summaryrefslogtreecommitdiff
path: root/MIBS/cisco/CISCO-DOT11-IF-MIB
diff options
context:
space:
mode:
authorDavid Leutgeb <david.leutgeb@mannundmouse.com>2023-12-05 12:25:34 +0100
committerDavid Leutgeb <david.leutgeb@mannundmouse.com>2023-12-05 12:25:34 +0100
commit98a672123c7872f6b9b75a9a2b6bb3aea504de6a (patch)
tree9b13bd7f563c3198047bd359195327cf28b3caf0 /MIBS/cisco/CISCO-DOT11-IF-MIB
downloadmibs-main.tar.gz
mibs-main.zip
Initial commitHEADmain
Diffstat (limited to 'MIBS/cisco/CISCO-DOT11-IF-MIB')
-rw-r--r--MIBS/cisco/CISCO-DOT11-IF-MIB4482
1 files changed, 4482 insertions, 0 deletions
diff --git a/MIBS/cisco/CISCO-DOT11-IF-MIB b/MIBS/cisco/CISCO-DOT11-IF-MIB
new file mode 100644
index 0000000..828d0a4
--- /dev/null
+++ b/MIBS/cisco/CISCO-DOT11-IF-MIB
@@ -0,0 +1,4482 @@
+-- *****************************************************************
+-- CISCO-DOT11-IF-MIB.my: CISCO IEEE 802.11 INTERFACE MIB file
+--
+-- April 2002, Francis Pang
+--
+-- Copyright (c) 2002-2007 by Cisco Systems, Inc.
+-- All rights reserved.
+-- *****************************************************************
+--
+CISCO-DOT11-IF-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+ MODULE-IDENTITY,
+ OBJECT-TYPE,
+ NOTIFICATION-TYPE,
+ Integer32,
+ Unsigned32,
+ Counter32
+ FROM SNMPv2-SMI
+ MODULE-COMPLIANCE,
+ OBJECT-GROUP,
+ NOTIFICATION-GROUP
+ FROM SNMPv2-CONF
+ TEXTUAL-CONVENTION,
+ MacAddress,
+ RowStatus,
+ TruthValue
+ FROM SNMPv2-TC
+ SnmpAdminString
+ FROM SNMP-FRAMEWORK-MIB
+ ifIndex
+ FROM IF-MIB
+ dot11AuthenticationAlgorithmsIndex,
+ dot11SupportedDataRatesRxIndex
+ FROM IEEE802dot11-MIB
+ ciscoMgmt
+ FROM CISCO-SMI;
+
+
+-- ********************************************************************
+-- * MODULE IDENTITY
+-- ********************************************************************
+
+ciscoDot11IfMIB MODULE-IDENTITY
+ LAST-UPDATED "200612200000Z"
+ ORGANIZATION "Cisco System Inc."
+ CONTACT-INFO
+ " Cisco Systems
+ Customer Service
+
+ Postal: 170 West Tasman Drive,
+ San Jose CA 95134-1706.
+ USA
+
+ Tel: +1 800 553-NETS
+
+ E-mail: cs-dot11@cisco.com"
+ DESCRIPTION
+ "This MIB module provides network management
+ support for Cisco IEEE 802.11 Wireless LAN
+ type device (Access Point) radio interfaces.
+
+ ACRONYMS
+ AES
+ Advanced Encryption Standard
+
+ AP
+ Access point
+
+ AID
+ Association IDentifier for wireless stations.
+
+ BSS
+ IEEE 802.11 Basic Service Set.
+
+ CCMP
+ Code Mode/CBC Mac Protocol
+
+ CEPT
+ European Conference of Postal and
+ Telecommunications Administrations.
+
+ CRC
+ Cyclic Redundancy Check.
+
+ DSSS
+ Direct-Sequence Spread Spectrum.
+
+ EAP
+ Extensible Authentication Protocol.
+
+ ERP
+ Extended Rate PHY
+
+ FHSS
+ Frequency-Hopping Spread Spectrum.
+
+ IAPP
+ Inter-Access-Point Protocol.
+
+ ICV
+ Integrity Check Value.
+
+ ISM
+ Industrial, Scientific, and Medical.
+
+ MBSSID
+ Multiple Broadcast SSID
+
+ MIC
+ Message Integrity Check.
+
+ MMH
+ Multi-Modal Hashing.
+
+ OFDM
+ Orthogonal Frequency Division Multiplexing.
+
+ PHY
+ Physical Layer (Layer 1 in network model).
+
+ PLCP
+ Physical Layer Convergence Procedure.
+
+ PMD
+ Physical Medium Dependent.
+
+ PSPF
+ Public Secure Packet Forwarding.
+
+ RF
+ Radio Frequency.
+
+ SS
+ Spread-spectrum.
+
+ SSID
+ Radio Service Set ID.
