diff options
Diffstat (limited to 'MIBS/cambium/500/CAMBIUM-PTP500-MIB')
| -rw-r--r-- | MIBS/cambium/500/CAMBIUM-PTP500-MIB | 2588 |
1 files changed, 2588 insertions, 0 deletions
diff --git a/MIBS/cambium/500/CAMBIUM-PTP500-MIB b/MIBS/cambium/500/CAMBIUM-PTP500-MIB new file mode 100644 index 0000000..7d7aea4 --- /dev/null +++ b/MIBS/cambium/500/CAMBIUM-PTP500-MIB @@ -0,0 +1,2588 @@ + CAMBIUM-PTP500-MIB DEFINITIONS ::= BEGIN
+
+ IMPORTS
+ MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
+ Integer32, IpAddress,
+ enterprises
+ FROM SNMPv2-SMI
+ MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
+ FROM SNMPv2-CONF
+ DisplayString
+ FROM SNMPv2-TC;
+
+ cambium MODULE-IDENTITY
+ LAST-UPDATED "201403141604Z"
+ ORGANIZATION "Cambium Networks Ltd."
+ CONTACT-INFO
+ "Post: Simon Whitaker
+ Cambium Networks Ltd.
+ Unit B2,
+ Linhay Business Park,
+ Eastern Road,
+ Ashburton,
+ Devon.
+ TQ13 7UP
+ United Kingdom
+ Phone: +44 (0) 1364 655 500
+ Email: simon.whitaker@cambiumnetworks.com"
+ DESCRIPTION
+ "MIB for 105Mbps non-line-of-sight (NLOS) wireless ethernet bridge."
+ REVISION "201403141604Z"
+ DESCRIPTION "PTP500-05-04:
+ Added aAAControl group containing user table."
+ REVISION "201302080838Z"
+ DESCRIPTION "PTP500-05-03:
+ Removed encryptionEnabledMismatchTrap.
+ Renamed dfsChannelChangeTrap to channelChangeTrap."
+ REVISION "201207091750Z"
+ DESCRIPTION "PTP500-05-02:
+ Corrected REVISION DESCRIPTION clause for 05-01."
+ REVISION "201203281037Z"
+ DESCRIPTION "PTP500-05-01:
+ Updated ORGANIZATION and CONTACT-INFO.
+ Replaced syslogLocalLog with syslogState.
+ Added licensedCapacity and capacityLicenseMismatchTrap as part of SKU reduction.
+ Added support for HTTPS.
+ Added enabledDiagnosticAlarms attribute.
+ Added support for syslog client.
+ Removed lineOfSightModeInactive trap as part of SKU reduction (LOS no longer supported)."
+ REVISION "201107131657Z"
+ DESCRIPTION "PTP500-04-01:
+ Added latitude, longitude, altitude, searchState, accessMethod and groupID."
+ REVISION "201009221449Z"
+ DESCRIPTION "PTP500-04-00:
+ Changed root OID.
+ Added SNMPv3 support, TDD sync, DFS Table, BIT STRING types now OCTET STRING.
+ Added linkName, siteName.
+ Renamed ethernet attributes & traps."
+ REVISION "200905290925Z"
+ DESCRIPTION "PTP500-03-02: Added Telecoms circuit emulation."
+ REVISION "200811041022Z"
+ DESCRIPTION "PTP500-03-00: Added Link Symmetry."
+ REVISION "200806261644Z"
+ DESCRIPTION "PTP500-02-00: Added IEEE 802.1q & 802.1ad VLAN support."
+ REVISION "200804111808Z"
+ DESCRIPTION "PTP500-01-00"
+ ::= { enterprises 17713 }
+
+ -- Groups in cambium
+ ptp OBJECT IDENTIFIER ::= { cambium 1 }
+ ptmp OBJECT IDENTIFIER ::= { cambium 2 }
+ ptp500 OBJECT IDENTIFIER ::= { cambium 5 }
+
+ -- Groups in ptp500
+ dfs OBJECT IDENTIFIER ::= { ptp500 3 }
+ configuration OBJECT IDENTIFIER ::= { ptp500 5 }
+ ethernet OBJECT IDENTIFIER ::= { ptp500 6 }
+ telecom OBJECT IDENTIFIER ::= { ptp500 7 }
+ licence OBJECT IDENTIFIER ::= { ptp500 8 }
+ management OBJECT IDENTIFIER ::= { ptp500 9 }
+ phyControl OBJECT IDENTIFIER ::= { ptp500 10 }
+ phyStatus OBJECT IDENTIFIER ::= { ptp500 12 }
+ alarms OBJECT IDENTIFIER ::= { ptp500 13 }
+ smtp OBJECT IDENTIFIER ::= { ptp500 15 }
+ snmpControl OBJECT IDENTIFIER ::= { ptp500 16 }
+ sntp OBJECT IDENTIFIER ::= { ptp500 17 }
+ reset OBJECT IDENTIFIER ::= { ptp500 18 }
+ versions OBJECT IDENTIFIER ::= { ptp500 19 }
+ pubStats OBJECT IDENTIFIER ::= { ptp500 20 }
+ encryption OBJECT IDENTIFIER ::= { ptp500 22 }
+ tDDControl OBJECT IDENTIFIER ::= { ptp500 23 }
+ aAAControl OBJECT IDENTIFIER ::= { ptp500 25 }
+ syslogControl OBJECT IDENTIFIER ::= { ptp500 24 }
+ supplementary OBJECT IDENTIFIER ::= { ptp500 96 }
+ ptpGroups OBJECT IDENTIFIER ::= { ptp500 98 }
+ ptpTraps OBJECT IDENTIFIER ::= { ptp500 99 }
+ ptpTrapPrefix OBJECT IDENTIFIER ::= { ptpTraps 0 }
+
+ -- Compliance information
+ --
+ ptpCompliance MODULE-COMPLIANCE
+ STATUS current
+ DESCRIPTION
+ "The compliance statement for the Cambium PTP MIB"
+ MODULE -- this module
+ MANDATORY-GROUPS { dfsGroup
+ , configurationGroup
+ , ethernetGroup
+ , telecomGroup
+ , licenceGroup
+ , managementGroup
+ , phyControlGroup
+ , phyStatusGroup
+ , alarmsGroup
+ , smtpGroup
+ , snmpControlGroup
+ , sntpGroup
+ , resetGroup
+ , versionsGroup
+ , pubStatsGroup
+ , encryptionGroup
+ , tDDControlGroup
+ , aAAControlGroup
+ , syslogControlGroup
+ , supplementaryGroup
+ , notificationsGroup
+ }
+ ::= { ptp500 97 }
+
+ dfsGroup OBJECT-GROUP
+ OBJECTS { dfsTableNumber
+ , dfsMeans
+ , dfsNineNinePointNinePercentiles
+ , dfsPeaks
+ }
+ STATUS current
+ DESCRIPTION "The dfs object group."
+ ::= { ptpGroups 3 }
+
+ configurationGroup OBJECT-GROUP
+ OBJECTS { iPAddress
+ , subnetMask
+ , gatewayIPAddress
+ , targetMACAddress
+ , masterSlaveMode
+ , maximumTransmitPower
+ , antennaGain
+ , cableLoss
+ , eIRP
+ , channelBandwidth
+ , remoteIPAddress
+ , linkName
+ , siteName
+ , accessMethod
+ , groupID
+ }
+ STATUS current
+ DESCRIPTION "The configuration object group."
+ ::= { ptpGroups 5 }
+
+ ethernetGroup OBJECT-GROUP
+ OBJECTS { dataPortAutoNegotiation
+ , dataPortAutoNegAdvertisement
+ , dataPortAutoMdix
+ , dataPortStatus
+ , dataPortSpeedAndDuplex
+ , dataPortWirelessDownAlert
+ , useVLANForManagementInterfaces
+ , vLANManagementPriority
+ , vLANManagementVID
+ , vLANPriorityTableNumber
+ , vLANPriorityQueueMapping
+ }
+ STATUS current
+ DESCRIPTION "The ethernet object group."
+ ::= { ptpGroups 6 }
+
+ telecomGroup OBJECT-GROUP
+ OBJECTS { telecomsInterface
+ , telecomsChannelStatus
+ , telecomsLineCode
+ , telecomsCableLength
+ , telecomsLoopback
+ }
+ STATUS current
+ DESCRIPTION "The telecom object group."
+ ::= { ptpGroups 7 }
+
+ licenceGroup OBJECT-GROUP
+ OBJECTS { regionCode
+ , productVariant
+ , productName
+ , ethernetFiberSupport
+ , frequencyVariant
+ , bandwidthVariant
+ , constantPowerSpectralDensity
+ , sNMPv3Enable
+ , licensedCapacity
+ }
+ STATUS current
+ DESCRIPTION "The licence object group."
+ ::= { ptpGroups 8 }
+
+ managementGroup OBJECT-GROUP
+ OBJECTS { installStatus
+ , installArmState
+ , tFTPServerIPAddress
+ , tFTPServerPortNumber
+ , tFTPSoftwareUpgradeFileName
+ , tFTPStartSoftwareUpgrade
+ , tFTPSoftwareUpgradeStatus
+ , tFTPSoftwareUpgradeStatusText
+ , tFTPSoftwareUpgradeStatusAdditionalText
+ , hTTPAccessEnabled
+ , telnetAccessEnabled
+ , hTTPPortNumber
+ , hTTPSPortNumber
+ , telnetPortNumber
+ , hTTPSAccessEnabled
+ }
+ STATUS current
+ DESCRIPTION "The management object group."
