Initial commitHEADmain

1 files changed, 7204 insertions, 0 deletions

diff --git a/MIBS/junos/JNX-OPT-IF-MIB b/MIBS/junos/JNX-OPT-IF-MIB
new file mode 100644
index 0000000..47b6cd4
--- /dev/null
+++ b/MIBS/junos/JNX-OPT-IF-MIB
@@ -0,0 +1,7204 @@
+JNX-OPT-IF-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+    MODULE-IDENTITY, OBJECT-TYPE, Gauge32, Integer32,
+    Unsigned32, transmission
+        FROM SNMPv2-SMI
+        TEXTUAL-CONVENTION, RowPointer, RowStatus, TruthValue
+        FROM SNMPv2-TC
+    SnmpAdminString
+        FROM SNMP-FRAMEWORK-MIB
+    MODULE-COMPLIANCE, OBJECT-GROUP
+        FROM SNMPv2-CONF
+    jnxoptIfMibRoot
+        FROM JUNIPER-SMI
+    ifIndex
+        FROM IF-MIB;
+
+
+--This is the MIB module for the OTN Interface objects. 
+
+
+jnxoptIfMibModule MODULE-IDENTITY 
+    LAST-UPDATED "200308130000Z" 
+    ORGANIZATION "IETF AToM MIB Working Group" 
+    CONTACT-INFO
+            "WG charter: 
+             http://www.ietf.org/html.charters/atommib-charter.html
+
+             Mailing Lists: 
+             General Discussion: atommib@research.telcordia.com 
+             To Subscribe: atommib-request@research.telcordia.com 
+             RFC 3591 Optical Interface Type MIB September 2003
+             Editor: Hing-Kam Lam
+             Postal: Lucent Technologies, Room 4C-616 
+                     101 Crawfords Corner Road 
+                     Holmdel, NJ 07733
+
+              Tel: +1 732 949 8338 
+             Email: hklam@lucent.com" 
+    DESCRIPTION 
+        "The MIB module to describe pre-OTN and OTN interfaces.
+         Copyright (C) The Internet Society (2003). This version 
+         of this MIB module is part of RFC 3591; see the RFC 
+         itself for full legal notices."
+
+    REVISION "200308130000Z" 
+    DESCRIPTION 
+        "Initial version, published as RFC 3591." 
+    ::={ jnxoptIfMibRoot 1 } 
+
+
+-- textual conventions 
+
+
+JnxoptIfAcTI ::= TEXTUAL-CONVENTION 
+    STATUS       current 
+    DESCRIPTION
+         "The trace identifier (TI) accepted at the receiver." 
+    SYNTAX       OCTET STRING (SIZE(64)) 
+
+
+JnxoptIfBitRateK ::= TEXTUAL-CONVENTION 
+    STATUS      current 
+    DESCRIPTION
+         "Indicates the index that is used to 
+          represent a supported bit rate and the different 
+          versions of OPUk, ODUk and OTUk. 
+          Allowed values of k are defined in ITU-T G.709. 
+          Currently allowed values in G.709 are:
+           k=1 represents an approximate bit rate of 2.5 Gbit/s, 
+          k=2 represents an approximate bit rate of 10 Gbit/s, 
+          k=3 represents an approximate bit rate of 40 Gbit/s."
+    SYNTAX      Integer32 
+
+JnxoptIfDEGM ::= TEXTUAL-CONVENTION 
+    STATUS      current 
+    DESCRIPTION
+      "Indicates the threshold level for declaring a Degraded Signal 
+      defect (dDEG). A dDEG shall be declared if JnxoptIfDEGM 
+      consecutive bad PM Seconds are detected."
+    SYNTAX      Unsigned32 (2..10) 
+
+
+JnxoptIfDEGThr ::= TEXTUAL-CONVENTION 
+    STATUS     current 
+    DESCRIPTION 
+      "Indicates the threshold level for declaring a performance 
+      monitoring (PM) Second to be bad. A PM Second is declared bad if 
+      the percentage of detected errored blocks in that second is 
+      greater than or equal to JnxoptIfDEGThr." 
+    SYNTAX     Unsigned32 (1..100) 
+
+
+JnxoptIfDirectionality ::= TEXTUAL-CONVENTION 
+    STATUS    current 
+    DESCRIPTION 
+      "Indicates the directionality of an entity." 
+    SYNTAX    INTEGER { 
+         sink(1), 
+         source(2), 
+         bidirectional(3) 
+    } 
+
+
+JnxoptIfSinkOrSource ::= TEXTUAL-CONVENTION 
+    STATUS    current 
+    DESCRIPTION 
+      "Indicates the directionality of an entity 
+      that is allowed only to be a source or sink." 
+    SYNTAX    INTEGER { 
+         sink(1), 
+         source(2) 
+    } 
+
+
+JnxoptIfExDAPI ::= TEXTUAL-CONVENTION 
+    STATUS current 
+    DESCRIPTION 
+      "The Destination Access Point Identifier (DAPI) 
+      expected by the receiver." 
+    SYNTAX OCTET STRING (SIZE(16)) 
+
+
+JnxoptIfExSAPI ::= TEXTUAL-CONVENTION 
+    STATUS current 
+    DESCRIPTION 
+      "The Source Access Point Identifier (SAPI) 
+      expected by the receiver." 
+    SYNTAX OCTET STRING (SIZE(16)) 
+
+
+JnxoptIfIntervalNumber ::= TEXTUAL-CONVENTION 
+    STATUS current 
+    DESCRIPTION 
+      "Uniquely identifies a 15-minute interval. The interval 
+      identified by 1 is the most recently completed interval, and 
+      the interval identified by n is the interval immediately 
+      preceding the one identified by n-1." 
+    SYNTAX Unsigned32 (1..96) 
+
+
+JnxoptIfTIMDetMode ::= TEXTUAL-CONVENTION 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the mode of the Trace Identifier Mismatch (TIM) 
+      Detection function."
+    SYNTAX INTEGER { 
+        off(1), 
+        dapi(2), 
+        sapi(3), 
+        both(4) 
+    } 
+
+
+JnxoptIfTxTI ::= TEXTUAL-CONVENTION 
+    STATUS current 
+    DESCRIPTION
+      "The trace identifier (TI) transmitted." 
+    SYNTAX OCTET STRING (SIZE(64)) 
+
+
+-- object groups 
+
+
+jnxoptIfObjects OBJECT IDENTIFIER ::= { jnxoptIfMibModule 1 } 
+jnxoptIfConfs OBJECT IDENTIFIER ::= { jnxoptIfMibModule 2 } 
+
+
+jnxoptIfOTMn OBJECT IDENTIFIER ::= { jnxoptIfObjects 1 } 
+jnxoptIfPerfMon OBJECT IDENTIFIER ::= { jnxoptIfObjects 2 } 
+jnxoptIfOTSn OBJECT IDENTIFIER ::= { jnxoptIfObjects 3 } 
+jnxoptIfOMSn OBJECT IDENTIFIER ::= { jnxoptIfObjects 4 } 
+jnxoptIfOChGroup OBJECT IDENTIFIER ::= { jnxoptIfObjects 5 } 
+jnxoptIfOCh OBJECT IDENTIFIER ::= { jnxoptIfObjects 6 } 
+
+
+jnxoptIfOTUk OBJECT IDENTIFIER ::= { jnxoptIfObjects 7 } 
+jnxoptIfODUk OBJECT IDENTIFIER ::= { jnxoptIfObjects 8 } 
+jnxoptIfODUkT OBJECT IDENTIFIER ::= { jnxoptIfObjects 9 } 
+
+
+jnxoptIfGroups OBJECT IDENTIFIER ::= { jnxoptIfConfs 1 } 
+jnxoptIfCompl OBJECT IDENTIFIER ::= { jnxoptIfConfs 2 } 
+
+
+-- the jnxoptIfOTMn group 
+-- This group defines the OTM structure information of an 
+-- optical interface. 
+
+
+-- OTMn Table 
+
+
+jnxoptIfOTMnTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOTMnEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OTMn structure information." 
+    ::= { jnxoptIfOTMn 1 } 
+
+
+jnxoptIfOTMnEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOTMnEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A conceptual row that contains the OTMn structure 
+      information of an optical interface." 
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOTMnTable 1 } 
+
+
+JnxoptIfOTMnEntry ::= 
+    SEQUENCE { 
+        jnxoptIfOTMnOrder Unsigned32, 
+        jnxoptIfOTMnReduced TruthValue, 
+        jnxoptIfOTMnBitRates BITS, 
+        jnxoptIfOTMnInterfaceType SnmpAdminString, 
+        jnxoptIfOTMnTcmMax Unsigned32, 
+        jnxoptIfOTMnOpticalReach INTEGER 
+    } 
+
+
+jnxoptIfOTMnOrder OBJECT-TYPE 
+    SYNTAX Unsigned32 (1..900) 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "This object indicates the order of the OTM, which 
+      represents the maximum number of wavelengths that can be 
+      supported at the bit rate(s) supported on the interface." 
+    ::= { jnxoptIfOTMnEntry 1 } 
+
+
+jnxoptIfOTMnReduced OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "This object indicates whether a reduced or full 
+      functionality is supported at the interface. A value of 
+      true means reduced. A value of false means full." 
+    ::= { jnxoptIfOTMnEntry 2 } 
+
+
+jnxoptIfOTMnBitRates OBJECT-TYPE 
+    SYNTAX BITS { bitRateK1(0), bitRateK2(1), bitRateK3(2) } 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "This attribute is a bit map representing the bit 
+      rate or set of bit rates supported on the interface. 
+      The meaning of each bit position is as follows:
+      bitRateK1(0) is set if the 2.5 Gbit/s rate is supported 
+      bitRateK2(1) is set if the 10 Gbit/s rate is supported 
+      bitRateK3(2) is set if the 40 Gbit/s rate is supported
+      Note that each bit position corresponds to one possible 
+      value of the type JnxoptIfBitRateK. 
+      The default value of this attribute is system specific."
+    ::= { jnxoptIfOTMnEntry 3 } 
+
+
+jnxoptIfOTMnInterfaceType OBJECT-TYPE 
+    SYNTAX SnmpAdminString 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "This object identifies the type of interface. The value of 
+      this attribute will affect the behavior of the OTM with 
+      respect to presence/absence of OTM Overhead Signal (OOS) 
+      processing and TCM activation. For an IrDI interface, 
+      there is no OOS processing and TCM activation is limited 
+      to n levels as specified by a TCM level threshold.
+      This object contains two fields that are separated by 
+      whitespace. The possible values are: 
+      field 1: one of the 4-character ASCII strings 
+      'IrDI' or 'IaDI'
+      field 2: free-form text consisting of printable 
+      UTF-8 encoded characters
+      Note that field 2 is optional. If it is not present then there 
+      is no requirement for trailing whitespace after field 1.
+      The default values are as follows: 
+      field 1: 'IaDI' field 2: an empty string."
+    ::= { jnxoptIfOTMnEntry 4 } 
+
+
+jnxoptIfOTMnTcmMax OBJECT-TYPE 
+    SYNTAX Unsigned32 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION 
+      "This object identifies the maximum number of TCM 
+      levels allowed for any Optical Channel contained 
+      in this OTM. A new TCM activation will be rejected 
+      if the requested level is greater than the threshold. 
+      If InterfaceType object specifies a type of 'IaDI' 
+      for this OTM, then this attribute is irrelevant.
+      Possible values: unsigned integers in the range 
+      from 0 to 6 inclusive. 
+      Default value: 3."
+    ::= { jnxoptIfOTMnEntry 5 } 
+
+
+jnxoptIfOTMnOpticalReach OBJECT-TYPE 
+    SYNTAX INTEGER { intraOffice(1), shortHaul(2), longHaul(3),
+                     veryLongHaul(4), ultraLongHaul(5) } 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "This object indicates the length the optical signal 
+      may travel before requiring termination or regeneration. 
+      The meaning of the enumeration are:
+      intraOffice(1) - intra-office (as defined in ITU-T G.957) 
+      shortHaul(2) - short haul (as defined in ITU-T G.957) 
+      longHaul(3) - long haul (as defined in ITU-T G.957) 
+      veryLongHaul(4) - very long haul (as defined in ITU-T G.691) 
+      ultraLongHaul(5)- ultra long haul (as defined in ITU-T G.691)"
+    ::= { jnxoptIfOTMnEntry 6 } 
+
+
+-- the jnxoptIfPerfMon group 
+-- This group defines performance monitoring objects for all 
+-- layers. 
+
+-- PM interval table 
+
+jnxoptIfPerfMonIntervalTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfPerfMonIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of 15-minute performance monitoring interval 
+      information." 
+    ::= { jnxoptIfPerfMon 1 } 
+
+
+jnxoptIfPerfMonIntervalEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfPerfMonIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A conceptual row that contains 15-minute performance
+       monitoring interval information of an interface." 
+    INDEX { ifIndex } 
+    ::= { jnxoptIfPerfMonIntervalTable 1 } 
+
+
+JnxoptIfPerfMonIntervalEntry ::=
+    SEQUENCE { 
+        jnxoptIfPerfMonCurrentTimeElapsed Gauge32, 
+        jnxoptIfPerfMonCurDayTimeElapsed Gauge32,
+        jnxoptIfPerfMonIntervalNumIntervals Unsigned32, 
+        jnxoptIfPerfMonIntervalNumInvalidIntervals Unsigned32 
+    } 
+
+jnxoptIfPerfMonCurrentTimeElapsed OBJECT-TYPE 
+    SYNTAX Gauge32 (0..900) 
+    UNITS "seconds" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "Number of seconds elapsed in the current 15-minute 
+      performance monitoring interval. 
+      If, for some reason, such as an adjustment in the NE's 
+      time-of-day clock, the number of seconds elapsed exceeds 
+      the maximum value, then the maximum value will be returned."
+    ::= { jnxoptIfPerfMonIntervalEntry 1 } 
+
+
+jnxoptIfPerfMonCurDayTimeElapsed OBJECT-TYPE 
+    SYNTAX Gauge32 (0..86400) 
+    UNITS "seconds" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "Number of seconds elapsed in the current 24-hour interval 
+      performance monitoring period. 
+      If, for some reason, such as an adjustment in the NE 
+      time-of-day clock, the number of seconds elapsed exceeds 
+      the maximum value, then the maximum value will be returned."
+    ::= { jnxoptIfPerfMonIntervalEntry 2 } 
+
+
+jnxoptIfPerfMonIntervalNumIntervals OBJECT-TYPE 
+    SYNTAX Unsigned32 (0..96) 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The number of 15-minute intervals for which performance 
+      monitoring data is available. The number is the same for all 
+      the associated sub layers of the interface. 
+      An optical interface must be capable of supporting at least
+      n intervals, where n is defined as follows: 
+      The minimum value of n is 4. 
+      The default of n is 32. 
+      The maximum value of n is 96.
+       The value of this object will be n unless performance 
+      monitoring was (re-)started for the interface within the last 
+      (n*15) minutes, in which case the value will be the number of 
+      complete 15-minute intervals since measurement was 
+      (re-)started."
+    ::= { jnxoptIfPerfMonIntervalEntry 3 } 
+
+
+jnxoptIfPerfMonIntervalNumInvalidIntervals OBJECT-TYPE 
+    SYNTAX Unsigned32 (0..96) 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The number of intervals in the range from 0 to 
+      jnxoptIfPerfMonIntervalNumIntervals for which no performance 
+      monitoring data is available and/or the data is invalid."
+    ::= { jnxoptIfPerfMonIntervalEntry 4 } 
+
+
+-- the jnxoptIfOTSn group 
+-- This group handles the configuration and performance 
+-- monitoring objects for OTS layers. 
+
+
+-- OTSn config table 
+
+jnxoptIfOTSnConfigTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOTSnConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OTSn configuration information." 
+    ::= { jnxoptIfOTSn 1 } 
+
+
+jnxoptIfOTSnConfigEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOTSnConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OTSn configuration
+      information of an interface." 
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOTSnConfigTable 1 } 
+
+
+JnxoptIfOTSnConfigEntry ::= 
+    SEQUENCE { 
+        jnxoptIfOTSnDirectionality               JnxoptIfDirectionality, 
+        jnxoptIfOTSnAprStatus                    SnmpAdminString, 
+        jnxoptIfOTSnAprControl                   SnmpAdminString, 
+        jnxoptIfOTSnTraceIdentifierTransmitted   JnxoptIfTxTI, 
+        jnxoptIfOTSnDAPIExpected                 JnxoptIfExDAPI, 
+        jnxoptIfOTSnSAPIExpected                 JnxoptIfExSAPI, 
+        jnxoptIfOTSnTraceIdentifierAccepted      JnxoptIfAcTI, 
+        jnxoptIfOTSnTIMDetMode                   JnxoptIfTIMDetMode, 
+        jnxoptIfOTSnTIMActEnabled                TruthValue, 
+        jnxoptIfOTSnCurrentStatus                BITS 
+    } 
+
+
+jnxoptIfOTSnDirectionality OBJECT-TYPE 
+    SYNTAX JnxoptIfDirectionality 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+     "Indicates the directionality of the entity." 
+    ::= { jnxoptIfOTSnConfigEntry 1 } 
+
+
+jnxoptIfOTSnAprStatus OBJECT-TYPE 
+    SYNTAX SnmpAdminString 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "This attribute indicates the status of the Automatic 
+      Power Reduction (APR) function of the entity. Valid 
+      values are 'on' and 'off'." 
+    ::= { jnxoptIfOTSnConfigEntry 2 } 
+
+
+jnxoptIfOTSnAprControl OBJECT-TYPE 
+    SYNTAX SnmpAdminString 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION 
+      "This object is a UTF-8 encoded string that specifies Automatic 
+      Power Reduction (APR) control actions requested of this entity 
+      (when written) and that returns the current APR control state 
+      of this entity (when read). The values are implementation-defined. 
+      Any implementation that instantiates this object must document the 
+      set of values that it allows to be written, the set of values 
+      that it will return, and what each of those values means." 
+    ::= { jnxoptIfOTSnConfigEntry 3 } 
+
+
+jnxoptIfOTSnTraceIdentifierTransmitted OBJECT-TYPE 
+    SYNTAX JnxoptIfTxTI 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The trace identifier transmitted. 
+      This object is applicable when jnxoptIfOTSnDirectionality has the 
+      value source(2) or bidirectional(3). 
+      This object does not apply to reduced-capability systems (i.e., 
+      those for which jnxoptIfOTMnReduced has the value true(1)) or 
+      at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 
+      has the value 'IrDI'). 
+      If no value is ever set by a management entity for the object 
+      jnxoptIfOTSnTraceIdentifierTransmitted, system-specific default 
+      value will be used. Any implementation that instantiates this 
+      object must document the system-specific default value or how it 
+      is derived."
+    ::= { jnxoptIfOTSnConfigEntry 4 } 
+
+
+jnxoptIfOTSnDAPIExpected OBJECT-TYPE 
+    SYNTAX JnxoptIfExDAPI 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The DAPI expected by the receiver. 
+      This object is applicable when jnxoptIfOTSnDirectionality has the 
+      value sink(1) or bidirectional(3). It has no effect if 
+      jnxoptIfOTSnTIMDetMode has the value off(1) or sapi(3). 
+      This object does not apply to reduced-capability systems (i.e., 
+      those for which jnxoptIfOTMnReduced has the value true(1)) or 
+      at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 
+      has the value 'IrDI')."
+    ::= { jnxoptIfOTSnConfigEntry 5 } 
+
+
+jnxoptIfOTSnSAPIExpected OBJECT-TYPE 
+    SYNTAX JnxoptIfExSAPI 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+     "The SAPI expected by the receiver. 
+      This object is applicable when jnxoptIfOTSnDirectionality has the 
+      value sink(1) or bidirectional(3). It has no effect if 
+      jnxoptIfOTSnTIMDetMode has the value off(1) or dapi(2). 
+      This object does not apply to reduced-capability systems (i.e., 
+      those for which jnxoptIfOTMnReduced has the value true(1)) or 
+      at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 
+      has the value 'IrDI')."
+    ::= { jnxoptIfOTSnConfigEntry 6 } 
+
+
+jnxoptIfOTSnTraceIdentifierAccepted OBJECT-TYPE 
+    SYNTAX JnxoptIfAcTI 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The actual trace identifier received. 
+      This object is applicable when jnxoptIfOTSnDirectionality has the 
+      value sink(1) or bidirectional(3). Its value is unspecified 
+      if jnxoptIfOTSnCurrentStatus has either or both of the 
+      losO(5) and los(6) bits set. 
+      This object does not apply to reduced-capability systems (i.e., 
+      those for which jnxoptIfOTMnReduced has the value true(1)) or 
+      at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 
+      has the value 'IrDI')."
+    ::= { jnxoptIfOTSnConfigEntry 7 } 
+
+
+jnxoptIfOTSnTIMDetMode OBJECT-TYPE 
+    SYNTAX JnxoptIfTIMDetMode 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the mode of the Trace Identifier Mismatch (TIM) 
+      Detection function. This object is applicable 
+      when jnxoptIfOTSnDirectionality has the value sink(1) 
+      or bidirectional(3). The default value is off(1). 
+      This object does not apply to reduced-capability systems (i.e., 
+      those for which jnxoptIfOTMnReduced has the value true(1)) or 
+      at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 
+      has the value 'IrDI'). 
+      The default value of this object is off(1)."
+    ::= { jnxoptIfOTSnConfigEntry 8 } 
+
+
+jnxoptIfOTSnTIMActEnabled OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+     "Indicates whether the Trace Identifier Mismatch (TIM) 
+      Consequent Action function is enabled. This object 
+      is applicable when jnxoptIfOTSnDirectionality has the 
+      value sink(1) or bidirectional(3). It has no effect 
+      when the value of jnxoptIfOTSnTIMDetMode is off(1). 
+      This object does not apply to reduced-capability systems (i.e., 
+      those for which jnxoptIfOTMnReduced has the value true(1)) or 
+      at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 
+      has the value 'IrDI'). 
+      The default value of this object is false(2)."
+    ::= { jnxoptIfOTSnConfigEntry 9 } 
+
+
+jnxoptIfOTSnCurrentStatus OBJECT-TYPE 
+     SYNTAX BITS { 
+        bdiP(0), 
+        bdiO(1), 
+        bdi(2), 
+        tim(3), 
+        losP(4), 
+        losO(5), 
+        los(6) 
+    }
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+     "Indicates the defect condition of the entity, if any. 
+      This object is applicable when jnxoptIfOTSnDirectionality 
+      has the value sink(1) or bidirectional(3). In 
+      reduced-capability systems or at IrDI interfaces 
+      the only bit position that may be set is los(6)."
+    ::= { jnxoptIfOTSnConfigEntry 10 } 
+
+
+-- OTSn sink current table 
+-- Contains data for the current 15-minute performance monitoring 
+-- interval. 
+
+jnxoptIfOTSnSinkCurrentTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOTSnSinkCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OTSn sink performance monitoring information for 
+      the current 15-minute interval." 
+    ::= { jnxoptIfOTSn 2 } 
+
+
+jnxoptIfOTSnSinkCurrentEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOTSnSinkCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OTSn sink performance 
+      monitoring information of an interface for the current 
+      15-minute interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOTSnSinkCurrentTable 1 } 
+
+
+JnxoptIfOTSnSinkCurrentEntry ::=
+    SEQUENCE { 
+        jnxoptIfOTSnSinkCurrentSuspectedFlag             TruthValue, 
+        jnxoptIfOTSnSinkCurrentInputPower                Integer32, 
+        jnxoptIfOTSnSinkCurrentLowInputPower             Integer32, 
+        jnxoptIfOTSnSinkCurrentHighInputPower            Integer32, 
+        jnxoptIfOTSnSinkCurrentLowerInputPowerThreshold  Integer32, 
+        jnxoptIfOTSnSinkCurrentUpperInputPowerThreshold  Integer32, 
+        jnxoptIfOTSnSinkCurrentOutputPower               Integer32, 
+        jnxoptIfOTSnSinkCurrentLowOutputPower            Integer32, 
+        jnxoptIfOTSnSinkCurrentHighOutputPower           Integer32,
+        jnxoptIfOTSnSinkCurrentLowerOutputPowerThreshold Integer32, 
+        jnxoptIfOTSnSinkCurrentUpperOutputPowerThreshold Integer32 
+    } 
+
+
+jnxoptIfOTSnSinkCurrentSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOTSnSinkCurrentEntry 1 } 
+
+
+jnxoptIfOTSnSinkCurrentInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The optical power monitored at the input." 
+    ::= { jnxoptIfOTSnSinkCurrentEntry 2 } 
+
+
+jnxoptIfOTSnSinkCurrentLowInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the input during the 
+      current 15-minute interval." 
+    ::= { jnxoptIfOTSnSinkCurrentEntry 3 } 
+
+
+jnxoptIfOTSnSinkCurrentHighInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the input during the 
+      current 15-minute interval." 
+    ::= { jnxoptIfOTSnSinkCurrentEntry 4 } 
+
+
+jnxoptIfOTSnSinkCurrentLowerInputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The lower limit threshold on input power. If 
+      jnxoptIfOTSnSinkCurrentInputPower drops to this value or below, 
+      a Threshold Crossing Alert (TCA) should be sent."
+     ::= { jnxoptIfOTSnSinkCurrentEntry 5 } 
+
+
+jnxoptIfOTSnSinkCurrentUpperInputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The upper limit threshold on input power. If 
+      jnxoptIfOTSnSinkCurrentInputPower reaches or exceeds this value, 
+      a Threshold Crossing Alert (TCA) should be sent."
+     ::= { jnxoptIfOTSnSinkCurrentEntry 6 } 
+
+
+jnxoptIfOTSnSinkCurrentOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The optical power monitored at the output." 
+    ::= { jnxoptIfOTSnSinkCurrentEntry 7 } 
+
+
+jnxoptIfOTSnSinkCurrentLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      current 15-minute interval." 
+    ::= { jnxoptIfOTSnSinkCurrentEntry 8 } 
+
+
+jnxoptIfOTSnSinkCurrentHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      current 15-minute interval." 
