter-connected power supplies across all switches + requiring power. Stack Power is managed by a + single data stack. + + Jack-Jack - It is a device that provides the Power Shelf + capabilities required for Stack Power on + the high-end. + + POE - Power Over Ethernet + + FEP - Front End Power Supply + + SOC - Sustained Overload Condition + + GLS - Graceful Load Shedding + + ILS - Immediate Load Shedding + + SRLS - System Ring Load Shedding + + SSLS - System Star Load Shedding" + REVISION "201604160000Z" + DESCRIPTION + "Added following objects in cswGlobals + - cswStackDomainNum + - cswStackType + - cswStackBandWidth + Created following tables + - cswDistrStackLinkInfoTable + -cswDistrStackPhyPortInfoTable + Added cswStatusGroupRev2 + Deprecated cswStatusGroupRev1 + Added cswDistrStackLinkStatusGroup + Added cswDistrStackPhyPortStatusGroup + Added cswStackWiseMIBComplianceRev4 MIB COMPLIANCE + Deprecated cswStackWiseMIBComplianceRev3 MIB COMPLIANCE." + REVISION "201511240000Z" + DESCRIPTION + "Added following Objects in cswSwitchInfoTable + - cswSwitchPowerAllocated + Added following OBJECT-GROUP + - cswStackPowerAllocatedGroup + Deprecated cswStackWiseMIBComplianceRev2 MODULE-COMPLIANCE. + Added cswStackWiseMIBComplianceRev3 MODULE-COMPLIANCE." + REVISION "201112120000Z" + DESCRIPTION + "Modified 'cswSwitchRole' object." + REVISION "201002010000Z" + DESCRIPTION + "Added cswStackPowerStatusGroup, cswStackPowerSwitchStatusGroup, + cswStackPowerPortStatusGroup, cswStatusGroupRev1 and + cswStackPowerNotificationGroup. + Deprecated cswStackWiseMIBCompliance compliance statement. + Added cswStackWiseMIBComplianceRev1 compliance statement. + Deprecated cswStatusGroup because we deprecated + cswEnableStackNotifications" + REVISION "200806100000Z" + DESCRIPTION + "Modified 'cswSwitchState' object." + REVISION "200510120000Z" + DESCRIPTION + "Initial version of this MIB module." + ::= { ciscoMgmt 500 } + +CswPowerStackMode ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "This textual convention is used to describe the mode of the + power stack. Since the power stack could only run in either + power sharing or redundant mode so this TC will also have only + following valid values, + powerSharing(1) :When a power stack is running in power + sharing mode then all the power supplies + in the power stack contributes towards + the global power budget of the stack. + + redundant(2) :If the user wants the power stack to run + in redundant mode then we will take the + capacity of the largest power supply in + the power stack out of power stack global + power budget pool. + + powerSharingStrict(3):This mode is same as power sharing mode + but, in this mode, the available power + will always be more than the used power. + + redundantStrict(4) :This mode is same as redundant mode but, + in this mode, the available power will + always be more than the used power." + SYNTAX INTEGER { + powerSharing(1), + redundant(2), + powerSharingStrict(3), + redundantStrict(4) + } + +CswPowerStackType ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "This textual conventions is used to describe the type of the + power stack. Since the power stack could only be configured in + a ring or star topology so this TC will have only following + valid values, + ring(1): The power stack has been formed by connecting + the switches in ring topology. + star(2): The power stack has been formed by connecting + the switches in star topology." + SYNTAX INTEGER { + ring(1), + star(2) + } +ciscoStackWiseMIBNotifs OBJECT IDENTIFIER + ::= { ciscoStackWiseMIB 0 } + +ciscoStackWiseMIBObjects OBJECT IDENTIFIER + ::= { ciscoStackWiseMIB 1 } + +ciscoStackWiseMIBConform OBJECT IDENTIFIER + ::= { ciscoStackWiseMIB 2 } + +cswGlobals OBJECT IDENTIFIER + ::= { ciscoStackWiseMIBObjects 1 } + +cswStackInfo OBJECT IDENTIFIER + ::= { ciscoStackWiseMIBObjects 2 } + +cswStackPowerInfo OBJECT IDENTIFIER + ::= { ciscoStackWiseMIBObjects 3 } + +-- Textual Conventions + +CswSwitchNumber ::= TEXTUAL-CONVENTION + DISPLAY-HINT "d" + STATUS current + DESCRIPTION + "A unique value, greater than zero, for each switch in a group + of stackable switches." + SYNTAX Unsigned32 (1..4294967295) + +CswSwitchNumberOrZero ::= TEXTUAL-CONVENTION + DISPLAY-HINT "d" + STATUS current + DESCRIPTION + "A unique value, greater than or equal to zero, for each switch + in a group of stackable switches. + + A value of zero means that the switch number can not be + determined. The value of zero is not unique." + SYNTAX Unsigned32 (0..4294967295) + +CswSwitchPriority ::= TEXTUAL-CONVENTION + DISPLAY-HINT "d" + STATUS current + DESCRIPTION + "A value, greater than or equal to zero, that defines the + priority of a switch in a group of stackable switches. The + higher the value, the higher the priority." + SYNTAX Unsigned32 (0..4294967295) + +-- Global objects pertinent to all switches + +cswMaxSwitchNum OBJECT-TYPE + SYNTAX CswSwitchNumber + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The maximum number of switches that can be configured on + this stack. This is also the maximum value that can be + set by the cswSwitchNumNextReload object." + ::= { cswGlobals 1 } + +cswMaxSwitchConfigPriority OBJECT-TYPE + SYNTAX CswSwitchPriority + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The maximum configurable priority for a switch in this stack. + Highest value equals highest priority. This is the highest + value that can be set by the cswSwitchSwPriority object." + ::= { cswGlobals 2 } + +cswRingRedundant OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A value of 'true' is returned when the stackports are + connected in such a way that it forms a redundant ring." + ::= { cswGlobals 3 } + +cswStackPowerInfoTable OBJECT-TYPE + SYNTAX SEQUENCE OF CswStackPowerInfoEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table holds the information about all the power stacks in + a single data stack." + ::= { cswStackPowerInfo 1 } + +cswStackPowerInfoEntry OBJECT-TYPE + SYNTAX CswStackPowerInfoEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in the cswStackPowerInfoTable for each of the power + stacks in a single data stack. This entry contains information + regarding the power stack." + INDEX { cswStackPowerStackNumber } + ::= { cswStackPowerInfoTable 1 } + +CswStackPowerInfoEntry ::= SEQUENCE { + cswStackPowerStackNumber Unsigned32, + cswStackPowerMode CswPowerStackMode, + cswStackPowerMasterMacAddress MacAddress, + cswStackPowerMasterSwitchNum Unsigned32, + cswStackPowerNumMembers Unsigned32, + cswStackPowerType CswPowerStackType, + cswStackPowerName SnmpAdminString +} + +cswStackPowerStackNumber OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A unique value, greater than zero, to identify a power stack." + ::= { cswStackPowerInfoEntry 1 } + +cswStackPowerMode OBJECT-TYPE + SYNTAX CswPowerStackMode + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This object specifies the information about the mode of the + power stack. + Power-sharing mode: All of the input power can be used for + loads, and the total available power appears as one huge power + supply. The power budget includes all power from all supplies. + No power is set aside for power supply failures, so if a power + supply fails, load shedding (shutting down of powered devices or + switches) might occur. This is the default. + Redundant mode: The largest power supply is removed from the + power pool to be used as backup power in case one of the other + power supplies fails. The available power budget is the total + power minus the largest power supply. This reduces the available + power in the pool for switches and powered devices to draw from, + but in case of a failure or an extreme power load, there is less + chance of having to shut down switches or powered devices. This + is the recommended operating mode if your system has enough + power. + In addition, you can configure each mode to run a strict power + budget or a non-strict (loose) power budget. If the mode is + strict, the stack power needs cannot exceed the available power. + When the power budgeted to devices reaches the maximum available + PoE power, power is denied to the next device seeking power. In + this mode the stack never goes into an over-budgeted power mode. + When the mode is non-strict, budgeted power is allowed to exceed + available power. This is normally not a problem because most + devices do not run at full power and the chances of all powered + devices in the stack requiring maximum power at the same time is + small." + ::= { cswStackPowerInfoEntry 2 } + +cswStackPowerMasterMacAddress OBJECT-TYPE + SYNTAX MacAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates the Mac address of the power stack + master." + ::= { cswStackPowerInfoEntry 3 } + +cswStackPowerMasterSwitchNum OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates the switch number of the power stack + master. + The value of this object would be zero if the power stack + master is not part of this data stack." + ::= { cswStackPowerInfoEntry 4 } + +cswStackPowerNumMembers OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates the number of members in the power + stack." + ::= { cswStackPowerInfoEntry 5 } + +cswStackPowerType OBJECT-TYPE + SYNTAX CswPowerStackType + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates the topology of the power stack, that is, + whether the switch is running in RING or STAR topology." + ::= { cswStackPowerInfoEntry 6 } + +cswStackPowerName OBJECT-TYPE + SYNTAX SnmpAdminString + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This object specifies a unique name of this power stack. A + zero-length string indicates no name is assigned." + ::= { cswStackPowerInfoEntry 7 } + + +cswStackPowerPortInfoTable OBJECT-TYPE + SYNTAX SEQUENCE OF CswStackPowerPortInfoEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table contains information about the stack power ports. + There exists an entry in this table for each physical stack + power port." + ::= { cswStackPowerInfo 2 } + +cswStackPowerPortInfoEntry OBJECT-TYPE + SYNTAX CswStackPowerPortInfoEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row in the cswStackPowerPortInfoTable. This entry + contains information about a power stack port." + INDEX { + entPhysicalIndex, + cswStackPowerPortIndex + } + ::= { cswStackPowerPortInfoTable 1 } + +CswStackPowerPortInfoEntry ::= SEQUENCE { + cswStackPowerPortIndex Unsigned32, + cswStackPowerPortOperStatus INTEGER, + cswStackPowerPortNeighborMacAddress MacAddress, + cswStackPowerPortNeighborSwitchNum CswSwitchNumberOrZero, + cswStackPowerPortLinkStatus INTEGER, + cswStackPowerPortOverCurrentThreshold Unsigned32, + cswStackPowerPortName SnmpAdminString +} + +cswStackPowerPortIndex OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A unique value, greater than zero, for each stack power port." + ::= { cswStackPowerPortInfoEntry 1 } + +cswStackPowerPortOperStatus OBJECT-TYPE + SYNTAX INTEGER { + enabled(1), + disabled(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This object is used to either set or unset the operational + status of the stack port. This object will have following valid + values, + + enabled(1) : The port is enabled + disabled(2) : The port is forced down" + ::= { cswStackPowerPortInfoEntry 2 } + +cswStackPowerPortNeighborMacAddress OBJECT-TYPE + SYNTAX MacAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This objects indicates the port neighbor's Mac Address." + ::= { cswStackPowerPortInfoEntry 3 } + +cswStackPowerPortNeighborSwitchNum OBJECT-TYPE + SYNTAX CswSwitchNumberOrZero + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This objects indicates the port neighbor's switch number. If + either there is no switch connected or the neighbor is not + Jack-Jack then the value of this object is going to be 0." + ::= { cswStackPowerPortInfoEntry 4 } + +cswStackPowerPortLinkStatus OBJECT-TYPE + SYNTAX INTEGER { + up(1), + down(2) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object is used to describe the link status of the stack + port. This object will have following valid + values, + + up(1) : The port is connected and operational + down(2): The port is either forced down or not connected" + ::= { cswStackPowerPortInfoEntry 