Initial commitHEADmain

1 files changed, 484 insertions, 0 deletions

diff --git a/MIBS/dlink/DLINKSW-CPU-PROTECT-MIB b/MIBS/dlink/DLINKSW-CPU-PROTECT-MIB
new file mode 100644
index 0000000..6d577fd
--- /dev/null
+++ b/MIBS/dlink/DLINKSW-CPU-PROTECT-MIB
@@ -0,0 +1,484 @@
+

+

+--  *****************************************************************

+--  DLINKSW-CPU-PROTECT-MIB.mib : CPU Protection MIB

+-- 

+--  Copyright (c) 2012 D-Link Corporation, all rights reserved.

+--   

+--  *****************************************************************

+

+	DLINKSW-CPU-PROTECT-MIB DEFINITIONS ::= BEGIN

+ 

+		IMPORTS					

+			OBJECT-GROUP, MODULE-COMPLIANCE			

+				FROM SNMPv2-CONF			

+			Integer32, Counter64, OBJECT-TYPE, MODULE-IDENTITY			

+				FROM SNMPv2-SMI						

+			TEXTUAL-CONVENTION			

+				FROM SNMPv2-TC

+			dlinkIndustrialCommon			

+				FROM DLINK-ID-REC-MIB;		

+	

+	

+		dlinkSwCpuProtectMIB MODULE-IDENTITY 

+			LAST-UPDATED "201208080000Z"		

+            ORGANIZATION "D-Link Corp."

+            CONTACT-INFO

+                "        D-Link Corporation

+

+                 Postal: No. 289, Sinhu 3rd Rd., Neihu District,

+                         Taipei City 114, Taiwan, R.O.C

+                 Tel:     +886-2-66000123

+                 E-mail: tsd@dlink.com.tw

+                "

+			DESCRIPTION 

+				"The MIB module for managing CPU protection."

+			REVISION        "201208080000Z"

+            DESCRIPTION

+                "Initial version of this MIB module."	

+			::= { dlinkIndustrialCommon 19 }

+

+		

+	

+--

+-- Textual conventions

+--

+	

+		CpuProtectProtocolType ::= TEXTUAL-CONVENTION

+			STATUS current

+			DESCRIPTION 

+				"Represents a protocol type.

+				Note that a particular agent may support only certain protocol

+				types. Thus, the valid values of this object are project

+				dependent.

+				An agent may respond with an error (e.g., 'inconsistentValue ')

+				to a management SET operation which attempts to modify

+				the value to one which is not supported by the managed device. 

+				arp(1)          indicates IP Address Resolution Protocol (ARP). 

+				bgp(2)          indicates Border Gateway Protocol.

+				dhcp(3)         indicates Dynamic Host Configuration Protocol.

+				dhcpv6(4)       indicates Dynamic Host Configuration Protocol for IPv6.

+				dns(5)          indicates Domain Name Services.                      

+				dot1x(6)        indicates IEEE 802.1X (Port Based Network Access Control).

+				dvmrp(7)        indicates Distance Vector Multicast Routing Protocol.

+				gvrp(8)         indicates GARP VLAN Registration Protocol.           

+				icmp(9)         indicates IPv4 Internet Control Message Protocol.    

+				icmpv6Ndp(10)   indicates IPv6 ICMP Neighbor Discover Protocol (NS/NA/RS/RA).

+				icmpv6Other(11) indicates IPv6 ICMP except NDP NS/NA/RS/RA.

+				igmp(12)        indicates Internet Group Management Protocol.   

+				lacp(13),       indicates Link Aggregation Control Protocol.    

+				ntp(14),        indicates Network Time Protocol.                

+				ospf(15),       indicates Open Shortest Path First.             

+				ospfv3(16),     indicates OSPF for IPv6.

+				pim(17),        indicates Protocol Independent Multicast.         

+				pppoe(18),      indicates Point-to-Point Protocol over Ethernet.  

+				rip(19),        indicates Routing Information Protocol.           

+				ripng(20),      indicates Routing Information Protocol for IPv6.

+				snmp(21),       indicates Simple Network Management Protocol.    

+				ssh(22),        indicates Secured shell.                          

+				stp(23),        indicates Spanning Tree Protocol (IEEE 802.1D).        

+				telnet(24),     indicates Telnet.                                 

