diff options
Diffstat (limited to 'MIBS/ADSL2-LINE-TC-MIB')
| -rw-r--r-- | MIBS/ADSL2-LINE-TC-MIB | 728 |
1 files changed, 728 insertions, 0 deletions
diff --git a/MIBS/ADSL2-LINE-TC-MIB b/MIBS/ADSL2-LINE-TC-MIB new file mode 100644 index 0000000..19681fc --- /dev/null +++ b/MIBS/ADSL2-LINE-TC-MIB @@ -0,0 +1,728 @@ +ADSL2-LINE-TC-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+ MODULE-IDENTITY,
+ transmission
+ FROM SNMPv2-SMI
+ TEXTUAL-CONVENTION
+ FROM SNMPv2-TC;
+
+
+adsl2TCMIB MODULE-IDENTITY
+ LAST-UPDATED "200610040000Z"
+ ORGANIZATION "ADSLMIB Working Group"
+ CONTACT-INFO
+ "WG-email: adslmib@ietf.org
+ Info: https://www1.ietf.org/mailman/listinfo/adslmib
+
+ Chair: Mike Sneed
+ Sand Channel Systems
+ Postal: P.O. Box 37324
+ Raleigh NC 27627-732
+ Email: sneedmike@hotmail.com
+ Phone: +1 206 600 7022
+
+ Co-Chair & Co-editor:
+ Menachem Dodge
+ ECI Telecom Ltd.
+ Postal: 30 Hasivim St.
+ Petach Tikva 49517,
+ Israel.
+ Email: mbdodge@ieee.org
+ Phone: +972 3 926 8421
+ Co-editor: Moti Morgenstern
+ ECI Telecom Ltd.
+ Postal: 30 Hasivim St.
+ Petach Tikva 49517,
+ Israel.
+ Email: moti.morgenstern@ecitele.com
+ Phone: +972 3 926 6258
+
+ Co-editor: Scott Baillie
+ NEC Australia
+ Postal: 649-655 Springvale Road,
+ Mulgrave, Victoria 3170,
+ Australia.
+ Email: scott.baillie@nec.com.au
+ Phone: +61 3 9264 3986
+
+ Co-editor: Umberto Bonollo
+ NEC Australia
+ Postal: 649-655 Springvale Road,
+ Mulgrave, Victoria 3170,
+ Australia.
+ Email: umberto.bonollo@nec.com.au
+ Phone: +61 3 9264 3385"
+ DESCRIPTION
+ "This MIB Module provides Textual Conventions to be
+ used by the ADSL2-LINE-MIB module for the purpose of
+ managing ADSL, ADSL2, and ADSL2+ lines.
+
+ Copyright (C) The Internet Society (2006). This version of
+ this MIB module is part of RFC 4706: see the RFC itself for
+ full legal notices."
+ REVISION "200610040000Z"
+ DESCRIPTION
+ "Initial version, published as RFC 4706."
+ ::= { transmission 238 2 }
+
+
+
+-- adsl2MIB 2
+--
+-- ----------------------------------------------
+-- Textual Conventions --
+-- ----------------------------------------------
+
+Adsl2Unit ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Identifies a transceiver as being either an ATU-C or
+ an ATU-R. An ADSL line consists of two transceivers, an ATU-C
+ and an ATU-R. Attributes with this syntax reference the two
+ sides of a line. Specified as an INTEGER, the two values
+ are:
+
+ atuc(1) -- Central office ADSL terminal unit (ATU-C).
+ atur(2) -- Remote ADSL terminal unit (ATU-R)."
+ SYNTAX INTEGER {
+ atuc(1),
+ atur(2)
+ }
+
+Adsl2Direction ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Identifies the direction of a band as being
+ either upstream or downstream. Specified as an INTEGER,
+ the two values are:
+ upstream(1), and
+ downstream(2)."