+ ::= { ptpGroups 9 }
+
+ phyControlGroup OBJECT-GROUP
+ OBJECTS { linkSymmetry
+ , linkModeOptimisation
+ , userConfiguredMaxModulationMode
+ , remoteMaximumTransmitPower
+ }
+ STATUS current
+ DESCRIPTION "The phyControl object group."
+ ::= { ptpGroups 10 }
+
+ phyStatusGroup OBJECT-GROUP
+ OBJECTS { receivePower
+ , vectorError
+ , transmitPower
+ , range
+ , linkLoss
+ , receiveChannel
+ , transmitChannel
+ , receiveModulationMode
+ , transmitModulationMode
+ , receiveFreqMHz
+ , transmitFreqMHz
+ , signalStrengthRatio
+ , receiveFreqKHz
+ , transmitFreqKHz
+ , searchState
+ }
+ STATUS current
+ DESCRIPTION "The phyStatus object group."
+ ::= { ptpGroups 12 }
+
+ alarmsGroup OBJECT-GROUP
+ OBJECTS { unitOutOfCalibration
+ , incompatibleRegionCodes
+ , noWirelessChannelAvailable
+ , wirelessLinkDisabledWarning
+ , dataPortDisabledWarning
+ , dataPortConfigurationMismatch
+ , incompatibleMasterAndSlave
+ , tDDSynchronizationStatus
+ , tDDSynchronizationAlarm
+ , linkModeOptimizationMismatch
+ , capacityLicenseMismatch
+ }
+ STATUS current
+ DESCRIPTION "The alarms object group."
+ ::= { ptpGroups 13 }
+
+ smtpGroup OBJECT-GROUP
+ OBJECTS { sMTPEmailAlert
+ , sMTPServerIPAddress
+ , sMTPServerPortNumber
+ , sMTPSourceEmailAddress
+ , sMTPDestinationEmailAddress
+ , sMTPEnabledMessages
+ }
+ STATUS current
+ DESCRIPTION "The smtp object group."
+ ::= { ptpGroups 15 }
+
+ snmpControlGroup OBJECT-GROUP
+ OBJECTS { sNMPPortNumber
+ , sNMPCommunityString
+ , sNMPTrapTableNumber
+ , sNMPTrapVersion
+ , sNMPEnabledTraps
+ , enabledDiagnosticAlarms
+ , sNMPSendAllTrapsAtStartup
+ , sNMPTrapIPAddress
+ , sNMPTrapPortNumber
+ }
+ STATUS current
+ DESCRIPTION "The snmpControl object group."
+ ::= { ptpGroups 16 }
+
+ sntpGroup OBJECT-GROUP
+ OBJECTS { sNTPState
+ , sNTPServerIPAddress
+ , sNTPServerPortNumber
+ , sNTPPollInterval
+ , sNTPSync
+ , sNTPLastSync
+ , systemClock
+ , timeZone
+ , daylightSaving
+ }
+ STATUS current
+ DESCRIPTION "The sntp object group."
+ ::= { ptpGroups 17 }
+
+ resetGroup OBJECT-GROUP
+ OBJECTS { systemReset
+ }
+ STATUS current
+ DESCRIPTION "The reset object group."
+ ::= { ptpGroups 18 }
+
+ versionsGroup OBJECT-GROUP
+ OBJECTS { softwareVersion
+ , hardwareVersion
+ , secondarySoftwareVersion
+ , bootVersion
+ }
+ STATUS current
+ DESCRIPTION "The versions object group."
+ ::= { ptpGroups 19 }
+
+ pubStatsGroup OBJECT-GROUP
+ OBJECTS { receiveDataRate
+ , transmitDataRate
+ , aggregateDataRate
+ , wirelessLinkAvailability
+ , wirelessLinkStatus
+ , byteErrorRatio
+ , receiveModulationModeDetail
+ }
+ STATUS current
+ DESCRIPTION "The pubStats object group."
+ ::= { ptpGroups 20 }
+
+ encryptionGroup OBJECT-GROUP
+ OBJECTS { encryptionAlgorithm
+ }
+ STATUS current
+ DESCRIPTION "The encryption object group."
+ ::= { ptpGroups 22 }
+
+ tDDControlGroup OBJECT-GROUP
+ OBJECTS { tDDSynchronizationMode
+ }
+ STATUS current
+ DESCRIPTION "The tDDControl object group."
+ ::= { ptpGroups 23 }
+
+ aAAControlGroup OBJECT-GROUP
+ OBJECTS { userTableNumber
+ , userName
+ , userRole
+ , userEnabled
+ , userPassword
+ }
+ STATUS current
+ DESCRIPTION "The aAAControl object group."
+ ::= { ptpGroups 25 }
+
+ syslogControlGroup OBJECT-GROUP
+ OBJECTS { syslogClient
+ , syslogState
+ }
+ STATUS current
+ DESCRIPTION "The syslogControl object group."
+ ::= { ptpGroups 24 }
+
+ supplementaryGroup OBJECT-GROUP
+ OBJECTS { longitude
+ , latitude
+ , altitude
+ }
+ STATUS current
+ DESCRIPTION "The supplementary object group."
+ ::= { ptpGroups 96 }
+
+ notificationsGroup NOTIFICATION-GROUP
+ NOTIFICATIONS { channelChangeTrap
+ , dfsImpulsiveInterferenceTrap
+ , dataPortStatusTrap
+ , telecomsChannelStatusTrap
+ , telecomsLoopbackTrap
+ , regionCodeTrap
+ , installStatusTrap
+ , installArmStateTrap
+ , unitOutOfCalibrationTrap
+ , incompatibleRegionCodesTrap
+ , noWirelessChannelAvailableTrap
+ , wirelessLinkDisabledWarningTrap
+ , dataPortDisabledWarningTrap
+ , dataPortConfigurationMismatchTrap
+ , incompatibleMasterAndSlaveTrap
+ , sNTPSyncTrap
+ , tDDSynchronizationAlarmTrap
+ , linkModeOptimizationMismatchTrap
+ , capacityLicenseMismatchTrap
+ , syslogStateTrap
+ , syslogLocalNearlyFullTrap
+ , syslogLocalWrappedTrap
+ , syslogClientTrap
+ }
+ STATUS current
+ DESCRIPTION "The notifications group."
+ ::= { ptpGroups 99 }
+
+
+ DfsTableEntry ::=
+ SEQUENCE { dfsTableIndex INTEGER
+ , dfsMeans Integer32
+ , dfsNineNinePointNinePercentiles Integer32
+ , dfsPeaks Integer32
+ }
+
+ dfsTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF DfsTableEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ " A table storing a snapshot of various DFS measurements for each channel"
+ ::= { dfs 2 }
+
+ dfsTableEntry OBJECT-TYPE
+ SYNTAX DfsTableEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Table DfsTable"
+ INDEX { dfsTableIndex }
+ ::= { dfsTable 1 }
+
+ VLANPriorityTableEntry ::=
+ SEQUENCE { vLANPriorityQueueMapping INTEGER
+ , vLANPriorityTableIndex INTEGER
+ }
+
+ vLANPriorityTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF VLANPriorityTableEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ " A priority queue mapping table. This is a list of packet queues indexed by VLAN priority."
+ ::= { ethernet 15 }
+
+ vLANPriorityTableEntry OBJECT-TYPE
+ SYNTAX VLANPriorityTableEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Table VLANPriorityTable"
+ INDEX { vLANPriorityTableIndex }
+ ::= { vLANPriorityTable 1 }
+
+ SNMPTrapTableEntry ::=
+ SEQUENCE { sNMPTrapTableIndex INTEGER
+ , sNMPTrapIPAddress IpAddress
+ , sNMPTrapPortNumber INTEGER
+ }
+
+ sNMPTrapTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF SNMPTrapTableEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ " SNMP trap configuration table."
+ ::= { snmpControl 4 }
+
+ sNMPTrapTableEntry OBJECT-TYPE
+ SYNTAX SNMPTrapTableEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Table SNMPTrapTable"
+ INDEX { sNMPTrapTableIndex }
+ ::= { sNMPTrapTable 1 }
+
+ UserTableEntry ::=
+ SEQUENCE { userTableIndex INTEGER
+ , userName OCTET STRING
+ , userRole INTEGER
+ , userEnabled INTEGER
+ , userPassword OCTET STRING
+ }
+
+ userTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF UserTableEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ " The User Table Control group contains objects specifically for user account management."
+ ::= { aAAControl 2 }
+
+ userTableEntry OBJECT-TYPE
+ SYNTAX UserTableEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Table UserTable"
+ INDEX { userTableIndex }
+ ::= { userTable 1 }
+
+ -- Dfs group attribute definitions
+ --
+ dfsTableNumber OBJECT-TYPE
+ SYNTAX INTEGER (1..63)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Number of entries in the dfsTable"
+ ::= { dfs 1 }
+
+ -- DfsTable group attribute definitions
+ --
+ dfsTableIndex OBJECT-TYPE
+ SYNTAX INTEGER (1..63)
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "used to index values in the dfsTable."