5 } + +cswStackPowerPortOverCurrentThreshold OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "Amperes" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This object is used to retrieve the over current threshold. The + stack power cables are limited to carry current up to the limit + retrieved by this object. The stack power cables would not be + able to function properly if either the input or output current + goes beyond the threshold retrieved by this object." + ::= { cswStackPowerPortInfoEntry 6 } + +cswStackPowerPortName OBJECT-TYPE + SYNTAX SnmpAdminString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object specifies a unique name of the stack power port as + shown on the face plate of the system. A zero-length string + indicates no name is assigned." + ::= { cswStackPowerPortInfoEntry 7 } + + +cswEnableStackNotifications OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS deprecated + DESCRIPTION + "This object indicates whether the system generates the + notifications defined in this MIB or not. A value of + 'false' will prevent the notifications from being sent." + ::= { cswGlobals 4 } + +cswEnableIndividualStackNotifications OBJECT-TYPE + SYNTAX BITS { + stackPortChange(0), + stackNewMaster(1), + stackMismatch(2), + stackRingRedundant(3), + stackNewMember(4), + stackMemberRemoved(5), + stackPowerLinkStatusChanged(6), + stackPowerPortOperStatusChanged(7), + stackPowerVersionMismatch(8), + stackPowerInvalidTopology(9), + stackPowerBudgetWarning(10), + stackPowerInvalidInputCurrent(11), + stackPowerInvalidOutputCurrent(12), + stackPowerUnderBudget(13), + stackPowerUnbalancedPowerSupplies(14), + stackPowerInsufficientPower(15), + stackPowerPriorityConflict(16), + stackPowerUnderVoltage(17), + stackPowerGLS(18), + stackPowerILS(19), + stackPowerSRLS(20), + stackPowerSSLS(21), + stackMemberToBeReloadedForUpgrade(22) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This object is used to enable/disable individual notifications + defined in this MIB module. Turning on a particular bit would + enable the corresponding trap and, similarly, turning off a + particular bit would disable the corresponding trap. The + following notifications are controlled by this object: + + stackPortChange(0): enables/disables cswStackPortChange + notification. + + stackNewMaster(1): enables/disables cswStackNewMember + notification. + + stackMismatch(2): enables/disables cswStackMismatch + notification. + + stackRingRedundant(3): enables/disables cswStackRingRedundant + notification. + + stackNewMember(4): enables/disables cswStackNewMember + notification. + + stackMemberRemoved(5): enables/disables cswStackMemberRemoved + notification. + + stackPowerLinkStatusChanged(6): enables/disables + cswStackPowerPortLinkStatusChanged notification. + + stackPowerPortOperStatusChanged(7): enables/disables + cswStackPowerPortOperStatusChanged notification. + + stackPowerVersionMismatch(8): enables/disables + cswStackPowerVersionMismatch notification. + + stackPowerInvalidTopology(9): enables/disables + cswStackPowerInvalidTopology notification + + stackPowerBudgetWarning(10): enables/disables + cswStackPowerBudgetWarning notification. + + stackPowerInvalidInputCurrent(11): enables/disables + cswStackPowerInvalidInputCurrent notification. + + stackPowerInvalidOutputCurrent(12): enables/disables + cswStackPowerInvalidOutputCurrent notification. + + stackPowerUnderBudget(13): enables/disables + cswStackPowerUnderBudget notification. + + stackPowerUnbalancedPowerSupplies(14): enables/disables + cswStackPowerUnbalancedPowerSupplies notification. + + stackPowerInsufficientPower(15): enables/disables + cswStackPowerInsufficientPower notification. + + stackPowerPriorityConflict(16): enables/disables + cswStackPowerPriorityConflict notification. + + stackPowerUnderVoltage(17): enables/disables + cswStackPowerUnderVoltage notification. + + stackPowerGLS(18): enables/disables cswStackPowerGLS + notification. + + stackPowerILS(19): enables/disabled cswStackPowerILS + notification. + + stackPowerSRLS(20): enables/disables cswStackPowerSRLS + notification. + + stackPowerSSLS(21): enables/disables cswStackPowerSSLS + notification. + stackMemberToBeReloadedForUpgrade(22): enables/disables + cswStackMemberToBeReloadedForUpgrade notification." + ::= { cswGlobals 5 } + +cswStackDomainNum OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates distributed domain of the switch.Only + Switches with the same domain number can be in the same dist + ributed domain.0 means no switch domain configured." + ::= { cswGlobals 6 } + +cswStackType OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates type of switch stack. value + of Switch virtual domain determines if switch is + distributed or conventional stack. 0 means stack + is conventional back side stack." + ::= { cswGlobals 7 } + +cswStackBandWidth OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates stack bandwidth." + ::= { cswGlobals 8 } + +-- Switch Information Table + +cswSwitchInfoTable OBJECT-TYPE + SYNTAX SEQUENCE OF CswSwitchInfoEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table contains information specific to switches in a + stack. Every switch with an entry in the entPhysicalTable + (ENTITY-MIB) whose entPhysicalClass is 'chassis' will have + an entry in this table." + ::= { cswStackInfo 1 } + +cswSwitchInfoEntry OBJECT-TYPE + SYNTAX CswSwitchInfoEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row in the cswSwitchInfoTable describing + a switch information." + INDEX { entPhysicalIndex } + ::= { cswSwitchInfoTable 1 } + +CswSwitchInfoEntry ::= SEQUENCE { + cswSwitchNumCurrent CswSwitchNumber, + cswSwitchNumNextReload CswSwitchNumberOrZero, + cswSwitchRole INTEGER, + cswSwitchSwPriority CswSwitchPriority, + cswSwitchHwPriority CswSwitchPriority, + cswSwitchState INTEGER, + cswSwitchMacAddress MacAddress, + cswSwitchSoftwareImage SnmpAdminString, + cswSwitchPowerBudget Unsigned32, + cswSwitchPowerCommited Unsigned32, + cswSwitchSystemPowerPriority Unsigned32, + cswSwitchPoeDevicesLowPriority Unsigned32, + cswSwitchPoeDevicesHighPriority