+ SYNTAX INTEGER {
+ upstream(1),
+ downstream(2)
+ }
+
+Adsl2TransmissionModeType ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "A set of ADSL2 line transmission modes, with one bit
+ per mode. The notes (F) and (L) denote Full-Rate
+ and Lite/splitterless, respectively:
+ Bit 00 : Regional Std. (ANSI T1.413) (F)
+ Bit 01 : Regional Std. (ETSI DTS/TM06006) (F)
+ Bit 02 : G.992.1 POTS non-overlapped (F)
+ Bit 03 : G.992.1 POTS overlapped (F)
+ Bit 04 : G.992.1 ISDN non-overlapped (F)
+ Bit 05 : G.992.1 ISDN overlapped (F)
+ Bit 06 : G.992.1 TCM-ISDN non-overlapped (F)
+ Bit 07 : G.992.1 TCM-ISDN overlapped (F)
+ Bit 08 : G.992.2 POTS non-overlapped (L)
+ Bit 09 : G.992.2 POTS overlapped (L)
+ Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L)
+ Bit 11 : G.992.2 with TCM-ISDN overlapped (L)
+ Bit 12 : G.992.1 TCM-ISDN symmetric (F) -- not in G.997.1
+ Bit 13-17: Reserved
+ Bit 18 : G.992.3 POTS non-overlapped (F)
+ Bit 19 : G.992.3 POTS overlapped (F)
+ Bit 20 : G.992.3 ISDN non-overlapped (F)
+ Bit 21 : G.992.3 ISDN overlapped (F)
+ Bit 22-23: Reserved
+ Bit 24 : G.992.4 POTS non-overlapped (L)
+ Bit 25 : G.992.4 POTS overlapped (L)
+ Bit 26-27: Reserved
+ Bit 28 : G.992.3 Annex I All-Digital non-overlapped (F)
+ Bit 29 : G.992.3 Annex I All-Digital overlapped (F)
+ Bit 30 : G.992.3 Annex J All-Digital non-overlapped (F)
+ Bit 31 : G.992.3 Annex J All-Digital overlapped (F)
+ Bit 32 : G.992.4 Annex I All-Digital non-overlapped (L)
+ Bit 33 : G.992.4 Annex I All-Digital overlapped (L)
+ Bit 34 : G.992.3 Annex L POTS non-overlapped, mode 1,
+ wide U/S (F)
+ Bit 35 : G.992.3 Annex L POTS non-overlapped, mode 2,
+ narrow U/S(F)
+ Bit 36 : G.992.3 Annex L POTS overlapped, mode 3,
+ wide U/S (F)
+ Bit 37 : G.992.3 Annex L POTS overlapped, mode 4,
+ narrow U/S (F)
+ Bit 38 : G.992.3 Annex M POTS non-overlapped (F)
+ Bit 39 : G.992.3 Annex M POTS overlapped (F)
+ Bit 40 : G.992.5 POTS non-overlapped (F)
+ Bit 41 : G.992.5 POTS overlapped (F)
+ Bit 42 : G.992.5 ISDN non-overlapped (F)
+ Bit 43 : G.992.5 ISDN overlapped (F)
+ Bit 44-45: Reserved
+ Bit 46 : G.992.5 Annex I All-Digital non-overlapped (F)
+ Bit 47 : G.992.5 Annex I All-Digital overlapped (F)
+ Bit 48 : G.992.5 Annex J All-Digital non-overlapped (F)
+ Bit 49 : G.992.5 Annex J All-Digital overlapped (F)
+ Bit 50 : G.992.5 Annex M POTS non-overlapped (F)
+ Bit 51 : G.992.5 Annex M POTS overlapped (F)
+ Bit 52-55: Reserved"
+ SYNTAX BITS {
+ ansit1413(0),
+ etsi(1),
+ g9921PotsNonOverlapped(2),
+ g9921PotsOverlapped(3),
+ g9921IsdnNonOverlapped(4),
+ g9921isdnOverlapped(5),
+ g9921tcmIsdnNonOverlapped(6),
+ g9921tcmIsdnOverlapped(7),
+ g9922potsNonOverlapped(8),
+ g9922potsOverlapped(9),
+ g9922tcmIsdnNonOverlapped(10),
+ g9922tcmIsdnOverlapped(11),
+ g9921tcmIsdnSymmetric(12),
+ reserved1(13),
+ reserved2(14),
+ reserved3(15),
+ reserved4(16),
+ reserved5(17),
+ g9923PotsNonOverlapped(18),
+ g9923PotsOverlapped(19),
+ g9923IsdnNonOverlapped(20),