+ ::= { dfsTableEntry 1 }
+
+ dfsMeans OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Snapshot of DFS means"
+ ::= { dfsTableEntry 2 }
+
+ dfsNineNinePointNinePercentiles OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Snapshot of DFS 99.9 percentiles"
+ ::= { dfsTableEntry 3 }
+
+ dfsPeaks OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Snapshot of DFS peaks"
+ ::= { dfsTableEntry 4 }
+
+ -- Configuration group attribute definitions
+ --
+ iPAddress OBJECT-TYPE
+ SYNTAX IpAddress
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Internet protocol (IP) address. This address is used by
+ the family of Internet protocols to uniquely identify the
+ unit on a network. NB: A system reboot is required to
+ activate changes to this attribute."
+ ::= { configuration 1 }
+
+ subnetMask OBJECT-TYPE
+ SYNTAX IpAddress
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "A subnet allows the flow of network traffic between
+ hosts to be segregated based on a network configuration.
+ By organizing hosts into logical groups, subnetting can
+ improve network security and performance. NB: A system
+ reboot is required to activate changes to this attribute"
+ ::= { configuration 2 }
+
+ gatewayIPAddress OBJECT-TYPE
+ SYNTAX IpAddress
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The IP address of a computer on the current network that
+ is currently acting as a network gateway. A gateway acts
+ as an entrance / exit to packets from / to other
+ networks. NB: A system reboot is required to activate
+ changes to this attribute"
+ ::= { configuration 3 }
+
+ targetMACAddress OBJECT-TYPE
+ SYNTAX OCTET STRING (SIZE(6))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "MAC address of the PTP wireless unit forming the other
+ end of the PTP link"
+ ::= { configuration 4 }
+
+ masterSlaveMode OBJECT-TYPE
+ SYNTAX INTEGER {
+ master(0),
+ slave(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The PTP wireless link operates using a master and slave
+ relationship"
+ ::= { configuration 5 }
+
+ maximumTransmitPower OBJECT-TYPE
+ SYNTAX INTEGER (-100..27)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Maximum transmit power the wireless unit is permitted to
+ use when establishing and maintaining the wireless link"
+ ::= { configuration 6 }
+
+ antennaGain OBJECT-TYPE
+ SYNTAX INTEGER (0..610)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Antenna Gain. Expressed in 10ths of dBi. NB: This
+ attribute is ignored for variants with an integral
+ antenna."
+ ::= { configuration 7 }
+
+ cableLoss OBJECT-TYPE
+ SYNTAX INTEGER (0..255)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Loss in the cable between the ODU and the antenna.
+ Expressed in 10ths of dB. NB: This attribute is ignored
+ for variants with an integral antenna."
+ ::= { configuration 8 }
+
+ eIRP OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Effective Isotropic Radiated Power (EIRP) describes the
+ strength of the radio signal leaving the wireless unit.
+ Expressed in 10ths of dBm"
+ ::= { configuration 9 }
+
+ channelBandwidth OBJECT-TYPE
+ SYNTAX INTEGER {
+ bw30MHz(0),
+ bw15MHz(1),
+ bw10MHz(2),
+ bw5MHz(3),
+ bw20MHz(4)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This control sets the bandwidth of the transmit and
+ receive radio channels"
+ ::= { configuration 11 }
+
+ remoteIPAddress OBJECT-TYPE
+ SYNTAX IpAddress
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "IP Address of the peer wireless unit"
+ ::= { configuration 12 }
+
+ linkName OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..63))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Name of the PTP link allocated by the System
+ Administrator. Used to establish a connection with the
+ correct PTP wireless unit at the other end of the link.
+ NOTE: The link name MUST be the same at both ends of the
+ PTP link."
+ ::= { configuration 14 }
+
+ siteName OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..63))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This field contains a user-provided description of the
+ site name together with any additional notes"
+ ::= { configuration 15 }
+
+ accessMethod OBJECT-TYPE
+ SYNTAX INTEGER {
+ linkAccess(0),
+ linkNameAccess(1),
+ groupAccess(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This controls whether the link can be established
+ between pre-paired Master-Slave using MAC addresses (Link
+ Access) or by using link name (Link Name Access)"
+ ::= { configuration 16 }
+
+ groupID OBJECT-TYPE
+ SYNTAX INTEGER (0..255)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "When Access Method is set to Group Access, the Group ID
+ identifies all the units belonging to the same group.
+ Group Access is only supported on some platforms"
+ ::= { configuration 17 }
+
+ -- Ethernet group attribute definitions
+ --
+ dataPortAutoNegotiation OBJECT-TYPE
+ SYNTAX INTEGER {
+ disabled(0),
+ enabled(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This controls whether the local Ethernet interface
+ configuration is automatically negotiated or forced. Do
+ not use a forced setting together with auto negotiation
+ at the Ethernet link partner. If you want to run your
+ Ethernet link at a fixed speed and duplex then you would
+ normally leave auto negotiation enabled and only enable
+ the single Auto Neg Advertisement option that you want
+ the link to run in - FORCING ETHERNET CONFIGURATION IS A
+ LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE
+ HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST
+ ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET
+ LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE
+ LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED
+ EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The
+ new setting will only take effect after a system reboot."
+ ::= { ethernet 1 }
+
+ dataPortAutoNegAdvertisement OBJECT-TYPE
+ SYNTAX BITS {
+ negInvalid(2),
+ neg10MbpsHalfDuplex(3),
+ neg10MbpsFullDuplex(4),
+ neg100MbpsHalfDuplex(5),
+ neg100MbpsFullDuplex(6),
+ negUnknown1(7)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This sets the different Ethernet configurations that
+ will be advertised during auto negotiation. NB: The new
+ setting will only take effect after a system reboot.
+ WARNING: Duplex mismatch may result if both ends of the
+ Ethernet link do not have the same settings. Do not auto
+ negotiation together with a fixed setting at the Ethernet
+ link partner. WARNING: Make sure that you select
+ option(s) that you know your connected equipment can
+ cater for!"
+ ::= { ethernet 2 }
+
+ dataPortAutoMdix OBJECT-TYPE
+ SYNTAX INTEGER {
+ disabled(0),
+ enabled(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This enables/disables the Auto MDI/MDIX capability. NB:
+ The new setting will only take effect after a system
+ reboot"
+ ::= { ethernet 3 }
+
+ dataPortStatus OBJECT-TYPE
+ SYNTAX INTEGER {
+ down(0),
+ copperLinkUp(1),
+ fiberLinkUp(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Current status of the Ethernet link. NB: a change of
+ state may generate an SNMP trap and/or SMTP email alert"
+ ::= { ethernet 4 }
+
+ dataPortSpeedAndDuplex OBJECT-TYPE
+ SYNTAX INTEGER {
+ speed1000MbpsFullDuplex(0),
+ speed100MbpsFullDuplex(1),
+ speed100MbpsHalfDuplex(2),
+ speed10MbpsFullDuplex(3),
+ speed10MbpsHalfDuplex(4),
+ speedUnknown6(5)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The current speed and duplex of the Ethernet link"
+ ::= { ethernet 5 }
+
+ dataPortWirelessDownAlert OBJECT-TYPE
+ SYNTAX INTEGER {
+ disabled(0),
+ enabled(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "When enabled, this causes the Ethernet link to be
+ dropped briefly when the wireless link drops. This is so
+ that spanning tree algorithms can quickly detect that
+ there is a problem."
+ ::= { ethernet 6 }
+
+ useVLANForManagementInterfaces OBJECT-TYPE
+ SYNTAX INTEGER {
+ noVLANTagging(0),
+ iEEE8021QTaggedCTagType8100(1),
+ iEEE8021adTaggedSTagorBTagType88a8(2)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This controls whether the management interfaces
+ (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new
+ setting will only take effect after a system reboot"
+ ::= { ethernet 7 }
+
+ vLANManagementPriority OBJECT-TYPE
+ SYNTAX INTEGER (0..7)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This VLAN Priority (0-7) will be included in packets
+ generated by the management interfaces. NB: The new
+ setting will only take effect after a system reboot"
+ ::= { ethernet 8 }
+
+ vLANManagementVID OBJECT-TYPE
+ SYNTAX INTEGER (0..4094)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This VLAN VID (0-4094) will be included in packets
+ generated by the management interfaces. NB: The new
+ setting will only take effect after a system reboot"
+ ::= { ethernet 11 }
+
+ vLANPriorityTableNumber OBJECT-TYPE
+ SYNTAX INTEGER (9)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Number of entries in the vLANPriorityTable."
+ ::= { ethernet 14 }
+
+ -- VLANPriorityTable group attribute definitions
+ --
+ vLANPriorityQueueMapping OBJECT-TYPE
+ SYNTAX INTEGER {
+ q0(0),
+ q1(1),
+ q2(2),
+ q3(3),
+ q4(4),
+ q5(5),
+ q6(6),
+ q7(7)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Mapping of VLAN priority flag to packet queue. The
+ higher the queue number the greater its priority."