+
+ STA
+ IEEE 802.11 wireless station.
+
+ U-NII
+ Unlicensed National information Infrastructure
+
+ VLAN
+ Virtual LAN.
+
+ WEP
+ Wired Equivalent Privacy.
+
+ WGB
+ Work-group Bridge
+
+ WPA
+ WiFi Protected Access
+
+ GLOSSARY
+
+ Access point
+ Transmitter/receiver (transceiver) device
+ that commonly connects and transports data
+ between a wireless network and a wired network.
+
+ Association
+ The service used to establish access point
+ or station mapping and enable STA invocation
+ of the distribution system services.
+ (Wireless clients attempt to connect to
+ access points.)
+
+ Basic Rate
+ A data rate that is mandatory for client
+ devices to support in order for them to achieve
+ successful association.
+
+ Basic Service Set
+ The IEEE 802.11 BSS of an AP comprises of the
+ stations directly associating with the AP.
+
+ Bridge
+ Device that connects two or more segments
+ and reduces traffic by analyzing the
+ destination address, filtering the frame,
+ and forwarding the frame to all connected
+ segments.
+
+ Bridge AP
+ It is an AP that functions as a transparent
+ bridge between 2 wired LAN segments.
+
+ Broadcast SSID
+ Clients can send out Broadcast SSID Probe
+ Requests to a nearby AP, and the AP will
+ broadcast its own SSID within its beacons
+ to response to the clients. Clients can use
+ this Broadcast SSID to associate and
+ communicate with the AP.
+
+ Cyclic Redundancy Check
+ CRC is an error detect mechanism that applies
+ to frame transmission.
+
+ Direct-Sequence Spread Spectrum
+ DSSS combines a data signal at the sending
+ station with a higher data rate bit sequence,
+ which many refer to as a chipping code (also
+ known as processing gain). A high processing gain
+ increases the signals resistance to interference.
+ DSSS sends a specific string of bits for each data
+ bit sent.
+
+ ERP-CCK Modulation
+ This signal modulation technique is supported in
+ PHY implementing IEEE 802.11b/g Protocol.
+
+ ERP-OFDM Modulation
+ This signal modulation technique is supported in
+ PHY implementing IEEE 802.11g Protocol.
+
+ Extensible Authentication Protocol
+ EAP acts as the interface between a wireless
+ client and an authentication server, such as a
+ RADIUS server, to which the access point
+ communicates over the wired network.
+
+ Extended Rate PHY
+ This PHY implements the IEEE 802.11g Protocol.
+
+ Frequency-Hopping Spread Spectrum
+ In FHSS, a hopping code determines the frequencies
+ the radio will transmit and in which order. To
+ properly receive the signal, the receiver must be
+ set to same hopping code and listen to the
+ incoming signal at the right time and correct
+ frequency. The code pattern maintains a single
+ logical channel.
+
+ IEEE 802.11
+ Standard to encourage interoperability among
+ wireless networking equipment.
+
+ IEEE 802.11b
+ High-rate wireless LAN standard for wireless
+ data transfer at up to 11 Mbps.
+
+ IEEE P802.11g
+ Higher Speed Physical Layer (PHY) Extension to
+ IEEE 802.11b, will boost wireless LAN speed to 54
+ Mbps by using OFDM (orthogonal frequency division
+ multiplexing). The IEEE 802.11g specification is
+ backward compatible with the widely deployed IEEE
+ 802.11b standard.
+
+ Inter-Access-Point Protocol
+ The IEEE 802.11 standard does not define how
+ access points track moving users or how to
+ negotiate a handoff from one access point to the
+ next, a process referred to as roaming. IAPP is
+ a Cisco proprietary protocol to support roaming.
+ However, IAPP does not address how the wireless
+ system tracks users moving from one subnet to
+ another.
+
+ Independent network
+ Network that provides peer-to-peer connectivity
+ without relying on a complete network
+ infrastructure.
+
+ Integrity Check Value
+ The WEP ICV shall be a 32-bit value containing
+ the 32-bit cyclic redundancy code designed for
+ verifying wireless data frame integrity.
+
+ Message Integrity Check
+ A MIC can, optionally, be added to WEP-encrypted
+ 802.11 frames. MIC prevents attacks on encrypted
+ packets. MIC, implemented on both the access point
+ and all associated client devices, adds a few bytes
+ to each packet to make the packets tamper-proof.
+
+ Native VLAN ID
+ A switch port and/or AP can be configured with a
+ 'native VLAN ID'. Untagged or priority-tagged
+ frames are implicitly associated with the native
+ VLAN ID. The default native VLAN ID is '1' if
+ VLAN tagging is enabled. The native VLAN ID is '0'
+ or 'no VLAN ID' if VLAN tagging is not enabled.
+
+ Node
+ Device on a network; has its own unique network
+ address and name.