+ g9923isdnOverlapped(21),
+ reserved6(22),
+ reserved7(23),
+ g9924potsNonOverlapped(24),
+ g9924potsOverlapped(25),
+ reserved8(26),
+ reserved9(27),
+ g9923AnnexIAllDigNonOverlapped(28),
+ g9923AnnexIAllDigOverlapped(29),
+ g9923AnnexJAllDigNonOverlapped(30),
+ g9923AnnexJAllDigOverlapped(31),
+ g9924AnnexIAllDigNonOverlapped(32),
+ g9924AnnexIAllDigOverlapped(33),
+ g9923AnnexLMode1NonOverlapped(34),
+ g9923AnnexLMode2NonOverlapped(35),
+ g9923AnnexLMode3Overlapped(36),
+ g9923AnnexLMode4Overlapped(37),
+ g9923AnnexMPotsNonOverlapped(38),
+ g9923AnnexMPotsOverlapped(39),
+ g9925PotsNonOverlapped(40),
+ g9925PotsOverlapped(41),
+ g9925IsdnNonOverlapped(42),
+ g9925isdnOverlapped(43),
+ reserved10(44),
+ reserved11(45),
+ g9925AnnexIAllDigNonOverlapped(46),
+ g9925AnnexIAllDigOverlapped(47),
+ g9925AnnexJAllDigNonOverlapped(48),
+ g9925AnnexJAllDigOverlapped(49),
+ g9925AnnexMPotsNonOverlapped(50),
+ g9925AnnexMPotsOverlapped(51),
+ reserved12(52),
+ reserved13(53),
+ reserved14(54),
+ reserved15(55)
+ }
+
+Adsl2RaMode ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Specifies the rate adaptation behavior for the line.
+ The three possible behaviors are:
+ manual(1) - No Rate-Adaptation. The initialization
+ process attempts to synchronize to a
+ specified rate.
+ raInit(2) - Rate-Adaptation during initialization process
+ only, which attempts to synchronize to a rate
+ between minimum and maximum specified values.
+ dynamicRa(3) - Dynamic Rate-Adaptation during initialization
+ process as well as during SHOWTIME."
+ SYNTAX INTEGER {
+ manual(1),
+ raInit(2),
+ dynamicRa(3)
+ }
+
+Adsl2InitResult ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Specifies the result of a full initialization attempt; the
+ six possible result values are:
+ noFail(0) - Successful initialization.
+ configError(1) - Configuration failure.
+ configNotFeasible(2) - Configuration details not supported.
+ commFail(3) - Communication failure.
+ noPeerAtu(4) - Peer ATU not detected.
+ otherCause(5) - Other initialization failure reason.
+
+ The values used are as defined in ITU-T G.997.1,
+ paragraph 7.5.1.3"
+ SYNTAX INTEGER {
+ noFail(0),
+ configError(1),
+ configNotFeasible(2),
+ commFail(3),
+ noPeerAtu(4),
+ otherCause(5)
+ }
+
+Adsl2OperationModes ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "The ADSL2 management model specified includes an ADSL Mode
+ attribute that identifies an instance of ADSL Mode-Specific
+ PSD Configuration object in the ADSL Line Profile. The
+ following classes of ADSL operating mode are defined.
+ The notes (F) and (L) denote Full-Rate and Lite/splitterless
+ respectively:
+
+ +-------+--------------------------------------------------+
+ | Value | ADSL operation mode description |
+ +-------+--------------------------------------------------+
+
+ 1 - The default/generic PSD configuration. Default
+ configuration will be used when no other matching
+ mode-specific configuration can be found.