Unsigned32, + cswSwitchPowerAllocated Unsigned32 +} + +cswSwitchNumCurrent OBJECT-TYPE + SYNTAX CswSwitchNumber + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object contains the current switch identification number. + This number should match any logical labeling on the switch. + For example, a switch whose interfaces are labeled + 'interface #3' this value should be 3." + ::= { cswSwitchInfoEntry 1 } + +cswSwitchNumNextReload OBJECT-TYPE + SYNTAX CswSwitchNumberOrZero + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This object contains the cswSwitchNumCurrent to be + used at next reload. The maximum value for this object is + defined by the cswMaxSwitchNum object. + + Note: This object will contain 0 and cannot be set if the + cswSwitchState value is other than 'ready'." + ::= { cswSwitchInfoEntry 2 } + +cswSwitchRole OBJECT-TYPE + SYNTAX INTEGER { + master(1), + member(2), + notMember(3), + standby(4) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object describes the function of the switch: + + master - stack master. + + member - active member of the stack. + + notMember - none-active stack member, see + cswSwitchState for status. + + standby - stack standby switch." + ::= { cswSwitchInfoEntry 3 } + +cswSwitchSwPriority OBJECT-TYPE + SYNTAX CswSwitchPriority + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "A number containing the priority of a switch. The switch with + the highest priority will become the master. The maximum value + for this object is defined by the cswMaxSwitchConfigPriority + object. + + If after a reload the value of cswMaxSwitchConfigPriority + changes to a smaller value, and the value of cswSwitchSwPriority + has been previously set to a value greater or equal to the + new cswMaxSwitchConfigPriority, then the SNMP agent must set + cswSwitchSwPriority to the new cswMaxSwitchConfigPriority. + + Note: This object will contain the value of 0 if the + cswSwitchState value is other than 'ready'." + ::= { cswSwitchInfoEntry 4 } + +cswSwitchHwPriority OBJECT-TYPE + SYNTAX CswSwitchPriority + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object contains the hardware priority of a switch. If + two or more entries in this table have the same + cswSwitchSwPriority value during the master election time, + the switch with the highest cswSwitchHwPriority will become + the master. + + Note: This object will contain the value of 0 if the + cswSwitchState value is other than 'ready'." + ::= { cswSwitchInfoEntry 5 } + +cswSwitchState OBJECT-TYPE + SYNTAX INTEGER { + waiting(1), + progressing(2), + added(3), + ready(4), + sdmMismatch(5), + verMismatch(6), + featureMismatch(7), + newMasterInit(8), + provisioned(9), + invalid(10), + removed(11) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The current state of a switch: + + waiting - Waiting for a limited time on other + switches in the stack to come online. + + progressing - Master election or mismatch checks in + progress. + + added - The switch is added to the stack. + + ready - The switch is operational. + + sdmMismatch - The SDM template configured on the master + is not supported by the new member. + + verMismatch - The operating system version running on the + master is different from the operating + system version running on this member. + + featureMismatch - Some of the features configured on the + master are not supported on this member. + + newMasterInit - Waiting for the new master to finish + initialization after master switchover + (Master Re-Init). + + provisioned - The switch is not an active member of the + stack. + + invalid - The switch's state machine is in an + invalid state. + + removed - The switch is removed from the stack." + ::= { cswSwitchInfoEntry 6 } + +cswSwitchMacAddress OBJECT-TYPE + SYNTAX MacAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The MAC address of the switch. + + Note: This object will contain the value of 0000:0000:0000 + if the cswSwitchState value is other than 'ready'." + ::= { cswSwitchInfoEntry 7 } + +cswSwitchSoftwareImage OBJECT-TYPE + SYNTAX SnmpAdminString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The software image type running on the switch. + + Note: This object will contain an empty string if the + cswSwitchState value is other than 'ready'." + ::= { cswSwitchInfoEntry 8 } + +cswSwitchPowerBudget OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "Watts" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates the power budget of the switch." + ::= { cswSwitchInfoEntry 9 } + +cswSwitchPowerCommited OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "Watts" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates the power committed to the POE devices + connected to the switch." + ::= { cswSwitchInfoEntry 10 } + +cswSwitchSystemPowerPriority OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This specifies the system's power priority. In case of + a power failure then the system with the highest system + priority will be brought down last." + ::= { cswSwitchInfoEntry 11 } + +cswSwitchPoeDevicesLowPriority OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This object specifies the priority of the system's low + priority POE devices." + ::= { cswSwitchInfoEntry 12 } + +cswSwitchPoeDevicesHighPriority OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This object specifies the priority of the system's high + priority POE devices. In order to avoid losing the high + priority POE devices before the low priority POE devices, + this object's value must be greater than value of + cswSwitchPoeDevicesLowPriority." + ::= { cswSwitchInfoEntry 13 } + +cswSwitchPowerAllocated OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "Watts" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates the power committed to the POE devices + connected to the switch." + ::= { cswSwitchInfoEntry 14 } + +-- StackPort Information Table + +cswStackPortInfoTable OBJECT-TYPE + SYNTAX SEQUENCE OF CswStackPortInfoEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table contains stackport specific information. There + exists an entry in this table for every physical stack + port