+    ::= { jnxoptIfOTSnSinkCurrentEntry 9 } 
+
+
+jnxoptIfOTSnSinkCurrentLowerOutputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The lower limit threshold on output power. If 
+      jnxoptIfOTSnSinkCurrentOutputPower drops to this value or below, 
+      a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOTSnSinkCurrentEntry 10 } 
+
+
+jnxoptIfOTSnSinkCurrentUpperOutputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The upper limit threshold on output power. If 
+      jnxoptIfOTSnSinkCurrentOutputPower reaches or exceeds this value, 
+      a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOTSnSinkCurrentEntry 11 } 
+
+
+-- OTSn sink interval table 
+-- Contains data for previous 15-minute performance monitoring 
+-- intervals. 
+
+
+jnxoptIfOTSnSinkIntervalTable OBJECT-TYPE 
+   SYNTAX SEQUENCE OF JnxoptIfOTSnSinkIntervalEntry 
+   MAX-ACCESS not-accessible 
+   STATUS current 
+   DESCRIPTION
+     "A table of historical OTSn sink performance monitoring 
+     information." 
+   ::= { jnxoptIfOTSn 3 } 
+
+
+jnxoptIfOTSnSinkIntervalEntry OBJECT-TYPE 
+   SYNTAX JnxoptIfOTSnSinkIntervalEntry 
+   MAX-ACCESS not-accessible 
+   STATUS current 
+   DESCRIPTION
+     "A conceptual row that contains OTSn sink performance 
+      monitoring information of an interface during a particular 
+      historical interval."
+   INDEX { ifIndex, jnxoptIfOTSnSinkIntervalNumber } 
+   ::= { jnxoptIfOTSnSinkIntervalTable 1 } 
+
+JnxoptIfOTSnSinkIntervalEntry ::=
+
+    SEQUENCE { 
+        jnxoptIfOTSnSinkIntervalNumber          JnxoptIfIntervalNumber, 
+        jnxoptIfOTSnSinkIntervalSuspectedFlag   TruthValue, 
+        jnxoptIfOTSnSinkIntervalLastInputPower  Integer32, 
+        jnxoptIfOTSnSinkIntervalLowInputPower   Integer32, 
+        jnxoptIfOTSnSinkIntervalHighInputPower  Integer32, 
+        jnxoptIfOTSnSinkIntervalLastOutputPower Integer32, 
+        jnxoptIfOTSnSinkIntervalLowOutputPower  Integer32, 
+        jnxoptIfOTSnSinkIntervalHighOutputPower Integer32
+    } 
+
+
+jnxoptIfOTSnSinkIntervalNumber OBJECT-TYPE 
+    SYNTAX JnxoptIfIntervalNumber 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "Uniquely identifies the interval." 
+    ::= { jnxoptIfOTSnSinkIntervalEntry 1 } 
+
+
+jnxoptIfOTSnSinkIntervalSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOTSnSinkIntervalEntry 2 } 
+
+
+jnxoptIfOTSnSinkIntervalLastInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the input during the 
+      interval." 
+    ::= { jnxoptIfOTSnSinkIntervalEntry 3 } 
+
+
+jnxoptIfOTSnSinkIntervalLowInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the input during the 
+      interval." 
+    ::= { jnxoptIfOTSnSinkIntervalEntry 4 } 
+
+
+
+jnxoptIfOTSnSinkIntervalHighInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the input during the 
+      interval." 
+    ::= { jnxoptIfOTSnSinkIntervalEntry 5 } 
+
+
+jnxoptIfOTSnSinkIntervalLastOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOTSnSinkIntervalEntry 6 } 
+
+
+jnxoptIfOTSnSinkIntervalLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOTSnSinkIntervalEntry 7 } 
+
+ 
+jnxoptIfOTSnSinkIntervalHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOTSnSinkIntervalEntry 8 } 
+
+
+-- OTSn sink current day table 
+-- Contains data for the current 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOTSnSinkCurDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOTSnSinkCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A table of OTSn sink performance monitoring information for 
+      the current 24-hour interval." 
+    ::= { jnxoptIfOTSn 4 } 
+
+
+jnxoptIfOTSnSinkCurDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOTSnSinkCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OTSn sink performance 
+      monitoring information of an interface for the current 
+      24-hour interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOTSnSinkCurDayTable 1 } 
+ 
+
+JnxoptIfOTSnSinkCurDayEntry ::=
+    SEQUENCE { 
+        jnxoptIfOTSnSinkCurDaySuspectedFlag TruthValue, 
+        jnxoptIfOTSnSinkCurDayLowInputPower Integer32, 
+        jnxoptIfOTSnSinkCurDayHighInputPower Integer32, 
+        jnxoptIfOTSnSinkCurDayLowOutputPower Integer32, 
+        jnxoptIfOTSnSinkCurDayHighOutputPower Integer32 
+    } 
+
+
+jnxoptIfOTSnSinkCurDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOTSnSinkCurDayEntry 1 } 
+
+
+jnxoptIfOTSnSinkCurDayLowInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the input during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOTSnSinkCurDayEntry 2 } 
+
+
+jnxoptIfOTSnSinkCurDayHighInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "The highest optical power monitored at the input during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOTSnSinkCurDayEntry 3 } 
+ 
+
+jnxoptIfOTSnSinkCurDayLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOTSnSinkCurDayEntry 4 } 
+
+
+jnxoptIfOTSnSinkCurDayHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOTSnSinkCurDayEntry 5 } 
+ 
+
+-- OTSn sink previous day table 
+-- Contains data for the previous 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOTSnSinkPrevDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOTSnSinkPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OTSn sink performance monitoring information for 
+      the previous 24-hour interval." 
+    ::= { jnxoptIfOTSn 5 } 
+
+
+jnxoptIfOTSnSinkPrevDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOTSnSinkPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OTSn sink performance 
+      monitoring information of an interface for the previous 
+      24-hour interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOTSnSinkPrevDayTable 1 } 
+
+
+
+
+JnxoptIfOTSnSinkPrevDayEntry ::=
+    SEQUENCE { 
+        jnxoptIfOTSnSinkPrevDaySuspectedFlag      TruthValue, 
+        jnxoptIfOTSnSinkPrevDayLastInputPower     Integer32, 
+        jnxoptIfOTSnSinkPrevDayLowInputPower      Integer32, 
+        jnxoptIfOTSnSinkPrevDayHighInputPower     Integer32, 
+        jnxoptIfOTSnSinkPrevDayLastOutputPower    Integer32, 
+        jnxoptIfOTSnSinkPrevDayLowOutputPower     Integer32, 
+        jnxoptIfOTSnSinkPrevDayHighOutputPower    Integer32 
+    } 
+
+
+jnxoptIfOTSnSinkPrevDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOTSnSinkPrevDayEntry 1 } 
+
+
+jnxoptIfOTSnSinkPrevDayLastInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the input during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOTSnSinkPrevDayEntry 2 } 
+
+
+jnxoptIfOTSnSinkPrevDayLowInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the input during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOTSnSinkPrevDayEntry 3 } 
+
+
+jnxoptIfOTSnSinkPrevDayHighInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the input during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOTSnSinkPrevDayEntry 4 } 
+
+
+
+jnxoptIfOTSnSinkPrevDayLastOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the output during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOTSnSinkPrevDayEntry 5 } 
+
+
+jnxoptIfOTSnSinkPrevDayLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOTSnSinkPrevDayEntry 6 } 
+
+
+jnxoptIfOTSnSinkPrevDayHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOTSnSinkPrevDayEntry 7 } 
+
+
+-- OTSn source current table 
+-- Contains data for the current 15-minute performance monitoring 
+-- interval. 
+
+
+jnxoptIfOTSnSrcCurrentTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOTSnSrcCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OTSn source performance monitoring information for 
+      the current 15-minute interval." 
+    ::= { jnxoptIfOTSn 6 } 
+ 
+
+jnxoptIfOTSnSrcCurrentEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOTSnSrcCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A conceptual row that contains OTSn source performance 
+      monitoring information of an interface for the current
+      15-minute interval." 
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOTSnSrcCurrentTable 1 } 
+
+
+JnxoptIfOTSnSrcCurrentEntry ::=
+    SEQUENCE { 
+        jnxoptIfOTSnSrcCurrentSuspectedFlag             TruthValue,
+        jnxoptIfOTSnSrcCurrentOutputPower               Integer32, 
+        jnxoptIfOTSnSrcCurrentLowOutputPower            Integer32, 
+        jnxoptIfOTSnSrcCurrentHighOutputPower           Integer32,
+        jnxoptIfOTSnSrcCurrentLowerOutputPowerThreshold Integer32, 
+        jnxoptIfOTSnSrcCurrentUpperOutputPowerThreshold Integer32, 
+        jnxoptIfOTSnSrcCurrentInputPower                Integer32, 
+        jnxoptIfOTSnSrcCurrentLowInputPower             Integer32,
+        jnxoptIfOTSnSrcCurrentHighInputPower            Integer32, 
+        jnxoptIfOTSnSrcCurrentLowerInputPowerThreshold  Integer32, 
+        jnxoptIfOTSnSrcCurrentUpperInputPowerThreshold  Integer32
+    } 
+
+
+jnxoptIfOTSnSrcCurrentSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOTSnSrcCurrentEntry 1 } 
+
+
+jnxoptIfOTSnSrcCurrentOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The optical power monitored at the output." 
+    ::= { jnxoptIfOTSnSrcCurrentEntry 2 } 
+
+
+jnxoptIfOTSnSrcCurrentLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current
+    DESCRIPTION 
+      "The lowest optical power monitored at the output during the 
+      current 15-minute interval." 
+    ::= { jnxoptIfOTSnSrcCurrentEntry 3 } 
+
+
+
+jnxoptIfOTSnSrcCurrentHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      current 15-minute interval." 
+    ::= { jnxoptIfOTSnSrcCurrentEntry 4 } 
+
+
+jnxoptIfOTSnSrcCurrentLowerOutputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The lower limit threshold on output power. If 
+      jnxoptIfOTSnSrcCurrentOutputPower drops to this value or below, 
+      a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOTSnSrcCurrentEntry 5 } 
+
+
+jnxoptIfOTSnSrcCurrentUpperOutputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The upper limit threshold on output power. If 
+      jnxoptIfOTSnSrcCurrentOutputPower reaches or exceeds this value, 
+      a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOTSnSrcCurrentEntry 6 } 
+
+
+jnxoptIfOTSnSrcCurrentInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The optical power monitored at the input." 
+    ::= { jnxoptIfOTSnSrcCurrentEntry 7 } 
+
+
+jnxoptIfOTSnSrcCurrentLowInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current
+    DESCRIPTION 
+      "The lowest optical power monitored at the input during the 
+      current 15-minute interval." 
+    ::= { jnxoptIfOTSnSrcCurrentEntry 8 } 
+ 
+
+jnxoptIfOTSnSrcCurrentHighInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the input during the 
+      current 15-minute interval." 
+    ::= { jnxoptIfOTSnSrcCurrentEntry 9 } 
+
+
+jnxoptIfOTSnSrcCurrentLowerInputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The lower limit threshold on input power. If 
+      jnxoptIfOTSnSrcCurrentInputPower drops to this value or below, 
+      a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOTSnSrcCurrentEntry 10 } 
+
+
+jnxoptIfOTSnSrcCurrentUpperInputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The upper limit threshold on input power. If 
+      jnxoptIfOTSnSrcCurrentInputPower reaches or exceeds this value, 
+      a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOTSnSrcCurrentEntry 11 } 
+
+
+-- OTSn source interval table 
+-- Contains data for previous 15-minute performance monitoring 
+-- intervals. 
+
+
+jnxoptIfOTSnSrcIntervalTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOTSnSrcIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of historical OTSn source performance monitoring 
+      information." 
+    ::= { jnxoptIfOTSn 7 } 
+
+
+jnxoptIfOTSnSrcIntervalEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOTSnSrcIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OTSn source performance 
+      monitoring information of an interface during a particular 
+      historical interval."
+    INDEX { ifIndex, jnxoptIfOTSnSrcIntervalNumber } 
+    ::= { jnxoptIfOTSnSrcIntervalTable 1 } 
+ 
+
+JnxoptIfOTSnSrcIntervalEntry ::=
+    SEQUENCE { 
+        jnxoptIfOTSnSrcIntervalNumber          JnxoptIfIntervalNumber, 
+        jnxoptIfOTSnSrcIntervalSuspectedFlag   TruthValue, 
+        jnxoptIfOTSnSrcIntervalLastOutputPower Integer32, 
+        jnxoptIfOTSnSrcIntervalLowOutputPower  Integer32, 
+        jnxoptIfOTSnSrcIntervalHighOutputPower Integer32, 
+        jnxoptIfOTSnSrcIntervalLastInputPower  Integer32, 
+        jnxoptIfOTSnSrcIntervalLowInputPower   Integer32, 
+        jnxoptIfOTSnSrcIntervalHighInputPower  Integer32 
+    } 
+
+
+jnxoptIfOTSnSrcIntervalNumber OBJECT-TYPE 
+    SYNTAX JnxoptIfIntervalNumber 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "Uniquely identifies the interval." 
+    ::= { jnxoptIfOTSnSrcIntervalEntry 1 } 
+
+
+jnxoptIfOTSnSrcIntervalSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOTSnSrcIntervalEntry 2 } 
+
+
+jnxoptIfOTSnSrcIntervalLastOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOTSnSrcIntervalEntry 3 } 
+
+
+
+jnxoptIfOTSnSrcIntervalLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOTSnSrcIntervalEntry 4 } 
+
+
+jnxoptIfOTSnSrcIntervalHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOTSnSrcIntervalEntry 5 } 
+
+
+jnxoptIfOTSnSrcIntervalLastInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the input during the 
+      interval." 
+    ::= { jnxoptIfOTSnSrcIntervalEntry 6 } 
+ 
+
+jnxoptIfOTSnSrcIntervalLowInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the input during the 
+      interval." 
+    ::= { jnxoptIfOTSnSrcIntervalEntry 7 } 
+
+
+jnxoptIfOTSnSrcIntervalHighInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the input during the 
+      interval." 
+    ::= { jnxoptIfOTSnSrcIntervalEntry 8 } 
+
+
+-- OTSn source current day table 
+-- Contains data for the current 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOTSnSrcCurDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOTSnSrcCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OTSn source performance monitoring information for 
+      the current 24-hour interval." 
+    ::= { jnxoptIfOTSn 8 } 
+
+
+jnxoptIfOTSnSrcCurDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOTSnSrcCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OTSn source performance 
+      monitoring information of an interface for the current 
+      24-hour interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOTSnSrcCurDayTable 1 } 
+
+
+JnxoptIfOTSnSrcCurDayEntry ::=
+    SEQUENCE { 
+        jnxoptIfOTSnSrcCurDaySuspectedFlag   TruthValue, 
+        jnxoptIfOTSnSrcCurDayLowOutputPower  Integer32, 
+        jnxoptIfOTSnSrcCurDayHighOutputPower Integer32, 
+        jnxoptIfOTSnSrcCurDayLowInputPower   Integer32, 
+        jnxoptIfOTSnSrcCurDayHighInputPower  Integer32 
+    } 
+
+
+jnxoptIfOTSnSrcCurDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOTSnSrcCurDayEntry 1 } 
+
+
+jnxoptIfOTSnSrcCurDayLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "The lowest optical power monitored at the output during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOTSnSrcCurDayEntry 2 } 
+
+
+jnxoptIfOTSnSrcCurDayHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOTSnSrcCurDayEntry 3 } 
+
+
+jnxoptIfOTSnSrcCurDayLowInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the input during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOTSnSrcCurDayEntry 4 } 
+
+
+jnxoptIfOTSnSrcCurDayHighInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the input during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOTSnSrcCurDayEntry 5 } 
+
+
+-- OTSn source previous day table 
+-- Contains data for the previous 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOTSnSrcPrevDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOTSnSrcPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OTSn source performance monitoring information for 
+      the previous 24-hour interval." 
+    ::= { jnxoptIfOTSn 9 } 
+
+
+
+jnxoptIfOTSnSrcPrevDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOTSnSrcPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OTSn source performance 
+      monitoring information of an interface for the previous 
+      24-hour interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOTSnSrcPrevDayTable 1 } 
+
+
+JnxoptIfOTSnSrcPrevDayEntry ::=
+    SEQUENCE { 
+        jnxoptIfOTSnSrcPrevDaySuspectedFlag   TruthValue, 
+        jnxoptIfOTSnSrcPrevDayLastOutputPower Integer32, 
+        jnxoptIfOTSnSrcPrevDayLowOutputPower  Integer32, 
+        jnxoptIfOTSnSrcPrevDayHighOutputPower Integer32, 
+        jnxoptIfOTSnSrcPrevDayLastInputPower  Integer32, 
+        jnxoptIfOTSnSrcPrevDayLowInputPower   Integer32, 
+        jnxoptIfOTSnSrcPrevDayHighInputPower  Integer32 
+    } 
+
+
+jnxoptIfOTSnSrcPrevDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOTSnSrcPrevDayEntry 1 } 
+
+
+jnxoptIfOTSnSrcPrevDayLastOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the output during the 
+       previous 24-hour interval." 
+    ::= { jnxoptIfOTSnSrcPrevDayEntry 2 } 
+
+
+jnxoptIfOTSnSrcPrevDayLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOTSnSrcPrevDayEntry 3 } 
+
+
+jnxoptIfOTSnSrcPrevDayHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOTSnSrcPrevDayEntry 4 } 
+
+
+jnxoptIfOTSnSrcPrevDayLastInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the input during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOTSnSrcPrevDayEntry 5 } 
+   
+
+jnxoptIfOTSnSrcPrevDayLowInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the input during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOTSnSrcPrevDayEntry 6 } 
+
+
+jnxoptIfOTSnSrcPrevDayHighInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the input during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOTSnSrcPrevDayEntry 7 } 
+
+
+-- the jnxoptIfOMSn group 
+-- This group handles the configuration and performance monitoring 
+-- information for OMS layers. 
+
+
+-- OMSn config table 
+
+
+
+jnxoptIfOMSnConfigTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOMSnConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OMSn configuration information." 
+    ::= { jnxoptIfOMSn 1 } 
+
+
+jnxoptIfOMSnConfigEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOMSnConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OMSn configuration
+      information of an interface." 
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOMSnConfigTable 1 } 
+
+
+JnxoptIfOMSnConfigEntry ::=
+    SEQUENCE { 
+        jnxoptIfOMSnDirectionality JnxoptIfDirectionality, 
+        jnxoptIfOMSnCurrentStatus  BITS 
+    } 
+
+
+jnxoptIfOMSnDirectionality OBJECT-TYPE 
+    SYNTAX JnxoptIfDirectionality 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the directionality of the entity." 
+    ::= { jnxoptIfOMSnConfigEntry 1 } 
+
+
+jnxoptIfOMSnCurrentStatus OBJECT-TYPE
+    SYNTAX BITS { 
+       ssfP(0), 
+       ssfO(1), 
+       ssf(2), 
+       bdiP(3), 
+       bdiO(4), 
+       bdi(5), 
+       losP(6) 
+    }
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the defect condition of the entity, if any. 
+      This object is applicable only to full capability 
+      systems whose interface type is IaDI and for which 
+      jnxoptIfOMSnDirectionality has the value sink(1) or 
+      bidirectional(3)." 
+    ::= { jnxoptIfOMSnConfigEntry 2 } 
+
+
+-- OMSn sink current table 
+-- Contains data for the current 15-minute performance monitoring 
+-- interval. 
+
+
+jnxoptIfOMSnSinkCurrentTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOMSnSinkCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OMSn sink performance monitoring information for 
+      the current 15-minute interval." 
+    ::= { jnxoptIfOMSn 2 } 
+
+
+jnxoptIfOMSnSinkCurrentEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOMSnSinkCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OMSn sink performance 
+      monitoring information of an interface for the current
+      15-minute interval." 
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOMSnSinkCurrentTable 1 } 
+
+
+JnxoptIfOMSnSinkCurrentEntry ::=
+    SEQUENCE { 
+        jnxoptIfOMSnSinkCurrentSuspectedFlag              TruthValue,
+        jnxoptIfOMSnSinkCurrentAggregatedInputPower       Integer32,
+        jnxoptIfOMSnSinkCurrentLowAggregatedInputPower    Integer32,
+        jnxoptIfOMSnSinkCurrentHighAggregatedInputPower   Integer32,
+        jnxoptIfOMSnSinkCurrentLowerInputPowerThreshold   Integer32,
+        jnxoptIfOMSnSinkCurrentUpperInputPowerThreshold   Integer32,
+        jnxoptIfOMSnSinkCurrentOutputPower                Integer32,
+        jnxoptIfOMSnSinkCurrentLowOutputPower             Integer32,
+        jnxoptIfOMSnSinkCurrentHighOutputPower            Integer32,
+        jnxoptIfOMSnSinkCurrentLowerOutputPowerThreshold  Integer32,
+        jnxoptIfOMSnSinkCurrentUpperOutputPowerThreshold  Integer32
+    } 
+
+
+jnxoptIfOMSnSinkCurrentSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOMSnSinkCurrentEntry 1 } 
+
+
+jnxoptIfOMSnSinkCurrentAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The aggregated optical power of all the DWDM input 
+      channels." 
+    ::= { jnxoptIfOMSnSinkCurrentEntry 2 } 
+
+
+jnxoptIfOMSnSinkCurrentLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power of all the DWDM input 
+      channels during the current 15-minute interval." 
+    ::= { jnxoptIfOMSnSinkCurrentEntry 3 } 
+
+
+jnxoptIfOMSnSinkCurrentHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power of all the DWDM input 
+      channels during the current 15-minute interval." 
+    ::= { jnxoptIfOMSnSinkCurrentEntry 4 } 
+
+
+jnxoptIfOMSnSinkCurrentLowerInputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The lower limit threshold on aggregated input power. If 
+      jnxoptIfOMSnSinkCurrentAggregatedInputPower drops to this value 
+      or below, a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOMSnSinkCurrentEntry 5 } 
+
+
+jnxoptIfOMSnSinkCurrentUpperInputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The upper limit threshold on aggregated input power. If 
+      jnxoptIfOMSnSinkCurrentAggregatedInputPower reaches or exceeds 
+      this value, a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOMSnSinkCurrentEntry 6 } 
+
+
+jnxoptIfOMSnSinkCurrentOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The optical power monitored at the output." 
+      ::= { jnxoptIfOMSnSinkCurrentEntry 7 } 
+  
+
+jnxoptIfOMSnSinkCurrentLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output 
+      during the current 15-minute interval." 
+    ::= { jnxoptIfOMSnSinkCurrentEntry 8 } 
+
+
+jnxoptIfOMSnSinkCurrentHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output 
+      during the current 15-minute interval." 
+    ::= { jnxoptIfOMSnSinkCurrentEntry 9 } 
+
+
+jnxoptIfOMSnSinkCurrentLowerOutputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The lower limit threshold on output power. If 
+      jnxoptIfOMSnSinkCurrentOutputPower drops to this value 
+      or below, a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOMSnSinkCurrentEntry 10 } 
+
+
+jnxoptIfOMSnSinkCurrentUpperOutputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The upper limit threshold on output power. If 
+      jnxoptIfOMSnSinkCurrentOutputPower reaches or exceeds 
+      this value, a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOMSnSinkCurrentEntry 11 } 
+
+
+-- OMSn sink interval table 
+-- Contains data for previous 15-minute performance monitoring 
+-- intervals. 
+
+
+jnxoptIfOMSnSinkIntervalTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOMSnSinkIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of historical OMSn sink performance monitoring 
+      information." 
+    ::= { jnxoptIfOMSn 3 } 
+
+
+jnxoptIfOMSnSinkIntervalEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOMSnSinkIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OMSn sink performance 
+      monitoring information of an interface during a particular 
+      historical interval."
+    INDEX { ifIndex, jnxoptIfOMSnSinkIntervalNumber } 
+    ::= { jnxoptIfOMSnSinkIntervalTable 1 } 
+  
+
+JnxoptIfOMSnSinkIntervalEntry ::=
+    SEQUENCE { 
+        jnxoptIfOMSnSinkIntervalNumber                   JnxoptIfIntervalNumber,
+        jnxoptIfOMSnSinkIntervalSuspectedFlag            TruthValue,
+        jnxoptIfOMSnSinkIntervalLastAggregatedInputPower Integer32,
+        jnxoptIfOMSnSinkIntervalLowAggregatedInputPower  Integer32,
+        jnxoptIfOMSnSinkIntervalHighAggregatedInputPower Integer32,
+        jnxoptIfOMSnSinkIntervalLastOutputPower          Integer32,
+        jnxoptIfOMSnSinkIntervalLowOutputPower           Integer32,
+        jnxoptIfOMSnSinkIntervalHighOutputPower          Integer32
+    } 
+
+
+jnxoptIfOMSnSinkIntervalNumber OBJECT-TYPE 
+    SYNTAX JnxoptIfIntervalNumber 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "Uniquely identifies the interval." 
+    ::= { jnxoptIfOMSnSinkIntervalEntry 1 } 
+
+
+jnxoptIfOMSnSinkIntervalSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOMSnSinkIntervalEntry 2 } 
+
+
+jnxoptIfOMSnSinkIntervalLastAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last aggregated optical power of all the DWDM input 
+      channels during the interval." 
+    ::= { jnxoptIfOMSnSinkIntervalEntry 3 } 
+
+
+jnxoptIfOMSnSinkIntervalLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power of all the DWDM input 
+      channels during the interval." 
+    ::= { jnxoptIfOMSnSinkIntervalEntry 4 } 
+
+
+jnxoptIfOMSnSinkIntervalHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power of all the DWDM input 
+      channels during the interval." 
+    ::= { jnxoptIfOMSnSinkIntervalEntry 5 } 
+
+
+jnxoptIfOMSnSinkIntervalLastOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "The last optical power at the output 
+      during the interval." 