+ 2 - ADSL family. The attributes included in the Mode-
+ Specific PSD Configuration are irrelevant for
+ ITU-T G.992.1 and G.992.2 ADSL modes. Hence, it
+ is possible to map those modes to this generic
+ class.
+ 3-7 - Unused. Reserved for future ITU-T specification.
+ 8 - G.992.3 POTS non-overlapped (F)
+ 9 - G.992.3 POTS overlapped (F)
+ 10 - G.992.3 ISDN non-overlapped (F)
+ 11 - G.992.3 ISDN overlapped (F)
+ 12-13 - Unused. Reserved for future ITU-T specification.
+ 14 - G.992.4 POTS non-overlapped (L)
+ 15 - G.992.4 POTS overlapped (L)
+ 16-17 - Unused. Reserved for future ITU-T specification.
+ 18 - G.992.3 Annex I All-Digital non-overlapped (F)
+ 19 - G.992.3 Annex I All-Digital overlapped (F)
+ 20 - G.992.3 Annex J All-Digital non-overlapped (F)
+ 21 - G.992.3 Annex J All-Digital overlapped (F)
+ 22 - G.992.4 Annex I All-Digital non-overlapped (L)
+ 23 - G.992.4 Annex I All-Digital overlapped (L)
+ 24 - G.992.3 Annex L POTS non-overlapped, mode 1,
+ wide U/S (F)
+ 25 - G.992.3 Annex L POTS non-overlapped, mode 2,
+ narrow U/S(F)
+ 26 - G.992.3 Annex L POTS overlapped, mode 3,
+ wide U/S (F)
+ 27 - G.992.3 Annex L POTS overlapped, mode 4,
+ narrow U/S (F)
+ 28 - G.992.3 Annex M POTS non-overlapped (F)
+ 29 - G.992.3 Annex M POTS overlapped (F)
+ 30 - G.992.5 POTS non-overlapped (F)
+ 31 - G.992.5 POTS overlapped (F)
+ 32 - G.992.5 ISDN non-overlapped (F)
+ 33 - G.992.5 ISDN overlapped (F)
+ 34-35 - Unused. Reserved for future ITU-T specification.
+ 36 - G.992.5 Annex I All-Digital non-overlapped (F)
+ 37 - G.992.5 Annex I All-Digital overlapped (F)
+ 38 - G.992.5 Annex J All-Digital non-overlapped (F)
+ 39 - G.992.5 Annex J All-Digital overlapped (F)
+ 40 - G.992.5 Annex M POTS non-overlapped (F)
+ 41 - G.992.5 Annex M POTS overlapped (F)"
+ SYNTAX INTEGER {
+ defMode(1),
+ adsl(2),
+ g9923PotsNonOverlapped(8),
+ g9923PotsOverlapped(9),
+ g9923IsdnNonOverlapped(10),
+ g9923isdnOverlapped(11),
+ g9924potsNonOverlapped(14),
+ g9924potsOverlapped(15),
+ g9923AnnexIAllDigNonOverlapped(18),
+ g9923AnnexIAllDigOverlapped(19),
+ g9923AnnexJAllDigNonOverlapped(20),
+ g9923AnnexJAllDigOverlapped(21),
+ g9924AnnexIAllDigNonOverlapped(22),
+ g9924AnnexIAllDigOverlapped(23),
+ g9923AnnexLMode1NonOverlapped(24),
+ g9923AnnexLMode2NonOverlapped(25),
+ g9923AnnexLMode3Overlapped(26),
+ g9923AnnexLMode4Overlapped(27),
+ g9923AnnexMPotsNonOverlapped(28),
+ g9923AnnexMPotsOverlapped(29),
+ g9925PotsNonOverlapped(30),
+ g9925PotsOverlapped(31),
+ g9925IsdnNonOverlapped(32),
+ g9925isdnOverlapped(33),
+ g9925AnnexIAllDigNonOverlapped(36),
+ g9925AnnexIAllDigOverlapped(37),
+ g9925AnnexJAllDigNonOverlapped(38),
+ g9925AnnexJAllDigOverlapped(39),
+ g9925AnnexMPotsNonOverlapped(40),
+ g9925AnnexMPotsOverlapped(41)
+ }
+
+Adsl2PowerMngState ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Attributes with this syntax uniquely identify each power
+ management state defined for the ADSL/ADSL2 or ADSL2+ link.