+				tftp(25),       indicates Trivial File Transfer Protocol.         

+				vrrp(26),       indicates Virtual Router Redundancy Protocol.     

+				web(27)         indicates HTTP and HTTPS.      				                

+				"

+			SYNTAX INTEGER

+				{

+				arp(1),

+				bgp(2),

+				dhcp(3),

+				dhcpv6(4),

+				dns(5),

+				dot1x(6),

+				dvmrp(7),

+				gvrp(8),

+				icmp(9),

+				icmpv6Ndp(10),

+				icmpv6Other(11),

+				igmp(12),

+				lacp(13),

+				ntp(14),

+				ospf(15),

+				ospfv3(16),

+				pim(17),

+				pppoe(18),

+				rip(19),

+				ripng(20),

+				snmp(21),

+				ssh(22),

+				stp(23),

+				telnet(24),

+				tftp(25),

+				vrrp(26),

+				web(27)

+				}

+

+		MaxRate ::= TEXTUAL-CONVENTION		

+		 	STATUS current

+			DESCRIPTION 

+				"The range for configuring rate-limit in packet per second (pps).

+				Note that a particular agent may support different rate range.

+				Thus, the valid values are project dependent.

+				An agent may respond with an error (e.g., 'inconsistentValue ')

+				to a management SET operation which attempts to modify

+				the value to one which is not supported by the managed device.

+				The value -1 has a special meaning. When this object is

+                set to -1, there is no rate-limit of the entry."

+			SYNTAX Integer32 (-1 | 0..65535)

+

+		UnitID ::= TEXTUAL-CONVENTION

+			STATUS current

+			DESCRIPTION 

+				"This object indicates the slot (for a chassis device) or 

+				unit number (for stacking device).				

+				For a standalone device, 0 is used for UnitID.

+				Note that a particular agent may support different range

+				of unit/slot ID.

+				Thus, the valid values are project dependent.

+				An agent may respond with an error (e.g., 'inconsistentValue ')

+				to a management SET operation which attempts to modify

+				the value to one which is not supported by the managed device.				 

+				"

+			SYNTAX Integer32 (0 | 1..64)

+

+	

+--

+-- Node definitions

+--

+	

+		dCpuProtectMIBNotifications OBJECT IDENTIFIER ::= { dlinkSwCpuProtectMIB 0 }		

+		dCpuProtectMIBObjects       OBJECT IDENTIFIER ::= { dlinkSwCpuProtectMIB 1 }

+        dCpuProtectMIBConformance   OBJECT IDENTIFIER ::= { dlinkSwCpuProtectMIB 2 }

+

+									

+		dCpuProtectMIBObjectsCtrl OBJECT IDENTIFIER ::= { dCpuProtectMIBObjects 2 }

+				

+--  ***************************************************************************

+--  dCpuProtectProtoRateLimitTable

+--  ***************************************************************************      

+		dCpuProtectProtoRateLimitTable OBJECT-TYPE

+			SYNTAX      SEQUENCE OF DCpuProtectProtoRateLimitEntry

+			MAX-ACCESS  not-accessible

+			STATUS      current

+			DESCRIPTION

+				"The object configure the rate-limit of traffic destined to CPU 

+				based on protocol type."

+			::= { dCpuProtectMIBObjectsCtrl 1 }

+		

+		dCpuProtectProtoRateLimitEntry OBJECT-TYPE

+			SYNTAX      DCpuProtectProtoRateLimitEntry

+			MAX-ACCESS  not-accessible

+			STATUS      current

+			DESCRIPTION

+				"The object configures rate-limit control based on a specific

+				protocol type."

+			INDEX { dCpuProtectProtoRLType }

+			::= { dCpuProtectProtoRateLimitTable 1 }

+		

+		DCpuProtectProtoRateLimitEntry ::=

+			SEQUENCE { 

+				dCpuProtectProtoRLType          CpuProtectProtocolType,

+				dCpuProtectProtoRLRate			MaxRate,

+				dCpuProtectProtoRLClearCounter	INTEGER				

+			}

+

+		dCpuProtectProtoRLType OBJECT-TYPE

+			SYNTAX      CpuProtectProtocolType

+			MAX-ACCESS  not-accessible

+			STATUS      current

+			DESCRIPTION

+				"This object indicates the protocol type."