+ ::= { vLANPriorityTableEntry 1 }
+
+ vLANPriorityTableIndex OBJECT-TYPE
+ SYNTAX INTEGER {
+ p0(1),
+ p1(2),
+ p2(3),
+ p3(4),
+ p4(5),
+ p5(6),
+ p6(7),
+ p7(8),
+ untagged(9)
+ }
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "VLAN priority flag, used to index values in the
+ vLANPriorityTable."
+ ::= { vLANPriorityTableEntry 2 }
+
+ -- Telecom group attribute definitions
+ --
+ telecomsInterface OBJECT-TYPE
+ SYNTAX INTEGER {
+ none(0),
+ e1(1),
+ t1(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The line interface type. If this is set to 'None' then
+ the telecoms interfaces are disabled, and the telecom
+ group attributes will be ignored."
+ ::= { telecom 1 }
+
+ telecomsChannelStatus OBJECT-TYPE
+ SYNTAX INTEGER {
+ disabled(0),
+ noSignalLocal(1),
+ noSignalRemote(2),
+ noSignalLocalandRemote(3),
+ up(4),
+ remoteTiming(5),
+ noSignalLocalandRemoteTiming(6)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Current status of telecoms channel. NB: a change of
+ state may generate an SNMP trap and/or SMTP email alert"
+ ::= { telecom 2 }
+
+ telecomsLineCode OBJECT-TYPE
+ SYNTAX INTEGER {
+ aMI(0),
+ b8ZSHDB3(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The line code setting of the telecoms interface. This
+ must match the setting of the device connected to this
+ interface"
+ ::= { telecom 4 }
+
+ telecomsCableLength OBJECT-TYPE
+ SYNTAX INTEGER {
+ feet133(0),
+ feet266(1),
+ feet399(2),
+ feet533(3),
+ feet655(4)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The length of the cable connected to the telecoms
+ interface, measured in feet"
+ ::= { telecom 6 }
+
+ telecomsLoopback OBJECT-TYPE
+ SYNTAX INTEGER {
+ none(0),
+ copper(1),
+ wireless(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The loopback status of telecoms channel. This is
+ intended for installation testing and should be set to
+ 'None' for normal operation. The wire connections to a
+ unit can be tested by applying a 'Copper' loopback to the
+ local unit. The wireless connection to the remote unit
+ can be tested by applying a 'Wireless' loopback to the
+ remote unit with no loopback on the local unit. When
+ applying a wireless loopback, please ensure that the
+ other end of the link has a loopback setting of 'None'.
+ NB: a change of state may generate an SNMP trap and/or
+ SMTP email alert"
+ ::= { telecom 8 }
+
+ -- Licence group attribute definitions
+ --
+ regionCode OBJECT-TYPE
+ SYNTAX INTEGER {
+ regionCodeInvalid(0),
+ regionCode1(1),
+ regionCode2(2),
+ regionCode3(3),
+ regionCode4(4),
+ regionCode5(5),
+ regionCode6(6),
+ regionCode7(7),
+ regionCode8(8),
+ regionCode9(9),
+ regionCode10(10),
+ regionCode11(11),
+ regionCode12(12),
+ regionCode13(13),
+ regionCode14(14),
+ regionCode15(15),
+ regionCode16(16),
+ regionCode17(17),
+ regionCode18(18),
+ regionCode19(19),
+ regionCode20(20),
+ regionCode21(21),
+ regionCode22(22),
+ regionCode23(23),
+ regionCode24(24),
+ regionCode25(25),
+ regionCode26(26),
+ regionCode27(27),
+ regionCode28(28),
+ regionCode29(29),
+ regionCode30(30),
+ regionCode31(31)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The region code prohibits the wireless unit from
+ operating outside the regulated limits. An invalid region
+ code indicates a corrupted licence key. NB: a change of
+ state may generate an SNMP trap and/or SMTP email alert"
+ ::= { licence 1 }
+
+ productVariant OBJECT-TYPE
+ SYNTAX INTEGER {
+ pTPxx400Full(0),
+ pTPxx400Deprecated1(1),
+ pTPxx400Deprecated2(2),
+ pTPxx400Lite(3),
+ spare1(4),
+ pTPxx300(5),
+ spare2(6),
+ spare3(7),
+ pTPxx500FullDeprecated(8),
+ pTPxx500LiteDeprecated(9),
+ pTPxx500(10),
+ pTPxx600Lite(11),
+ pTPxx600Full(12),
+ spare5(13),
+ spare6(14),
+ pTP800(15)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The product variant"
+ ::= { licence 2 }
+
+ productName OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..63))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Name of the product variant"
+ ::= { licence 3 }
+
+ ethernetFiberSupport OBJECT-TYPE
+ SYNTAX INTEGER {
+ disabled(0),
+ enabled(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Ethernet fiber support availability on this wireless
+ unit"
+ ::= { licence 4 }
+
+ frequencyVariant OBJECT-TYPE
+ SYNTAX INTEGER {
+ freq5800MHz(0),
+ freq5400MHz(1),
+ freq4900MHz(2),
+ freq2500MHz(3),
+ freq5800MHz2(4),
+ freq5400MHz2(5),
+ freq4500MHz(6),
+ freq5900MHz(7),
+ freq5200MHz(8),
+ freq5100MHz(9),
+ freq4800MHz(10)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Frequency variant of the wireless unit"
+ ::= { licence 5 }
+
+ bandwidthVariant OBJECT-TYPE
+ SYNTAX INTEGER {
+ bw30MHz(0),
+ bw15MHz(1),
+ bw10MHz(2),
+ bw5MHz(3),
+ bw20MHz(4)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Bandwidth variant of the wireless unit"
+ ::= { licence 6 }
+
+ constantPowerSpectralDensity OBJECT-TYPE
+ SYNTAX INTEGER {
+ constant(0),
+ fullPower(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Constant power spectral density mode control"
+ ::= { licence 7 }
+
+ sNMPv3Enable OBJECT-TYPE
+ SYNTAX INTEGER {
+ disabled(0),
+ enabled(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "SNMPv3 availability control"
+ ::= { licence 9 }
+
+ licensedCapacity OBJECT-TYPE
+ SYNTAX INTEGER {
+ capacity25Mbps(0),
+ capacity52Mbps(1),
+ capacity105Mbps(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Maximum allowable data rate for ethernet frames
+ permitted by the licence key. The actual data rate
+ depends upon the prevailing wireless conditions"
+ ::= { licence 11 }
+
+ -- Management group attribute definitions
+ --
+ installStatus OBJECT-TYPE
+ SYNTAX INTEGER {
+ ok(0),
+ wrongPeer(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "A non-zero value indicates that signalling was received
+ with the wrong MAC address or a mismatched link name. NB:
+ It is very unusual to detect this, because units with
+ mis-configured Target MAC Address will normally fail to
+ establish a wireless link. However, rare circumstances
+ may establish a partial wireless link and detect this
+ situation. NB: A non-zero value on start-up, or a change
+ of value during operation, may generate an SNMP trap
+ and/or SMTP email alert"
+ ::= { management 3 }
+
+ installArmState OBJECT-TYPE
+ SYNTAX INTEGER {
+ disarmed(0),
+ armed(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Indicates if the unit is being installed. NB: a value
+ other than 'disarmed' on startup, or a change of state
+ during operation may generate an SNMP trap and/or SMTP
+ email alert"
+ ::= { management 4 }
+
+ tFTPServerIPAddress OBJECT-TYPE
+ SYNTAX IpAddress
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "IP address of the TFTP Server from which the TFTP
+ Software Upgrade File Name will be retrieved"
+ ::= { management 5 }
+
+ tFTPServerPortNumber OBJECT-TYPE
+ SYNTAX INTEGER (0..65535)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The port number of the TFTP Server from which the TFTP
+ Software Upgrade File Name will be retrieved"
+ ::= { management 6 }
+
+ tFTPSoftwareUpgradeFileName OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..127))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Filename of the Software Upgrade to be loaded from the
+ TFTP Server"
+ ::= { management 7 }
+
+ tFTPStartSoftwareUpgrade OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Write '1' to this attribute to start the TFTP software
+ upgrade process. The attribute will be reset to 0 when
+ the upgrade process has finished"
+ ::= { management 8 }
+
+ tFTPSoftwareUpgradeStatus OBJECT-TYPE
+ SYNTAX INTEGER {
+ idle(0),
+ uploadinprogress(1),
+ uploadsuccessfulprogrammingFLASH(2),
+ upgradesuccessfulreboottorunthenewsoftwareimage(3),
+ upgradefailed(4)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The current status of the TFTP Software upgrade process"
+ ::= { management 9 }
+
+ tFTPSoftwareUpgradeStatusText OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..127))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Descriptive text describing the status of the TFTP
+ Software upgrade process, including any error details"
+ ::= { management 10 }
+
+ tFTPSoftwareUpgradeStatusAdditionalText OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..127))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Any additional text describing the status of the TFTP
+ Software upgrade process, including any error details"
+ ::= { management 11 }
+
+ hTTPAccessEnabled OBJECT-TYPE
+ SYNTAX INTEGER {
+ no(0),
+ yes(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This controls whether or not HTTP access is enabled,
+ i.e. if this is disabled (0) then the unit will not
+ respond to any requests on the HTTP port. Remote
+ management via HTTPS is not affected by this setting. Any
+ change in this setting will not take effect until the
+ unit has been rebooted. (Factory default = Enabled)"
+ ::= { management 12 }
+
+ telnetAccessEnabled OBJECT-TYPE
+ SYNTAX INTEGER {
+ no(0),
+ yes(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This controls whether or not Telnet access is enabled,
+ i.e. if this is disabled (0) then the unit will not
+ respond to any requests on the TELNET port. Any change in
+ this setting will not take effect until the unit has been
+ rebooted. (Factory default = Disabled)"
+ ::= { management 13 }
+
+ hTTPPortNumber OBJECT-TYPE
+ SYNTAX INTEGER (0..65535)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This controls the port number for HTTP access. A value
+ of zero will use the default port number. Any change in
+ this setting will not take effect until the unit has been
+ rebooted. (Factory default = 80)"
+ ::= { management 14 }
+
+ hTTPSPortNumber OBJECT-TYPE
+ SYNTAX INTEGER (0..65535)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This controls the port number for HTTPS access. A value
+ of zero will use the default port number. Availability of
+ HTTPS is controlled via the Licence Key. Any change in
+ this setting will not take effect until the unit has been
+ rebooted. (Factory default = 443)"
+ ::= { management 15 }
+
+ telnetPortNumber OBJECT-TYPE
+ SYNTAX INTEGER (0..65535)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This controls the port number for TELNET access. A value
+ of zero will use the default port number. Any change in
+ this setting will not take effect until the unit has been
+ rebooted. (Factory default = 23)"
+ ::= { management 16 }
+
+ hTTPSAccessEnabled OBJECT-TYPE
+ SYNTAX INTEGER {
+ no(0),
+ yes(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This controls whether or not HTTPS access is enabled,
+ i.e. if this is disabled (0) then the unit will not
+ respond to any requests on the HTTPS port. Remote
+ management via HTTP is not affected by this setting. Any
+ change in this setting will not take effect until the
+ unit has been rebooted. (Factory default = Enabled)"
+ ::= { management 17 }
+
+ -- PhyControl group attribute definitions
+ --
+ linkSymmetry OBJECT-TYPE
+ SYNTAX INTEGER {
+ symmetryAdaptive(0),
+ symmetry3to1(1),
+ symmetry1to1(2),
+ symmetry1to3(3)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "In fixed asymmetric mode (3 to 1) the transmit time is
+ three times as long as the receive time. In fixed
+ symmetric mode (1 to 1) the unit spends an equal amount
+ of time transmitting and receiving. In fixed asymmetric
+ mode (1 to 3) the receive time is three times as long as
+ the transmit time. In adaptive mode the transmit and
+ receive periods adjust with applied load. NB: only
+ applicable for master nodes."