+ The possible values are:
+ l0(1) - L0 - Full power management state.
+ l1(2) - L1 - Low power management state (for G.992.2).
+ l2(3) - L2 - Low power management state (for G.992.3,
+ G.992.4, and G.992.5).
+ l3(4) - L3 - Idle power management state."
+ SYNTAX INTEGER {
+ l0(1),
+ l1(2),
+ l2(3),
+ l3(4)
+ }
+
+Adsl2ConfPmsForce ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Attributes with this syntax are configuration parameters
+ that reference the desired power management state for the
+ ADSL/ADSL2 or ADSL2+ link:
+ l3toL0(0) - Perform a transition from L3 to L0
+ (Full power management state).
+ l0toL2(2) - Perform a transition from L0 to L2
+ (Low power management state).
+ l0orL2toL3(3) - Perform a transition into L3 (Idle
+ power management state).
+
+ The values used are as defined in ITU-T G.997.1,
+ paragraph 7.3.1.1.3"
+ SYNTAX INTEGER {
+ l3toL0(0),
+ l0toL2(2),
+ l0orL2toL3(3)
+ }
+
+Adsl2LConfProfPmMode ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Attributes with this syntax are configuration parameters
+ that reference the power modes/states into which the ATU-C or
+ ATU-R may autonomously transit.
+
+ It is a BITS structure that allows control of the following
+ transit options:
+ allowTransitionsToIdle(0) - XTU may autonomously transit
+ to idle (L3) state.
+ allowTransitionsToLowPower(1) - XTU may autonomously transit
+ to low-power (L2) state."
+ SYNTAX BITS {
+ allowTransitionsToIdle(0),
+ allowTransitionsToLowPower(1)
+ }
+
+Adsl2LineLdsf ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Attributes with this syntax are configuration parameters
+ that control the Loop Diagnostic mode for the ADSL/ADSL2 or
+ ADSL2+ link. The possible values are:
+ inhibit(0) - Inhibit Loop Diagnostic mode.
+ force(1) - Force/Initiate Loop Diagnostic mode.
+
+ The values used are as defined in ITU-T G.997.1,
+ paragraph 7.3.1.1.8"
+ SYNTAX INTEGER {
+ inhibit(0),
+ force(1)
+ }
+
+Adsl2LdsfResult ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Possible failure reasons associated with performing
+ a Dual Ended Loop Test (DELT) on a DSL line.
+ Possible values are:
+ none(1) - The default value in case LDSF was never
+ requested for the associated line.
+ success(2) - The recent command completed
+ successfully.
+ inProgress(3) - The Loop Diagnostics process is in
+ progress.
+ unsupported(4) - The NE or the line card doesn't support
+ LDSF.
+ cannotRun(5) - The NE cannot initiate the command, due
+ to a nonspecific reason.
+ aborted(6) - The Loop Diagnostics process aborted.
+ failed(7) - The Loop Diagnostics process failed.
+ illegalMode(8) - The NE cannot initiate the command, due
+ to the specific mode of the relevant
+ line.
+ adminUp(9) - The NE cannot initiate the command, as
+ the relevant line is administratively
+ 'Up'.
+ tableFull(10) - The NE cannot initiate the command, due
+ to reaching the maximum number of rows
+ in the results table.
+ noResources(11) - The NE cannot initiate the command, due
+ to lack of internal memory resources."
+ SYNTAX INTEGER {
+ none(1),
+ success(2),
+ inProgress(3),
+ unsupported(4),
+ cannotRun(5),
+ aborted(6),
+ failed(7),
+ illegalMode(8),
+ adminUp(9),
+ tableFull(10),
+ noResources(11)
+ }
+
+Adsl2SymbolProtection ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Attributes with this syntax are configuration parameters
+ that reference the minimum-length impulse noise protection
+ (INP) in terms of number of symbols. The possible values are:
+ noProtection (i.e., INP not required), halfSymbol (i.e., INP
+ length is 1/2 symbol), and 1-16 symbols in steps of 1 symbol."