+    ::= { jnxoptIfOMSnSinkIntervalEntry 6 } 
+
+
+jnxoptIfOMSnSinkIntervalLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power at the output 
+      during the interval." 
+    ::= { jnxoptIfOMSnSinkIntervalEntry 7 } 
+
+
+jnxoptIfOMSnSinkIntervalHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power at the output 
+      during the interval." 
+    ::= { jnxoptIfOMSnSinkIntervalEntry 8 } 
+
+
+-- OMSn sink current day table 
+-- Contains data for the current 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOMSnSinkCurDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOMSnSinkCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OMSn sink performance monitoring information for 
+      the current 24-hour interval." 
+    ::= { jnxoptIfOMSn 4 } 
+
+
+jnxoptIfOMSnSinkCurDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOMSnSinkCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OMSn sink performance 
+      monitoring information of an interface for the current 
+      24-hour interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOMSnSinkCurDayTable 1 } 
+ 
+
+JnxoptIfOMSnSinkCurDayEntry ::=
+    SEQUENCE { 
+        jnxoptIfOMSnSinkCurDaySuspectedFlag             TruthValue,
+        jnxoptIfOMSnSinkCurDayLowAggregatedInputPower   Integer32,
+        jnxoptIfOMSnSinkCurDayHighAggregatedInputPower  Integer32,
+        jnxoptIfOMSnSinkCurDayLowOutputPower            Integer32,
+        jnxoptIfOMSnSinkCurDayHighOutputPower           Integer32
+    } 
+
+
+jnxoptIfOMSnSinkCurDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+      ::= { jnxoptIfOMSnSinkCurDayEntry 1 } 
+  
+
+jnxoptIfOMSnSinkCurDayLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power of all the DWDM input 
+      channels during the current 24-hour interval." 
+    ::= { jnxoptIfOMSnSinkCurDayEntry 2 } 
+
+
+jnxoptIfOMSnSinkCurDayHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power of all the DWDM input 
+      channels during the current 24-hour interval." 
+    ::= { jnxoptIfOMSnSinkCurDayEntry 3 } 
+
+
+jnxoptIfOMSnSinkCurDayLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power at the output 
+      during the current 24-hour interval." 
+    ::= { jnxoptIfOMSnSinkCurDayEntry 4 } 
+
+
+
+jnxoptIfOMSnSinkCurDayHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power at the output 
+      during the current 24-hour interval." 
+    ::= { jnxoptIfOMSnSinkCurDayEntry 5 } 
+
+
+-- OMSn sink previous day table 
+-- Contains data for the previous 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOMSnSinkPrevDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOMSnSinkPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OMSn sink performance monitoring information for 
+      the previous 24-hour interval." 
+    ::= { jnxoptIfOMSn 5 } 
+
+
+jnxoptIfOMSnSinkPrevDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOMSnSinkPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OMSn sink performance 
+      monitoring information of an interface for the previous 
+      24-hour interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOMSnSinkPrevDayTable 1 } 
+
+
+JnxoptIfOMSnSinkPrevDayEntry ::=
+    SEQUENCE { 
+       jnxoptIfOMSnSinkPrevDaySuspectedFlag             TruthValue,
+       jnxoptIfOMSnSinkPrevDayLastAggregatedInputPower  Integer32,
+       jnxoptIfOMSnSinkPrevDayLowAggregatedInputPower   Integer32,
+       jnxoptIfOMSnSinkPrevDayHighAggregatedInputPower  Integer32,
+       jnxoptIfOMSnSinkPrevDayLastOutputPower           Integer32,
+       jnxoptIfOMSnSinkPrevDayLowOutputPower            Integer32,
+       jnxoptIfOMSnSinkPrevDayHighOutputPower           Integer32
+    } 
+ 
+
+jnxoptIfOMSnSinkPrevDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOMSnSinkPrevDayEntry 1 } 
+
+
+jnxoptIfOMSnSinkPrevDayLastAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last aggregated optical power of all the DWDM input 
+      channels during the previous 24-hour interval." 
+    ::= { jnxoptIfOMSnSinkPrevDayEntry 2 } 
+
+
+jnxoptIfOMSnSinkPrevDayLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power of all the DWDM input 
+      channels during the previous 24-hour interval." 
+    ::= { jnxoptIfOMSnSinkPrevDayEntry 3 } 
+
+
+jnxoptIfOMSnSinkPrevDayHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power of all the DWDM input 
+      channels during the previous 24-hour interval." 
+    ::= { jnxoptIfOMSnSinkPrevDayEntry 4 } 
+
+
+jnxoptIfOMSnSinkPrevDayLastOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power at the output 
+      during the previous 24-hour interval." 
+    ::= { jnxoptIfOMSnSinkPrevDayEntry 5 } 
+
+
+jnxoptIfOMSnSinkPrevDayLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power at the output 
+      during the previous 24-hour interval." 
+    ::= { jnxoptIfOMSnSinkPrevDayEntry 6 } 
+
+
+jnxoptIfOMSnSinkPrevDayHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power at the output 
+      during the previous 24-hour interval." 
+    ::= { jnxoptIfOMSnSinkPrevDayEntry 7 } 
+
+
+-- OMSn source current table 
+-- Contains data for the current 15-minute performance monitoring 
+-- interval. 
+
+
+jnxoptIfOMSnSrcCurrentTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOMSnSrcCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OMSn source performance monitoring information for 
+      the current 15-minute interval." 
+    ::= { jnxoptIfOMSn 6 } 
+
+
+jnxoptIfOMSnSrcCurrentEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOMSnSrcCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OMSn source performance 
+      monitoring information of an interface for the current
+      15-minute interval." 
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOMSnSrcCurrentTable 1 } 
+ 
+JnxoptIfOMSnSrcCurrentEntry ::= 
+    SEQUENCE { 
+        jnxoptIfOMSnSrcCurrentSuspectedFlag              TruthValue,
+        jnxoptIfOMSnSrcCurrentOutputPower                Integer32,
+        jnxoptIfOMSnSrcCurrentLowOutputPower             Integer32,
+        jnxoptIfOMSnSrcCurrentHighOutputPower            Integer32,
+        jnxoptIfOMSnSrcCurrentLowerOutputPowerThreshold  Integer32,
+        jnxoptIfOMSnSrcCurrentUpperOutputPowerThreshold  Integer32,
+        jnxoptIfOMSnSrcCurrentAggregatedInputPower       Integer32,
+        jnxoptIfOMSnSrcCurrentLowAggregatedInputPower    Integer32,
+        jnxoptIfOMSnSrcCurrentHighAggregatedInputPower   Integer32,
+        jnxoptIfOMSnSrcCurrentLowerInputPowerThreshold   Integer32,
+        jnxoptIfOMSnSrcCurrentUpperInputPowerThreshold   Integer32 
+    }  
+
+
+jnxoptIfOMSnSrcCurrentSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOMSnSrcCurrentEntry 1 } 
+
+
+jnxoptIfOMSnSrcCurrentOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The optical power monitored at the output." 
+    ::= { jnxoptIfOMSnSrcCurrentEntry 2 } 
+
+
+jnxoptIfOMSnSrcCurrentLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      current 15-minute interval." 
+      ::= { jnxoptIfOMSnSrcCurrentEntry 3 } 
+  
+
+jnxoptIfOMSnSrcCurrentHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      current 15-minute interval." 
+    ::= { jnxoptIfOMSnSrcCurrentEntry 4 } 
+
+
+jnxoptIfOMSnSrcCurrentLowerOutputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The lower limit threshold on output power. If 
+      jnxoptIfOMSnSrcCurrentOutputPower drops to this value or below, 
+      a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOMSnSrcCurrentEntry 5 } 
+
+
+jnxoptIfOMSnSrcCurrentUpperOutputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The upper limit threshold on output power. If 
+      jnxoptIfOMSnSrcCurrentOutputPower reaches or exceeds this value, 
+      a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOMSnSrcCurrentEntry 6 } 
+
+
+jnxoptIfOMSnSrcCurrentAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The aggregated optical power at the input." 
+    ::= { jnxoptIfOMSnSrcCurrentEntry 7 } 
+  
+
+jnxoptIfOMSnSrcCurrentLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power at the input 
+      during the current 15-minute interval." 
+    ::= { jnxoptIfOMSnSrcCurrentEntry 8 } 
+
+
+jnxoptIfOMSnSrcCurrentHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power at the input 
+      during the current 15-minute interval." 
+    ::= { jnxoptIfOMSnSrcCurrentEntry 9 } 
+
+
+jnxoptIfOMSnSrcCurrentLowerInputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The lower limit threshold on aggregated input power. If 
+      jnxoptIfOMSnSrcCurrentAggregatedInputPower drops to this value 
+      or below, a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOMSnSrcCurrentEntry 10 } 
+
+
+jnxoptIfOMSnSrcCurrentUpperInputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The upper limit threshold on aggregated input power. If 
+      jnxoptIfOMSnSrcCurrentAggregatedInputPower reaches or exceeds 
+      this value, a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOMSnSrcCurrentEntry 11 } 
+
+
+-- OMSn source interval table 
+-- Contains data for previous 15-minute performance monitoring 
+-- intervals. 
+
+
+jnxoptIfOMSnSrcIntervalTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOMSnSrcIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of historical OMSn source performance monitoring 
+      information." 
+    ::= { jnxoptIfOMSn 7 } 
+
+
+jnxoptIfOMSnSrcIntervalEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOMSnSrcIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OMSn source performance 
+      monitoring information of an interface during a particular 
+      historical interval."
+    INDEX { ifIndex, jnxoptIfOMSnSrcIntervalNumber } 
+    ::= { jnxoptIfOMSnSrcIntervalTable 1 } 
+ 
+
+JnxoptIfOMSnSrcIntervalEntry ::= 
+    SEQUENCE { 
+        jnxoptIfOMSnSrcIntervalNumber                   JnxoptIfIntervalNumber,
+        jnxoptIfOMSnSrcIntervalSuspectedFlag            TruthValue,
+        jnxoptIfOMSnSrcIntervalLastOutputPower          Integer32,
+        jnxoptIfOMSnSrcIntervalLowOutputPower           Integer32,
+        jnxoptIfOMSnSrcIntervalHighOutputPower          Integer32,
+        jnxoptIfOMSnSrcIntervalLastAggregatedInputPower Integer32,
+        jnxoptIfOMSnSrcIntervalLowAggregatedInputPower  Integer32,
+        jnxoptIfOMSnSrcIntervalHighAggregatedInputPower Integer32
+    }
+ 
+jnxoptIfOMSnSrcIntervalNumber OBJECT-TYPE 
+    SYNTAX JnxoptIfIntervalNumber 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "Uniquely identifies the interval." 
+    ::= { jnxoptIfOMSnSrcIntervalEntry 1 } 
+
+jnxoptIfOMSnSrcIntervalSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOMSnSrcIntervalEntry 2 } 
+
+
+jnxoptIfOMSnSrcIntervalLastOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOMSnSrcIntervalEntry 3 } 
+
+
+jnxoptIfOMSnSrcIntervalLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOMSnSrcIntervalEntry 4 } 
+
+
+jnxoptIfOMSnSrcIntervalHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOMSnSrcIntervalEntry 5 } 
+
+
+jnxoptIfOMSnSrcIntervalLastAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last aggregated optical power at the input 
+      during the interval." 
+    ::= { jnxoptIfOMSnSrcIntervalEntry 6 } 
+
+
+jnxoptIfOMSnSrcIntervalLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power at the input 
+      during the interval." 
+    ::= { jnxoptIfOMSnSrcIntervalEntry 7 } 
+
+
+jnxoptIfOMSnSrcIntervalHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power at the input 
+      during the interval." 
+    ::= { jnxoptIfOMSnSrcIntervalEntry 8 } 
+
+
+-- OMSn source current day table 
+-- Contains data for the current 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOMSnSrcCurDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOMSnSrcCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A table of OMSn source performance monitoring information for 
+      the current 24-hour interval." 
+    ::= { jnxoptIfOMSn 8 } 
+
+
+jnxoptIfOMSnSrcCurDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOMSnSrcCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OMSn source performance 
+      monitoring information of an interface for the current 
+      24-hour interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOMSnSrcCurDayTable 1 } 
+
+
+JnxoptIfOMSnSrcCurDayEntry ::=
+    SEQUENCE { 
+       jnxoptIfOMSnSrcCurDaySuspectedFlag             TruthValue,
+       jnxoptIfOMSnSrcCurDayLowOutputPower            Integer32,
+       jnxoptIfOMSnSrcCurDayHighOutputPower           Integer32,
+       jnxoptIfOMSnSrcCurDayLowAggregatedInputPower   Integer32,
+       jnxoptIfOMSnSrcCurDayHighAggregatedInputPower  Integer32
+    } 
+ 
+
+jnxoptIfOMSnSrcCurDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOMSnSrcCurDayEntry 1 } 
+
+
+jnxoptIfOMSnSrcCurDayLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOMSnSrcCurDayEntry 2 } 
+
+
+jnxoptIfOMSnSrcCurDayHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "The highest optical power monitored at the output during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOMSnSrcCurDayEntry 3 } 
+
+
+jnxoptIfOMSnSrcCurDayLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power at the input 
+      during the current 24-hour interval." 
+    ::= { jnxoptIfOMSnSrcCurDayEntry 4 } 
+
+
+jnxoptIfOMSnSrcCurDayHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power at the input 
+      during the current 24-hour interval." 
+    ::= { jnxoptIfOMSnSrcCurDayEntry 5 } 
+ 
+
+-- OMSn source previous day table 
+-- Contains data for the previous 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOMSnSrcPrevDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOMSnSrcPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OMSn source performance monitoring information for 
+      the previous 24-hour interval." 
+    ::= { jnxoptIfOMSn 9 } 
+ 
+
+jnxoptIfOMSnSrcPrevDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOMSnSrcPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OMSn source performance 
+      monitoring information of an interface for the previous 
+      24-hour interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOMSnSrcPrevDayTable 1 } 
+
+
+
+JnxoptIfOMSnSrcPrevDayEntry ::=
+    SEQUENCE { 
+        jnxoptIfOMSnSrcPrevDaySuspectedFlag             TruthValue,
+        jnxoptIfOMSnSrcPrevDayLastOutputPower           Integer32,
+        jnxoptIfOMSnSrcPrevDayLowOutputPower            Integer32,
+        jnxoptIfOMSnSrcPrevDayHighOutputPower           Integer32,
+        jnxoptIfOMSnSrcPrevDayLastAggregatedInputPower  Integer32,
+        jnxoptIfOMSnSrcPrevDayLowAggregatedInputPower   Integer32,
+        jnxoptIfOMSnSrcPrevDayHighAggregatedInputPower  Integer32
+    }   
+
+
+jnxoptIfOMSnSrcPrevDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOMSnSrcPrevDayEntry 1 } 
+
+
+jnxoptIfOMSnSrcPrevDayLastOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the output during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOMSnSrcPrevDayEntry 2 } 
+
+
+jnxoptIfOMSnSrcPrevDayLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOMSnSrcPrevDayEntry 3 } 
+
+
+jnxoptIfOMSnSrcPrevDayHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOMSnSrcPrevDayEntry 4 } 
+
+
+
+jnxoptIfOMSnSrcPrevDayLastAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last aggregated optical power at the input during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOMSnSrcPrevDayEntry 5 } 
+
+
+jnxoptIfOMSnSrcPrevDayLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power at the input during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOMSnSrcPrevDayEntry 6 } 
+
+
+jnxoptIfOMSnSrcPrevDayHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power at the input during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOMSnSrcPrevDayEntry 7 } 
+
+
+-- the jnxoptIfOChGroup group 
+-- This group handles the configuration and performance monitoring 
+-- information for OChGroup layers. 
+
+
+-- OChGroup config table 
+
+
+jnxoptIfOChGroupConfigTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChGroupConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OChGroup configuration information." 
+    ::= { jnxoptIfOChGroup 1 } 
+
+
+jnxoptIfOChGroupConfigEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChGroupConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A conceptual row that contains OChGroup configuration
+      information of an interface." 
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOChGroupConfigTable 1 } 
+  
+
+JnxoptIfOChGroupConfigEntry ::=
+    SEQUENCE { 
+        jnxoptIfOChGroupDirectionality JnxoptIfDirectionality 
+    } 
+
+
+jnxoptIfOChGroupDirectionality OBJECT-TYPE 
+    SYNTAX JnxoptIfDirectionality 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the directionality of the entity." 
+    ::= { jnxoptIfOChGroupConfigEntry 1 } 
+
+
+-- OChGroup sink current table 
+-- Contains data for the current 15-minute performance monitoring 
+-- interval. 
+
+
+jnxoptIfOChGroupSinkCurrentTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChGroupSinkCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OChGroup sink performance monitoring information for 
+      the current 15-minute interval." 
+    ::= { jnxoptIfOChGroup 2 } 
+
+
+jnxoptIfOChGroupSinkCurrentEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChGroupSinkCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OChGroup sink performance 
+      monitoring information of an interface for the current
+      15-minute interval." 
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOChGroupSinkCurrentTable 1 } 
+
+JnxoptIfOChGroupSinkCurrentEntry ::= 
+    SEQUENCE { 
+        jnxoptIfOChGroupSinkCurrentSuspectedFlag              TruthValue,
+        jnxoptIfOChGroupSinkCurrentAggregatedInputPower       Integer32,
+        jnxoptIfOChGroupSinkCurrentLowAggregatedInputPower    Integer32,
+        jnxoptIfOChGroupSinkCurrentHighAggregatedInputPower   Integer32,
+        jnxoptIfOChGroupSinkCurrentLowerInputPowerThreshold   Integer32,
+        jnxoptIfOChGroupSinkCurrentUpperInputPowerThreshold   Integer32,
+        jnxoptIfOChGroupSinkCurrentOutputPower                Integer32,
+        jnxoptIfOChGroupSinkCurrentLowOutputPower             Integer32,
+        jnxoptIfOChGroupSinkCurrentHighOutputPower            Integer32,
+        jnxoptIfOChGroupSinkCurrentLowerOutputPowerThreshold  Integer32,
+        jnxoptIfOChGroupSinkCurrentUpperOutputPowerThreshold  Integer32
+    } 
+
+
+jnxoptIfOChGroupSinkCurrentSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChGroupSinkCurrentEntry 1 } 
+
+
+jnxoptIfOChGroupSinkCurrentAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The aggregated optical power of all the DWDM input 
+      channels in the OChGroup." 
+    ::= { jnxoptIfOChGroupSinkCurrentEntry 2 } 
+
+
+jnxoptIfOChGroupSinkCurrentLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power of all the DWDM input 
+      channels in the OChGroup during the current 15-minute interval." 
+    ::= { jnxoptIfOChGroupSinkCurrentEntry 3 } 
+
+
+jnxoptIfOChGroupSinkCurrentHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power of all the DWDM input 
+      channels in the OChGroup during the current 15-minute interval." 
+    ::= { jnxoptIfOChGroupSinkCurrentEntry 4 } 
+
+
+
+
+jnxoptIfOChGroupSinkCurrentLowerInputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The lower limit threshold on aggregated input power. If 
+      jnxoptIfOChGroupSinkCurrentAggregatedInputPower drops to this value 
+      or below, a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOChGroupSinkCurrentEntry 5 } 
+
+
+jnxoptIfOChGroupSinkCurrentUpperInputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The upper limit threshold on aggregated input power. If 
+      jnxoptIfOChGroupSinkCurrentAggregatedInputPower reaches or exceeds 
+      this value, a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOChGroupSinkCurrentEntry 6 } 
+
+
+jnxoptIfOChGroupSinkCurrentOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The optical power monitored at the output 
+      in the OChGroup." 
+    ::= { jnxoptIfOChGroupSinkCurrentEntry 7 } 
+
+
+jnxoptIfOChGroupSinkCurrentLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output 
+      in the OChGroup during the current 15-minute interval." 
+    ::= { jnxoptIfOChGroupSinkCurrentEntry 8 } 
+
+
+jnxoptIfOChGroupSinkCurrentHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "The highest optical power monitored at the output 
+      in the OChGroup during the current 15-minute interval." 
+    ::= { jnxoptIfOChGroupSinkCurrentEntry 9 } 
+
+
+jnxoptIfOChGroupSinkCurrentLowerOutputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The lower limit threshold on the output power. If 
+      jnxoptIfOChGroupSinkCurrentOutputPower drops to this value 
+      or below, a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOChGroupSinkCurrentEntry 10 } 
+
+
+jnxoptIfOChGroupSinkCurrentUpperOutputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The upper limit threshold on the output power. If 
+      jnxoptIfOChGroupSinkCurrentOutputPower reaches or exceeds 
+      this value, a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOChGroupSinkCurrentEntry 11 } 
+
+
+-- OChGroup sink interval table 
+-- Contains data for previous 15-minute performance monitoring 
+-- intervals. 
+
+
+jnxoptIfOChGroupSinkIntervalTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChGroupSinkIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of historical OChGroup sink performance monitoring 
+      information." 
+    ::= { jnxoptIfOChGroup 3 } 
+
+
+jnxoptIfOChGroupSinkIntervalEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChGroupSinkIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OChGroup sink performance 
+      monitoring information of an interface during a particular 
+      historical interval."
+    INDEX { ifIndex, jnxoptIfOChGroupSinkIntervalNumber } 
+    ::= { jnxoptIfOChGroupSinkIntervalTable 1 } 
+
+
+JnxoptIfOChGroupSinkIntervalEntry ::=
+    SEQUENCE { 
+        jnxoptIfOChGroupSinkIntervalNumber           JnxoptIfIntervalNumber,
+        jnxoptIfOChGroupSinkIntervalSuspectedFlag            TruthValue,
+        jnxoptIfOChGroupSinkIntervalLastAggregatedInputPower Integer32,
+        jnxoptIfOChGroupSinkIntervalLowAggregatedInputPower  Integer32,
+        jnxoptIfOChGroupSinkIntervalHighAggregatedInputPower Integer32,
+        jnxoptIfOChGroupSinkIntervalLastOutputPower          Integer32,
+        jnxoptIfOChGroupSinkIntervalLowOutputPower           Integer32,
+        jnxoptIfOChGroupSinkIntervalHighOutputPower          Integer32
+    }   
+
+
+jnxoptIfOChGroupSinkIntervalNumber OBJECT-TYPE 
+    SYNTAX JnxoptIfIntervalNumber 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "Uniquely identifies the interval." 
+    ::= { jnxoptIfOChGroupSinkIntervalEntry 1 } 
+
+
+jnxoptIfOChGroupSinkIntervalSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChGroupSinkIntervalEntry 2 } 
+
+
+jnxoptIfOChGroupSinkIntervalLastAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last aggregated optical power of all the DWDM input 
+      channels in the OChGroup during the interval." 
+    ::= { jnxoptIfOChGroupSinkIntervalEntry 3 } 
+  
+
+jnxoptIfOChGroupSinkIntervalLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power of all the DWDM input 
+      channels in the OChGroup during the interval." 
+    ::= { jnxoptIfOChGroupSinkIntervalEntry 4 } 
+
+
+jnxoptIfOChGroupSinkIntervalHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power of all the DWDM input 
+      channels in the OChGroup during the interval." 
+    ::= { jnxoptIfOChGroupSinkIntervalEntry 5 } 
+ 
+
+jnxoptIfOChGroupSinkIntervalLastOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the output 
+      in the OChGroup during the interval." 
+    ::= { jnxoptIfOChGroupSinkIntervalEntry 6 } 
+
+
+jnxoptIfOChGroupSinkIntervalLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output 
+      in the OChGroup during the interval." 
+    ::= { jnxoptIfOChGroupSinkIntervalEntry 7 } 
+
+
+jnxoptIfOChGroupSinkIntervalHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output 
+      in the OChGroup during the interval." 
+    ::= { jnxoptIfOChGroupSinkIntervalEntry 8 } 
+
+
+-- OChGroup sink current day table 
+-- Contains data for the current 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOChGroupSinkCurDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChGroupSinkCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OChGroup sink performance monitoring information for 
+      the current 24-hour interval." 
+    ::= { jnxoptIfOChGroup 4 } 
+
+
+jnxoptIfOChGroupSinkCurDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChGroupSinkCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OChGroup sink performance 
+      monitoring information of an interface for the current 
+      24-hour interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOChGroupSinkCurDayTable 1 } 
+
+
+JnxoptIfOChGroupSinkCurDayEntry ::=
+     SEQUENCE { 
+         jnxoptIfOChGroupSinkCurDaySuspectedFlag             TruthValue,
+         jnxoptIfOChGroupSinkCurDayLowAggregatedInputPower   Integer32,
+         jnxoptIfOChGroupSinkCurDayHighAggregatedInputPower  Integer32,
+         jnxoptIfOChGroupSinkCurDayLowOutputPower            Integer32,
+         jnxoptIfOChGroupSinkCurDayHighOutputPower           Integer32
+    } 
+
+
+jnxoptIfOChGroupSinkCurDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChGroupSinkCurDayEntry 1 } 
+
+
+jnxoptIfOChGroupSinkCurDayLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power of all the DWDM input 
+      channels in the OChGroup during the current 24-hour interval." 
+    ::= { jnxoptIfOChGroupSinkCurDayEntry 2 } 
+ 
+
+jnxoptIfOChGroupSinkCurDayHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power of all the DWDM input 
+      channels in the OChGroup during the current 24-hour interval." 
+    ::= { jnxoptIfOChGroupSinkCurDayEntry 3 } 
+
+
+jnxoptIfOChGroupSinkCurDayLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output 
+      in the OChGroup during the current 24-hour interval." 
+    ::= { jnxoptIfOChGroupSinkCurDayEntry 4 } 
+
+
+jnxoptIfOChGroupSinkCurDayHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output 
+      in the OChGroup during the current 24-hour interval." 
+    ::= { jnxoptIfOChGroupSinkCurDayEntry 5 } 
+  
+
+-- OChGroup sink previous day table 
+-- Contains data for the previous 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOChGroupSinkPrevDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChGroupSinkPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OChGroup sink performance monitoring information for 
+      the previous 24-hour interval." 