+ ::= { phyControl 1 }
+
+ linkModeOptimisation OBJECT-TYPE
+ SYNTAX INTEGER {
+ iPTraffic(0),
+ tDMTraffic(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Optimises the wireless link behavior for the type of
+ traffic to be carried. In 'IP Traffic' mode, the wireless
+ link will minimise transmission errors by automatically
+ adapting the modulation mode. In 'TDM Traffic' mode, the
+ wireless link will minimise transmission latency and
+ preserve throughput by maintaining a higher modulation
+ mode in the presence of a limited number of errors. The
+ 'TDM Traffic' mode is recommended for E1/T1 applications
+ and connectionless protocols."
+ ::= { phyControl 2 }
+
+ userConfiguredMaxModulationMode OBJECT-TYPE
+ SYNTAX INTEGER {
+ modBpsk50percent(0),
+ modQpsk50percent(1),
+ modQpsk75percent(2),
+ mod16qam50percent(3),
+ mod16qam75percent(4),
+ mod64qam67percent(5),
+ mod64qam83percent(6)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The maximum receive modulation mode controls the MAX
+ mode used for adaptive modulation. NOTE: This attribute
+ is automatically disabled when the installation agent is
+ armed. To disarm the installation agent use the
+ installation wizard"
+ ::= { phyControl 3 }
+
+ remoteMaximumTransmitPower OBJECT-TYPE
+ SYNTAX INTEGER (-100..27)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Maximum transmit power the remote wireless unit is
+ permitted to use when establishing and maintaining the
+ wireless link"
+ ::= { phyControl 4 }
+
+ -- PhyStatus group attribute definitions
+ --
+ receivePower OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Receive power expressed in tenths of a dBm"
+ ::= { phyStatus 1 }
+
+ vectorError OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The vector error measurement compares the received
+ signal's IQ modulation characteristics to an ideal signal
+ to determine the composite error vector magnitude. The
+ value represented by this attribute is the average vector
+ error over the previous second expressed in tenths of a
+ dB"
+ ::= { phyStatus 2 }
+
+ transmitPower OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Transmit power expressed in tenths of a dBm"
+ ::= { phyStatus 3 }
+
+ range OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Distance between the two peer wireless units expressed
+ in tenths of a kilometer"
+ ::= { phyStatus 4 }
+
+ linkLoss OBJECT-TYPE
+ SYNTAX INTEGER (-500..500)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The wireless link loss expressed in tenths of a dB"
+ ::= { phyStatus 5 }
+
+ receiveChannel OBJECT-TYPE
+ SYNTAX INTEGER (0..63)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Current active receive channel"
+ ::= { phyStatus 6 }
+
+ transmitChannel OBJECT-TYPE
+ SYNTAX INTEGER (0..63)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Current active transmit channel"
+ ::= { phyStatus 7 }
+
+ receiveModulationMode OBJECT-TYPE
+ SYNTAX INTEGER {
+ modAcquisition(0),
+ modBpsk50percent(1),
+ modQpsk50percentSingle(2),
+ modQpsk75percentSingle(3),
+ mod16qam50percentSingle(4),
+ mod16qam75percentSingle(5),
+ mod64qam67percentSingle(6),
+ mod64qam83percentSingle(7),
+ modReserved1(8),
+ modQpsk50percentDual(9),
+ modQpsk75percentDual(10),
+ mod16qam50percentDual(11),
+ mod16qam75percentDual(12),
+ mod64qam67percentDual(13),
+ mod64qam83percentDual(14),
+ modReserved2(15)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Current active receive modulation mode"
+ ::= { phyStatus 8 }
+
+ transmitModulationMode OBJECT-TYPE
+ SYNTAX INTEGER {
+ modAcquisition(0),
+ modBpsk50percent(1),
+ modQpsk50percentSingle(2),
+ modQpsk75percentSingle(3),
+ mod16qam50percentSingle(4),
+ mod16qam75percentSingle(5),
+ mod64qam67percentSingle(6),
+ mod64qam83percentSingle(7),
+ modReserved1(8),
+ modQpsk50percentDual(9),
+ modQpsk75percentDual(10),
+ mod16qam50percentDual(11),
+ mod16qam75percentDual(12),
+ mod64qam67percentDual(13),
+ mod64qam83percentDual(14),
+ modReserved2(15)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Current active transmit modulation mode"
+ ::= { phyStatus 9 }
+
+ receiveFreqMHz OBJECT-TYPE
+ SYNTAX INTEGER (0..5925)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Current receive frequency expressed in integer MHz"
+ ::= { phyStatus 11 }
+
+ transmitFreqMHz OBJECT-TYPE
+ SYNTAX INTEGER (0..5925)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Current transmit frequency expressed in integer MHz"
+ ::= { phyStatus 12 }
+
+ signalStrengthRatio OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Signal strength ratio (Vertical / Horizontal) : the
+ number of dB larger the Vertical antenna input is than
+ the Horizontal antenna input expressed in tenths of a dB"
+ ::= { phyStatus 13 }
+
+ receiveFreqKHz OBJECT-TYPE
+ SYNTAX INTEGER (0..5925000)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Current receive frequency expressed as KHz"
+ ::= { phyStatus 14 }
+
+ transmitFreqKHz OBJECT-TYPE
+ SYNTAX INTEGER (0..5925000)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Current transmit frequency expressed as KHz"
+ ::= { phyStatus 15 }
+
+ searchState OBJECT-TYPE
+ SYNTAX INTEGER {
+ registering(0),
+ searching(1),
+ acquiring(2),
+ registeringAcquiring2(3)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Search status of the wireless modem. 'Registering' means
+ that the modem has locked to an OFDM signal, and the
+ wireless link is up. 'Searching' means that no wireless
+ signal has been detected. 'Acquiring' means that a
+ wireless signal has been detected, but the modem has not
+ locked to an OFDM signal."