+ SYNTAX INTEGER {
+ noProtection(1),
+ halfSymbol(2),
+ singleSymbol(3),
+ twoSymbols(4),
+ threeSymbols(5),
+ fourSymbols(6),
+ fiveSymbols(7),
+ sixSymbols(8),
+ sevenSymbols(9),
+ eightSymbols(10),
+ nineSymbols(11),
+ tenSymbols(12),
+ elevenSymbols(13),
+ twelveSymbols(14),
+ thirteeSymbols(15),
+ fourteenSymbols(16),
+ fifteenSymbols(17),
+ sixteenSymbols(18)
+ }
+
+Adsl2MaxBer ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Attributes with this syntax are configuration parameters
+ that reference the maximum Bit Error Rate (BER).
+ The possible values are:
+
+ eminus3(1) - Maximum BER=E^-3
+ eminus5(2) - Maximum BER=E^-5
+ eminus7(3) - Maximum BER=E^-7"
+ SYNTAX INTEGER {
+ eminus3(1),
+ eminus5(2),
+ eminus7(3)
+ }
+
+Adsl2ScMaskDs ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Each one of the 512 bits in this OCTET
+ STRING array represents the corresponding bin
+ in the downstream direction. A value of one
+ indicates that the bin is not in use."
+ SYNTAX OCTET STRING (SIZE (0..64))
+
+Adsl2ScMaskUs ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Each one of the 64 bits in this OCTET
+ STRING array represents the corresponding bin
+ in the upstream direction. A value of one
+ indicates that the bin is not in use."
+ SYNTAX OCTET STRING (SIZE (0..8))
+
+Adsl2RfiDs ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Each one of the 512 bits in this OCTET
+ STRING array represents the corresponding bin
+ in the downstream direction. A value of one
+ indicates that the bin is part of a notch
+ filter."
+ SYNTAX OCTET STRING (SIZE (0..64))
+
+Adsl2PsdMaskDs ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "This is a structure that represents up to
+ 32 PSD Mask breakpoints.
+ Each breakpoint occupies 3 octets: The first
+ two octets hold the index of the sub-carrier
+ associated with the breakpoint. The third octet
+ holds the PSD reduction at the breakpoint from 0
+ (0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of
+ 0.5 dBm/Hz."
+ SYNTAX OCTET STRING (SIZE (0..96))
+
+Adsl2PsdMaskUs ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "This is a structure that represents up to
+ 4 PSD Mask breakpoints.
+ Each breakpoint occupies 3 octets: The first
+ two octets hold the index of the sub-carrier
+ associated with the breakpoint. The third octet
+ holds the PSD reduction at the breakpoint from 0
+ (0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of
+ 0.5 dBm/Hz."
+ SYNTAX OCTET STRING (SIZE (0..12))
+
+Adsl2Tssi ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "This is a structure that represents up to
+ 32 transmit spectrum shaping (TSSi) breakpoints.
+ Each breakpoint occupies 3 octets: The first
+ two octets hold the index of the sub-carrier
+ associated with the breakpoint. The third octet
+ holds the shaping parameter at the breakpoint. It
+ is a value from 0 to 127 (units of -0.5 dB). The
+ special value 127 indicates that the sub-carrier
+ is not transmitted."
+ SYNTAX OCTET STRING (SIZE (0..96))
+
+Adsl2LastTransmittedState ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "This parameter represents the last successfully
+ transmitted initialization state in the last full
+ initialization performed on the line. States are
+ per the specific xDSL technology and are numbered
+ from 0 (if G.994.1 is used) or 1 (if G.994.1 is
+ not used) up to Showtime."