+    ::= { jnxoptIfOChGroup 5 } 
+
+
+jnxoptIfOChGroupSinkPrevDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChGroupSinkPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OChGroup sink performance 
+      monitoring information of an interface for the previous 
+      24-hour interval." 
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOChGroupSinkPrevDayTable 1 } 
+
+
+JnxoptIfOChGroupSinkPrevDayEntry ::=
+    SEQUENCE { 
+        jnxoptIfOChGroupSinkPrevDaySuspectedFlag             TruthValue,
+        jnxoptIfOChGroupSinkPrevDayLastAggregatedInputPower  Integer32,
+        jnxoptIfOChGroupSinkPrevDayLowAggregatedInputPower   Integer32,
+        jnxoptIfOChGroupSinkPrevDayHighAggregatedInputPower  Integer32,
+        jnxoptIfOChGroupSinkPrevDayLastOutputPower           Integer32,
+        jnxoptIfOChGroupSinkPrevDayLowOutputPower            Integer32,
+        jnxoptIfOChGroupSinkPrevDayHighOutputPower           Integer32
+    }   
+
+
+jnxoptIfOChGroupSinkPrevDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChGroupSinkPrevDayEntry 1 } 
+
+
+jnxoptIfOChGroupSinkPrevDayLastAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last aggregated optical power of all the DWDM input 
+      channels in the OChGroup during the previous 24-hour interval." 
+    ::= { jnxoptIfOChGroupSinkPrevDayEntry 2 } 
+
+
+jnxoptIfOChGroupSinkPrevDayLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power of all the DWDM input 
+      channels in the OChGroup during the previous 24-hour interval." 
+    ::= { jnxoptIfOChGroupSinkPrevDayEntry 3 } 
+  
+
+jnxoptIfOChGroupSinkPrevDayHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "The highest aggregated optical power of all the DWDM input 
+      channels in the OChGroup during the previous 24-hour interval." 
+    ::= { jnxoptIfOChGroupSinkPrevDayEntry 4 } 
+
+
+jnxoptIfOChGroupSinkPrevDayLastOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the output 
+      in the OChGroup during the previous 24-hour interval." 
+    ::= { jnxoptIfOChGroupSinkPrevDayEntry 5 } 
+  
+
+jnxoptIfOChGroupSinkPrevDayLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output 
+      in the OChGroup during the previous 24-hour interval." 
+    ::= { jnxoptIfOChGroupSinkPrevDayEntry 6 } 
+
+
+jnxoptIfOChGroupSinkPrevDayHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output 
+      in the OChGroup during the previous 24-hour interval." 
+    ::= { jnxoptIfOChGroupSinkPrevDayEntry 7 } 
+ 
+
+-- OChGroup source current table 
+-- Contains data for the current 15-minute performance monitoring 
+-- interval. 
+
+
+jnxoptIfOChGroupSrcCurrentTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChGroupSrcCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OChGroup source performance monitoring information for 
+      the current 15-minute interval." 
+    ::= { jnxoptIfOChGroup 6 } 
+  
+
+jnxoptIfOChGroupSrcCurrentEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChGroupSrcCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OChGroup source performance 
+      monitoring information of an interface for the current 
+      15-minute interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOChGroupSrcCurrentTable 1 } 
+
+
+JnxoptIfOChGroupSrcCurrentEntry ::=
+    SEQUENCE { 
+        jnxoptIfOChGroupSrcCurrentSuspectedFlag              TruthValue,
+        jnxoptIfOChGroupSrcCurrentOutputPower                Integer32,
+        jnxoptIfOChGroupSrcCurrentLowOutputPower             Integer32,
+        jnxoptIfOChGroupSrcCurrentHighOutputPower            Integer32,
+        jnxoptIfOChGroupSrcCurrentLowerOutputPowerThreshold  Integer32,
+        jnxoptIfOChGroupSrcCurrentUpperOutputPowerThreshold  Integer32,
+        jnxoptIfOChGroupSrcCurrentAggregatedInputPower       Integer32,
+        jnxoptIfOChGroupSrcCurrentLowAggregatedInputPower    Integer32,
+        jnxoptIfOChGroupSrcCurrentHighAggregatedInputPower   Integer32,
+        jnxoptIfOChGroupSrcCurrentLowerInputPowerThreshold   Integer32,
+        jnxoptIfOChGroupSrcCurrentUpperInputPowerThreshold   Integer32 
+    } 
+ 
+
+jnxoptIfOChGroupSrcCurrentSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChGroupSrcCurrentEntry 1 } 
+
+
+jnxoptIfOChGroupSrcCurrentOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The optical power monitored at the output." 
+    ::= { jnxoptIfOChGroupSrcCurrentEntry 2 } 
+  
+
+jnxoptIfOChGroupSrcCurrentLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "The lowest optical power monitored at the output during the 
+      current 15-minute interval." 
+    ::= { jnxoptIfOChGroupSrcCurrentEntry 3 } 
+
+
+jnxoptIfOChGroupSrcCurrentHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      current 15-minute interval." 
+    ::= { jnxoptIfOChGroupSrcCurrentEntry 4 } 
+ 
+
+jnxoptIfOChGroupSrcCurrentLowerOutputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The lower limit threshold on output power. If 
+      jnxoptIfOChGroupSrcCurrentOutputPower drops to this value or below, 
+      a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOChGroupSrcCurrentEntry 5 } 
+
+
+jnxoptIfOChGroupSrcCurrentUpperOutputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The upper limit threshold on output power. If 
+      jnxoptIfOChGroupSrcCurrentOutputPower reaches or exceeds this value, 
+      a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOChGroupSrcCurrentEntry 6 } 
+
+
+jnxoptIfOChGroupSrcCurrentAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The aggregated optical power monitored at the input." 
+    ::= { jnxoptIfOChGroupSrcCurrentEntry 7 } 
+   
+
+jnxoptIfOChGroupSrcCurrentLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power monitored at the input 
+      during the current 15-minute interval." 
+    ::= { jnxoptIfOChGroupSrcCurrentEntry 8 } 
+
+
+jnxoptIfOChGroupSrcCurrentHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power monitored at the input 
+      during the current 15-minute interval." 
+    ::= { jnxoptIfOChGroupSrcCurrentEntry 9 } 
+
+
+jnxoptIfOChGroupSrcCurrentLowerInputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The lower limit threshold on input power. If 
+      jnxoptIfOChGroupSrcCurrentAggregatedInputPower drops to this value 
+      or below, a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOChGroupSrcCurrentEntry 10 } 
+
+
+jnxoptIfOChGroupSrcCurrentUpperInputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The upper limit threshold on input power. If 
+      jnxoptIfOChGroupSrcCurrentAggregatedInputPower reaches or exceeds 
+      this value, a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOChGroupSrcCurrentEntry 11 } 
+
+
+-- OChGroup source interval table 
+-- Contains data for previous 15-minute performance monitoring 
+-- intervals. 
+
+
+jnxoptIfOChGroupSrcIntervalTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChGroupSrcIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A table of historical OChGroup source performance monitoring 
+      information." 
+    ::= { jnxoptIfOChGroup 7 } 
+
+
+jnxoptIfOChGroupSrcIntervalEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChGroupSrcIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OChGroup source performance 
+      monitoring information of an interface during a particular 
+      historical interval."
+    INDEX { ifIndex, jnxoptIfOChGroupSrcIntervalNumber } 
+    ::= { jnxoptIfOChGroupSrcIntervalTable 1 } 
+
+
+JnxoptIfOChGroupSrcIntervalEntry ::=
+    SEQUENCE { 
+        jnxoptIfOChGroupSrcIntervalNumber               JnxoptIfIntervalNumber,
+        jnxoptIfOChGroupSrcIntervalSuspectedFlag            TruthValue,
+        jnxoptIfOChGroupSrcIntervalLastOutputPower          Integer32,
+        jnxoptIfOChGroupSrcIntervalLowOutputPower           Integer32,
+        jnxoptIfOChGroupSrcIntervalHighOutputPower          Integer32,
+        jnxoptIfOChGroupSrcIntervalLastAggregatedInputPower Integer32,
+        jnxoptIfOChGroupSrcIntervalLowAggregatedInputPower  Integer32,
+        jnxoptIfOChGroupSrcIntervalHighAggregatedInputPower Integer32 
+     } 
+
+
+jnxoptIfOChGroupSrcIntervalNumber OBJECT-TYPE 
+    SYNTAX JnxoptIfIntervalNumber 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "Uniquely identifies the interval." 
+    ::= { jnxoptIfOChGroupSrcIntervalEntry 1 } 
+
+
+jnxoptIfOChGroupSrcIntervalSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChGroupSrcIntervalEntry 2 } 
+
+
+jnxoptIfOChGroupSrcIntervalLastOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "The last optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOChGroupSrcIntervalEntry 3 } 
+
+
+jnxoptIfOChGroupSrcIntervalLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOChGroupSrcIntervalEntry 4 } 
+
+
+jnxoptIfOChGroupSrcIntervalHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOChGroupSrcIntervalEntry 5 } 
+
+
+jnxoptIfOChGroupSrcIntervalLastAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last aggregated optical power monitored at the input 
+      during the interval." 
+    ::= { jnxoptIfOChGroupSrcIntervalEntry 6 } 
+ 
+
+jnxoptIfOChGroupSrcIntervalLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power monitored at the input 
+      during the interval." 
+    ::= { jnxoptIfOChGroupSrcIntervalEntry 7 } 
+
+
+jnxoptIfOChGroupSrcIntervalHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power monitored at the input 
+      during the interval." 
+    ::= { jnxoptIfOChGroupSrcIntervalEntry 8 } 
+
+
+-- OChGroup source current day table 
+-- Contains data for the current 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOChGroupSrcCurDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChGroupSrcCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OChGroup source performance monitoring information for 
+      the current 24-hour interval." 
+    ::= { jnxoptIfOChGroup 8 } 
+
+
+jnxoptIfOChGroupSrcCurDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChGroupSrcCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OChGroup source performance 
+      monitoring information of an interface for the current 
+      24-hour interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOChGroupSrcCurDayTable 1 } 
+
+
+JnxoptIfOChGroupSrcCurDayEntry ::=
+    SEQUENCE { 
+        jnxoptIfOChGroupSrcCurDaySuspectedFlag             TruthValue,
+        jnxoptIfOChGroupSrcCurDayLowOutputPower            Integer32,
+        jnxoptIfOChGroupSrcCurDayHighOutputPower           Integer32,
+        jnxoptIfOChGroupSrcCurDayLowAggregatedInputPower   Integer32,
+        jnxoptIfOChGroupSrcCurDayHighAggregatedInputPower  Integer32
+    } 
+
+
+jnxoptIfOChGroupSrcCurDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChGroupSrcCurDayEntry 1 } 
+
+
+jnxoptIfOChGroupSrcCurDayLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOChGroupSrcCurDayEntry 2 } 
+
+
+jnxoptIfOChGroupSrcCurDayHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOChGroupSrcCurDayEntry 3 } 
+
+
+jnxoptIfOChGroupSrcCurDayLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power monitored at the input 
+      during the current 24-hour interval." 
+    ::= { jnxoptIfOChGroupSrcCurDayEntry 4 } 
+
+
+jnxoptIfOChGroupSrcCurDayHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power monitored at the input 
+      during the current 24-hour interval." 
+    ::= { jnxoptIfOChGroupSrcCurDayEntry 5 } 
+
+
+-- OChGroup source previous day table 
+-- Contains data for the previous 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOChGroupSrcPrevDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChGroupSrcPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A table of OChGroup source performance monitoring information for 
+      the previous 24-hour interval." 
+    ::= { jnxoptIfOChGroup 9 } 
+
+
+jnxoptIfOChGroupSrcPrevDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChGroupSrcPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OChGroup source performance 
+      monitoring information of an interface for the previous 
+      24-hour interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOChGroupSrcPrevDayTable 1 } 
+
+
+JnxoptIfOChGroupSrcPrevDayEntry ::=
+
+
+    SEQUENCE { 
+        jnxoptIfOChGroupSrcPrevDaySuspectedFlag            TruthValue, 
+        jnxoptIfOChGroupSrcPrevDayLastOutputPower          Integer32, 
+        jnxoptIfOChGroupSrcPrevDayLowOutputPower           Integer32, 
+        jnxoptIfOChGroupSrcPrevDayHighOutputPower          Integer32, 
+        jnxoptIfOChGroupSrcPrevDayLastAggregatedInputPower Integer32, 
+        jnxoptIfOChGroupSrcPrevDayLowAggregatedInputPower  Integer32, 
+        jnxoptIfOChGroupSrcPrevDayHighAggregatedInputPower Integer32 
+    } 
+
+
+jnxoptIfOChGroupSrcPrevDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChGroupSrcPrevDayEntry 1 } 
+
+
+jnxoptIfOChGroupSrcPrevDayLastOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the output during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOChGroupSrcPrevDayEntry 2 } 
+
+
+jnxoptIfOChGroupSrcPrevDayLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOChGroupSrcPrevDayEntry 3 } 
+
+
+jnxoptIfOChGroupSrcPrevDayHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOChGroupSrcPrevDayEntry 4 } 
+
+
+jnxoptIfOChGroupSrcPrevDayLastAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last aggregated optical power monitored at the input 
+      during the previous 24-hour interval." 
+    ::= { jnxoptIfOChGroupSrcPrevDayEntry 5 } 
+
+
+jnxoptIfOChGroupSrcPrevDayLowAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest aggregated optical power monitored at the input 
+      during the previous 24-hour interval." 
+    ::= { jnxoptIfOChGroupSrcPrevDayEntry 6 } 
+
+
+jnxoptIfOChGroupSrcPrevDayHighAggregatedInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest aggregated optical power monitored at the input 
+      during the previous 24-hour interval." 
+    ::= { jnxoptIfOChGroupSrcPrevDayEntry 7 } 
+
+
+-- the jnxoptIfOCh group 
+
+
+-- This group handles the configuration and 
+-- performance monitoring information for OCh layers. 
+
+
+-- OCh config table 
+
+
+jnxoptIfOChConfigTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OCh configuration information." 
+    ::= { jnxoptIfOCh 1 } 
+
+
+jnxoptIfOChConfigEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OCh configuration
+      information of an interface." 
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOChConfigTable 1 } 
+ 
+
+JnxoptIfOChConfigEntry ::=
+    SEQUENCE { 
+        jnxoptIfOChDirectionality JnxoptIfDirectionality, 
+        jnxoptIfOChCurrentStatus  BITS  
+    } 
+
+
+jnxoptIfOChDirectionality OBJECT-TYPE 
+    SYNTAX JnxoptIfDirectionality 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the directionality of the entity." 
+    ::= { jnxoptIfOChConfigEntry 1 } 
+
+
+jnxoptIfOChCurrentStatus OBJECT-TYPE
+    SYNTAX BITS { 
+        losP(0), 
+        los(1), 
+        oci(2), 
+        ssfP(3), 
+        ssfO(4), 
+        ssf(5) 
+    }
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the defect condition of the entity, if any. 
+      This object is applicable when jnxoptIfOChDirectionality 
+      has the value sink(1) or bidirectional(3). 
+      In full-capability systems the bit position los(1) is not used. 
+      In reduced-capability systems or at IrDI interfaces only 
+      the bit positions los(1) and ssfP(3) are used."
+    ::= { jnxoptIfOChConfigEntry 2 } 
+
+
+-- OCh sink current table 
+-- Contains data for the current 15-minute performance monitoring 
+-- interval. 
+
+
+jnxoptIfOChSinkCurrentTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChSinkCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OCh sink performance monitoring information for 
+      the current 15-minute interval." 
+    ::= { jnxoptIfOCh 2 } 
+
+
+jnxoptIfOChSinkCurrentEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChSinkCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OCh sink performance 
+      monitoring information for an interface for the current 
+      15-minute interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOChSinkCurrentTable 1 } 
+
+
+JnxoptIfOChSinkCurrentEntry ::=
+    SEQUENCE { 
+        jnxoptIfOChSinkCurrentSuspectedFlag            TruthValue, 
+        jnxoptIfOChSinkCurrentInputPower               Integer32, 
+        jnxoptIfOChSinkCurrentLowInputPower            Integer32, 
+        jnxoptIfOChSinkCurrentHighInputPower           Integer32, 
+        jnxoptIfOChSinkCurrentLowerInputPowerThreshold Integer32, 
+        jnxoptIfOChSinkCurrentUpperInputPowerThreshold Integer32 
+    } 
+
+
+jnxoptIfOChSinkCurrentSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChSinkCurrentEntry 1 } 
+
+
+jnxoptIfOChSinkCurrentInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The optical power monitored at the input." 
+    ::= { jnxoptIfOChSinkCurrentEntry 2 } 
+
+
+jnxoptIfOChSinkCurrentLowInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the input during the 
+      current 15-minute interval." 
+    ::= { jnxoptIfOChSinkCurrentEntry 3 } 
+
+
+jnxoptIfOChSinkCurrentHighInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the input during the 
+      current 15-minute interval." 
+    ::= { jnxoptIfOChSinkCurrentEntry 4 } 
+
+
+jnxoptIfOChSinkCurrentLowerInputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The lower limit threshold on input power. If 
+      jnxoptIfOChSinkCurrentInputPower drops to this value or below, 
+      a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOChSinkCurrentEntry 5 } 
+
+
+jnxoptIfOChSinkCurrentUpperInputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The upper limit threshold on input power. If 
+      jnxoptIfOChSinkCurrentInputPower reaches or exceeds this value, 
+      a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOChSinkCurrentEntry 6 } 
+
+
+-- OCh sink interval table 
+-- Contains data for previous 15-minute performance monitoring 
+-- intervals. 
+
+
+jnxoptIfOChSinkIntervalTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChSinkIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of historical OCh sink performance monitoring 
+      information." 
+    ::= { jnxoptIfOCh 3 } 
+
+
+jnxoptIfOChSinkIntervalEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChSinkIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OCh sink performance 
+      monitoring information of an interface during a particular 
+      historical interval."
+    INDEX { ifIndex, jnxoptIfOChSinkIntervalNumber } 
+    ::= { jnxoptIfOChSinkIntervalTable 1 } 
+
+
+JnxoptIfOChSinkIntervalEntry ::=
+    SEQUENCE { 
+        jnxoptIfOChSinkIntervalNumber          JnxoptIfIntervalNumber,
+        jnxoptIfOChSinkIntervalSuspectedFlag   TruthValue,
+        jnxoptIfOChSinkIntervalLastInputPower  Integer32,
+        jnxoptIfOChSinkIntervalLowInputPower   Integer32,
+        jnxoptIfOChSinkIntervalHighInputPower  Integer32
+    } 
+
+
+jnxoptIfOChSinkIntervalNumber OBJECT-TYPE 
+    SYNTAX JnxoptIfIntervalNumber 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "Uniquely identifies the interval." 
+    ::= { jnxoptIfOChSinkIntervalEntry 1 } 
+  
+
+jnxoptIfOChSinkIntervalSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChSinkIntervalEntry 2 } 
+ 
+
+jnxoptIfOChSinkIntervalLastInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the input during the 
+      interval." 
+    ::= { jnxoptIfOChSinkIntervalEntry 3 } 
+
+
+jnxoptIfOChSinkIntervalLowInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the input during the 
+      interval." 
+    ::= { jnxoptIfOChSinkIntervalEntry 4 } 
+
+
+jnxoptIfOChSinkIntervalHighInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the input during the 
+      interval." 
+    ::= { jnxoptIfOChSinkIntervalEntry 5 } 
+
+
+-- OCh sink current day table 
+-- Contains data for the current 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOChSinkCurDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChSinkCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OCh sink performance monitoring information for 
+      the current 24-hour interval." 
+    ::= { jnxoptIfOCh 4 } 
+
+
+jnxoptIfOChSinkCurDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChSinkCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OCh sink performance 
+      monitoring information of an interface for the current 
+      24-hour interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOChSinkCurDayTable 1 } 
+
+
+JnxoptIfOChSinkCurDayEntry ::=
+    SEQUENCE { 
+        jnxoptIfOChSinkCurDaySuspectedFlag   TruthValue,
+        jnxoptIfOChSinkCurDayLowInputPower   Integer32,
+        jnxoptIfOChSinkCurDayHighInputPower  Integer32 
+    } 
+
+
+jnxoptIfOChSinkCurDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChSinkCurDayEntry 1 } 
+
+
+jnxoptIfOChSinkCurDayLowInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the input during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOChSinkCurDayEntry 2 } 
+
+
+jnxoptIfOChSinkCurDayHighInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+    "The highest optical power monitored at the input during the 
+    current 24-hour interval." 
+    ::= { jnxoptIfOChSinkCurDayEntry 3 } 
+
+
+
+-- OCh sink previous day table 
+-- Contains data for the previous 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOChSinkPrevDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChSinkPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OCh sink performance monitoring information for 
+      the previous 24-hour interval." 
+    ::= { jnxoptIfOCh 5 } 
+
+
+jnxoptIfOChSinkPrevDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChSinkPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OCh sink performance 
+      monitoring information of an interface for the previous 
+      24-hour interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOChSinkPrevDayTable 1 } 
+
+
+JnxoptIfOChSinkPrevDayEntry ::=
+    SEQUENCE { 
+        jnxoptIfOChSinkPrevDaySuspectedFlag   TruthValue,
+        jnxoptIfOChSinkPrevDayLastInputPower  Integer32,
+        jnxoptIfOChSinkPrevDayLowInputPower   Integer32,
+        jnxoptIfOChSinkPrevDayHighInputPower  Integer32 
+    }   
+
+
+jnxoptIfOChSinkPrevDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChSinkPrevDayEntry 1 } 
+
+
+jnxoptIfOChSinkPrevDayLastInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the input during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOChSinkPrevDayEntry 2 } 
+
+
+jnxoptIfOChSinkPrevDayLowInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the input during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOChSinkPrevDayEntry 3 } 
+
+
+jnxoptIfOChSinkPrevDayHighInputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the input during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOChSinkPrevDayEntry 4 } 
+
+
+-- OCh source current table 
+-- Contains data for the current 15-minute performance monitoring 
+-- interval. 
+
+
+jnxoptIfOChSrcCurrentTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChSrcCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OCh source performance monitoring information for 
+      the current 15-minute interval." 
+    ::= { jnxoptIfOCh 6 } 
+
+
+jnxoptIfOChSrcCurrentEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChSrcCurrentEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OCh source performance 
+      monitoring information of an interface for the current 
+      15-minute interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOChSrcCurrentTable 1 } 
+
+
+JnxoptIfOChSrcCurrentEntry ::= 
+    SEQUENCE {    
+        jnxoptIfOChSrcCurrentSuspectedFlag              TruthValue,
+        jnxoptIfOChSrcCurrentOutputPower                Integer32,
+        jnxoptIfOChSrcCurrentLowOutputPower             Integer32,
+        jnxoptIfOChSrcCurrentHighOutputPower            Integer32,
+        jnxoptIfOChSrcCurrentLowerOutputPowerThreshold  Integer32,
+        jnxoptIfOChSrcCurrentUpperOutputPowerThreshold  Integer32 
+    } 
+
+
+jnxoptIfOChSrcCurrentSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChSrcCurrentEntry 1 } 
+
+
+jnxoptIfOChSrcCurrentOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The optical power monitored at the output." 
+    ::= { jnxoptIfOChSrcCurrentEntry 2 } 
+
+
+jnxoptIfOChSrcCurrentLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      current 15-minute interval." 
+   ::= { jnxoptIfOChSrcCurrentEntry 3 } 
+
+
+jnxoptIfOChSrcCurrentHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      current 15-minute interval." 
+    ::= { jnxoptIfOChSrcCurrentEntry 4 } 
+
+
+jnxoptIfOChSrcCurrentLowerOutputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The lower limit threshold on output power. If 
+      jnxoptIfOChSrcCurrentOutputPower drops to this value or below, 
+      a Threshold Crossing Alert (TCA) should be sent."
+    ::= { jnxoptIfOChSrcCurrentEntry 5 } 
+
+
+jnxoptIfOChSrcCurrentUpperOutputPowerThreshold OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The upper limit threshold on output power. If 
+      jnxoptIfOChSrcCurrentOutputPower reaches or exceeds this value, 
+      a Threshold Crossing Alert (TCA) should be sent."
+      ::= { jnxoptIfOChSrcCurrentEntry 6 } 
+
+
+-- OCh source interval table 
+-- Contains data for previous 15-minute performance monitoring 
+-- intervals. 
+
+
+jnxoptIfOChSrcIntervalTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChSrcIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of historical OCh source performance monitoring 
+      information." 
+    ::= { jnxoptIfOCh 7 } 
+
+
+jnxoptIfOChSrcIntervalEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChSrcIntervalEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OCh source performance 
+      monitoring information of an interface during a particular 
+      historical interval."
+    INDEX { ifIndex, jnxoptIfOChSrcIntervalNumber } 
+    ::= { jnxoptIfOChSrcIntervalTable 1 } 
+
+
+JnxoptIfOChSrcIntervalEntry ::=
+    SEQUENCE { 
+        jnxoptIfOChSrcIntervalNumber           JnxoptIfIntervalNumber,
+        jnxoptIfOChSrcIntervalSuspectedFlag    TruthValue,
+        jnxoptIfOChSrcIntervalLastOutputPower  Integer32,
+        jnxoptIfOChSrcIntervalLowOutputPower   Integer32,
+        jnxoptIfOChSrcIntervalHighOutputPower  Integer32
+    } 
+
+
+jnxoptIfOChSrcIntervalNumber OBJECT-TYPE 
+    SYNTAX JnxoptIfIntervalNumber 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "Uniquely identifies the interval." 