that have an entry in the ifTable (IF-MIB)." + ::= { cswStackInfo 2 } + +cswStackPortInfoEntry OBJECT-TYPE + SYNTAX CswStackPortInfoEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row in the cswStackPortInfoTable. An entry + contains information about a stackport." + INDEX { ifIndex } + ::= { cswStackPortInfoTable 1 } + +CswStackPortInfoEntry ::= SEQUENCE { + cswStackPortOperStatus INTEGER, + cswStackPortNeighbor EntPhysicalIndexOrZero +} + +cswStackPortOperStatus OBJECT-TYPE + SYNTAX INTEGER { + up(1), + down(2), + forcedDown(3) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The state of the stackport. + + up - Connected and operational. + + down - Not connected to a neighboring switch or + administrative down. + + forcedDown - Shut down by stack manager due to mismatch or + stackport errors." + ::= { cswStackPortInfoEntry 1 } + +cswStackPortNeighbor OBJECT-TYPE + SYNTAX EntPhysicalIndexOrZero + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object contains the value of the entPhysicalIndex of the + switch's chassis to which this stackport is connected to. If + the stackport is not connected, the value 0 is returned." + ::= { cswStackPortInfoEntry 2 } + +-- Distributed Stack Link Information Table + +cswDistrStackLinkInfoTable OBJECT-TYPE + SYNTAX SEQUENCE OF CswDistrStackLinkInfoEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Distributed Stack Link Information." + ::= { cswStackInfo 3 } + +cswDistrStackLinkInfoEntry OBJECT-TYPE + SYNTAX CswDistrStackLinkInfoEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An Entry containing information about DSL link." + INDEX { entPhysicalIndex , + cswDSLindex } + ::= { cswDistrStackLinkInfoTable 1 } + +CswDistrStackLinkInfoEntry ::= SEQUENCE { + cswDSLindex Unsigned32, + cswDistrStackLinkBundleOperStatus INTEGER + +} + +cswDSLindex OBJECT-TYPE + SYNTAX Unsigned32 (1..2) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This is index of the distributed stack link + with respect to each interface port" + ::= { cswDistrStackLinkInfoEntry 1 } + +cswDistrStackLinkBundleOperStatus OBJECT-TYPE + SYNTAX INTEGER { + up(1), + down(2) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The state of the stackLink. + up - Connected and operational. + down - Not connected or administrative down." + ::= { cswDistrStackLinkInfoEntry 2 } + +-- Distributed Stack Port Information Table + +cswDistrStackPhyPortInfoTable OBJECT-TYPE + SYNTAX SEQUENCE OF CswDistrStackPhyPortInfoEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table contains objects for Distributed stack + Link information Table." + ::= { cswStackInfo 4 } + +cswDistrStackPhyPortInfoEntry OBJECT-TYPE + SYNTAX CswDistrStackPhyPortInfoEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An Entry containing information about stack port that + is part of Distributed Stack Link." + INDEX { entPhysicalIndex, + cswDSLindex, + ifIndex + } + ::= { cswDistrStackPhyPortInfoTable 1 } + +CswDistrStackPhyPortInfoEntry ::= SEQUENCE { + cswDistrStackPhyPort SnmpAdminString, + cswDistrStackPhyPortOperStatus INTEGER, + cswDistrStackPhyPortNbr SnmpAdminString, + cswDistrStackPhyPortNbrsw EntPhysicalIndexOrZero + +} + +cswDistrStackPhyPort OBJECT-TYPE + SYNTAX SnmpAdminString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates the name of distributed stack port." + ::= { cswDistrStackPhyPortInfoEntry 1 } + +cswDistrStackPhyPortOperStatus OBJECT-TYPE + SYNTAX INTEGER { + up(1), + down(2) + + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The state of the distributed stackport. + up - Connected and operational. + down - Not connected to a neighboring switch or + administrative down." + ::= { cswDistrStackPhyPortInfoEntry 2 } + +cswDistrStackPhyPortNbr OBJECT-TYPE + SYNTAX SnmpAdminString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates the name of + distributed stack port's neighbor." + ::= { cswDistrStackPhyPortInfoEntry 3 } + +cswDistrStackPhyPortNbrsw OBJECT-TYPE + SYNTAX EntPhysicalIndexOrZero + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates the EntPhysicalIndex of + the distributed stack port's neigbor switch." + ::= { cswDistrStackPhyPortInfoEntry 4 } + +-- Notifications + +cswMIBNotifications OBJECT IDENTIFIER + ::= { ciscoStackWiseMIBNotifs 0 } + +cswStackPortChange NOTIFICATION-TYPE + OBJECTS { + ifIndex, + cswStackPortOperStatus, + cswSwitchNumCurrent + } + STATUS current + DESCRIPTION + "This notification is generated when the state + of a stack port has changed." + ::= { cswMIBNotifications 1 } + +cswStackNewMaster NOTIFICATION-TYPE + OBJECTS { cswSwitchNumCurrent } + STATUS current + DESCRIPTION + "This notification is generated when a new master has been + elected. The notification will contain the cswSwitchNumCurrent + object to indicate the new master ID." + ::= { cswMIBNotifications 2 } + +cswStackMismatch NOTIFICATION-TYPE + OBJECTS { + cswSwitchState, + cswSwitchNumCurrent + } + STATUS current + DESCRIPTION + "This notification is generated when a new member attempt + to join the stack but was denied due to a mismatch. The + cswSwitchState object will indicate the type of mismatch." + ::= { cswMIBNotifications 3 } + +cswStackRingRedundant NOTIFICATION-TYPE + OBJECTS { cswRingRedundant } + STATUS current + DESCRIPTION + "This notification is generated when the redundancy of the + ring has changed." + ::= { cswMIBNotifications 4 } + +cswStackNewMember NOTIFICATION-TYPE + OBJECTS { cswSwitchNumCurrent } + STATUS current + DESCRIPTION + "This notification is generated when a new member joins the + stack." + ::= { cswMIBNotifications 5 } + +cswStackMemberRemoved NOTIFICATION-TYPE + OBJECTS { cswSwitchNumCurrent } + STATUS current + DESCRIPTION + "This notification is generated when a member is removed + from the stack." + ::= { cswMIBNotifications 6 } + +cswStackPowerPortLinkStatusChanged NOTIFICATION-TYPE + OBJECTS { + cswStackPowerPortLinkStatus, + cswSwitchNumCurrent, + cswStackPowerPortName + } + STATUS current + DESCRIPTION + "This notification is generated when the link status of a stack + power port is changed from up to down or down to up. This + notification is for