+ SYNTAX INTEGER {
+ atucG9941(0),
+ atucQuiet1(1),
+ atucComb1(2),
+ atucQuiet2(3),
+ atucComb2(4),
+ atucIcomb1(5),
+ atucLineprob(6),
+ atucQuiet3(7),
+ atucComb3(8),
+ atucIComb2(9),
+ atucMsgfmt(10),
+ atucMsgpcb(11),
+ atucQuiet4(12),
+ atucReverb1(13),
+ atucTref1(14),
+ atucReverb2(15),
+ atucEct(16),
+ atucReverb3(17),
+ atucTref2(18),
+ atucReverb4(19),
+ atucSegue1(20),
+ atucMsg1(21),
+ atucReverb5(22),
+ atucSegue2(23),
+ atucMedley(24),
+ atucExchmarker(25),
+ atucMsg2(26),
+ atucReverb6(27),
+ atucSegue3(28),
+ atucParams(29),
+ atucReverb7(30),
+ atucSegue4(31),
+ atucShowtime(32),
+ aturG9941(100),
+ aturQuiet1(101),
+ aturComb1(102),
+ aturQuiet2(103),
+ aturComb2(104),
+ aturIcomb1(105),
+ aturLineprob(106),
+ aturQuiet3(107),
+ aturComb3(108),
+ aturIcomb2(109),
+ aturMsgfmt(110),
+ aturMsgpcb(111),
+ aturReverb1(112),
+ aturQuiet4(113),
+ aturReverb2(114),
+ aturQuiet5(115),
+ aturReverb3(116),
+ aturEct(117),
+ aturReverb4(118),
+ aturSegue1(119),
+ aturReverb5(120),
+ aturSegue2(121),
+ aturMsg1(122),
+ aturMedley(123),
+ aturExchmarker(124),
+ aturMsg2(125),
+ aturReverb6(126),
+ aturSegue3(127),
+ aturParams(128),
+ aturReverb7(129),
+ aturSegue4(130),
+ aturShowtime(131)
+ }
+
+Adsl2LineStatus ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Attributes with this syntax are status parameters
+ that reflect the failure status for a given endpoint of
+ ADSL/ADSL2 or ADSL2+ link.
+
+ This BITS structure can report the following failures:
+
+ noDefect(0) - This bit position positively reports
+ that no defect or failure exists.
+ lossOfFrame(1) - Loss of frame synchronization.
+ lossOfSignal(2) - Loss of signal.
+ lossOfPower(3) - Loss of power. Usually this failure may
+ be reported for ATU-Rs only.
+ initFailure(4) - Recent initialization process failed.
+ Never active on ATU-R."
+ SYNTAX BITS {
+ noDefect(0),
+ lossOfFrame(1),
+ lossOfSignal(2),
+ lossOfPower(3),
+ initFailure(4)
+ }
+
+Adsl2ChAtmStatus ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Attributes with this syntax are status parameters that
+ reflect the failure status for Transmission Convergence (TC)
+ layer of a given ATM interface (data path over an ADSL/ADSL2
+ or ADSL2+ link).
+
+ This BITS structure can report the following failures:
+ noDefect(0) - This bit position positively
+ reports that no defect or failure
+ exists.
+ noCellDelineation(1) - The link was successfully
+ initialized, but cell delineation
+ was never acquired on the
+ associated ATM data path.
+ lossOfCellDelineation(2) - Loss of cell delineation on the
+ associated ATM data path."
+ SYNTAX BITS {
+ noDefect(0),
+ noCellDelineation(1),
+ lossOfCellDelineation(2)
+ }
+
+Adsl2ChPtmStatus ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Attributes with this syntax are status parameters that
+ reflect the failure status for a given PTM interface (packet
+ data path over an ADSL/ADSL2 or ADSL2+ link).
+
+ This BITS structure can report the following failures:
+ noDefect(0) - This bit position positively
+ reports that no defect or failure exists.
+ outOfSync(1) - Out of synchronization."
+ SYNTAX BITS {
+ noDefect(0),
+ outOfSync(1)
+ }
+
+END
+
+
+
|