+    ::= { jnxoptIfOChSrcIntervalEntry 1 } 
+
+
+jnxoptIfOChSrcIntervalSuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChSrcIntervalEntry 2 } 
+
+
+jnxoptIfOChSrcIntervalLastOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOChSrcIntervalEntry 3 } 
+
+
+jnxoptIfOChSrcIntervalLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOChSrcIntervalEntry 4 } 
+
+
+jnxoptIfOChSrcIntervalHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      interval." 
+    ::= { jnxoptIfOChSrcIntervalEntry 5 } 
+ 
+
+-- OCh source current day table 
+-- Contains data for the current 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOChSrcCurDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChSrcCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OCh source performance monitoring information for 
+      the current 24-hour interval." 
+      ::= { jnxoptIfOCh 8 } 
+
+
+jnxoptIfOChSrcCurDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChSrcCurDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OCh source performance 
+      monitoring information of an interface for the current 
+      24-hour interval."
+     INDEX { ifIndex } 
+   ::= { jnxoptIfOChSrcCurDayTable 1 } 
+ 
+
+JnxoptIfOChSrcCurDayEntry ::=
+    SEQUENCE { 
+        jnxoptIfOChSrcCurDaySuspectedFlag   TruthValue, 
+        jnxoptIfOChSrcCurDayLowOutputPower  Integer32, 
+        jnxoptIfOChSrcCurDayHighOutputPower Integer32 
+    } 
+
+
+jnxoptIfOChSrcCurDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChSrcCurDayEntry 1 } 
+ 
+
+jnxoptIfOChSrcCurDayLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOChSrcCurDayEntry 2 } 
+
+
+jnxoptIfOChSrcCurDayHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+      current 24-hour interval." 
+    ::= { jnxoptIfOChSrcCurDayEntry 3 } 
+
+
+-- OCh source previous day table 
+-- Contains data for the previous 24-hour performance 
+-- monitoring interval. 
+
+
+jnxoptIfOChSrcPrevDayTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOChSrcPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OCh source performance monitoring information for 
+      the previous 24-hour interval." 
+    ::= { jnxoptIfOCh 9 } 
+
+
+jnxoptIfOChSrcPrevDayEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOChSrcPrevDayEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OCh source performance 
+      monitoring information of an interface for the previous 
+      24-hour interval."
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOChSrcPrevDayTable 1 } 
+
+
+JnxoptIfOChSrcPrevDayEntry ::=
+    SEQUENCE { 
+        jnxoptIfOChSrcPrevDaySuspectedFlag    TruthValue,
+        jnxoptIfOChSrcPrevDayLastOutputPower  Integer32,
+        jnxoptIfOChSrcPrevDayLowOutputPower   Integer32,
+        jnxoptIfOChSrcPrevDayHighOutputPower  Integer32
+    } 
+
+
+jnxoptIfOChSrcPrevDaySuspectedFlag OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "If true, the data in this entry may be unreliable." 
+    ::= { jnxoptIfOChSrcPrevDayEntry 1 } 
+
+
+jnxoptIfOChSrcPrevDayLastOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The last optical power monitored at the output during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOChSrcPrevDayEntry 2 } 
+
+
+jnxoptIfOChSrcPrevDayLowOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The lowest optical power monitored at the output during the 
+      previous 24-hour interval." 
+    ::= { jnxoptIfOChSrcPrevDayEntry 3 } 
+
+
+jnxoptIfOChSrcPrevDayHighOutputPower OBJECT-TYPE 
+    SYNTAX Integer32 
+    UNITS "0.1 dbm" 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The highest optical power monitored at the output during the 
+       previous 24-hour interval." 
+    ::= { jnxoptIfOChSrcPrevDayEntry 4 } 
+  
+
+-- the jnxoptIfOTUk group 
+-- This group handles the configuration 
+-- information for OTUk layers. 
+
+
+-- OTUk config table 
+
+
+jnxoptIfOTUkConfigTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfOTUkConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of OTUk configuration information." 
+    ::= { jnxoptIfOTUk 1 } 
+
+
+
+jnxoptIfOTUkConfigEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfOTUkConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains OTUk configuration
+      information of an interface." 
+    INDEX { ifIndex } 
+    ::= { jnxoptIfOTUkConfigTable 1 } 
+
+
+JnxoptIfOTUkConfigEntry ::=
+    SEQUENCE { 
+        jnxoptIfOTUkDirectionality              JnxoptIfDirectionality,
+        jnxoptIfOTUkBitRateK                    JnxoptIfBitRateK,
+        jnxoptIfOTUkTraceIdentifierTransmitted  JnxoptIfTxTI,
+        jnxoptIfOTUkDAPIExpected                JnxoptIfExDAPI,
+        jnxoptIfOTUkSAPIExpected                JnxoptIfExSAPI,
+        jnxoptIfOTUkTraceIdentifierAccepted     JnxoptIfAcTI,
+        jnxoptIfOTUkTIMDetMode                  JnxoptIfTIMDetMode,
+        jnxoptIfOTUkTIMActEnabled               TruthValue,
+        jnxoptIfOTUkDEGThr                      JnxoptIfDEGThr,
+        jnxoptIfOTUkDEGM                        JnxoptIfDEGM,
+        jnxoptIfOTUkSinkAdaptActive             TruthValue,
+        jnxoptIfOTUkSourceAdaptActive           TruthValue,
+        jnxoptIfOTUkSinkFECEnabled              TruthValue,
+        jnxoptIfOTUkCurrentStatus               BITS
+    } 
+
+
+jnxoptIfOTUkDirectionality OBJECT-TYPE 
+    SYNTAX JnxoptIfDirectionality 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the directionality of the entity." 
+    ::= { jnxoptIfOTUkConfigEntry 1 } 
+
+
+jnxoptIfOTUkBitRateK OBJECT-TYPE 
+    SYNTAX JnxoptIfBitRateK 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the bit rate of the entity." 
+    ::= { jnxoptIfOTUkConfigEntry 2 } 
+
+
+jnxoptIfOTUkTraceIdentifierTransmitted OBJECT-TYPE 
+    SYNTAX JnxoptIfTxTI 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The trace identifier transmitted. 
+      This object is applicable when jnxoptIfOTUkDirectionality 
+      has the value source(2) or bidirectional(3). It must not 
+      be instantiated in rows where jnxoptIfOTUkDirectionality 
+      has the value sink(1). 
+      If no value is ever set by a management entity for this 
+      object, system-specific default value will be used. 
+      Any implementation that instantiates this object must 
+      document the system-specific default value or how it 
+      is derived."
+    ::= { jnxoptIfOTUkConfigEntry 3 } 
+
+
+jnxoptIfOTUkDAPIExpected OBJECT-TYPE 
+    SYNTAX JnxoptIfExDAPI 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The DAPI expected by the receiver. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfOTUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfOTUkDirectionality has the value source(2). 
+      This object has no effect when jnxoptIfOTUkTIMDetMode has 
+      the value off(1)."
+    ::= { jnxoptIfOTUkConfigEntry 4 } 
+
+
+jnxoptIfOTUkSAPIExpected OBJECT-TYPE 
+    SYNTAX JnxoptIfExSAPI 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The SAPI expected by the receiver. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfOTUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfOTUkDirectionality has the value source(2). 
+      This object has no effect when jnxoptIfOTUkTIMDetMode has 
+      the value off(1)."
+    ::= { jnxoptIfOTUkConfigEntry 5 } 
+
+
+jnxoptIfOTUkTraceIdentifierAccepted OBJECT-TYPE 
+    SYNTAX JnxoptIfAcTI 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The actual trace identifier accepted. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfOTUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfOTUkDirectionality has the value source(2). 
+      The value of this object is unspecified when 
+      jnxoptIfOTUkCurrentStatus indicates a near-end defect 
+      (i.e., ssf(3), lof(4), ais(5), lom(6)) that prevents 
+      extraction of the trace message."
+    ::= { jnxoptIfOTUkConfigEntry 6 } 
+
+
+jnxoptIfOTUkTIMDetMode OBJECT-TYPE 
+    SYNTAX JnxoptIfTIMDetMode 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the mode of the Trace Identifier Mismatch (TIM) 
+      Detection function. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfOTUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfOTUkDirectionality has the value source(2). 
+      The default value of this object is off(1)." 
+    ::= { jnxoptIfOTUkConfigEntry 7 } 
+
+
+jnxoptIfOTUkTIMActEnabled OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates whether the Trace Identifier Mismatch (TIM) 
+      Consequent Action function is enabled. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfOTUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfOTUkDirectionality has the value source(2). 
+      This object has no effect when jnxoptIfOTUkTIMDetMode has 
+      the value off(1). 
+      The default value of this object is false(2)." 
+    ::= { jnxoptIfOTUkConfigEntry 8 } 
+
+
+jnxoptIfOTUkDEGThr OBJECT-TYPE 
+    SYNTAX JnxoptIfDEGThr 
+    UNITS "percentage" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the threshold level for declaring a performance 
+      monitoring (PM) Second to be bad. A PM Second is declared bad if 
+      the percentage of detected errored blocks in that second is 
+      greater than or equal to jnxoptIfOTUkDEGThr. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfOTUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfOTUkDirectionality has the value source(2). 
+      The default value of this object is Severely Errored Second 
+      (SES) Estimator (See ITU-T G.7710)."
+    ::= { jnxoptIfOTUkConfigEntry 9 } 
+
+
+jnxoptIfOTUkDEGM OBJECT-TYPE 
+    SYNTAX JnxoptIfDEGM 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the threshold level for declaring a Degraded Signal 
+      defect (dDEG). A dDEG shall be declared if jnxoptIfOTUkDEGM 
+      consecutive bad PM Seconds are detected. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfOTUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfOTUkDirectionality has the value source(2). 
+      The default value of this object is 7 (See ITU-T G.7710)."
+    ::= { jnxoptIfOTUkConfigEntry 10 } 
+
+
+jnxoptIfOTUkSinkAdaptActive OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "Indicates whether the sink adaptation function is activated or 
+      not. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfOTUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfOTUkDirectionality has the value source(2). 
+      The default value of this object is false(2)."
+    ::= { jnxoptIfOTUkConfigEntry 11 } 
+
+
+jnxoptIfOTUkSourceAdaptActive OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "Indicates whether the source adaptation function is activated or 
+      not. 
+      This object is only applicable to the source function, i.e., 
+      only when jnxoptIfOTUkDirectionality has the value source(2) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfOTUkDirectionality has the value sink(1). 
+      The default value of this object is false(2)." 
+    ::= { jnxoptIfOTUkConfigEntry 12 } 
+
+
+jnxoptIfOTUkSinkFECEnabled OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION 
+      "If Forward Error Correction (FEC) is supported, this object 
+      indicates whether FEC at the OTUk sink adaptation function is 
+      enabled or not. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfOTUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfOTUkDirectionality has the value source(2). 
+      The default value of this object is true(1)." 
+    ::= { jnxoptIfOTUkConfigEntry 13 } 
+
+
+jnxoptIfOTUkCurrentStatus OBJECT-TYPE 
+    SYNTAX BITS { 
+        tim(0), 
+        deg(1), 
+        bdi(2), 
+        ssf(3), 
+        lof(4), 
+        ais(5), 
+        lom(6) 
+    } 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the defect condition of the entity, if any. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfOTUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfOTUkDirectionality has the value source(2)." 
+    ::= { jnxoptIfOTUkConfigEntry 14 } 
+
+
+-- GCC0 config table 
+
+
+jnxoptIfGCC0ConfigTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfGCC0ConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A table of GCC0 configuration information." 
+    ::= { jnxoptIfOTUk 2 } 
+
+
+jnxoptIfGCC0ConfigEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfGCC0ConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains GCC0 configuration 
+      information of an interface. Each instance must 
+      correspond to an instance of jnxoptIfOTUkConfigEntry. 
+      Separate source and/or sink instances may exist 
+      for a given ifIndex value, or a single bidirectional 
+      instance may exist, but a bidirectional instance may 
+      not coexist with a source or sink instance. 
+      Instances of this conceptual row persist across 
+      agent restarts."
+    INDEX { ifIndex, jnxoptIfGCC0Directionality } 
+    ::= { jnxoptIfGCC0ConfigTable 1 } 
+
+
+JnxoptIfGCC0ConfigEntry ::=
+    SEQUENCE { 
+        jnxoptIfGCC0Directionality JnxoptIfDirectionality, 
+        jnxoptIfGCC0Application    SnmpAdminString, 
+        jnxoptIfGCC0RowStatus      RowStatus 
+    } 
+
+
+jnxoptIfGCC0Directionality OBJECT-TYPE 
+    SYNTAX JnxoptIfDirectionality 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the directionality of the entity. 
+      The values source(2) and bidirectional(3) are 
+      not allowed if the corresponding instance of 
+      jnxoptIfOTUkDirectionality has the value sink(1). 
+      The values sink(1) and bidirectional(3) are 
+      not allowed if the corresponding instance of 
+      jnxoptIfOTUkDirectionality has the value source(2)."
+    ::= { jnxoptIfGCC0ConfigEntry 1 } 
+
+
+jnxoptIfGCC0Application OBJECT-TYPE 
+    SYNTAX SnmpAdminString 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the application transported by the GCC0 entity. 
+      Example applications are ECC, User data channel.
+      The value of this object may not be changed when 
+      jnxoptIfGCC0RowStatus has the value active(1)." 
+    ::= { jnxoptIfGCC0ConfigEntry 2 } 
+
+
+jnxoptIfGCC0RowStatus OBJECT-TYPE 
+    SYNTAX RowStatus 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "This columnar object is used for creating and deleting a 
+      conceptual row of the jnxoptIfGCC0 config table. 
+      It is used to model the addGCC0Access and removeGCC0Access 
+      operations of an OTUk_TTP for GCC0 access control as defined 
+      in G.874.1. Setting RowStatus to createAndGo or createAndWait 
+      implies addGCC0Access. Setting RowStatus to destroy implies 
+      removeGCC0Access."
+    ::= { jnxoptIfGCC0ConfigEntry 3 } 
+
+
+-- the jnxoptIfODUk group 
+-- This group handles the configuration information 
+-- for the ODUk layers. 
+
+
+-- ODUk config table 
+
+
+jnxoptIfODUkConfigTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfODUkConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of ODUk configuration information." 
+    ::= { jnxoptIfODUk 1 } 
+
+
+jnxoptIfODUkConfigEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfODUkConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains ODUk configuration
+      information of an interface." 
+    INDEX { ifIndex } 
+    ::= { jnxoptIfODUkConfigTable 1 } 
+
+
+JnxoptIfODUkConfigEntry ::=
+    SEQUENCE { 
+       jnxoptIfODUkDirectionality              JnxoptIfDirectionality,
+       jnxoptIfODUkBitRateK                    JnxoptIfBitRateK,
+       jnxoptIfODUkTcmFieldsInUse              BITS,
+       jnxoptIfODUkPositionSeqCurrentSize      Unsigned32,
+       jnxoptIfODUkTtpPresent                  TruthValue 
+    } 
+
+
+jnxoptIfODUkDirectionality OBJECT-TYPE 
+    SYNTAX JnxoptIfDirectionality 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the directionality of the entity." 
+    ::= { jnxoptIfODUkConfigEntry 1 } 
+ 
+
+jnxoptIfODUkBitRateK OBJECT-TYPE 
+    SYNTAX JnxoptIfBitRateK 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the bit rate of the entity." 
+    ::= { jnxoptIfODUkConfigEntry 2 } 
+
+
+jnxoptIfODUkTcmFieldsInUse OBJECT-TYPE 
+    SYNTAX BITS { 
+        tcmField1(0),
+        tcmField2(1),
+        tcmField3(2),
+        tcmField4(3),
+        tcmField5(4),
+        tcmField6(5)
+    } 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the TCM field(s) that are currently in use. 
+      The positions of the bits correspond to the TCM fields. 
+      A bit that is set to 1 means that the corresponding TCM 
+      field is used. This object will be updated when rows are 
+      created in or deleted from the jnxoptIfODUkTConfigTable, or 
+      the jnxoptIfODUkTNimConfigTable." 
+    ::= { jnxoptIfODUkConfigEntry 3 } 
+
+
+jnxoptIfODUkPositionSeqCurrentSize OBJECT-TYPE 
+    SYNTAX Unsigned32 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "This variable indicates the current size of the position 
+      sequence (i.e., number of TCM function and/or GCC12 
+      access that have been created in the ODUk interface). 
+      When the value of this variable is greater than zero, 
+      it means that one or more TCM function and/or GCC12 
+      access have been created in the ODUk interface. In this 
+      case, there will be as many rows in the 
+      jnxoptIfODUkPositionSeqTable as the value of 
+      jnxoptIfODUkPositionSeqCurrentSize corresponding to this 
+      ODUk interface, one row for each TCM function or GCC12 
+      access. The position of the TCM function and/or 
+      GCC12 access within the sequence is indicated by the 
+      jnxoptIfODUkPositionSeqPosition variable in 
+      jnxoptIfODUkPositionSeqTable. 
+      The jnxoptIfODUkPositionSeqTable also provides pointers 
+      to the corresponding TCM function (jnxoptIfODUkT) and 
+      GCC12 access (jnxoptIfGCC12) entities."
+    ::= { jnxoptIfODUkConfigEntry 4 } 
+
+
+jnxoptIfODUkTtpPresent OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "This object has the value true(1) if the ifEntry under which 
+      it is instantiated contains an ODUk Trail Termination Point, 
+      i.e., is the endpoint of an ODUk path. In that case there 
+      will be a corresponding row in the ODUk TTP config table and 
+      it will not be possible to create corresponding rows in the 
+      ODUk NIM config table. This object has the value false(2) 
+      if the ifEntry under which it is instantiated contains an 
+      intermediate ODUk Connection Termination Point. In that case 
+      there is no corresponding row in the ODUk TTP config table, 
+      but it will be possible to create corresponding rows in the 
+      ODUk NIM config table. This object also affects the allowable 
+      options in rows created in the GCC12 config table and in the 
+      ODUkT config table, as specified in the DESCRIPTION clauses 
+      of the columns in those tables." 
+    ::= { jnxoptIfODUkConfigEntry 5 } 
+
+
+-- ODUk Trail Termination Point (TTP) config table 
+
+
+jnxoptIfODUkTtpConfigTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfODUkTtpConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A table of ODUk TTP configuration information." 
+    ::= { jnxoptIfODUk 2 } 
+ 
+
+jnxoptIfODUkTtpConfigEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfODUkTtpConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A conceptual row that contains ODUk TTP configuration
+      information of an interface." 
+    INDEX { ifIndex } 
+    ::= { jnxoptIfODUkTtpConfigTable 1 } 
+
+
+JnxoptIfODUkTtpConfigEntry ::=
+    SEQUENCE { 
+        jnxoptIfODUkTtpTraceIdentifierTransmitted  JnxoptIfTxTI,
+        jnxoptIfODUkTtpDAPIExpected                JnxoptIfExDAPI,
+        jnxoptIfODUkTtpSAPIExpected                JnxoptIfExSAPI,
+        jnxoptIfODUkTtpTraceIdentifierAccepted     JnxoptIfAcTI,
+        jnxoptIfODUkTtpTIMDetMode                  JnxoptIfTIMDetMode,
+        jnxoptIfODUkTtpTIMActEnabled               TruthValue,
+        jnxoptIfODUkTtpDEGThr                      JnxoptIfDEGThr,
+        jnxoptIfODUkTtpDEGM                        JnxoptIfDEGM,
+        jnxoptIfODUkTtpCurrentStatus               BITS
+    } 
+ 
+
+jnxoptIfODUkTtpTraceIdentifierTransmitted OBJECT-TYPE 
+    SYNTAX JnxoptIfTxTI 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The trace identifier transmitted. 
+      This object is applicable when jnxoptIfODUkDirectionality 
+      has the value source(2) or bidirectional(3). It must not 
+      be instantiated in rows where jnxoptIfODUkDirectionality 
+      has the value sink(1). 
+      If no value is ever set by a management entity for this 
+      object, system-specific default value will be used. 
+      Any implementation that instantiates this object must 
+      document the system-specific default value or how it 
+      is derived."
+   ::= { jnxoptIfODUkTtpConfigEntry 1 } 
+
+
+jnxoptIfODUkTtpDAPIExpected OBJECT-TYPE 
+    SYNTAX JnxoptIfExDAPI 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The DAPI expected by the receiver. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfODUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfODUkDirectionality has the value source(2). 
+      This object has no effect when jnxoptIfODUkTtpTIMDetMode has 
+      the value off(1)."
+    ::= { jnxoptIfODUkTtpConfigEntry 2 } 
+
+
+
+jnxoptIfODUkTtpSAPIExpected OBJECT-TYPE 
+    SYNTAX JnxoptIfExSAPI 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "The SAPI expected by the receiver. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfODUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfODUkDirectionality has the value source(2). 
+      This object has no effect when jnxoptIfODUkTtpTIMDetMode has 
+      the value off(1)."
+    ::= { jnxoptIfODUkTtpConfigEntry 3 } 
+
+
+jnxoptIfODUkTtpTraceIdentifierAccepted OBJECT-TYPE 
+    SYNTAX JnxoptIfAcTI 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The actual trace identifier accepted. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfODUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfODUkDirectionality has the value source(2). 
+      The value of this object is unspecified when 
+      jnxoptIfODUkTtpCurrentStatus indicates a near-end defect 
+      (i.e., oci(0), lck(1), ssf(5)) that prevents extraction 
+      of the trace message."
+    ::= { jnxoptIfODUkTtpConfigEntry 4 } 
+
+
+jnxoptIfODUkTtpTIMDetMode OBJECT-TYPE 
+    SYNTAX JnxoptIfTIMDetMode 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the mode of the Trace Identifier Mismatch (TIM) 
+      Detection function. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfODUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfODUkDirectionality has the value source(2). 
+      The default value of this object is off(1)."
+    ::= { jnxoptIfODUkTtpConfigEntry 5 } 
+
+
+jnxoptIfODUkTtpTIMActEnabled OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "Indicates whether the Trace Identifier Mismatch (TIM) 
+      Consequent Action function is enabled. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfODUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfODUkDirectionality has the value source(2). 
+      This object has no effect when jnxoptIfODUkTtpTIMDetMode has 
+      the value off(1). 
+      The default value of this object is false(2)."
+    ::= { jnxoptIfODUkTtpConfigEntry 6 } 
+
+
+jnxoptIfODUkTtpDEGThr OBJECT-TYPE 
+    SYNTAX JnxoptIfDEGThr 
+    UNITS "percentage" 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the threshold level for declaring a performance 
+      monitoring (PM) Second to be bad. A PM Second is declared bad if 
+      the percentage of detected errored blocks in that second is 
+      greater than or equal to jnxoptIfODUkDEGThr. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfODUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfODUkDirectionality has the value source(2). 
+      The default value of this object is Severely Errored Second 
+      (SES) Estimator (See ITU-T G.7710)."
+    ::= { jnxoptIfODUkTtpConfigEntry 7 } 
+
+
+jnxoptIfODUkTtpDEGM OBJECT-TYPE 
+    SYNTAX JnxoptIfDEGM 
+    MAX-ACCESS read-write 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the threshold level for declaring a Degraded Signal 
+      defect (dDEG). A dDEG shall be declared if jnxoptIfODUkDEGM 
+      consecutive bad PM Seconds are detected. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfODUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfODUkDirectionality has the value source(2). 
+      The default value of this object is 7 (See ITU-T G.7710)."
+    ::= { jnxoptIfODUkTtpConfigEntry 8 } 
+
+
+jnxoptIfODUkTtpCurrentStatus OBJECT-TYPE 
+    SYNTAX BITS { 
+        oci(0),
+        lck(1),
+        tim(2),
+        deg(3),
+        bdi(4),
+        ssf(5)
+    }
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the defect condition of the entity, if any. 
+      This object is only applicable to the sink function, i.e., 
+      only when jnxoptIfODUkDirectionality has the value sink(1) 
+      or bidirectional(3). It must not be instantiated in rows 
+      where jnxoptIfODUkDirectionality has the value source(2)."
+    ::= { jnxoptIfODUkTtpConfigEntry 9 } 
+
+
+-- ODUk Position Sequence table 
+
+
+jnxoptIfODUkPositionSeqTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfODUkPositionSeqEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A table of ODUk Position Sequence information." 
+    ::= { jnxoptIfODUk 3 } 
+
+
+jnxoptIfODUkPositionSeqEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfODUkPositionSeqEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A conceptual row that contains ODUk position sequence 
+      information of an ODUk interface. The ODUk interface 
+      is identified by the ifIndex. Associated with each 
+      ODUk interface there may be one of more conceptual 
+      rows in the jnxoptIfODUkPositionSeqTable. Each row 
+      represents a TCM or GCC12 access function within the 
+      associated ODUk interface. Rows of the 
+      jnxoptIfODUkPositionSeqTable table are created/deleted 
+      as the result of the creation/deletion of the jnxoptIfODUkT 
+      or jnxoptIfGCC12 entities." 
+    INDEX { ifIndex, jnxoptIfODUkPositionSeqIndex } 
+    ::= { jnxoptIfODUkPositionSeqTable 1 } 
+
+
+JnxoptIfODUkPositionSeqEntry ::= 
+    SEQUENCE { 
+        jnxoptIfODUkPositionSeqIndex            Unsigned32,
+        jnxoptIfODUkPositionSeqPosition         Unsigned32,
+        jnxoptIfODUkPositionSeqPointer          RowPointer 
+    } 
+
+
+jnxoptIfODUkPositionSeqIndex OBJECT-TYPE 
+    SYNTAX Unsigned32 (1..4294967295) 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "This variable identifies a row in the 
+      jnxoptIfODUkPositionSeqTable Table. 
+      Each row of the jnxoptIfODUkPositionSeqTable Table 
+      represents a TCM or GCC12 access function within the 
+      associated ODUk interface."