+			::= { dCpuProtectProtoRateLimitEntry 1 }

+		

+		dCpuProtectProtoRLRate OBJECT-TYPE

+			SYNTAX      MaxRate

+			MAX-ACCESS  read-create

+			STATUS      current

+			DESCRIPTION

+				"This object indicates the rate-limit of the specific 

+				protocol type.

+				The value of -1 has the special meaning of identifying 

+				that there is no rate-limit of the specific protocol type."

+			DEFVAL      { -1 }	

+			::= { dCpuProtectProtoRateLimitEntry 2 }

+

+		

+		dCpuProtectProtoRLClearCounter OBJECT-TYPE

+			SYNTAX      INTEGER

+				{   clear(1),

+				    noOp(2)

+				}

+			MAX-ACCESS  read-create

+			STATUS current

+			DESCRIPTION

+				"This object is used to reset the counter of the specific 

+				protocol type when set to 'clear'.

+				No action is taken if this object is set to 'noOp'.

+				When read, the value 'noOp' is returned."

+			DEFVAL      { noOp }	

+			::= { dCpuProtectProtoRateLimitEntry 3 }

+				

+

+		

+--  ***************************************************************************

+--  dCpuProtectSubIntfRLTable

+--  ***************************************************************************

+		dCpuProtectSubIntfRLTable OBJECT-TYPE

+			SYNTAX      SEQUENCE OF DCpuProtectSubIntfRLEntry

+			MAX-ACCESS  not-accessible

+			STATUS      current

+			DESCRIPTION

+				"This table consists of the rate-limit information of the 

+				sub-interface."

+			::= { dCpuProtectMIBObjectsCtrl 2 }

+		

+		dCpuProtectSubIntfRLEntry OBJECT-TYPE

+			SYNTAX      DCpuProtectSubIntfRLEntry

+			MAX-ACCESS  not-accessible

+			STATUS      current

+			DESCRIPTION

+				"The object configure rate-limit control based on a specific 

+				sub-interface."

+			INDEX { dCpuProtectSubIntfRLType }

+			::= { dCpuProtectSubIntfRLTable 1 }

+		

+		DCpuProtectSubIntfRLEntry ::=

+			SEQUENCE { 

+				dCpuProtectSubIntfRLType 				INTEGER,

+				dCpuProtectSubIntfRLRate				MaxRate,

+				dCpuProtectSubIntfRLClearCounter		INTEGER

+			 }

+

+		dCpuProtectSubIntfRLType OBJECT-TYPE

+			SYNTAX      INTEGER

+				{   manage(1),

+				    protocol(2),

+				    route(3)

+				}

+			MAX-ACCESS  not-accessible

+			STATUS      current

+			DESCRIPTION

+				"This object indicates the type of sub-interface."

+			::= { dCpuProtectSubIntfRLEntry 1 }

+		

+		dCpuProtectSubIntfRLRate OBJECT-TYPE

+			SYNTAX      MaxRate

+			MAX-ACCESS  read-create

+			STATUS      current

+			DESCRIPTION

+				"This object indicates the rate-limit of the specific 

+				sub-interface.

+				The value of -1 has the special meaning of identifying 

+				that there is no rate-limit of the specific sub-interface."	

+			DEFVAL      { -1 }				

+			::= { dCpuProtectSubIntfRLEntry 2 }

+		

+		dCpuProtectSubIntfRLClearCounter OBJECT-TYPE

+			SYNTAX      INTEGER

+				{   clear(1),

+				    noOp(2)

+				}

+			MAX-ACCESS  read-create

+			STATUS      current

+			DESCRIPTION

+				"This object is used to reset the counter of the specific 

+				sub-interface when set to 'clear'.

+				No action is taken if this object is set to 'noOp'.

+				When read, the value 'noOp' is returned."

+		    DEFVAL      { noOp }

+			::= { dCpuProtectSubIntfRLEntry 3 }

+				

+		dCpuProtectMIBObjectsCounters OBJECT IDENTIFIER 

+		::= { dCpuProtectMIBObjects 3 }

+		

+--  ***************************************************************************

+--  dCpuProtectProtoRLCntTable

+--  ***************************************************************************

+		dCpuProtectProtoRLCntTable OBJECT-TYPE

+			SYNTAX      SEQUENCE OF DCpuProtectProtoRLCntEntry

+			MAX-ACCESS  not-accessible

+			STATUS      current

+			DESCRIPTION

+				"This table consists of the traffic statistics by protocol type."