+ ::= { phyStatus 16 }
+
+ -- Alarms group attribute definitions
+ --
+ unitOutOfCalibration OBJECT-TYPE
+ SYNTAX INTEGER {
+ calibrated(0),
+ partialCalibration(1),
+ invalidCalibration(2),
+ bandwidthvariantunsupportedPAsShutdown(3),
+ outOfCalibrationPAsShutdown(4)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The unit is out of calibration"
+ ::= { alarms 1 }
+
+ incompatibleRegionCodes OBJECT-TYPE
+ SYNTAX INTEGER {
+ ok(0),
+ incompatibleLicenceKeys(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The master and slave units have incompatible region
+ codes. NB: Both units must have compatible licence keys"
+ ::= { alarms 4 }
+
+ noWirelessChannelAvailable OBJECT-TYPE
+ SYNTAX INTEGER {
+ ok(0),
+ noWirelessChannelAvailable(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Spectrum Management was unable to locate a suitable
+ wireless channel to operate on"
+ ::= { alarms 5 }
+
+ wirelessLinkDisabledWarning OBJECT-TYPE
+ SYNTAX INTEGER {
+ ok(0),
+ disabledBySNMPifAdminStatus(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The SNMP ifAdminStatus of the wireless interface has
+ disabled wireless traffic"
+ ::= { alarms 6 }
+
+ dataPortDisabledWarning OBJECT-TYPE
+ SYNTAX INTEGER {
+ ok(0),
+ disabledBySNMPifAdminStatus(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The SNMP ifAdminStatus of the Ethernet interface has
+ disabled Ethernet traffic"
+ ::= { alarms 7 }
+
+ dataPortConfigurationMismatch OBJECT-TYPE
+ SYNTAX INTEGER {
+ noError(0),
+ mismatchDetected(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The detection of Ethernet fragments (runt packets) when
+ the link is in full duplex is an indication of an
+ auto-negotiation or forced configuration mismatch"
+ ::= { alarms 9 }
+
+ incompatibleMasterAndSlave OBJECT-TYPE
+ SYNTAX INTEGER {
+ ok(0),
+ incompatibleProductVariants(1),
+ differentSoftwareVersionsRunning(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "A non-zero value indicates that the master and slave
+ ends of a link are different hardware products, or have
+ different software versions. NB: It is very unusual to
+ detect this, because incompatible units will normally
+ fail to establish a wireless link. However, some
+ combinations may establish a partial wireless link and
+ detect this situation. NB: A non-zero value may generate
+ an SNMP trap and/or SMTP email alert"
+ ::= { alarms 10 }
+
+ tDDSynchronizationStatus OBJECT-TYPE
+ SYNTAX INTEGER {
+ locked(0),
+ holdover(1),
+ holdoverNotConnected(2),
+ acquiringLock(3),
+ noTimingReference(4),
+ timingSystemNotConnected(5),
+ initialising(6),
+ clusterTimingMaster(7),
+ tDDSyncNotActive(8)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "An alarm value (displayed in red) indicates that one of
+ the following conditions has not been met (i) An external
+ timing system is connected or internal timing has been
+ configured. (ii) The timing system is providing a useable
+ reference. (iii) The ODU is locked to this reference."
+ ::= { alarms 11 }
+
+ tDDSynchronizationAlarm OBJECT-TYPE
+ SYNTAX INTEGER {
+ ok(0),
+ notSynchronized(1),
+ timingSystemFailure(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Not Synchronized indicates failure of the external
+ timing system for a period greater than the holdover
+ timer. TDD frame timing will have drifted, and this link
+ may cause interference with other links in a synchronized
+ network. Timing System Failure is an early warning,
+ indicating that 80% of the holdover period has expired."
+ ::= { alarms 13 }
+
+ linkModeOptimizationMismatch OBJECT-TYPE
+ SYNTAX INTEGER {
+ ok(0),
+ linkModeOptimizationMismatch(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The remote node of this link has been configured with a
+ different link mode optimization"
+ ::= { alarms 14 }
+
+ capacityLicenseMismatch OBJECT-TYPE
+ SYNTAX INTEGER {
+ ok(0),
+ mismatchDetected(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The local and remote units have different licensed
+ capacity and/or the full capacity trial has been
+ activated at only one unit. The wireless link is
+ operating at the capacity of the lowest capacity unit"
+ ::= { alarms 16 }
+
+ -- Smtp group attribute definitions
+ --
+ sMTPEmailAlert OBJECT-TYPE
+ SYNTAX INTEGER {
+ disabled(0),
+ enabled(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Simple Mail Transfer Protocol is used to send equipment
+ alerts via email to a specified email address. This
+ utility can only be configured by the system
+ administrator"
+ ::= { smtp 1 }
+
+ sMTPServerIPAddress OBJECT-TYPE
+ SYNTAX IpAddress
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "IP address of the SMTP server"
+ ::= { smtp 2 }
+
+ sMTPServerPortNumber OBJECT-TYPE
+ SYNTAX INTEGER (0..65535)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Port number of the SMTP server"
+ ::= { smtp 3 }
+
+ sMTPSourceEmailAddress OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..63))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The 'from' email address used when constructing the
+ automatically generated e-mail message"
+ ::= { smtp 4 }
+
+ sMTPDestinationEmailAddress OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..63))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The 'to' email address used when constructing the
+ automatically generated e-mail message"
+ ::= { smtp 5 }
+
+ sMTPEnabledMessages OBJECT-TYPE
+ SYNTAX BITS {
+ telecomsChannelUpDown(1),
+ unknown6(2),
+ dataPortUpDown(3),
+ enabledDiagnosticAlarms(4),
+ dFSImpulseInterference(5),
+ channelChange(6),
+ wirelessLinkUpDown(7)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This controls which SMTP messages the unit will send"
+ ::= { smtp 6 }
+
+ -- SnmpControl group attribute definitions
+ --
+ sNMPPortNumber OBJECT-TYPE
+ SYNTAX INTEGER (0..65535)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The IP port number used to access the SNMP MIB (i.e.
+ Gets and Sets) (default = 161). NB: A system reboot is
+ required to activate changes to this attribute"
+ ::= { snmpControl 1 }
+
+ sNMPCommunityString OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..63))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The SNMP community string. NB: A system reboot is
+ required to activate changes to this attribute"
+ ::= { snmpControl 2 }
+
+ sNMPTrapTableNumber OBJECT-TYPE
+ SYNTAX INTEGER (2)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Number of entries in the sNMPTrapTable."
+ ::= { snmpControl 3 }
+
+ sNMPTrapVersion OBJECT-TYPE
+ SYNTAX INTEGER {
+ v1(0),
+ v2c(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The SNMP protocol version to use for SNMP Traps. NB: A
+ system reboot is required to activate changes to this
+ attribute"
+ ::= { snmpControl 5 }
+
+ sNMPEnabledTraps OBJECT-TYPE
+ SYNTAX BITS {
+ unknown8(0),
+ dataPortUpDown(1),
+ authenticationFailure(2),
+ enabledDiagnosticAlarms(3),
+ dFSImpulseInterference(4),
+ channelChange(5),
+ wirelessLinkUpDown(6),
+ coldStart(7),
+ telecomsChannelUpDown(15)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This controls which SNMP Traps the unit will send"
+ ::= { snmpControl 6 }
+
+ enabledDiagnosticAlarms OBJECT-TYPE
+ SYNTAX BITS {
+ incompatibleMasterAndSlave(0),
+ incompatibleRegionCodes(1),
+ unknown6(2),
+ unknown5(3),
+ unitOutOfCalibration(4),
+ installArmState(5),
+ installStatus(6),
+ regionCode(7),
+ telecomsChannelStatus(8),
+ unknown15(9),
+ dataPortStatus(10),
+ dataPortDisabledWarning(11),
+ wirelessLinkDisabledWarning(12),
+ sNTPSynchronizationFailed(13),
+ noWirelessChannelAvailable(14),
+ dataPortConfigurationMismatch(15),
+ syslogClientDisabledWarning(16),
+ licensedCapacityMismatch(17),
+ syslogLocalWrapped(18),
+ syslogLocalNearlyFull(19),
+ syslogLocalEnableDisable(20),
+ linkModeOptimizationMismatch(21),
+ tDDSynchronizationAlarm(22),
+ telecomsChannelLoopback(23)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Controls which individual diagnostic alarms are enabled.
+ The unit may be configured to generate SNMP traps and/or
+ SMTP email alerts for these enabled alarms by selecting
+ 'Enabled Diagnostic Alarms' on the 'SNMP Enabled Traps'
+ and/or 'SMTP Enabled Messages' attributes"
+ ::= { snmpControl 7 }
+
+ sNMPSendAllTrapsAtStartup OBJECT-TYPE
+ SYNTAX INTEGER {
+ disabled(0),
+ enabled(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Controls whether cleared traps are reported at start-up
+ as well as raised traps. Only enabled traps will be
+ reported. NB: Traps corresponding to transient events
+ (i.e. not associated with an alarm or status value) are
+ only sent when required and not at start-up."
+ ::= { snmpControl 8 }
+
+ -- SNMPTrapTable group attribute definitions
+ --
+ sNMPTrapTableIndex OBJECT-TYPE
+ SYNTAX INTEGER (1..2)
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "SNMP trap value, used to index the SNMPTrapTable."
+ ::= { sNMPTrapTableEntry 1 }
+
+ sNMPTrapIPAddress OBJECT-TYPE
+ SYNTAX IpAddress
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The IP address to which all SNMP Traps are sent. An IP
+ Address of 0.0.0.0 disables all TRAP generation. NB: A
+ system reboot is required to activate changes to this
+ attribute."
+ ::= { sNMPTrapTableEntry 2 }
+
+ sNMPTrapPortNumber OBJECT-TYPE
+ SYNTAX INTEGER (0..65535)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Destination port for SNMP Traps (default=162). A value
+ of 0 will disable the trap receiver. NB: A system reboot
+ is required to activate changes to this attribute."