+    ::= { jnxoptIfODUkPositionSeqEntry 1 } 
+
+
+jnxoptIfODUkPositionSeqPosition OBJECT-TYPE 
+    SYNTAX Unsigned32 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "This variable indicates the position of the TCM or 
+      GCC12 access function within the sequence of TCMs & 
+      GCC12 access functions of the associated ODUk 
+      interface. The TCM or GCC12 presented by this row is 
+      referenced by the jnxoptIfODUkPositionSeqPointer variable."
+    ::= { jnxoptIfODUkPositionSeqEntry 2 } 
+
+
+jnxoptIfODUkPositionSeqPointer OBJECT-TYPE 
+    SYNTAX RowPointer 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "This variable identifies the TCM or GCC12 access function 
+      by pointing to the corresponding jnxoptIfODUkT or jnxoptIfGCC12 
+      entity."
+    ::= { jnxoptIfODUkPositionSeqEntry 3 } 
+
+
+-- ODUk Non-intrusive monitoring (Nim) config table 
+
+
+jnxoptIfODUkNimConfigTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfODUkNimConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of ODUkNim configuration information." 
+    ::= { jnxoptIfODUk 4 } 
+
+
+jnxoptIfODUkNimConfigEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfODUkNimConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains ODUkNim configuration 
+      information of an interface. Each instance must 
+      correspond to an instance of jnxoptIfODUkConfigEntry 
+      for which jnxoptIfODUkTtpPresent has the value false(2).
+      Instances of this conceptual row persist across 
+      agent restarts, and read-create columns other 
+      than the status column may be modified while the 
+      row is active."
+    INDEX { ifIndex, jnxoptIfODUkNimDirectionality }
+    ::= { jnxoptIfODUkNimConfigTable 1 } 
+
+
+JnxoptIfODUkNimConfigEntry ::= 
+    SEQUENCE { 
+        jnxoptIfODUkNimDirectionality              JnxoptIfSinkOrSource,
+        jnxoptIfODUkNimDAPIExpected                JnxoptIfExDAPI,
+        jnxoptIfODUkNimSAPIExpected                JnxoptIfExSAPI,
+        jnxoptIfODUkNimTraceIdentifierAccepted     JnxoptIfAcTI,
+        jnxoptIfODUkNimTIMDetMode                  JnxoptIfTIMDetMode,
+        jnxoptIfODUkNimTIMActEnabled               TruthValue,
+        jnxoptIfODUkNimDEGThr                      JnxoptIfDEGThr,
+        jnxoptIfODUkNimDEGM                        JnxoptIfDEGM,
+        jnxoptIfODUkNimCurrentStatus               BITS,
+        jnxoptIfODUkNimRowStatus                   RowStatus 
+    } 
+
+
+jnxoptIfODUkNimDirectionality OBJECT-TYPE 
+    SYNTAX JnxoptIfSinkOrSource 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "Specifies the monitor point for the ODUk Path non-intrusive 
+      monitoring function. The value source(2) is not allowed 
+      if the corresponding instance of jnxoptIfODUkDirectionality 
+      has the value sink(1), and the value sink(1) is not allowed 
+      if the corresponding instance of jnxoptIfODUkDirectionality 
+      has the value source(2). Either the value sink(1) or 
+      source(2) is allowed if the corresponding instance of 
+      jnxoptIfODUkDirectionality has the value bidirectional(3).
+      The value sink(1) means monitoring at the sink direction 
+      path signal of the ODUk CTP.
+      The value source(2) means monitoring at the source direction 
+      path signal of the ODUk CTP. Monitoring the source direction 
+      of an ODUk CTP is necessary in those cases where the ODUk CTP 
+      is at an SNCP (Subnetwork Connection Protection) end (e.g., see 
+      Figure I.1.2/G.874.1). If one would like to get the performance 
+      of the protected connection, one cannot use the NIM function 
+      at both ODUk CTP sinks (before the matrix), instead one should 
+      monitor the signal at the source ODUk CTP after the matrix."
+    ::= { jnxoptIfODUkNimConfigEntry 1 } 
+
+
+jnxoptIfODUkNimDAPIExpected OBJECT-TYPE 
+    SYNTAX JnxoptIfExDAPI 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "The DAPI expected by the receiver. 
+      This object has no effect if jnxoptIfODUkNimTIMDetMode has 
+      the value off(1) or sapi(3)."
+    ::= { jnxoptIfODUkNimConfigEntry 2 } 
+
+
+jnxoptIfODUkNimSAPIExpected OBJECT-TYPE 
+    SYNTAX JnxoptIfExSAPI 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "The SAPI expected by the receiver. 
+      This object has no effect if jnxoptIfODUkNimTIMDetMode has 
+      the value off(1) or dapi(2)."
+    ::= { jnxoptIfODUkNimConfigEntry 3 } 
+
+
+jnxoptIfODUkNimTraceIdentifierAccepted OBJECT-TYPE 
+    SYNTAX JnxoptIfAcTI 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The actual trace identifier accepted. The value of 
+      this object is unspecified if jnxoptIfODUkNimCurrentStatus 
+      has any of the bit positions oci(0), lck(1), or ssf(5) 
+      set or if jnxoptIfODUkNimRowStatus has any value other 
+      than active(1)."
+    ::= { jnxoptIfODUkNimConfigEntry 4 } 
+
+
+jnxoptIfODUkNimTIMDetMode OBJECT-TYPE 
+    SYNTAX JnxoptIfTIMDetMode 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the mode of the Trace Identifier Mismatch (TIM) 
+      Detection function." 
+    ::= { jnxoptIfODUkNimConfigEntry 5 } 
+
+
+jnxoptIfODUkNimTIMActEnabled OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates whether the Trace Identifier Mismatch (TIM) 
+      Consequent Action function is enabled." 
+    ::= { jnxoptIfODUkNimConfigEntry 6 } 
+
+
+jnxoptIfODUkNimDEGThr OBJECT-TYPE 
+    SYNTAX JnxoptIfDEGThr 
+    UNITS "percentage" 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the threshold level for declaring a performance 
+      monitoring (PM) Second to be bad. A PM Second is declared bad 
+      if the percentage of detected errored blocks in that second is 
+      greater than or equal to jnxoptIfODUkNimDEGThr." 
+    ::= { jnxoptIfODUkNimConfigEntry 7 } 
+
+
+jnxoptIfODUkNimDEGM OBJECT-TYPE 
+    SYNTAX JnxoptIfDEGM 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the threshold level for declaring a Degraded Signal 
+      defect (dDEG). A dDEG shall be declared if jnxoptIfODUkNimDEGM 
+      consecutive bad PM Seconds are detected." 
+    ::= { jnxoptIfODUkNimConfigEntry 8 } 
+
+
+jnxoptIfODUkNimCurrentStatus OBJECT-TYPE 
+    SYNTAX BITS { 
+        oci(0), 
+        lck(1), 
+        tim(2), 
+        deg(3), 
+        bdi(4), 
+        ssf(5) 
+    } 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the defect condition of the entity, if 
+      any. The value of this object is unspecified if 
+      jnxoptIfODUkNimRowStatus has any value other than 
+      active(1)." 
+    ::= { jnxoptIfODUkNimConfigEntry 9 } 
+
+
+jnxoptIfODUkNimRowStatus OBJECT-TYPE 
+    SYNTAX RowStatus 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "This columnar object is used for creating and deleting 
+      a conceptual row of the jnxoptIfODUkNim config table. 
+      It is used to model the activateNim and deactivateNim 
+      operations of an OTUk_CTP for non-intrusive monitoring 
+      control as defined in G.874.1. Setting RowStatus to 
+      createAndGo or createAndWait implies activateNim. 
+      Setting RowStatus to destroy implies deactivateNim."
+    ::= { jnxoptIfODUkNimConfigEntry 10 } 
+
+
+-- GCC12 config table 
+
+
+jnxoptIfGCC12ConfigTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfGCC12ConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of GCC12 configuration information. 
+      The GCC function processes the GCC overhead bytes passing 
+      through them but leave the remainder of the ODUk overhead 
+      and payload data alone."
+    ::= { jnxoptIfODUk 5 } 
+
+
+jnxoptIfGCC12ConfigEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfGCC12ConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains GCC12 configuration 
+      information of an interface. Each instance must 
+      correspond to an instance of jnxoptIfODUkConfigEntry. 
+      Separate instances providing GCC1-only access and 
+      GCC2-only access may exist for a given ifIndex value, 
+      or a single instance providing GCC1 + GCC2 may exist, 
+      but a GCC1 + GCC2 instance may not coexist with a 
+      GCC1-only or GCC2-only instance.
+      Instances of this conceptual row persist across agent
+      restarts." 
+    INDEX { ifIndex, jnxoptIfGCC12Codirectional, jnxoptIfGCC12GCCAccess } 
+    ::= { jnxoptIfGCC12ConfigTable 1 } 
+
+
+JnxoptIfGCC12ConfigEntry ::= 
+    SEQUENCE { 
+        jnxoptIfGCC12Codirectional      TruthValue,
+        jnxoptIfGCC12GCCAccess          INTEGER,
+        jnxoptIfGCC12GCCPassThrough     TruthValue,
+        jnxoptIfGCC12Application        SnmpAdminString,
+        jnxoptIfGCC12RowStatus          RowStatus
+    } 
+
+
+jnxoptIfGCC12Codirectional OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the directionality of the GCC12 termination with 
+      respect to the associated ODUk CTP. The value true(1) means 
+      that the sink part of the GCC12 extracts COMMS data from the 
+      signal at the input to the ODUk CTP sink and the source part 
+      of the GCC12 inserts COMMS data into the signal at the output 
+      of the ODUk CTP source. The value false(2) means that the 
+      sink part of the GCC12 extracts COMMS data from the signal at 
+      the output of the ODUk CTP source and the source part of the 
+      GCC12 inserts COMMS data into the signal at the input of the 
+      ODUk CTP sink. This attribute may assume either value when 
+      the corresponding instance of jnxoptIfODUkTtpPresent has the 
+      value false(2). When the value of the corresponding instance 
+      of jnxoptIfODUkTtpPresent is true(1) then the only value allowed 
+      for this attribute is true(1)." 
+    ::= { jnxoptIfGCC12ConfigEntry 1 } 
+
+
+jnxoptIfGCC12GCCAccess OBJECT-TYPE 
+    SYNTAX INTEGER { 
+        gcc1 (1), 
+        gcc2 (2), 
+        gcc1and2 (3) 
+    } 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the GCC access represented by the entity." 
+    ::= { jnxoptIfGCC12ConfigEntry 2 } 
+
+
+jnxoptIfGCC12GCCPassThrough OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION 
+      "Controls whether the selected GCC overhead bytes are passed 
+      through or modified. The value true(1) means that the selected 
+      GCC overhead bytes are passed through unmodified from the ODUk 
+      CTP input to the ODUk CTP output. The value false(2) means that 
+      the selected GCC overhead bytes are set to zero at the ODUk CTP 
+      output after the extraction of the COMMS data. This object has 
+      no effect if the corresponding instance of jnxoptIfODUkTtpPresent 
+      has the value true(1).
+      The value of this object may not be changed when 
+      jnxoptIfGCC12RowStatus has the value active(1)." 
+    ::= { jnxoptIfGCC12ConfigEntry 3 } 
+
+
+jnxoptIfGCC12Application OBJECT-TYPE 
+    SYNTAX SnmpAdminString 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the application transported by the GCC12 entity. 
+      Example applications are ECC, User data channel.
+      The value of this object may not be changed when 
+      jnxoptIfGCC12RowStatus has the value active(1)." 
+    ::= { jnxoptIfGCC12ConfigEntry 4 } 
+
+
+jnxoptIfGCC12RowStatus OBJECT-TYPE 
+    SYNTAX RowStatus 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION 
+      "This columnar object is used for creating and deleting 
+      a conceptual row of the jnxoptIfGCC12 config table. It is 
+      used to model the addGCC12Access and removeGCC12Access 
+      operations of an ODUk_CTP or ODUk_TTP for GCC12 access 
+      control as defined in G.874.1. Setting RowStatus to 
+      createAndGo or createAndWait implies addGCC12Access. 
+      Setting RowStatus to destroy implies removeGCC12Access. 
+      Successful addition/removal of the GCC12 access function 
+      will result in updating the 
+      jnxoptIfODUkPositionSeqCurrentSize variable and the 
+      jnxoptIfODUkPositionSeqTable table of the associated 
+      ODUk entry in the jnxoptIfODUkConfigTable." 
+    ::= { jnxoptIfGCC12ConfigEntry 5 } 
+
+
+-- the jnxoptIfODUkT group 
+-- This group handles the configuration information 
+-- for the ODUkT layers. 
+
+
+-- ODUkT config table 
+
+
+jnxoptIfODUkTConfigTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfODUkTConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A table of ODUkT configuration information." 
+    ::= { jnxoptIfODUkT 1 } 
+
+
+jnxoptIfODUkTConfigEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfODUkTConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "A conceptual row that contains ODUkT configuration 
+      information of an interface. Each instance must 
+      correspond to an instance of jnxoptIfODUkConfigEntry. 
+      Rows in this table are mutually exclusive with rows 
+      in the ODUkT NIM config table -- in other words, this 
+      row object may not be instantiated for a given pair 
+      of ifIndex and TCM field values if a corresponding 
+      instance of jnxoptIfODUkTNimConfigEntry already exists.
+      Instances of this conceptual row persist across agent 
+      restarts. Except where noted otherwise, read-create 
+      columns other than the status column may be modified 
+      while the row is active."
+    INDEX { ifIndex, jnxoptIfODUkTTcmField, jnxoptIfODUkTCodirectional }
+    ::= { jnxoptIfODUkTConfigTable 1 } 
+
+JnxoptIfODUkTConfigEntry ::= 
+    SEQUENCE { 
+        jnxoptIfODUkTTcmField                    Unsigned32,
+        jnxoptIfODUkTCodirectional               TruthValue,
+        jnxoptIfODUkTTraceIdentifierTransmitted  JnxoptIfTxTI,
+        jnxoptIfODUkTDAPIExpected                JnxoptIfExDAPI,
+        jnxoptIfODUkTSAPIExpected                JnxoptIfExSAPI,
+        jnxoptIfODUkTTraceIdentifierAccepted     JnxoptIfAcTI,
+        jnxoptIfODUkTTIMDetMode                  JnxoptIfTIMDetMode,
+        jnxoptIfODUkTTIMActEnabled               TruthValue,
+        jnxoptIfODUkTDEGThr                      JnxoptIfDEGThr,
+        jnxoptIfODUkTDEGM                        JnxoptIfDEGM,
+        jnxoptIfODUkTSinkMode                    INTEGER,
+        jnxoptIfODUkTSinkLockSignalAdminState    INTEGER,
+        jnxoptIfODUkTSourceLockSignalAdminState  INTEGER,
+        jnxoptIfODUkTCurrentStatus               BITS,
+        jnxoptIfODUkTRowStatus                   RowStatus 
+    } 
+
+
+jnxoptIfODUkTTcmField OBJECT-TYPE 
+    SYNTAX Unsigned32 (1..6) 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the tandem connection monitoring 
+      field of the ODUk OH. Valid values are 
+      integers from 1 to 6." 
+    ::= { jnxoptIfODUkTConfigEntry 1 } 
+
+
+jnxoptIfODUkTCodirectional OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the directionality of the ODUkT termination point with 
+      respect to the associated ODUk CTP. The value true(1) means 
+      that the sink part of the ODUkT TP extracts TCM data from the 
+      signal at the input to the ODUk CTP sink and the source part 
+      of the ODUkT TP inserts TCM data into the signal at the output 
+      of the ODUk CTP source. The value false(2) means that the 
+      sink part of the ODUkT TP extracts TCM data from the signal at 
+      the output of the ODUk CTP source and the source part of the 
+      ODUkT TP inserts TCM data into the signal at the input of the 
+      ODUk CTP sink. This attribute may assume either value when 
+      the corresponding instance of jnxoptIfODUkTtpPresent has the 
+      value false(2). When the value of the corresponding instance 
+      of jnxoptIfODUkTtpPresent is true(1) then the only value allowed 
+      for this attribute is true(1)." 
+    ::= { jnxoptIfODUkTConfigEntry 2 } 
+
+
+jnxoptIfODUkTTraceIdentifierTransmitted OBJECT-TYPE 
+    SYNTAX JnxoptIfTxTI 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION 
+      "The trace identifier transmitted. 
+      This object is applicable only to the following three cases.
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value false(2), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value true(1). 
+      It must not be instantiated in rows for all other cases." 
+    ::= { jnxoptIfODUkTConfigEntry 3 } 
+
+
+jnxoptIfODUkTDAPIExpected OBJECT-TYPE 
+    SYNTAX JnxoptIfExDAPI 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "The DAPI expected by the receiver. 
+      This object is applicable only to the following three cases.
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value true(1), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value false(2). 
+      It must not be instantiated in rows for all other cases. 
+      This object has no effect when jnxoptIfODUkTTIMDetMode has 
+      the value off(1)."
+    ::= { jnxoptIfODUkTConfigEntry 4 } 
+
+
+jnxoptIfODUkTSAPIExpected OBJECT-TYPE 
+    SYNTAX JnxoptIfExSAPI 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "The SAPI expected by the receiver. 
+      This object is applicable only to the following three cases.
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value true(1), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value false(2). 
+      It must not be instantiated in rows for all other cases. 
+      This object has no effect when jnxoptIfODUkTTIMDetMode has 
+      the value off(1)."
+    ::= { jnxoptIfODUkTConfigEntry 5 } 
+
+
+jnxoptIfODUkTTraceIdentifierAccepted OBJECT-TYPE 
+    SYNTAX JnxoptIfAcTI 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "The actual trace identifier accepted. 
+      This object is applicable only to the following three cases.
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value true(1), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value false(2). 
+      It must not be instantiated in rows for all other cases. 
+      The value of this object is unspecified when 
+      jnxoptIfODUkTCurrentStatus indicates a near-end defect 
+      (i.e., oci(0), lck(1), ssf(5)) that prevents extraction 
+      of the trace message." 
+    ::= { jnxoptIfODUkTConfigEntry 6 } 
+
+
+jnxoptIfODUkTTIMDetMode OBJECT-TYPE 
+    SYNTAX JnxoptIfTIMDetMode 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the mode of the Trace Identifier Mismatch (TIM) 
+      Detection function. 
+      This object is applicable only to the following three cases.
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value true(1), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value false(2). 
+      It must not be instantiated in rows for all other cases. 
+      The default value of this object is off(1)."
+    ::= { jnxoptIfODUkTConfigEntry 7 } 
+
+
+jnxoptIfODUkTTIMActEnabled OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "Indicates whether the Trace Identifier Mismatch (TIM) 
+      Consequent Action function is enabled. 
+      This object is applicable only to the following three cases.
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value true(1), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value false(2). 
+      It must not be instantiated in rows for all other cases. 
+      This object has no effect when jnxoptIfODUkTTIMDetMode has 
+      the value off(1). 
+      The default value of this object is false(2)."
+    ::= { jnxoptIfODUkTConfigEntry 8 } 
+
+
+jnxoptIfODUkTDEGThr OBJECT-TYPE 
+    SYNTAX JnxoptIfDEGThr 
+    UNITS "percentage" 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the threshold level for declaring a performance 
+      monitoring (PM) Second to be bad. A PM Second is declared bad if 
+      the percentage of detected errored blocks in that second is 
+      greater than or equal to jnxoptIfODUkTDEGThr. 
+      This object is applicable only to the following three cases.
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value true(1), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value false(2). 
+      It must not be instantiated in rows for all other cases. 
+      The default value of this object is Severely Errored Second 
+      (SES) Estimator (See ITU-T G.7710)."
+    ::= { jnxoptIfODUkTConfigEntry 9 } 
+
+
+jnxoptIfODUkTDEGM OBJECT-TYPE 
+    SYNTAX JnxoptIfDEGM 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the threshold level for declaring a Degraded Signal 
+      defect (dDEG). A dDEG shall be declared if jnxoptIfODUkTDEGM 
+      consecutive bad PM Seconds are detected. 
+      This object is applicable only to the following three cases.
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value true(1), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value false(2). 
+      It must not be instantiated in rows for all other cases. 
+      The default value of this object is 7 (See ITU-T G.7710)."
+    ::= { jnxoptIfODUkTConfigEntry 10 } 
+
+
+jnxoptIfODUkTSinkMode OBJECT-TYPE
+    SYNTAX INTEGER { 
+        operational (1), 
+        monitor (2) 
+    }
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "This variable specifies the TCM mode at the entity. 
+      The value operational(1) means that TCM Overhead (TCMOH) 
+      processes (see ITU-T G.798) shall be 
+      performed and consequent actions for AIS, Trail 
+      Signal Fail (TSF), Trail Signal Degraded (TSD) shall be 
+      initiated in case of defects. 
+      The value monitor(2) means that TCMOH processes shall be 
+      performed but consequent actions for AIS, Trail 
+      Server Failure (TSF), Trail Server Degraded (TSD) shall _not_ be 
+      initiated in case of defects. 
+      This object is applicable only when the value of 
+      jnxoptIfODUkTtpPresent is false(2) and also either one of the 
+      following three cases holds:
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value true(1), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value false(2). 
+      It must not be instantiated in rows for all other cases." 
+    ::= { jnxoptIfODUkTConfigEntry 11 } 
+
+
+jnxoptIfODUkTSinkLockSignalAdminState OBJECT-TYPE 
+    SYNTAX INTEGER { 
+        locked(1), 
+        normal(2) 
+    } 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION 
+      "Provides the capability to provision the LOCK signal, which 
+      is one of the ODUk maintenance signals, at the ODUKT sink. When 
+      a Tandem Connection endpoint is set to admin state locked, 
+      it inserts the ODUk-LCK signal in the sink direction.
+      This object is applicable only when the value of 
+      jnxoptIfODUkTtpPresent is false(2) and also either one of the 
+      following three cases holds:
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value true(1), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value false(2). 
+      It must not be instantiated in rows for all other cases." 
+    ::= { jnxoptIfODUkTConfigEntry 12 } 
+
+
+jnxoptIfODUkTSourceLockSignalAdminState OBJECT-TYPE 
+    SYNTAX INTEGER { 
+        locked(1), 
+        normal(2) 
+    } 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION 
+      "Provides the capability to provision the LOCK signal, which 
+      is one of the ODUk maintenance signals, at the source. 
+      When a Tandem Connection endpoint is set to admin state 
+      locked, it inserts the ODUk-LCK signal in the source 
+      direction. 
+      This object is applicable only when either one of the 
+      following three cases holds:
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value false(2), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value true(1). 
+      It must not be instantiated in rows for all other cases." 
+    ::= { jnxoptIfODUkTConfigEntry 13 } 
+
+
+jnxoptIfODUkTCurrentStatus OBJECT-TYPE
+    SYNTAX BITS { 
+        oci(0), 
+        lck(1), 
+        tim(2), 
+        deg(3), 
+        bdi(4), 
+        ssf(5) 
+    }
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the defect condition of the entity, if any. 
+      This object is applicable only when either one of the 
+      following three cases holds:
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value true(1), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value false(2). 
+      It must not be instantiated in rows for all other cases." 
+    ::= { jnxoptIfODUkTConfigEntry 14 } 
+
+
+jnxoptIfODUkTRowStatus OBJECT-TYPE 
+    SYNTAX RowStatus 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "This columnar object is used for creating and deleting a 
+      conceptual row of the jnxoptIfODUkT config table. 
+      It is used to model the addTCM and removeTCM operations of an 
+      ODUk_CTP or ODUk_TTP for Tandem connection monitoring as defined 
+      in ITU-T G.874.1. 
+      Setting RowStatus to createAndGo or createAndWait implies addTCM. 
+      Setting RowStatus to destroy implies removeTCM. 
+      Successful addition/removal of TCM will result in updating the 
+      jnxoptIfODUkTcmFieldsInUse and jnxoptIfODUkPositionSeqCurrentSize 
+      variables and the jnxoptIfODUkPositionSeqTable table of the 
+      associated ODUk entry in the jnxoptIfODUkConfigTable." 
+    ::= { jnxoptIfODUkTConfigEntry 15 } 
+
+
+-- ODUkT Non-intrusive monitoring (Nim) config table 
+
+
+jnxoptIfODUkTNimConfigTable OBJECT-TYPE 
+    SYNTAX SEQUENCE OF JnxoptIfODUkTNimConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A table of ODUkTNim configuration information." 
+    ::= { jnxoptIfODUkT 2 } 
+
+
+jnxoptIfODUkTNimConfigEntry OBJECT-TYPE 
+    SYNTAX JnxoptIfODUkTNimConfigEntry 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION 
+      "A conceptual row that contains ODUkTNim configuration 
+      information of an interface. Each instance must 
+      correspond to an instance of jnxoptIfODUkConfigEntry. 
+      Rows in this table are mutually exclusive with rows 
+      in the ODUkT config table -- in other words, this 
+      row object may not be instantiated for a given pair 
+      of ifIndex and TCM field values if a corresponding 
+      instance of jnxoptIfODUkTConfigEntry already exists.
+      Instances of this conceptual row persist across 
+      agent restarts, and read-create columns other 
+      than the status column may be modified while the 
+      row is active."
+    INDEX {ifIndex, jnxoptIfODUkTNimTcmField, jnxoptIfODUkTNimDirectionality}
+    ::= { jnxoptIfODUkTNimConfigTable 1 } 
+
+JnxoptIfODUkTNimConfigEntry ::= 
+    SEQUENCE { 
+        jnxoptIfODUkTNimTcmField                    Unsigned32,
+        jnxoptIfODUkTNimDirectionality              JnxoptIfSinkOrSource,
+        jnxoptIfODUkTNimDAPIExpected                JnxoptIfExDAPI,
+        jnxoptIfODUkTNimSAPIExpected                JnxoptIfExSAPI,
+        jnxoptIfODUkTNimTraceIdentifierAccepted     JnxoptIfAcTI,
+        jnxoptIfODUkTNimTIMDetMode                  JnxoptIfTIMDetMode,
+        jnxoptIfODUkTNimTIMActEnabled               TruthValue,
+        jnxoptIfODUkTNimDEGThr                      JnxoptIfDEGThr,
+        jnxoptIfODUkTNimDEGM                        JnxoptIfDEGM,
+        jnxoptIfODUkTNimCurrentStatus               BITS,
+        jnxoptIfODUkTNimRowStatus                   RowStatus
+    } 
+
+
+jnxoptIfODUkTNimTcmField OBJECT-TYPE 
+    SYNTAX Unsigned32 (1..6) 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the tandem connection monitoring 
+      field of the ODUk OH on which non-intrusive monitoring 
+      is performed. Valid values are 
+      integers from 1 to 6."