+			::= { dCpuProtectMIBObjectsCounters 1 }

+		

+		dCpuProtectProtoRLCntEntry OBJECT-TYPE

+			SYNTAX      DCpuProtectProtoRLCntEntry

+			MAX-ACCESS  not-accessible

+			STATUS      current

+			DESCRIPTION

+				"The per unit/slot traffic statistics about a protocol type.				

+				Objects in	this table are read-only and appear

+				automatically whenever the value of dCpuProtectProtoRLRate of a row 

+				in the dCpuProtectProtoRateLimitTable is not -1 (no-limit)."

+			INDEX { dCpuProtectProtoRLCntType, dCpuProtectProtoRLCntUnitID }

+			::= { dCpuProtectProtoRLCntTable 1 }

+		

+		DCpuProtectProtoRLCntEntry ::=

+			SEQUENCE { 

+				dCpuProtectProtoRLCntType       CpuProtectProtocolType,

+				dCpuProtectProtoRLCntUnitID	    UnitID,

+				dCpuProtectProtoRLCntTotalCnt   Counter64,

+				dCpuProtectProtoRLCntDropCnt    Counter64

+			 }

+

+		dCpuProtectProtoRLCntType OBJECT-TYPE

+			SYNTAX      CpuProtectProtocolType

+			MAX-ACCESS  not-accessible

+			STATUS      current

+			DESCRIPTION

+				"This object indicates the Protocol type."

+			::= { dCpuProtectProtoRLCntEntry 1 }

+                       		

+		dCpuProtectProtoRLCntUnitID OBJECT-TYPE

+			SYNTAX      UnitID

+			MAX-ACCESS  not-accessible

+			STATUS      current

+			DESCRIPTION

+				"This object indicates the unit/slot ID (for a chassis device) 

+				or unit number (for stacking device). For a standalone device, 

+				0 is used for UnitID."

+			::= { dCpuProtectProtoRLCntEntry 2 }

+		

+		dCpuProtectProtoRLCntTotalCnt OBJECT-TYPE

+			SYNTAX      Counter64

+			MAX-ACCESS  read-only

+			STATUS      current

+			DESCRIPTION

+				"This object indicates the counter which counts the packets

+				received by CPU (per unit/slot) for the protocol type."

+			::= { dCpuProtectProtoRLCntEntry 3 }

+		

+		dCpuProtectProtoRLCntDropCnt OBJECT-TYPE

+			SYNTAX      Counter64

+			MAX-ACCESS  read-only

+			STATUS      current

+			DESCRIPTION

+				"This object indicates the counter which counts the dropped

+				packets due to exceeding the configured rate-limit."

+			::= { dCpuProtectProtoRLCntEntry 4 }

+		

+--  ***************************************************************************

+--  dCpuProtectSubIntfRLCounterTable

+--  ***************************************************************************

+		dCpuProtectSubIntfRLCounterTable OBJECT-TYPE

+			SYNTAX      SEQUENCE OF DCpuProtectSubIntfRLCounterEntry

+			MAX-ACCESS  not-accessible

+			STATUS      current

+			DESCRIPTION

+				"This table consists of the traffic statistics by sub-interface."

+			::= { dCpuProtectMIBObjectsCounters 2 }

+		

+		dCpuProtectSubIntfRLCounterEntry OBJECT-TYPE

+			SYNTAX DCpuProtectSubIntfRLCounterEntry

+			MAX-ACCESS  not-accessible

+			STATUS      current

+			DESCRIPTION

+				"The per unit traffic statistics about a sub-interface.				

+				Objects in	this table are read-only and appear

+				automatically whenever the value of dCpuProtectSubIntfRLRate of a row 

+				in the dCpuProtectSubIntfRLTable is not -1 (no-limit)."								