+ ::= { sNMPTrapTableEntry 3 }
+
+ -- Sntp group attribute definitions
+ --
+ sNTPState OBJECT-TYPE
+ SYNTAX INTEGER {
+ disabled(0),
+ enabled(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "SNTP control state"
+ ::= { sntp 1 }
+
+ sNTPServerIPAddress OBJECT-TYPE
+ SYNTAX IpAddress
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The IP address of a valid SNTP server"
+ ::= { sntp 2 }
+
+ sNTPServerPortNumber OBJECT-TYPE
+ SYNTAX INTEGER (0..65535)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The IP port number of the SNTP server. Defaults to port
+ 123."
+ ::= { sntp 3 }
+
+ sNTPPollInterval OBJECT-TYPE
+ SYNTAX INTEGER (60..43200)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The SNTP server polling interval"
+ ::= { sntp 4 }
+
+ sNTPSync OBJECT-TYPE
+ SYNTAX INTEGER {
+ noSync(0),
+ inSync(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "If SNTP Sync fails then check the server settings in the
+ Remote Management page, or disable SNTP. NB: a change of
+ state may generate an SNMP trap and/or SMTP email alert"
+ ::= { sntp 5 }
+
+ sNTPLastSync OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Last SNTP sync time"
+ ::= { sntp 6 }
+
+ systemClock OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "System clock presented as local time"
+ ::= { sntp 7 }
+
+ timeZone OBJECT-TYPE
+ SYNTAX INTEGER {
+ gmtMinus1200(0),
+ gmtMinus1130(1),
+ gmtMinus1100(2),
+ gmtMinus1030(3),
+ gmtMinus1000(4),
+ gmtMinus0930(5),
+ gmtMinus0900(6),
+ gmtMinus0830(7),
+ gmtMinus0800(8),
+ gmtMinus0730(9),
+ gmtMinus0700(10),
+ gmtMinus0630(11),
+ gmtMinus0600(12),
+ gmtMinus0530(13),
+ gmtMinus0500(14),
+ gmtMinus0430(15),
+ gmtMinus0400(16),
+ gmtMinus0330(17),
+ gmtMinus0300(18),
+ gmtMinus0230(19),
+ gmtMinus0200(20),
+ gmtMinus0130(21),
+ gmtMinus0100(22),
+ gmtMinus0030(23),
+ gmtZero(24),
+ gmtPlus0030(25),
+ gmtPlus0100(26),
+ gmtPlus0130(27),
+ gmtPlus0200(28),
+ gmtPlus0230(29),
+ gmtPlus0300(30),
+ gmtPlus0330(31),
+ gmtPlus0400(32),
+ gmtPlus0430(33),
+ gmtPlus0500(34),
+ gmtPlus0530(35),
+ gmtPlus0600(36),
+ gmtPlus0630(37),
+ gmtPlus0700(38),
+ gmtPlus0730(39),
+ gmtPlus0800(40),
+ gmtPlus0830(41),
+ gmtPlus0900(42),
+ gmtPlus0930(43),
+ gmtPlus1000(44),
+ gmtPlus1030(45),
+ gmtPlus1100(46),
+ gmtPlus1130(47),
+ gmtPlus1200(48),
+ gmtPlus1230(49),
+ gmtPlus1300(50)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Time zone offsets from Greenwich Mean Time (GMT)"
+ ::= { sntp 8 }
+
+ daylightSaving OBJECT-TYPE
+ SYNTAX INTEGER {
+ disabled(0),
+ enabled(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Daylight Saving Time"
+ ::= { sntp 9 }
+
+ -- Reset group attribute definitions
+ --
+ systemReset OBJECT-TYPE
+ SYNTAX INTEGER {
+ running(0),
+ consoleReboot(1)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Setting this attribute to '1' will cause a system
+ reboot. NB: a system reboot will apply any pending new
+ settings held in memory"
+ ::= { reset 1 }
+
+ -- Versions group attribute definitions
+ --
+ softwareVersion OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..63))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Current software version"
+ ::= { versions 1 }
+
+ hardwareVersion OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..63))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Hardware platform version"
+ ::= { versions 2 }
+
+ secondarySoftwareVersion OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..63))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Secondary software version, used when the primary
+ software image is invalid or erased"
+ ::= { versions 3 }
+
+ bootVersion OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..63))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Boot code software version"
+ ::= { versions 4 }
+
+ -- PubStats group attribute definitions
+ --
+ receiveDataRate OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Average data rate over the last one second interval
+ (kbps)"
+ ::= { pubStats 1 }
+
+ transmitDataRate OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Average data rate over the last one second interval
+ (kbps)"
+ ::= { pubStats 2 }
+
+ aggregateDataRate OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Average data rate over the last one second interval
+ (kbps)"
+ ::= { pubStats 3 }
+
+ wirelessLinkAvailability OBJECT-TYPE
+ SYNTAX INTEGER (0..1000000)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Link availability calculated since the last reset of the
+ system counters, as a percentage multiplied by 10000 to
+ give four decimal places of precision"
+ ::= { pubStats 4 }
+
+ wirelessLinkStatus OBJECT-TYPE
+ SYNTAX INTEGER {
+ up(0),
+ registering(1),
+ acquiring(2),
+ searching(3),
+ radarCAC(4),
+ initialising(5)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Current status of the wireless link"
+ ::= { pubStats 5 }
+
+ byteErrorRatio OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Reciprocal of the byte error ratio calculated since the
+ last reset of the system counters"
+ ::= { pubStats 6 }
+
+ receiveModulationModeDetail OBJECT-TYPE
+ SYNTAX INTEGER {
+ runningAtMaximumReceiveMode(0),
+ runningAtUserConfiguredMaxModulationMode(1),
+ restrictedBecauseInstallationIsArmed(2),
+ restrictedBecauseOfByteErrorsOnTheWirelessLink(3),
+ restrictedBecauseTheLinkParametersAreUpdating(4),
+ restrictedBecauseChannelChangeIsInProgress(5),
+ restrictedDueToTheLowEthernetLinkSpeed(6),
+ runningAtMaximumReceiveModeForChannelBandwidth(7),
+ limitedByTheWirelessConditions(8)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The reason for the current receive modulation mode"
+ ::= { pubStats 7 }
+
+ -- Encryption group attribute definitions
+ --
+ encryptionAlgorithm OBJECT-TYPE
+ SYNTAX INTEGER {
+ none(0),
+ aESRijndael(1),
+ aES256bitRijndael(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The Encryption Algorithm used by the wireless link. NB:
+ A system reboot is required to activate changes to this
+ attribute. NB: The same Encryption Algorithm must be
+ configured at BOTH ends of the link for it to function
+ correctly"
+ ::= { encryption 1 }
+
+ -- TDDControl group attribute definitions
+ --
+ tDDSynchronizationMode OBJECT-TYPE
+ SYNTAX INTEGER {
+ disabled(0),
+ enabled(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "TDD Synchronization Mode selection"
+ ::= { tDDControl 1 }
+
+ -- AAAControl group attribute definitions
+ --
+ userTableNumber OBJECT-TYPE
+ SYNTAX INTEGER (1..10)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Number of entries in the userTable"
+ ::= { aAAControl 1 }
+
+ -- UserTable group attribute definitions
+ --
+ userTableIndex OBJECT-TYPE
+ SYNTAX INTEGER (1..10)
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "used to index values in the userTable."
+ ::= { userTableEntry 1 }
+
+ userName OBJECT-TYPE
+ SYNTAX OCTET STRING
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "User name which must be entered, along with the
+ appropriate password, in order to gain access to the
+ system."
+ ::= { userTableEntry 2 }
+
+ userRole OBJECT-TYPE
+ SYNTAX INTEGER {
+ readOnly(0),
+ systemAdministrator(1),
+ securityOfficer(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Role of the selected user. A Security Officer has access
+ to and can modify all settings. A System Administrator
+ has access to and can modify all non-security settings. A
+ Read Only user can view settings, but cannot make any
+ changes."
+ ::= { userTableEntry 3 }
+
+ userEnabled OBJECT-TYPE
+ SYNTAX INTEGER {
+ disabled(0),
+ enabled(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Enable / Disable the selected user"
+ ::= { userTableEntry 4 }
+
+ userPassword OBJECT-TYPE
+ SYNTAX OCTET STRING
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "User password, which must be entered in order to gain
+ access to the system."
+ ::= { userTableEntry 5 }
+
+ -- SyslogControl group attribute definitions
+ --
+ syslogClient OBJECT-TYPE
+ SYNTAX INTEGER {
+ disabled(0),
+ enabled(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Enable or disable the syslog client"
+ ::= { syslogControl 1 }
+
+ syslogState OBJECT-TYPE
+ SYNTAX INTEGER {
+ disabled(0),
+ enabled(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The syslog service has been enabled or disabled"
+ ::= { syslogControl 2 }
+
+ -- Supplementary group attribute definitions
+ --
+ longitude OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..19))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The longitude of the unit, measured in decimal degrees.
+ This object is set by the SNMP manager and has no
+ internal function."
+ ::= { supplementary 1 }
+
+ latitude OBJECT-TYPE
+ SYNTAX DisplayString (SIZE(0..19))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The latitude of the unit, measured in decimal degrees.