+    ::= { jnxoptIfODUkTNimConfigEntry 1 } 
+
+
+jnxoptIfODUkTNimDirectionality OBJECT-TYPE 
+    SYNTAX JnxoptIfSinkOrSource 
+    MAX-ACCESS not-accessible 
+    STATUS current 
+    DESCRIPTION
+      "Specifies the monitor point for the ODUk TCM non-intrusive 
+      monitoring function. The value source(2) is not allowed 
+      if the corresponding instance of jnxoptIfODUkDirectionality 
+      has the value sink(1), and the value sink(1) is not allowed 
+      if the corresponding instance of jnxoptIfODUkDirectionality 
+      has the value source(2). Either the value sink(1) or 
+      source(2) is allowed if the corresponding instance of 
+      jnxoptIfODUkDirectionality has the value bidirectional(3). 
+      The value sink(1) means monitoring at the sink direction 
+      TCM signal of the ODUk CTP. 
+      The value source(2) means monitoring at the source direction 
+      path signal of the ODUk CTP."
+    ::= { jnxoptIfODUkTNimConfigEntry 2 } 
+
+
+jnxoptIfODUkTNimDAPIExpected OBJECT-TYPE 
+    SYNTAX JnxoptIfExDAPI 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "The DAPI expected by the receiver. 
+      This object has no effect if jnxoptIfODUkTNimTIMDetMode has 
+      the value off(1) or sapi(3)."
+    ::= { jnxoptIfODUkTNimConfigEntry 3 } 
+
+
+jnxoptIfODUkTNimSAPIExpected OBJECT-TYPE 
+    SYNTAX JnxoptIfExSAPI 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "The SAPI expected by the receiver. 
+      This object has no effect if jnxoptIfODUkTNimTIMDetMode has 
+      the value off(1) or dapi(2)." 
+    ::= { jnxoptIfODUkTNimConfigEntry 4 } 
+
+
+jnxoptIfODUkTNimTraceIdentifierAccepted OBJECT-TYPE 
+    SYNTAX JnxoptIfAcTI 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "The actual trace identifier accepted. The value of 
+      this object is unspecified if jnxoptIfODUkTNimCurrentStatus 
+      has any of the bit positions oci(0), lck(1), or ssf(5) 
+      set or if jnxoptIfODUkTNimRowStatus has any value other 
+      than active(1)." 
+    ::= { jnxoptIfODUkTNimConfigEntry 5 } 
+
+
+jnxoptIfODUkTNimTIMDetMode OBJECT-TYPE 
+    SYNTAX JnxoptIfTIMDetMode 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the mode of the Trace Identifier Mismatch (TIM) 
+      Detection function." 
+    ::= { jnxoptIfODUkTNimConfigEntry 6 } 
+
+
+jnxoptIfODUkTNimTIMActEnabled OBJECT-TYPE 
+    SYNTAX TruthValue 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates whether the Trace Identifier Mismatch (TIM) 
+      Consequent Action function is enabled." 
+    ::= { jnxoptIfODUkTNimConfigEntry 7 } 
+
+
+jnxoptIfODUkTNimDEGThr OBJECT-TYPE 
+    SYNTAX JnxoptIfDEGThr 
+    UNITS "percentage" 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the threshold level for declaring a performance 
+      monitoring (PM) Second to be bad. A PM Second is declared bad if 
+      the percentage of detected errored blocks in that second is 
+      greater than or equal to jnxoptIfODUkTNimDEGThr." 
+    ::= { jnxoptIfODUkTNimConfigEntry 8 } 
+
+
+jnxoptIfODUkTNimDEGM OBJECT-TYPE 
+    SYNTAX JnxoptIfDEGM 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION
+      "Indicates the threshold level for declaring a Degraded Signal 
+      defect (dDEG). A dDEG shall be declared if jnxoptIfODUkTNimDEGM 
+      consecutive bad PM Seconds are detected."
+    ::= { jnxoptIfODUkTNimConfigEntry 9 } 
+
+
+jnxoptIfODUkTNimCurrentStatus OBJECT-TYPE 
+    SYNTAX BITS { 
+        oci(0), 
+        lck(1), 
+        tim(2), 
+        deg(3), 
+        bdi(4), 
+        ssf(5) 
+    } 
+    MAX-ACCESS read-only 
+    STATUS current 
+    DESCRIPTION 
+      "Indicates the defect condition of the entity, if any. 
+      The value of this object is unspecified if 
+      jnxoptIfODUkTNimRowStatus has any value other than 
+      active(1)." 
+    ::= { jnxoptIfODUkTNimConfigEntry 10 } 
+
+
+jnxoptIfODUkTNimRowStatus OBJECT-TYPE 
+    SYNTAX RowStatus 
+    MAX-ACCESS read-create 
+    STATUS current 
+    DESCRIPTION 
+      "This columnar object is used for creating and deleting a 
+      conceptual row of the jnxoptIfODUkTNim config table. 
+      It is used to model the addTCM and removeTCM operations of an 
+      ODUk_CTP or ODUk_TTP for non-intrusive Tandem connection 
+      monitoring as defined in ITU-T G.874.1. 
+      Setting RowStatus to createAndGo or createAndWait implies addTCM. 
+      Setting RowStatus to destroy implies removeTCM. 
+      Successful addition/removal of Nim TCM will result in updating 
+      the jnxoptIfODUkPositionSeqCurrentSize variable and the 
+      jnxoptIfODUkPositionSeqTable table of the associated ODUk entry 
+      in the jnxoptIfODUkConfigTable." 
+    ::= { jnxoptIfODUkTNimConfigEntry 11 } 
+
+
+-- units of conformance 
+
+
+jnxoptIfOTMnGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOTMnOrder,
+        jnxoptIfOTMnReduced,
+        jnxoptIfOTMnBitRates,
+        jnxoptIfOTMnInterfaceType,
+        jnxoptIfOTMnTcmMax,
+         jnxoptIfOTMnOpticalReach
+    }
+    STATUS current 
+    DESCRIPTION 
+      "A collection of OTMn structure information objects." 
+    ::= { jnxoptIfGroups 1 } 
+
+
+jnxoptIfPerfMonGroup OBJECT-GROUP 
+    OBJECTS {     
+        jnxoptIfPerfMonCurrentTimeElapsed,
+        jnxoptIfPerfMonCurDayTimeElapsed,
+        jnxoptIfPerfMonIntervalNumIntervals,
+        jnxoptIfPerfMonIntervalNumInvalidIntervals
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of performance monitoring interval objects." 
+    ::= { jnxoptIfGroups 2 } 
+ 
+
+jnxoptIfOTSnCommonGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOTSnDirectionality 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of configuration objects 
+      applicable to all OTSn interfaces." 
+    ::= { jnxoptIfGroups 3 } 
+
+
+jnxoptIfOTSnSourceGroupFull OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOTSnTraceIdentifierTransmitted 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of configuration objects 
+       applicable to full-functionality/IaDI OTSn 
+       interfaces that support source functions." 
+    ::= { jnxoptIfGroups 4 } 
+
+
+jnxoptIfOTSnAPRStatusGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOTSnAprStatus 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of objects applicable to 
+      OTSn interfaces that support Automatic 
+      Power Reduction functions." 
+    ::= { jnxoptIfGroups 5 } 
+
+jnxoptIfOTSnAPRControlGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOTSnAprControl 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of objects applicable to 
+      OTSn interfaces that provide Automatic 
+      Power Reduction control functions." 
+    ::= { jnxoptIfGroups 6 } 
+ 
+jnxoptIfOTSnSinkGroupBasic OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOTSnCurrentStatus 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of configuration objects 
+      applicable to all OTSn interfaces that 
+      support sink functions." 
+    ::= { jnxoptIfGroups 7 } 
+
+jnxoptIfOTSnSinkGroupFull OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOTSnDAPIExpected, 
+        jnxoptIfOTSnSAPIExpected, 
+        jnxoptIfOTSnTraceIdentifierAccepted, 
+        jnxoptIfOTSnTIMDetMode, 
+        jnxoptIfOTSnTIMActEnabled 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of configuration objects 
+      applicable to full-functionality/IaDI OTSn 
+      interfaces that support sink functions." 
+    ::= { jnxoptIfGroups 8 } 
+   
+jnxoptIfOTSnSinkPreOtnPMGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOTSnSinkCurrentSuspectedFlag,
+        jnxoptIfOTSnSinkCurrentInputPower,
+        jnxoptIfOTSnSinkCurrentLowInputPower,
+        jnxoptIfOTSnSinkCurrentHighInputPower,
+        jnxoptIfOTSnSinkCurrentOutputPower,
+        jnxoptIfOTSnSinkCurrentLowOutputPower,
+        jnxoptIfOTSnSinkCurrentHighOutputPower,
+        jnxoptIfOTSnSinkIntervalSuspectedFlag,
+        jnxoptIfOTSnSinkIntervalLastInputPower,
+        jnxoptIfOTSnSinkIntervalLowInputPower,
+        jnxoptIfOTSnSinkIntervalHighInputPower,
+        jnxoptIfOTSnSinkIntervalLastOutputPower,
+        jnxoptIfOTSnSinkIntervalLowOutputPower,
+        jnxoptIfOTSnSinkIntervalHighOutputPower,
+        jnxoptIfOTSnSinkCurDaySuspectedFlag,
+        jnxoptIfOTSnSinkCurDayLowInputPower,
+        jnxoptIfOTSnSinkCurDayHighInputPower,
+        jnxoptIfOTSnSinkCurDayLowOutputPower,
+        jnxoptIfOTSnSinkCurDayHighOutputPower,
+        jnxoptIfOTSnSinkPrevDaySuspectedFlag,
+        jnxoptIfOTSnSinkPrevDayLastInputPower,
+        jnxoptIfOTSnSinkPrevDayLowInputPower,
+        jnxoptIfOTSnSinkPrevDayHighInputPower,
+        jnxoptIfOTSnSinkPrevDayLastOutputPower,
+        jnxoptIfOTSnSinkPrevDayLowOutputPower,
+        jnxoptIfOTSnSinkPrevDayHighOutputPower
+     }
+     STATUS current
+     DESCRIPTION
+       "A collection of pre-OTN performance monitoring 
+       objects applicable to OTSn interfaces that 
+       support sink functions."
+     ::= { jnxoptIfGroups 9 } 
+
+
+jnxoptIfOTSnSinkPreOtnPMThresholdGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOTSnSinkCurrentLowerInputPowerThreshold,
+        jnxoptIfOTSnSinkCurrentUpperInputPowerThreshold,
+        jnxoptIfOTSnSinkCurrentLowerOutputPowerThreshold,
+        jnxoptIfOTSnSinkCurrentUpperOutputPowerThreshold
+    }
+    STATUS current 
+    DESCRIPTION 
+      "A collection of pre-OTN performance monitoring 
+      threshold objects applicable to OTSn interfaces 
+      that support sink functions." 
+    ::= { jnxoptIfGroups 10 } 
+
+
+jnxoptIfOTSnSourcePreOtnPMGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOTSnSrcCurrentSuspectedFlag,
+        jnxoptIfOTSnSrcCurrentOutputPower,
+        jnxoptIfOTSnSrcCurrentLowOutputPower,
+        jnxoptIfOTSnSrcCurrentHighOutputPower,
+        jnxoptIfOTSnSrcCurrentInputPower,
+        jnxoptIfOTSnSrcCurrentLowInputPower,
+        jnxoptIfOTSnSrcCurrentHighInputPower,
+        jnxoptIfOTSnSrcIntervalSuspectedFlag,
+        jnxoptIfOTSnSrcIntervalLastOutputPower,
+        jnxoptIfOTSnSrcIntervalLowOutputPower,
+        jnxoptIfOTSnSrcIntervalHighOutputPower,
+        jnxoptIfOTSnSrcIntervalLastInputPower,
+        jnxoptIfOTSnSrcIntervalLowInputPower,
+        jnxoptIfOTSnSrcIntervalHighInputPower,
+        jnxoptIfOTSnSrcCurDaySuspectedFlag,
+        jnxoptIfOTSnSrcCurDayLowOutputPower,
+        jnxoptIfOTSnSrcCurDayHighOutputPower,
+        jnxoptIfOTSnSrcCurDayLowInputPower,
+        jnxoptIfOTSnSrcCurDayHighInputPower,
+        jnxoptIfOTSnSrcPrevDaySuspectedFlag,
+        jnxoptIfOTSnSrcPrevDayLastOutputPower,
+        jnxoptIfOTSnSrcPrevDayLowOutputPower,
+        jnxoptIfOTSnSrcPrevDayHighOutputPower,
+        jnxoptIfOTSnSrcPrevDayLastInputPower,
+        jnxoptIfOTSnSrcPrevDayLowInputPower,
+        jnxoptIfOTSnSrcPrevDayHighInputPower
+    }
+    STATUS current
+    DESCRIPTION
+      "A collection of pre-OTN performance monitoring 
+      objects applicable to OTSn interfaces that 
+      support source functions."
+    ::= { jnxoptIfGroups 11 } 
+
+
+jnxoptIfOTSnSourcePreOtnPMThresholdGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOTSnSrcCurrentLowerOutputPowerThreshold,
+        jnxoptIfOTSnSrcCurrentUpperOutputPowerThreshold,
+        jnxoptIfOTSnSrcCurrentLowerInputPowerThreshold,
+        jnxoptIfOTSnSrcCurrentUpperInputPowerThreshold
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of pre-OTN performance monitoring 
+      threshold objects applicable to OTSn interfaces 
+      that support source functions." 
+    ::= { jnxoptIfGroups 12 } 
+
+
+jnxoptIfOMSnCommonGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOMSnDirectionality 
+    }
+    STATUS current 
+    DESCRIPTION 
+      "A collection of configuration objects 
+      applicable to all OMSn interfaces." 
+    ::= { jnxoptIfGroups 13 } 
+
+
+jnxoptIfOMSnSinkGroupBasic OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOMSnCurrentStatus 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of configuration objects 
+      applicable to all OMSn interfaces that 
+      support sink functions." 
+    ::= { jnxoptIfGroups 14 } 
+
+
+jnxoptIfOMSnSinkPreOtnPMGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOMSnSinkCurrentSuspectedFlag,
+        jnxoptIfOMSnSinkCurrentAggregatedInputPower,
+        jnxoptIfOMSnSinkCurrentLowAggregatedInputPower,
+        jnxoptIfOMSnSinkCurrentHighAggregatedInputPower,
+        jnxoptIfOMSnSinkCurrentOutputPower,
+        jnxoptIfOMSnSinkCurrentLowOutputPower,
+        jnxoptIfOMSnSinkCurrentHighOutputPower,
+        jnxoptIfOMSnSinkIntervalSuspectedFlag,
+        jnxoptIfOMSnSinkIntervalLastAggregatedInputPower,
+        jnxoptIfOMSnSinkIntervalLowAggregatedInputPower,
+        jnxoptIfOMSnSinkIntervalHighAggregatedInputPower,
+        jnxoptIfOMSnSinkIntervalLastOutputPower,
+        jnxoptIfOMSnSinkIntervalLowOutputPower,
+        jnxoptIfOMSnSinkIntervalHighOutputPower,
+        jnxoptIfOMSnSinkCurDaySuspectedFlag,
+        jnxoptIfOMSnSinkCurDayLowAggregatedInputPower,
+        jnxoptIfOMSnSinkCurDayHighAggregatedInputPower,
+        jnxoptIfOMSnSinkCurDayLowOutputPower,
+        jnxoptIfOMSnSinkCurDayHighOutputPower,
+        jnxoptIfOMSnSinkPrevDaySuspectedFlag,
+        jnxoptIfOMSnSinkPrevDayLastAggregatedInputPower,
+        jnxoptIfOMSnSinkPrevDayLowAggregatedInputPower,
+        jnxoptIfOMSnSinkPrevDayHighAggregatedInputPower,
+        jnxoptIfOMSnSinkPrevDayLastOutputPower,
+        jnxoptIfOMSnSinkPrevDayLowOutputPower,
+        jnxoptIfOMSnSinkPrevDayHighOutputPower
+    } 
+    STATUS current 
+    DESCRIPTION
+      "A collection of pre-OTN performance monitoring 
+      objects applicable to OMSn interfaces that 
+      support sink functions."
+    ::= { jnxoptIfGroups 15 } 
+
+
+jnxoptIfOMSnSinkPreOtnPMThresholdGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOMSnSinkCurrentLowerInputPowerThreshold,
+        jnxoptIfOMSnSinkCurrentUpperInputPowerThreshold,
+        jnxoptIfOMSnSinkCurrentLowerOutputPowerThreshold,
+        jnxoptIfOMSnSinkCurrentUpperOutputPowerThreshold 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of pre-OTN performance monitoring 
+      threshold objects applicable to OMSn interfaces 
+      that support sink functions." 
+    ::= { jnxoptIfGroups 16 } 
+
+
+jnxoptIfOMSnSourcePreOtnPMGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOMSnSrcCurrentSuspectedFlag,
+        jnxoptIfOMSnSrcCurrentOutputPower,
+        jnxoptIfOMSnSrcCurrentLowOutputPower,
+        jnxoptIfOMSnSrcCurrentHighOutputPower,
+        jnxoptIfOMSnSrcCurrentAggregatedInputPower,
+        jnxoptIfOMSnSrcCurrentLowAggregatedInputPower,
+        jnxoptIfOMSnSrcCurrentHighAggregatedInputPower,
+        jnxoptIfOMSnSrcIntervalSuspectedFlag,
+        jnxoptIfOMSnSrcIntervalLastOutputPower,
+        jnxoptIfOMSnSrcIntervalLowOutputPower,
+        jnxoptIfOMSnSrcIntervalHighOutputPower,
+        jnxoptIfOMSnSrcIntervalLastAggregatedInputPower,
+        jnxoptIfOMSnSrcIntervalLowAggregatedInputPower,
+        jnxoptIfOMSnSrcIntervalHighAggregatedInputPower,
+        jnxoptIfOMSnSrcCurDaySuspectedFlag,
+        jnxoptIfOMSnSrcCurDayLowOutputPower,
+        jnxoptIfOMSnSrcCurDayHighOutputPower,
+        jnxoptIfOMSnSrcCurDayLowAggregatedInputPower,
+        jnxoptIfOMSnSrcCurDayHighAggregatedInputPower,
+        jnxoptIfOMSnSrcPrevDaySuspectedFlag,
+        jnxoptIfOMSnSrcPrevDayLastOutputPower,
+        jnxoptIfOMSnSrcPrevDayLowOutputPower,
+        jnxoptIfOMSnSrcPrevDayHighOutputPower,
+        jnxoptIfOMSnSrcPrevDayLastAggregatedInputPower,
+        jnxoptIfOMSnSrcPrevDayLowAggregatedInputPower,
+        jnxoptIfOMSnSrcPrevDayHighAggregatedInputPower 
+    }
+    STATUS current
+    DESCRIPTION
+      "A collection of pre-OTN performance monitoring 
+       objects applicable to OMSn interfaces that 
+       support source functions."
+    ::= { jnxoptIfGroups 17 } 
+
+
+jnxoptIfOMSnSourcePreOtnPMThresholdGroup OBJECT-GROUP 
+     OBJECTS { 
+         jnxoptIfOMSnSrcCurrentLowerOutputPowerThreshold,
+         jnxoptIfOMSnSrcCurrentUpperOutputPowerThreshold,
+         jnxoptIfOMSnSrcCurrentLowerInputPowerThreshold,
+         jnxoptIfOMSnSrcCurrentUpperInputPowerThreshold 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of pre-OTN performance monitoring 
+      threshold objects applicable to OMSn interfaces that 
+      that support source functions." 
+    ::= { jnxoptIfGroups 18 } 
+  
+
+jnxoptIfOChGroupCommonGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOChGroupDirectionality 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of configuration objects 
+      applicable to all OChGroup interfaces." 
+    ::= { jnxoptIfGroups 19 } 
+
+
+jnxoptIfOChGroupSinkPreOtnPMGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOChGroupSinkCurrentSuspectedFlag,
+        jnxoptIfOChGroupSinkCurrentAggregatedInputPower,
+        jnxoptIfOChGroupSinkCurrentLowAggregatedInputPower,
+        jnxoptIfOChGroupSinkCurrentHighAggregatedInputPower,
+        jnxoptIfOChGroupSinkCurrentOutputPower,
+        jnxoptIfOChGroupSinkCurrentLowOutputPower,
+        jnxoptIfOChGroupSinkCurrentHighOutputPower,
+        jnxoptIfOChGroupSinkIntervalSuspectedFlag,
+        jnxoptIfOChGroupSinkIntervalLastAggregatedInputPower,
+        jnxoptIfOChGroupSinkIntervalLowAggregatedInputPower,
+        jnxoptIfOChGroupSinkIntervalHighAggregatedInputPower,
+        jnxoptIfOChGroupSinkIntervalLastOutputPower,
+        jnxoptIfOChGroupSinkIntervalLowOutputPower,
+        jnxoptIfOChGroupSinkIntervalHighOutputPower,
+        jnxoptIfOChGroupSinkCurDaySuspectedFlag,
+        jnxoptIfOChGroupSinkCurDayLowAggregatedInputPower,
+        jnxoptIfOChGroupSinkCurDayHighAggregatedInputPower,
+        jnxoptIfOChGroupSinkCurDayLowOutputPower,
+        jnxoptIfOChGroupSinkCurDayHighOutputPower,
+        jnxoptIfOChGroupSinkPrevDaySuspectedFlag,
+        jnxoptIfOChGroupSinkPrevDayLastAggregatedInputPower,
+        jnxoptIfOChGroupSinkPrevDayLowAggregatedInputPower,
+        jnxoptIfOChGroupSinkPrevDayHighAggregatedInputPower,
+        jnxoptIfOChGroupSinkPrevDayLastOutputPower,
+        jnxoptIfOChGroupSinkPrevDayLowOutputPower,
+        jnxoptIfOChGroupSinkPrevDayHighOutputPower 
+    }
+    STATUS current
+    DESCRIPTION
+      "A collection of pre-OTN performance monitoring 
+      objects applicable to OChGroup interfaces that 
+      support sink functions."
+    ::= { jnxoptIfGroups 20 } 
+
+
+jnxoptIfOChGroupSinkPreOtnPMThresholdGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOChGroupSinkCurrentLowerInputPowerThreshold,
+        jnxoptIfOChGroupSinkCurrentUpperInputPowerThreshold,
+        jnxoptIfOChGroupSinkCurrentLowerOutputPowerThreshold,
+        jnxoptIfOChGroupSinkCurrentUpperOutputPowerThreshold
+ 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of pre-OTN performance monitoring 
+      threshold objects applicable to OChGroup interfaces 
+      that support sink functions." 
+    ::= { jnxoptIfGroups 21 } 
+
+
+jnxoptIfOChGroupSourcePreOtnPMGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOChGroupSrcCurrentSuspectedFlag,
+        jnxoptIfOChGroupSrcCurrentOutputPower,
+        jnxoptIfOChGroupSrcCurrentLowOutputPower,
+        jnxoptIfOChGroupSrcCurrentHighOutputPower,
+        jnxoptIfOChGroupSrcCurrentAggregatedInputPower,
+        jnxoptIfOChGroupSrcCurrentLowAggregatedInputPower,
+        jnxoptIfOChGroupSrcCurrentHighAggregatedInputPower,
+        jnxoptIfOChGroupSrcIntervalSuspectedFlag,
+        jnxoptIfOChGroupSrcIntervalLastOutputPower,
+        jnxoptIfOChGroupSrcIntervalLowOutputPower,
+        jnxoptIfOChGroupSrcIntervalHighOutputPower,
+        jnxoptIfOChGroupSrcIntervalLastAggregatedInputPower,
+        jnxoptIfOChGroupSrcIntervalLowAggregatedInputPower,
+        jnxoptIfOChGroupSrcIntervalHighAggregatedInputPower,
+        jnxoptIfOChGroupSrcCurDaySuspectedFlag,
+        jnxoptIfOChGroupSrcCurDayLowOutputPower,
+        jnxoptIfOChGroupSrcCurDayHighOutputPower,
+        jnxoptIfOChGroupSrcCurDayLowAggregatedInputPower,
+        jnxoptIfOChGroupSrcCurDayHighAggregatedInputPower,
+        jnxoptIfOChGroupSrcPrevDaySuspectedFlag,
+        jnxoptIfOChGroupSrcPrevDayLastOutputPower,
+        jnxoptIfOChGroupSrcPrevDayLowOutputPower,
+        jnxoptIfOChGroupSrcPrevDayHighOutputPower,
+        jnxoptIfOChGroupSrcPrevDayLastAggregatedInputPower,
+        jnxoptIfOChGroupSrcPrevDayLowAggregatedInputPower,
+        jnxoptIfOChGroupSrcPrevDayHighAggregatedInputPower
+    }
+    STATUS current
+    DESCRIPTION
+      "A collection of pre-OTN performance monitoring 
+      objects applicable to OChGroup interfaces that 
+      support source functions."
+    ::= { jnxoptIfGroups 22 } 
+
+
+jnxoptIfOChGroupSourcePreOtnPMThresholdGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOChGroupSrcCurrentLowerOutputPowerThreshold,
+        jnxoptIfOChGroupSrcCurrentUpperOutputPowerThreshold,
+        jnxoptIfOChGroupSrcCurrentLowerInputPowerThreshold,
+        jnxoptIfOChGroupSrcCurrentUpperInputPowerThreshold 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of pre-OTN performance monitoring 
+      threshold objects applicable to OChGroup interfaces that 
+      that support source functions." 