+			INDEX { dCpuProtectSubIntfRLCntType, dCpuProtectSubIntfRLCntUnitID }

+			::= { dCpuProtectSubIntfRLCounterTable 1 }

+		

+		DCpuProtectSubIntfRLCounterEntry ::=

+			SEQUENCE { 

+				dCpuProtectSubIntfRLCntType       INTEGER,

+				dCpuProtectSubIntfRLCntUnitID     UnitID,

+				dCpuProtectSubIntfRLCntTotalCnt   Counter64,

+				dCpuProtectSubIntfRLCntDropCnt    Counter64

+			 }

+

+		dCpuProtectSubIntfRLCntType OBJECT-TYPE

+			SYNTAX      INTEGER

+				{   manage(1),

+				    protocol(2),

+				    route(3)

+				}

+			MAX-ACCESS  not-accessible

+			STATUS      current

+			DESCRIPTION

+				"This object indicates the type of sub-interface."

+			::= { dCpuProtectSubIntfRLCounterEntry 1 }

+		

+		dCpuProtectSubIntfRLCntUnitID OBJECT-TYPE

+			SYNTAX      UnitID

+			MAX-ACCESS  not-accessible

+			STATUS      current

+			DESCRIPTION

+				"This object indicates the slot (for a chassis device) or 

+				unit number (for stacking device). For a standalone device, 

+				0 is used for UnitID."

+			::= { dCpuProtectSubIntfRLCounterEntry 2 }

+		

+		dCpuProtectSubIntfRLCntTotalCnt OBJECT-TYPE

+			SYNTAX      Counter64

+			MAX-ACCESS  read-only

+			STATUS      current

+			DESCRIPTION

+				"This object indicates the counter which counts the packets

+				 received by CPU (per unit/slot) for the subinterface."

+			::= { dCpuProtectSubIntfRLCounterEntry 3 }

+		

+		dCpuProtectSubIntfRLCntDropCnt OBJECT-TYPE

+			SYNTAX      Counter64

+			MAX-ACCESS  read-only

+			STATUS      current

+			DESCRIPTION

+				"This object indicates the counter which counts the dropped

+				packets due to exceeding the configured rate-limit."

+			::= { dCpuProtectSubIntfRLCounterEntry 4 }

+

+--  ***************************************************************************	

+--  Conformance

+--  ***************************************************************************		

+	    		

+	    dCpuProtectMIBCompliances OBJECT IDENTIFIER ::= { dCpuProtectMIBConformance 1 }

+	

+	    dCpuProtectMIBCompliance MODULE-COMPLIANCE

+	        STATUS      current

+		    DESCRIPTION 

+			    "The compliance statement for entities which implement the 

+			    DLINKSW-CPU-PROTECT-MIB."

+		    MODULE -- this module

+		    MANDATORY-GROUPS { dCpuProtectProtoGroup }

+		    

+		    GROUP dCpuProtectSubIntfGroup

+		    DESCRIPTION 

+		        "This group is required only if the agent implements                

+			    the rate-limit for traffic destined to CPU by sub-interface type."				

+		    ::= { dCpuProtectMIBCompliances 1 }

+

+		

+        dCpuProtectMIBGroups OBJECT IDENTIFIER ::= { dCpuProtectMIBConformance 2 }

+                

+		dCpuProtectProtoGroup OBJECT-GROUP

+		    OBJECTS 

+		        {   dCpuProtectProtoRLRate, 

+		            dCpuProtectProtoRLClearCounter, 		             

+				    dCpuProtectProtoRLCntTotalCnt, 

+			    	dCpuProtectProtoRLCntDropCnt 

+				}

+		    STATUS      current

+		    DESCRIPTION 

+			    "A collection of objects providing the configuration or 

+			    statistics about the rate-limit of traffic destined to 

+			    CPU by protocol type."

+		    ::= { dCpuProtectMIBGroups 1 }

+		

+		dCpuProtectSubIntfGroup OBJECT-GROUP

+		    OBJECTS 

+		        {   dCpuProtectSubIntfRLRate, 

+		            dCpuProtectSubIntfRLClearCounter, 

+			        dCpuProtectSubIntfRLCntTotalCnt, 

+			        dCpuProtectSubIntfRLCntDropCnt 

+			    }

+		    STATUS      current

+			DESCRIPTION 

+				"A collection of objects providing the configuration or 

+				statistics about the rate-limit of traffic destined to 

+				CPU by sub-interface type."

+			::= { dCpuProtectMIBGroups 2 }			    

+	   	

+	END

+