+ This object is set by the SNMP manager and has no
+ internal function."
+ ::= { supplementary 2 }
+
+ altitude OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The altitude of the unit, measured in metres. This
+ object is set by the SNMP manager and has no internal
+ function."
+ ::= { supplementary 3 }
+
+ -- Enterprise NOTIFICATION definitions
+ --
+
+ channelChangeTrap NOTIFICATION-TYPE
+ OBJECTS { receiveChannel }
+ STATUS current
+ DESCRIPTION "The PTP radio has changed wireless channel.
+ This has been caused by either
+ i) mandatory radar avoidance,
+ a DFS impulsive interference event will also be
+ detected,
+ or
+ ii) Dynamic Spectrum Optimization, (DSO)
+ DSO improves link performance by selecting the
+ most appropriate transmit and receive channels
+ with the lowest level of interference."
+ ::= { ptpTrapPrefix 1 }
+
+ dfsImpulsiveInterferenceTrap NOTIFICATION-TYPE
+ OBJECTS { receiveChannel }
+ STATUS current
+ DESCRIPTION "DFS impulsive interference detected event"
+ ::= { ptpTrapPrefix 2 }
+
+ dataPortStatusTrap NOTIFICATION-TYPE
+ OBJECTS { dataPortStatus }
+ STATUS current
+ DESCRIPTION
+ "Current status of the Ethernet link. NB: a change of
+ state may generate an SNMP trap and/or SMTP email alert"
+ ::= { ptpTrapPrefix 3 }
+
+ telecomsChannelStatusTrap NOTIFICATION-TYPE
+ OBJECTS { telecomsChannelStatus }
+ STATUS current
+ DESCRIPTION
+ "Current status of telecoms channel. NB: a change of
+ state may generate an SNMP trap and/or SMTP email alert"
+ ::= { ptpTrapPrefix 4 }
+
+ telecomsLoopbackTrap NOTIFICATION-TYPE
+ OBJECTS { telecomsLoopback }
+ STATUS current
+ DESCRIPTION
+ "The loopback status of telecoms channel. This is
+ intended for installation testing and should be set to
+ 'None' for normal operation. The wire connections to a
+ unit can be tested by applying a 'Copper' loopback to the
+ local unit. The wireless connection to the remote unit
+ can be tested by applying a 'Wireless' loopback to the
+ remote unit with no loopback on the local unit. When
+ applying a wireless loopback, please ensure that the
+ other end of the link has a loopback setting of 'None'.
+ NB: a change of state may generate an SNMP trap and/or
+ SMTP email alert"
+ ::= { ptpTrapPrefix 6 }
+
+ regionCodeTrap NOTIFICATION-TYPE
+ OBJECTS { regionCode }
+ STATUS current
+ DESCRIPTION
+ "The region code prohibits the wireless unit from
+ operating outside the regulated limits. An invalid region
+ code indicates a corrupted licence key. NB: a change of
+ state may generate an SNMP trap and/or SMTP email alert"
+ ::= { ptpTrapPrefix 8 }
+
+ installStatusTrap NOTIFICATION-TYPE
+ OBJECTS { installStatus }
+ STATUS current
+ DESCRIPTION
+ "A non-zero value indicates that signalling was received
+ with the wrong MAC address or a mismatched link name. NB:
+ It is very unusual to detect this, because units with
+ mis-configured Target MAC Address will normally fail to
+ establish a wireless link. However, rare circumstances
+ may establish a partial wireless link and detect this
+ situation. NB: A non-zero value on start-up, or a change
+ of value during operation, may generate an SNMP trap
+ and/or SMTP email alert"
+ ::= { ptpTrapPrefix 9 }
+
+ installArmStateTrap NOTIFICATION-TYPE
+ OBJECTS { installArmState }
+ STATUS current
+ DESCRIPTION
+ "Indicates if the unit is being installed. NB: a value
+ other than 'disarmed' on startup, or a change of state
+ during operation may generate an SNMP trap and/or SMTP
+ email alert"
+ ::= { ptpTrapPrefix 10 }
+
+ unitOutOfCalibrationTrap NOTIFICATION-TYPE
+ OBJECTS { unitOutOfCalibration }
+ STATUS current
+ DESCRIPTION
+ "The unit is out of calibration"
+ ::= { ptpTrapPrefix 11 }
+
+ incompatibleRegionCodesTrap NOTIFICATION-TYPE
+ OBJECTS { incompatibleRegionCodes }
+ STATUS current
+ DESCRIPTION
+ "The master and slave units have incompatible region
+ codes. NB: Both units must have compatible licence keys"
+ ::= { ptpTrapPrefix 14 }
+
+ noWirelessChannelAvailableTrap NOTIFICATION-TYPE
+ OBJECTS { noWirelessChannelAvailable }
+ STATUS current
+ DESCRIPTION
+ "Spectrum Management was unable to locate a suitable
+ wireless channel to operate on"
+ ::= { ptpTrapPrefix 15 }
+
+ wirelessLinkDisabledWarningTrap NOTIFICATION-TYPE
+ OBJECTS { wirelessLinkDisabledWarning }
+ STATUS current
+ DESCRIPTION
+ "The SNMP ifAdminStatus of the wireless interface has
+ disabled wireless traffic"
+ ::= { ptpTrapPrefix 16 }
+
+ dataPortDisabledWarningTrap NOTIFICATION-TYPE
+ OBJECTS { dataPortDisabledWarning }
+ STATUS current
+ DESCRIPTION
+ "The SNMP ifAdminStatus of the Ethernet interface has
+ disabled Ethernet traffic"
+ ::= { ptpTrapPrefix 17 }
+
+ dataPortConfigurationMismatchTrap NOTIFICATION-TYPE
+ OBJECTS { dataPortConfigurationMismatch }
+ STATUS current
+ DESCRIPTION
+ "The detection of Ethernet fragments (runt packets) when
+ the link is in full duplex is an indication of an
+ auto-negotiation or forced configuration mismatch"
+ ::= { ptpTrapPrefix 19 }
+
+ incompatibleMasterAndSlaveTrap NOTIFICATION-TYPE
+ OBJECTS { incompatibleMasterAndSlave }
+ STATUS current
+ DESCRIPTION
+ "A non-zero value indicates that the master and slave
+ ends of a link are different hardware products, or have
+ different software versions. NB: It is very unusual to
+ detect this, because incompatible units will normally
+ fail to establish a wireless link. However, some
+ combinations may establish a partial wireless link and
+ detect this situation. NB: A non-zero value may generate
+ an SNMP trap and/or SMTP email alert"
+ ::= { ptpTrapPrefix 20 }
+
+ sNTPSyncTrap NOTIFICATION-TYPE
+ OBJECTS { sNTPSync }
+ STATUS current
+ DESCRIPTION
+ "If SNTP Sync fails then check the server settings in the
+ Remote Management page, or disable SNTP. NB: a change of
+ state may generate an SNMP trap and/or SMTP email alert"
+ ::= { ptpTrapPrefix 21 }
+
+ tDDSynchronizationAlarmTrap NOTIFICATION-TYPE
+ OBJECTS { tDDSynchronizationAlarm }
+ STATUS current
+ DESCRIPTION
+ "Not Synchronized indicates failure of the external
+ timing system for a period greater than the holdover
+ timer. TDD frame timing will have drifted, and this link
+ may cause interference with other links in a synchronized
+ network. Timing System Failure is an early warning,
+ indicating that 80% of the holdover period has expired."
+ ::= { ptpTrapPrefix 22 }
+
+ linkModeOptimizationMismatchTrap NOTIFICATION-TYPE
+ OBJECTS { linkModeOptimizationMismatch }
+ STATUS current
+ DESCRIPTION
+ "The remote node of this link has been configured with a
+ different link mode optimization"
+ ::= { ptpTrapPrefix 25 }
+
+ capacityLicenseMismatchTrap NOTIFICATION-TYPE
+ OBJECTS { capacityLicenseMismatch }
+ STATUS current
+ DESCRIPTION
+ "The local and remote units have different licensed
+ capacity and/or the full capacity trial has been
+ activated at only one unit. The wireless link is
+ operating at the capacity of the lowest capacity unit"
+ ::= { ptpTrapPrefix 27 }
+
+ syslogStateTrap NOTIFICATION-TYPE
+ OBJECTS { syslogState }
+ STATUS current
+ DESCRIPTION
+ "The syslog service has been enabled or disabled"
+ ::= { ptpTrapPrefix 30 }
+
+ syslogLocalNearlyFullTrap NOTIFICATION-TYPE
+ STATUS current
+ DESCRIPTION "The syslog local log is nearly full (90%)"
+ ::= { ptpTrapPrefix 31 }
+
+ syslogLocalWrappedTrap NOTIFICATION-TYPE
+ STATUS current
+ DESCRIPTION "The syslog local log has wrapped"
+ ::= { ptpTrapPrefix 32 }
+
+ syslogClientTrap NOTIFICATION-TYPE
+ OBJECTS { syslogClient }
+ STATUS current
+ DESCRIPTION
+ "Enable or disable the syslog client"
+ ::= { ptpTrapPrefix 33 }
+
+ END
|