+    ::= { jnxoptIfGroups 23 } 
+
+
+jnxoptIfOChCommonGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOChDirectionality 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of configuration objects 
+      applicable to all OCh interfaces." 
+    ::= { jnxoptIfGroups 24 } 
+
+
+
+jnxoptIfOChSinkGroupBasic OBJECT-GROUP 
+    OBJECTS { 
+         jnxoptIfOChCurrentStatus 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of configuration objects 
+      applicable to all OCh interfaces that 
+      support sink functions." 
+    ::= { jnxoptIfGroups 25 } 
+
+
+jnxoptIfOChSinkPreOtnPMGroup OBJECT-GROUP 
+    OBJECTS {     
+        jnxoptIfOChSinkCurrentSuspectedFlag,
+        jnxoptIfOChSinkCurrentInputPower,
+        jnxoptIfOChSinkCurrentLowInputPower,
+        jnxoptIfOChSinkCurrentHighInputPower,
+        jnxoptIfOChSinkIntervalSuspectedFlag,
+        jnxoptIfOChSinkIntervalLastInputPower,
+        jnxoptIfOChSinkIntervalLowInputPower,
+        jnxoptIfOChSinkIntervalHighInputPower,
+        jnxoptIfOChSinkCurDaySuspectedFlag,
+        jnxoptIfOChSinkCurDayLowInputPower,
+        jnxoptIfOChSinkCurDayHighInputPower,
+        jnxoptIfOChSinkPrevDaySuspectedFlag,
+        jnxoptIfOChSinkPrevDayLastInputPower,
+        jnxoptIfOChSinkPrevDayLowInputPower,
+        jnxoptIfOChSinkPrevDayHighInputPower 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of pre-OTN performance monitoring 
+      objects applicable to OCh interfaces that 
+      support sink functions." 
+    ::= { jnxoptIfGroups 26 } 
+
+
+jnxoptIfOChSinkPreOtnPMThresholdGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOChSinkCurrentLowerInputPowerThreshold, 
+        jnxoptIfOChSinkCurrentUpperInputPowerThreshold 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of pre-OTN performance monitoring 
+      threshold objects applicable to OCh interfaces 
+      that support sink functions." 
+    ::= { jnxoptIfGroups 27 } 
+
+jnxoptIfOChSourcePreOtnPMGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOChSrcCurrentSuspectedFlag,
+        jnxoptIfOChSrcCurrentOutputPower,
+        jnxoptIfOChSrcCurrentLowOutputPower,
+        jnxoptIfOChSrcCurrentHighOutputPower,
+        jnxoptIfOChSrcIntervalSuspectedFlag,
+        jnxoptIfOChSrcIntervalLastOutputPower,
+        jnxoptIfOChSrcIntervalLowOutputPower,
+        jnxoptIfOChSrcIntervalHighOutputPower,
+        jnxoptIfOChSrcCurDaySuspectedFlag,
+        jnxoptIfOChSrcCurDayLowOutputPower,
+        jnxoptIfOChSrcCurDayHighOutputPower,
+        jnxoptIfOChSrcPrevDaySuspectedFlag,
+        jnxoptIfOChSrcPrevDayLastOutputPower,
+        jnxoptIfOChSrcPrevDayLowOutputPower,
+        jnxoptIfOChSrcPrevDayHighOutputPower 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of pre-OTN performance monitoring 
+      objects applicable to OCh interfaces that 
+      support source functions." 
+    ::= { jnxoptIfGroups 28 } 
+
+
+jnxoptIfOChSourcePreOtnPMThresholdGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfOChSrcCurrentLowerOutputPowerThreshold, 
+        jnxoptIfOChSrcCurrentUpperOutputPowerThreshold 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of pre-OTN performance monitoring 
+      threshold objects applicable to OCh interfaces 
+      that support source functions." 
+    ::= { jnxoptIfGroups 29 } 
+
+
+jnxoptIfOTUkCommonGroup OBJECT-GROUP 
+   OBJECTS { 
+       jnxoptIfOTUkDirectionality, 
+       jnxoptIfOTUkBitRateK 
+   } 
+   STATUS current 
+   DESCRIPTION 
+     "A collection of configuration objects 
+     applicable to all OTUk interfaces." 
+   ::= { jnxoptIfGroups 30 } 
+
+
+
+jnxoptIfOTUkSourceGroup OBJECT-GROUP
+    OBJECTS { 
+        jnxoptIfOTUkTraceIdentifierTransmitted, 
+        jnxoptIfOTUkSourceAdaptActive 
+    }
+    STATUS current 
+    DESCRIPTION
+      "A collection of configuration objects 
+      applicable to OTUk interfaces that 
+      support source functions."
+    ::= { jnxoptIfGroups 31 } 
+
+
+jnxoptIfOTUkSinkGroup OBJECT-GROUP
+    OBJECTS { 
+         jnxoptIfOTUkDAPIExpected,
+        jnxoptIfOTUkSAPIExpected,
+        jnxoptIfOTUkTraceIdentifierAccepted,
+        jnxoptIfOTUkTIMDetMode,
+        jnxoptIfOTUkTIMActEnabled,
+        jnxoptIfOTUkDEGThr,
+        jnxoptIfOTUkDEGM,
+        jnxoptIfOTUkSinkAdaptActive,
+        jnxoptIfOTUkSinkFECEnabled,
+        jnxoptIfOTUkCurrentStatus 
+    }
+    STATUS current 
+    DESCRIPTION
+      "A collection of configuration objects 
+      applicable to OTUk interfaces that 
+      support sink functions."
+    ::= { jnxoptIfGroups 32 } 
+
+
+jnxoptIfGCC0Group OBJECT-GROUP
+    OBJECTS { 
+        jnxoptIfGCC0Application, 
+        jnxoptIfGCC0RowStatus 
+    }
+    STATUS current 
+    DESCRIPTION 
+      "A collection of GCC0 configuration objects." 
+    ::= { jnxoptIfGroups 33 } 
+
+
+jnxoptIfODUkGroup OBJECT-GROUP
+   OBJECTS { 
+        jnxoptIfODUkDirectionality,
+        jnxoptIfODUkBitRateK,
+        jnxoptIfODUkTcmFieldsInUse,
+        jnxoptIfODUkPositionSeqCurrentSize,
+        jnxoptIfODUkPositionSeqPosition,
+        jnxoptIfODUkPositionSeqPointer,
+        jnxoptIfODUkTtpPresent
+    }
+    STATUS current 
+    DESCRIPTION 
+      "A collection of configuration objects 
+      applicable to all ODUk interfaces." 
+    ::= { jnxoptIfGroups 34 } 
+
+
+jnxoptIfODUkTtpSourceGroup OBJECT-GROUP
+    OBJECTS { 
+        jnxoptIfODUkTtpTraceIdentifierTransmitted 
+    }
+    STATUS current 
+    DESCRIPTION
+      "A collection of configuration objects 
+      applicable to all interfaces that support 
+      ODUk trail termination source functions."
+    ::= { jnxoptIfGroups 35 } 
+
+
+jnxoptIfODUkTtpSinkGroup OBJECT-GROUP
+     OBJECTS { 
+        jnxoptIfODUkTtpDAPIExpected,
+        jnxoptIfODUkTtpSAPIExpected,
+        jnxoptIfODUkTtpTraceIdentifierAccepted,
+        jnxoptIfODUkTtpTIMDetMode,
+        jnxoptIfODUkTtpTIMActEnabled,
+        jnxoptIfODUkTtpDEGThr,
+        jnxoptIfODUkTtpDEGM,
+        jnxoptIfODUkTtpCurrentStatus 
+    }
+    STATUS current 
+    DESCRIPTION
+      "A collection of ODUk configuration objects 
+      applicable to all interfaces that support 
+      ODUk trail termination sink functions."
+    ::= { jnxoptIfGroups 36 } 
+
+
+jnxoptIfODUkNimGroup OBJECT-GROUP
+     OBJECTS { 
+        jnxoptIfODUkNimDAPIExpected,
+        jnxoptIfODUkNimSAPIExpected,
+        jnxoptIfODUkNimTraceIdentifierAccepted,
+        jnxoptIfODUkNimTIMDetMode,
+        jnxoptIfODUkNimTIMActEnabled,
+        jnxoptIfODUkNimDEGThr,
+        jnxoptIfODUkNimDEGM,
+        jnxoptIfODUkNimCurrentStatus,
+        jnxoptIfODUkNimRowStatus
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of ODUk Nim configuration objects." 
+    ::= { jnxoptIfGroups 37 } 
+
+jnxoptIfGCC12Group OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfGCC12GCCPassThrough, 
+        jnxoptIfGCC12Application, 
+        jnxoptIfGCC12RowStatus 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of GCC12 configuration objects." 
+    ::= { jnxoptIfGroups 38 } 
+
+jnxoptIfODUkTCommonGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfODUkTRowStatus 
+    } 
+    STATUS current 
+    DESCRIPTION 
+     "A collection of configuration objects 
+     applicable to all ODUkT instances." 
+    ::= { jnxoptIfGroups 39 } 
+
+jnxoptIfODUkTSourceGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfODUkTTraceIdentifierTransmitted, 
+        jnxoptIfODUkTSourceLockSignalAdminState 
+    } 
+    STATUS current 
+    DESCRIPTION 
+      "A collection of configuration objects 
+      applicable to all ODUkT instances 
+      that provide source functions." 
+    ::= { jnxoptIfGroups 40 } 
+
+jnxoptIfODUkTSinkGroup OBJECT-GROUP 
+    OBJECTS { 
+        jnxoptIfODUkTDAPIExpected,
+        jnxoptIfODUkTSAPIExpected,
+        jnxoptIfODUkTTraceIdentifierAccepted,
+        jnxoptIfODUkTTIMDetMode,
+        jnxoptIfODUkTTIMActEnabled,
+        jnxoptIfODUkTDEGThr,
+        jnxoptIfODUkTDEGM,
+        jnxoptIfODUkTCurrentStatus
+    }
+    STATUS current
+    DESCRIPTION
+      "A collection of configuration objects 
+      applicable to all ODUkT instances 
+      that provide sink functions."
+    ::= { jnxoptIfGroups 41 } 
+
+
+jnxoptIfODUkTSinkGroupCtp OBJECT-GROUP 
+   OBJECTS { 
+       jnxoptIfODUkTSinkMode, 
+       jnxoptIfODUkTSinkLockSignalAdminState 
+   } 
+   STATUS current 
+   DESCRIPTION 
+     "A collection of configuration objects 
+     applicable to ODUkT instances not 
+     colocated with an ODUk TTP that 
+     provide sink functions." 
+   ::= { jnxoptIfGroups 42 } 
+
+
+jnxoptIfODUkTNimGroup OBJECT-GROUP 
+   OBJECTS { 
+       jnxoptIfODUkTNimDAPIExpected,
+       jnxoptIfODUkTNimSAPIExpected,
+       jnxoptIfODUkTNimTraceIdentifierAccepted,
+       jnxoptIfODUkTNimTIMDetMode,
+       jnxoptIfODUkTNimTIMActEnabled,
+       jnxoptIfODUkTNimDEGThr,
+       jnxoptIfODUkTNimDEGM,
+       jnxoptIfODUkTNimCurrentStatus,
+       jnxoptIfODUkTNimRowStatus 
+   } 
+   STATUS current 
+   DESCRIPTION 
+   "A collection of ODUkT Nim configuration objects." 
+   ::= { jnxoptIfGroups 43 } 
+
+
+-- compliance specifications 
+
+
+jnxoptIfOtnConfigCompl MODULE-COMPLIANCE 
+    STATUS current 
+    DESCRIPTION 
+      "Implementation requirements for the OTN configuration 
+      functions defined in this MIB module." 
+    MODULE -- this module
+    MANDATORY-GROUPS { 
+        jnxoptIfOTMnGroup, 
+        jnxoptIfOTSnCommonGroup 
+    }
+
+
+GROUP jnxoptIfOTSnSourceGroupFull
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalTransport(196) for which the corresponding 
+      instance of jnxoptIfOTSnDirectionality has the value 
+      source(2) or bidirectional(3), the corresponding 
+      instance of jnxoptIfOTMnReduced has the value false(2), 
+      and the corresponding instance of jnxoptIfOTMnInterfaceType 
+      specifies an OTMn interface type of 'IaDI'."
+
+
+GROUP jnxoptIfOTSnAPRStatusGroup
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalTransport(196) that support Automatic Power 
+      Reduction functions."
+
+GROUP jnxoptIfOTSnAPRControlGroup
+    DESCRIPTION
+      "This group is optional, but is recommended for interfaces 
+      of ifType opticalTransport(196) that provide Automatic 
+      Power Reduction control functions."
+
+
+GROUP jnxoptIfOTSnSinkGroupBasic
+     DESCRIPTION
+       "This group is mandatory for interfaces of ifType 
+       opticalTransport(196) for which the corresponding 
+       instance of jnxoptIfOTSnDirectionality has the value 
+       sink(1) or bidirectional(3)."
+
+GROUP jnxoptIfOTSnSinkGroupFull
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalTransport(196) for which the corresponding 
+      instance of jnxoptIfOTSnDirectionality has the value 
+      sink(1) or bidirectional(3), the corresponding 
+      instance of jnxoptIfOTMnReduced has the value false(2), 
+      and the corresponding instance of jnxoptIfOTMnInterfaceType 
+      specifies an OTMn interface type of 'IaDI'."
+
+
+GROUP jnxoptIfOMSnCommonGroup 
+    DESCRIPTION 
+      "This group is mandatory for interfaces of ifType 
+      opticalTransport(196) that support access to the OMS 
+      overhead information within the OTN Supervisory Channel."
+
+GROUP jnxoptIfOMSnSinkGroupBasic
+    DESCRIPTION
+     "This group is mandatory for interfaces of ifType 
+      opticalTransport(196) that support access to the OMS Overhead 
+      information within the OSC (OTN Supervisory Channel) 
+      for which the corresponding 
+      instance of jnxoptIfOMSnDirectionality has the value 
+      sink(1) or bidirectional(3)."
+
+
+GROUP jnxoptIfOChGroupCommonGroup 
+    DESCRIPTION 
+      "This group is mandatory for interfaces of ifType 
+      opticalChannelGroup(219)."
+
+
+GROUP jnxoptIfOChCommonGroup 
+   DESCRIPTION 
+      "This group is mandatory for interfaces of ifType 
+      opticalTransport(195)."
+
+
+GROUP jnxoptIfOChSinkGroupBasic
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalChannel(195) for which the corresponding 
+      instance of jnxoptIfOChDirectionality has the value 
+      sink(1) or bidirectional(3)."
+
+
+GROUP jnxoptIfOTUkCommonGroup 
+    DESCRIPTION 
+       "This group is mandatory for interfaces of ifType 
+       opticalChannel(195) that support OTUk layer functions."
+
+
+GROUP jnxoptIfOTUkSourceGroup
+     DESCRIPTION
+       "This group is mandatory for interfaces of ifType 
+       opticalChannel(195) that support OTUk layer functions 
+       and for which the corresponding instance of 
+       jnxoptIfOTUkDirectionality has the value source(2) or 
+       bidirectional(3)."
+
+
+GROUP jnxoptIfOTUkSinkGroup
+     DESCRIPTION
+       "This group is mandatory for interfaces of ifType 
+       opticalChannel(195) that support OTUk layer functions 
+       and for which the corresponding instance of 
+       jnxoptIfOTUkDirectionality has the value sink(1) or
+       bidirectional(3)."
+
+GROUP jnxoptIfGCC0Group
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalChannel(195) that support GCC0 access functions. 
+      It may be implemented only if the jnxoptIfOTUkCommonGroup 
+      is also implemented."
+
+
+GROUP jnxoptIfODUkGroup 
+    DESCRIPTION 
+      "This group is mandatory for interfaces of ifType 
+      opticalChannel(195) that support ODUk layer functions."
+
+
+GROUP jnxoptIfODUkTtpSourceGroup
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalChannel(195) for which the corresponding 
+      instance of jnxoptIfODUkTtpPresent has the value 
+      true(1) and for which the corresponding instance of 
+      jnxoptIfODUkDirectionality has the value source(2) or 
+      bidirectional(3). It may be implemented only if the 
+      jnxoptIfODUkGroup is also implemented."
+
+
+GROUP jnxoptIfODUkTtpSinkGroup
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalChannel(195) for which the corresponding 
+      instance of jnxoptIfODUkTtpPresent has the value 
+      true(1) and for which the corresponding instance of 
+      jnxoptIfODUkDirectionality has the value sink(1) or 
+      bidirectional(3). It may be implemented only if the 
+      jnxoptIfODUkGroup is also implemented."
+
+
+GROUP jnxoptIfODUkNimGroup
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalChannel(195) for which the corresponding 
+      instance of jnxoptIfODUkTtpPresent has the value 
+      false(2). It may be implemented only if the 
+      jnxoptIfODUkGroup is also implemented."
+
+
+GROUP jnxoptIfGCC12Group
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalChannel(195) that support GCC12 access functions. 
+      It may be implemented only if the jnxoptIfODUkGroup 
+      is also implemented."
+
+
+GROUP jnxoptIfODUkTCommonGroup
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalChannel(195) that support intrusive 
+      tandem connection monitoring. It may be implemented 
+      only if the jnxoptIfODUkGroup is also implemented."
+
+
+GROUP jnxoptIfODUkTSourceGroup
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalChannel(195) that support intrusive 
+      tandem connection monitoring and for which
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value false(2), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value true(1). 
+      It may be implemented only if the jnxoptIfODUkGroup is 
+      also implemented."
+
+
+GROUP jnxoptIfODUkTSinkGroup
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalChannel(195) that support intrusive 
+      tandem connection monitoring and for which
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value true(1), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value false(2). 
+      It may be implemented only if the jnxoptIfODUkGroup is 
+      also implemented."
+
+
+GROUP jnxoptIfODUkTSinkGroupCtp
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalChannel(195) that support intrusive 
+      tandem connection monitoring and for which 
+      jnxoptIfODUkTtpPresent is false(2) and
+      (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or 
+      (ii) jnxoptIfODUkDirectionality has the value sink(1) and 
+      jnxoptIfODUkTCodirectional has the value true(1), or 
+      (iii) jnxoptIfODUkDirectionality has the value source(3) and 
+      jnxoptIfODUkTCodirectional has the value false(2). 
+      It may be implemented only if the jnxoptIfODUkGroup and 
+      jnxoptIfODUkTSinkGroup are also implemented." 
+
+
+GROUP jnxoptIfODUkTNimGroup
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalChannel(195) that support non-intrusive 
+      tandem connection monitoring. It may be implemented 
+      only if the jnxoptIfODUkGroup is also implemented."
+    ::= { jnxoptIfCompl 1 } 
+
+
+jnxoptIfPreOtnPMCompl MODULE-COMPLIANCE 
+    STATUS current 
+    DESCRIPTION 
+      "Implementation requirements for Pre-OTN performance 
+      monitoring functions defined in this MIB module."
+    MODULE -- this module
+    MANDATORY-GROUPS { 
+        jnxoptIfPerfMonGroup 
+    }
+
+GROUP jnxoptIfOTSnSinkPreOtnPMGroup
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalTransport(196) that support OTSn sink 
+      functions (i.e., for which the corresponding instance 
+      of jnxoptIfOTSnDirectionality -- if implemented -- has 
+      the value sink(1) or bidirectional(3))."
+
+
+GROUP jnxoptIfOTSnSinkPreOtnPMThresholdGroup
+    DESCRIPTION
+      "This group is mandatory if and only if TCA notifications 
+      are implemented. If the objects of this group are instantiated 
+      then the implementation must also provide, in an 
+      enterprise MIB, suitable TCA notification definitions and 
+      notification control objects. Implementation of the 
+      jnxoptIfOTSnSinkPreOtnPMGroup is a prerequisite for 
+      implementing this group."
+
+
+GROUP jnxoptIfOTSnSourcePreOtnPMGroup
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalTransport(196) that support OTSn source 
+      functions (i.e., for which the corresponding instance 
+      of jnxoptIfOTSnDirectionality -- if implemented -- has 
+      the value source(2) or bidirectional(3))."
+
+
+GROUP jnxoptIfOTSnSourcePreOtnPMThresholdGroup 
+    DESCRIPTION
+      "This group is mandatory if and only if TCA notifications 
+      are implemented. If the objects of this group are instantiated 
+      then the implementation must also provide, in an 
+      enterprise MIB, suitable TCA notification definitions and 
+      notification control objects. Implementation of the 
+      jnxoptIfOTSnSourcePreOtnPMGroup is a prerequisite for 
+      implementing this group "
+
+
+GROUP jnxoptIfOMSnSinkPreOtnPMGroup 
+   DESCRIPTION
+     "This group is optional. It may be implemented by systems 
+      with the necessary instrumentation on interfaces of ifType 
+      opticalTransport(196) that support OMSn sink functions 
+      (i.e., for which the corresponding instance of 
+      jnxoptIfOMSnDirectionality -- if implemented -- has the value 
+      sink(1) or bidirectional(3))."
+
+
+GROUP jnxoptIfOMSnSinkPreOtnPMThresholdGroup 
+   DESCRIPTION
+     "This group is mandatory if and only if TCA notifications 
+     are implemented. If the objects of this group are instantiated 
+     then the implementation must also provide, in an 
+     enterprise MIB, suitable TCA notification definitions and 
+     notification control objects. Implementation of the 
+     jnxoptIfOMSnSinkPreOtnPMGroup is a prerequisite for 
+     implementing this group "
+
+
+GROUP jnxoptIfOMSnSourcePreOtnPMGroup 
+    DESCRIPTION
+      "This group is optional. It may be implemented by systems 
+      with the necessary instrumentation on interfaces of ifType 
+      opticalTransport(196) that support OMSn source functions 
+      (i.e., for which the corresponding instance of 
+      jnxoptIfOMSnDirectionality -- if implemented -- has the value 
+      source(2) or bidirectional(3))."
+
+
+GROUP jnxoptIfOMSnSourcePreOtnPMThresholdGroup 
+    DESCRIPTION
+      "This group is mandatory if and only if TCA notifications 
+      are implemented. If the objects of this group are instantiated 
+      then the implementation must also provide, in an 
+      enterprise MIB, suitable TCA notification definitions and 
+      notification control objects. Implementation of the 
+      jnxoptIfOMSnSourcePreOtnPMGroup is a prerequisite for 
+      implementing this group "
+
+
+GROUP jnxoptIfOChGroupSinkPreOtnPMGroup 
+    DESCRIPTION
+      "This group is optional. It may be implemented by systems 
+      with the necessary instrumentation on interfaces of ifType 
+      opticalChannelGroup(219) that support OChGroup sink functions 
+      (i.e., for which the corresponding instance of 
+      jnxoptIfOChGroupDirectionality -- if implemented -- has the value 
+      sink(1) or bidirectional(3))."
+
+
+GROUP jnxoptIfOChGroupSinkPreOtnPMThresholdGroup
+    DESCRIPTION
+      "This group is mandatory if and only if TCA notifications 
+      are implemented. If the objects of this group are instantiated 
+      then the implementation must also provide, in an 
+      enterprise MIB, suitable TCA notification definitions and 
+      notification control objects. Implementation of the 
+      jnxoptIfOChGroupSinkPreOtnPMGroup is a prerequisite for 
+      implementing this group "
+
+
+GROUP jnxoptIfOChGroupSourcePreOtnPMGroup
+    DESCRIPTION
+      "This group is optional. It may be implemented by systems 
+      with the necessary instrumentation on interfaces of ifType 
+      opticalChannelGroup(219) that support OChGroup source functions 
+      (i.e., for which the corresponding instance of 
+      jnxoptIfOChGroupDirectionality -- if implemented -- has the value 
+      source(2) or bidirectional(3))."
+
+
+GROUP jnxoptIfOChGroupSourcePreOtnPMThresholdGroup
+    DESCRIPTION
+      "This group is mandatory if and only if TCA notifications 
+      are implemented. If the objects of this group are instantiated 
+      then the implementation must also provide, in an 
+      enterprise MIB, suitable TCA notification definitions and 
+      notification control objects. Implementation of the 
+      jnxoptIfOChGroupSourcePreOtnPMGroup is a prerequisite for 
+      implementing this group "
+
+
+GROUP jnxoptIfOChSinkPreOtnPMGroup
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalChannel(195) that support OCh sink functions 
+      (i.e., for which the corresponding instance of 
+      jnxoptIfOChDirectionality -- if implemented -- has the 
+      value sink(1) or bidirectional(3))."
+
+
+GROUP jnxoptIfOChSinkPreOtnPMThresholdGroup 
+    DESCRIPTION 
+      "This group is mandatory if and only if TCA notifications 
+      are implemented. If the objects of this group are instantiated 
+      then the implementation must also provide, in an 
+      enterprise MIB, suitable TCA notification definitions and 
+      notification control objects. Implementation of the 
+      jnxoptIfOChSinkPreOtnPMGroup is a prerequisite for 
+      implementing this group "
+
+
+GROUP jnxoptIfOChSourcePreOtnPMGroup
+    DESCRIPTION
+      "This group is mandatory for interfaces of ifType 
+      opticalChannel(195) that support OCh source functions 
+      (i.e., for which the corresponding instance of 
+      jnxoptIfOChDirectionality -- if implemented -- has the 
+      value source(2) or bidirectional(3))."
+
+
+GROUP jnxoptIfOChSourcePreOtnPMThresholdGroup
+    DESCRIPTION
+      "This group is mandatory if and only if TCA notifications 
+      are implemented. If the objects of this group are instantiated 
+      then the implementation must also provide, in an 
+      enterprise MIB, suitable TCA notification definitions and 
+      notification control objects. Implementation of the 
+      jnxoptIfOChSourcePreOtnPMGroup is a prerequisite for 
+      implementing this group "
+    ::= { jnxoptIfCompl 2 } 
+
+
+END 
+
+
+
+
+
+
+