informational purposes only and no action + is required. cswStackPowerPortLinkStatus indicates link status + of the stack power ports. cswSwitchNumCurrent indicates the + switch number of the system. cswStackPowerPortName specifies a + unique name of the stack power port as shown on the face plate + of the system." + ::= { cswMIBNotifications 7 } + +cswStackPowerPortOperStatusChanged NOTIFICATION-TYPE + OBJECTS { + cswSwitchNumCurrent, + cswStackPowerPortOperStatus, + cswStackPowerPortName + } + STATUS current + DESCRIPTION + "This notification is generated when the operational status of a + stack power port is changed from enabled to disabled or from + disabled to enabled. This notification is for informational + purposes only and no action is required. cswSwitchNumCurrent + indicates the switch number of the system. + cswStackPowerPortOperStatus indicates operational status + of the stack power ports. cswStackPowerPortName specifies + a unique name of the stack power port as shown on the face + plate of the system." + ::= { cswMIBNotifications 8 } + +cswStackPowerVersionMismatch NOTIFICATION-TYPE + OBJECTS { cswSwitchNumCurrent } + STATUS current + DESCRIPTION + "This notification is generated when the major version of the + stack power protocol is different from the other members of the + power stack. Upon receiving this notification, the user should + make sure that he/she is using the same software version on all + the members of the same power stack. cswSwitchNumCurrent + indicates the switch number of the system seeing the power + stack version mismatch." + ::= { cswMIBNotifications 9 } + +cswStackPowerInvalidTopology NOTIFICATION-TYPE + OBJECTS { cswSwitchNumCurrent } + STATUS current + DESCRIPTION + "This notification is generated when an invalid stack power + topology is discovered by a switch. cswSwitchNumCurrent + indicates the switch number of the system where the invalid + topology is discovered." + ::= { cswMIBNotifications 10 } + +cscwStackPowerBudgetWarrning NOTIFICATION-TYPE + OBJECTS { cswSwitchNumCurrent } + STATUS current + DESCRIPTION + "This notification is generated when the switch power budget is + more than 1000W above its power supplies rated power output. + cswSwitchNumCurrent indicates the switch number of the system + where the invalid power budget has been detected." + ::= { cswMIBNotifications 11 } + +cswStackPowerInvalidInputCurrent NOTIFICATION-TYPE + OBJECTS { + cswSwitchNumCurrent, + cswStackPowerPortOverCurrentThreshold, + cswStackPowerPortName + } + STATUS current + DESCRIPTION + "This notification is generated when the input current in the + stack power cable is over the limit of the threshold retrieved + by the agent through cswStackPowerPortOverCurrentThreshold + object. Upon receiving this notification, the user should add a + power supply to the system whose switch number is generated + with this notification. cswSwitchNumCurrent + indicates the switch number of the system. + cswStackPowerPortOverCurrentThreshold indicates the over current + threshold of power stack cables. cswStackPowerPortName specifies + a unique name of the stack power port as shown on the face + plate of the system." + ::= { cswMIBNotifications 12 } + +cswStackPowerInvalidOutputCurrent NOTIFICATION-TYPE + OBJECTS { + cswSwitchNumCurrent, + cswStackPowerPortOverCurrentThreshold, + cswStackPowerPortName + } + STATUS current + DESCRIPTION + "This notification is generated when the output current in the + stack power cable is over the limit of the threshold retrieved + by the agent through cswStackPowerPortOverCurrentThreshold + object. Upon receiving this notification, the user should + remove a power supply from the system whose switch number is + generated with this notification. cswSwitchNumCurrent + indicates the switch number of the system. + cswStackPowerPortOverCurrentThreshold indicates the over current + threshold of power stack cables. cswStackPowerPortName specifies + a unique name of the stack power port as shown on the face + plate of the system." + ::= { cswMIBNotifications 13 } + +cswStackPowerUnderBudget NOTIFICATION-TYPE + OBJECTS { cswSwitchNumCurrent } + STATUS current + DESCRIPTION + "This notification is generated when the switch's budget is less + than maximum possible switch power consumption. + cswSwitchNumCurrent indicates the switch number of the system + that is running with the power budget less than the power + consumption." + ::= { cswMIBNotifications 14 } + +cswStackPowerUnbalancedPowerSupplies NOTIFICATION-TYPE + OBJECTS { cswStackPowerName } + STATUS current + DESCRIPTION + "This notification is generated when the switch has no power + supply but another switch in the same stack has more than one + power supplies. cswStackPowerName specifies a unique name of the + power stack where the unbalanced power supplies are detected." + ::= { cswMIBNotifications 15 } + +cswStackPowerInsufficientPower NOTIFICATION-TYPE + OBJECTS { cswStackPowerName } + STATUS current + DESCRIPTION + "This notification is generated when the switch's power stack + does not have enough power to bring up all the switches in the + power stack. cswStackPowerName specifies a unique name of the + power stack where insufficient power condition is detected." + ::= { cswMIBNotifications 16 } + +cswStackPowerPriorityConflict NOTIFICATION-TYPE + OBJECTS { cswStackPowerName } + STATUS current + DESCRIPTION + "This notification is generated when the switch's power + priorities are conflicting with power priorities of another + switch in the same power stack. cswStackPowerPortName specifies + the unique name of the power stack where the conflicting power + priorities are detected." + ::= { cswMIBNotifications 17 } + +cswStackPowerUnderVoltage NOTIFICATION-TYPE + OBJECTS { cswSwitchNumCurrent } + STATUS current + DESCRIPTION + "This notification is generated when the switch had an under + voltage condition on last boot up. cswSwitchNumCurrent + indicates the switch number of the system that was forced + down with the under voltage condition." + ::= { cswMIBNotifications 18 } + +cswStackPowerGLS NOTIFICATION-TYPE + OBJECTS { cswSwitchNumCurrent } + STATUS current + DESCRIPTION + "This notification is generated when the switch had to shed + loads based on a sustained over load (SOC) condition. + cswSwitchNumCurrent indicates the switch number of the system + that goes through graceful load shedding." + ::= { cswMIBNotifications 19 } + +cswStackPowerILS NOTIFICATION-TYPE + OBJECTS { cswSwitchNumCurrent } + STATUS current + DESCRIPTION + "This notification is generated when the switch had to shed + loads based on power supply fail condition. cswSwitchNumCurrent + indicates the switch number of the system that goes through + immediate load shedding." + ::= { cswMIBNotifications 20 } + +cswStackPowerSRLS NOTIFICATION-TYPE + OBJECTS { cswSwitchNumCurrent } + STATUS current + DESCRIPTION + "This notification is generated when the switch had to shed + loads based on loss of a system in ring topology. + cswSwitchNumCurrent indicates the switch number of the system + that detects the loss of system in ring topology." + ::= { cswMIBNotifications 21 } + +cswStackPowerSSLS NOTIFICATION-TYPE + OBJECTS { cswSwitchNumCurrent } + STATUS current + DESCRIPTION + "This notification is generated when the switch had to shed + loads based on loss of a system in star topology. + cswSwitchNumCurrent indicates the switch number of the system + that detects the loss of system in star topology." + ::= { cswMIBNotifications 22 } + +cswStackMemberToBeReloadedForUpgrade NOTIFICATION-TYPE + OBJECTS { cswSwitchNumCurrent } + STATUS current + DESCRIPTION + "This notification is generated when a member is to be reloaded + for upgrade." + ::= { cswMIBNotifications 23 } +-- Conformance and Compliance statements + +cswStackWiseMIBCompliances OBJECT IDENTIFIER + ::= { ciscoStackWiseMIBConform 1 } + +cswStackWiseMIBGroups OBJECT IDENTIFIER + ::= { ciscoStackWiseMIBConform 2 } + +cswStackWiseMIBCompliance MODULE-COMPLIANCE + STATUS deprecated + DESCRIPTION + "The compliance statement for entities that implement the + CISCO-STACKWISE-MIB." + MODULE -- this module + MANDATORY-GROUPS { + cswStatusGroup, + cswNotificationGroup + } + + OBJECT cswSwitchSwPriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswSwitchNumNextReload + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + ::= { cswStackWiseMIBCompliances 1 } + +cswStackWiseMIBComplianceRev1 MODULE-COMPLIANCE + STATUS deprecated + DESCRIPTION + "The compliance statements for entities described in + CISCO-STACKWISE-MIB. Stack Power entities are added in this + revision." + MODULE -- this module + MANDATORY-GROUPS { + cswNotificationGroup, + cswStatusGroupRev1, + cswStackPowerEnableNotificationGroup + } + + GROUP cswStackPowerStatusGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + + GROUP cswStackPowerSwitchStatusGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + + GROUP cswStackPowerPortStatusGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + + GROUP cswStackPowerNotificationGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + ::= { cswStackWiseMIBCompliances 2 } + +cswStackWiseMIBComplianceRev2 MODULE-COMPLIANCE + STATUS deprecated + DESCRIPTION + "The compliance statements for entities described in + CISCO-STACKWISE-MIB. Stack Power entities are added in this + revision." + MODULE -- this module + MANDATORY-GROUPS { + cswNotificationGroup, + cswNotificationGroupSup1, + cswStatusGroupRev1, + cswStackPowerEnableNotificationGroup + } + + GROUP cswStackPowerStatusGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + + GROUP cswStackPowerSwitchStatusGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + + GROUP cswStackPowerPortStatusGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + + GROUP cswStackPowerNotificationGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + ::= { cswStackWiseMIBCompliances 3 } + +cswStackWiseMIBComplianceRev3 MODULE-COMPLIANCE + STATUS deprecated + DESCRIPTION + "The compliance statements for entities described in + CISCO-STACKWISE-MIB. Stack Power entities are added in this + revision." + MODULE -- this module + MANDATORY-GROUPS { + cswNotificationGroup, + cswNotificationGroupSup1, + cswStatusGroupRev1, + cswStackPowerEnableNotificationGroup + } + + GROUP cswStackPowerStatusGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + + GROUP cswStackPowerSwitchStatusGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + + GROUP cswStackPowerPortStatusGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + + GROUP cswStackPowerNotificationGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + + GROUP cswStackPowerAllocatedGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power allocation information." + OBJECT cswStackPowerMode + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswStackPowerName + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswStackPowerPortOperStatus + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswStackPowerPortOverCurrentThreshold + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswEnableIndividualStackNotifications + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswSwitchNumNextReload + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswSwitchSwPriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswSwitchSystemPowerPriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswSwitchPoeDevicesLowPriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswSwitchPoeDevicesHighPriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + ::= { cswStackWiseMIBCompliances 4 } + +cswStackWiseMIBComplianceRev4 MODULE-COMPLIANCE + STATUS current + DESCRIPTION + "The compliance statements for entities described in + CISCO-STACKWISE-MIB. Stack Global entities are added in this + revision." + MODULE -- this module + MANDATORY-GROUPS { + cswNotificationGroup, + cswNotificationGroupSup1, + cswStatusGroupRev2, + cswStackPowerEnableNotificationGroup, + cswDistrStackLinkStatusGroup, + cswDistrStackPhyPortStatusGroup + } + + GROUP cswStackPowerStatusGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + + GROUP cswStackPowerSwitchStatusGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + + GROUP cswStackPowerPortStatusGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + + GROUP cswStackPowerNotificationGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power." + + GROUP cswStackPowerAllocatedGroup + DESCRIPTION + "This group is only mandatory for systems which support stack + power allocation information." + + OBJECT cswStackPowerMode + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswStackPowerName + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswStackPowerPortOperStatus + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswStackPowerPortOverCurrentThreshold + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswEnableIndividualStackNotifications + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswSwitchNumNextReload + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswSwitchSwPriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswSwitchSystemPowerPriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswSwitchPoeDevicesLowPriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT cswSwitchPoeDevicesHighPriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + ::= { cswStackWiseMIBCompliances 5 } + +-- units of conformance + +cswStatusGroup OBJECT-GROUP + OBJECTS { + cswMaxSwitchNum, + cswMaxSwitchConfigPriority, + cswRingRedundant, + cswEnableStackNotifications, + cswSwitchNumCurrent, + cswSwitchNumNextReload, + cswSwitchRole, + cswSwitchSwPriority, + cswSwitchHwPriority, + cswSwitchState, + cswSwitchMacAddress, + cswSwitchSoftwareImage, + cswStackPortOperStatus, + cswStackPortNeighbor, + cswStackPowerType + } + STATUS deprecated + DESCRIPTION + "A collection of objects that are used for control and + status." + ::= { cswStackWiseMIBGroups 1 } + +cswNotificationGroup NOTIFICATION-GROUP + NOTIFICATIONS { + cswStackPortChange, + cswStackNewMaster, + cswStackMismatch, + cswStackRingRedundant, + cswStackNewMember, + cswStackMemberRemoved + } + STATUS current + DESCRIPTION + "A collection of notifications that are required." + ::= { cswStackWiseMIBGroups 2 } + +cswStatusGroupRev1 OBJECT-GROUP + OBJECTS { + cswMaxSwitchNum, + cswMaxSwitchConfigPriority, + cswRingRedundant, + cswSwitchNumCurrent, + cswSwitchNumNextReload, + cswSwitchRole, + cswSwitchSwPriority, + cswSwitchHwPriority, + cswSwitchState, + cswSwitchMacAddress, + cswSwitchSoftwareImage + } + STATUS current + DESCRIPTION + "A collection of objects that are used for control and + status." + ::= { cswStackWiseMIBGroups 3 } + +cswStackPowerStatusGroup OBJECT-GROUP + OBJECTS { + cswStackPowerMode, + cswStackPowerMasterMacAddress, + cswStackPowerMasterSwitchNum, + cswStackPowerNumMembers, + cswStackPowerType, + cswStackPowerName + } + STATUS current + DESCRIPTION + "A collection of stack power objects that are used for control + and status of power stack." + ::= { cswStackWiseMIBGroups 4 } + +cswStackPowerSwitchStatusGroup OBJECT-GROUP + OBJECTS { + cswSwitchPowerBudget, + cswSwitchPowerCommited, + cswSwitchSystemPowerPriority, + cswSwitchPoeDevicesLowPriority, + cswSwitchPoeDevicesHighPriority + } + STATUS current + DESCRIPTION + "A collection of stack power objects that are used to track the + stack power parameters of a switch." + ::= { cswStackWiseMIBGroups 5 } + +cswStackPowerPortStatusGroup OBJECT-GROUP + OBJECTS { + cswStackPowerPortOperStatus, + cswStackPowerPortNeighborMacAddress, + cswStackPowerPortNeighborSwitchNum, + cswStackPowerPortLinkStatus, + cswStackPowerPortOverCurrentThreshold, + cswStackPowerPortName + } + STATUS current + DESCRIPTION + "A collection of objects that are used for control and status of + stack power ports." + ::= { cswStackWiseMIBGroups 6 } + +cswStackPowerNotificationGroup NOTIFICATION-GROUP + NOTIFICATIONS { + cswStackPowerPortLinkStatusChanged, + cswStackPowerPortOperStatusChanged, + cswStackPowerVersionMismatch, + cswStackPowerInvalidTopology, + cscwStackPowerBudgetWarrning, + cswStackPowerInvalidInputCurrent, + cswStackPowerInvalidOutputCurrent, + cswStackPowerUnderBudget, + cswStackPowerUnbalancedPowerSupplies, + cswStackPowerInsufficientPower, + cswStackPowerPriorityConflict, + cswStackPowerUnderVoltage, + cswStackPowerGLS, + cswStackPowerILS, + cswStackPowerSRLS, + cswStackPowerSSLS + } + STATUS current + DESCRIPTION + "A collection of notifications that are triggered whenever there + is either a change in stack power object or an error is + encountered." + ::= { cswStackWiseMIBGroups 7 } + +cswStackPowerEnableNotificationGroup OBJECT-GROUP + OBJECTS { cswEnableIndividualStackNotifications } + STATUS current + DESCRIPTION + "This group contains the notification enable objects for this + MIB." + ::= { cswStackWiseMIBGroups 8 } + +cswNotificationGroupSup1 NOTIFICATION-GROUP + NOTIFICATIONS { cswStackMemberToBeReloadedForUpgrade } + STATUS current + DESCRIPTION + "Additional notification required for data stack." + ::= { cswStackWiseMIBGroups 9 } + +cswStackPowerAllocatedGroup OBJECT-GROUP + OBJECTS { cswSwitchPowerAllocated } + STATUS current + DESCRIPTION + "A collection of objects providing the stack power allocation + information of a switch." + ::= { cswStackWiseMIBGroups 10 } + +cswStatusGroupRev2 OBJECT-GROUP + OBJECTS { + cswMaxSwitchNum, + cswMaxSwitchConfigPriority, + cswRingRedundant, + cswSwitchNumCurrent, + cswSwitchNumNextReload, + cswSwitchRole, + cswSwitchSwPriority, + cswSwitchHwPriority, + cswSwitchState, + cswSwitchMacAddress, + cswStackDomainNum, + cswStackType, + cswStackBandWidth + } + STATUS current + DESCRIPTION + "A collection of objects that are used for control and + status." + ::= { cswStackWiseMIBGroups 11 } + +cswDistrStackLinkStatusGroup OBJECT-GROUP + OBJECTS { cswDistrStackLinkBundleOperStatus } + STATUS current + DESCRIPTION + "A collection object(s) for control and status of the + distributed Stack Link." + ::= { cswStackWiseMIBGroups 12 } + +cswDistrStackPhyPortStatusGroup OBJECT-GROUP + OBJECTS { + cswDistrStackPhyPort, + cswDistrStackPhyPortOperStatus, + cswDistrStackPhyPortNbr, + cswDistrStackPhyPortNbrsw + } + STATUS current + DESCRIPTION + "A collection of objects for control and status of the + distributed stack port" + ::= { cswStackWiseMIBGroups 13 } + +END + + |