+
+ Non-Root Bridge
+ This wireless bridge does not connect to the main
+ wired LAN segment. It connects to a remote wired
+ LAN segment and can associate with root bridges and
+ other non-root bridges that accept client
+ associations. It also can accept associations from
+ other non-root bridges, repeater access points,
+ and client devices.
+
+ Physical Layer Convergence Procedure
+ In IEEE 802.11 wireless LANs, PLCP defines a method
+ of mapping the IEEE 802.11 MAC sublayer protocol
+ data units into a framing format suitable for
+ sending and receiving user data and management
+ information between two or more wireless stations
+ using the associated PMD system.
+
+ Physical Medium Dependent
+ In IEEE 802.11 wireless LANs, a PMD system, whose
+ function defines the characteristics of, and method
+ of transmitting and receiving data through, a
+ wireless medium between two or more wireless
+ stations each using the DSSS.
+
+ Preamble
+ The radio preamble are data at the head of a
+ packet that contains information access points
+ and client devices required by IEEE 802.11 when
+ sending and receiving packets.
+
+ Primary LAN
+ In an AP, if the destinations of inbound unicast
+ frames are unknown, the frames are sent toward
+ the primary LAN defined on the device.
+
+ Radio carrier
+ Radio waves that deliver energy to a remote
+ receiver; in other words, radio waves in a
+ wireless LAN environment.
+
+ Repeater
+ Device that connects multiple segments,
+ listening to each and regenerating the signal
+ on one to every other connected one; so that
+ the signal can travel further.
+
+ Repeater or Non-root Access Point
+ The repeater access point is not connected
+ to the wired LAN. The Repeater is a wireless
+ LAN transceiver that transfers data between
+ a client and another access point, another
+ repeater, or between two bridges. The repeater
+ is placed within radio range of an access point
+ connected to the wired LAN, another repeater, or
+ an non-root bridge to extend the range of the
+ infrastructure.
+
+ Radio Frequency
+ Radio wave and modulation process or operation.
+
+ Root Access Point
+ This access point connects clients to the main
+ wired LAN.
+
+ Root (Wireless) Bridge
+ This wireless bridge connects to the main wired
+ LAN. It can communicate with non-root wireless
+ bridges, repeater access points, and client
+ devices but not with another wireless root
+ bridge. Only one wireless bridge in a wireless
+ LAN can be set as the wireless root bridge.
+
+ Spread-spectrum
+ Wideband radio frequency technique that
+ consumes more bandwidth than the narrow-band
+ alternative but produces a signal that is louder
+ and easier to detect. There are two types of
+ spread-spectrum radio: frequency hopping and
+ direct sequence.
+
+ Radio Service Set ID
+ SSID is a unique identifier that APs and clients
+ use to identify with each other. SSID is a simple
+ means of access control and is not for security.
+ The SSID can be any alphanumeric entry up to 32
+ characters.
+
+ Tag header
+ A 'tag header' is as defined in the IEEE 802.1Q
+ standard. An 802.1Q tag header contains a 3-bit
+ priority field and a 12-bit VLAN ID field.
+ A 'priority tag' has a VLAN ID of 0, to indicate
+ 'no VLAN ID'. A 'VLAN tag' has a non-zero
+ VLAN ID.
+
+ Virtual LAN
+ VLAN defined in the IEEE 802.1Q VLAN standard
+ supports logically segmenting of LAN
+ infrastructure into different subnets or
+ workgroups so that packets are switched only
+ between ports within the same VLAN.
+
+ VLAN ID
+ Each VLAN is identified by a 12-bit 'VLAN ID'.
+ A VLAN ID of '0' is used to indicate
+ 'no VLAN ID'. Valid VLAN IDs range from '1' to
+ '4095'. VLAN of ID '4095' is the default VLAN
+ for Cisco VoIP Phones.
+
+ Wired Equivalent Privacy
+ WEP is generally used to refer to 802.11
+ encryption.
+
+ Work-group Bridge
+ It is a client to APs or wireless root bridges.
+ The radio port of a WGB serves as the uplink to
+ the main network and the Ethernet port provides
+ network access for devices like PC or IP phone.
+
+ Upgrade of Frequencies
+ As per the latest regulations proposed by the
+ Japanese Government, the four channels 34
+ ( 5170 GHz ), 38 ( 5190 GHz), 42 ( 5210 ) and
+ 44 ( 5230 ) in the 5150-5250 MHz band has been
+ shifted by 10 MHz. Thus, the new channels in the
+ 5150-5250 MHz band are 36 ( 5180 ), 40 ( 5200 )
+ and 44 ( 5220 ) and 48 ( 5240 )."
+
+ REVISION "200612200000Z"
+ DESCRIPTION
+ "- Added following objects in cd11IfStationConfigTable
+ cd11IfMobileStationListIgnore
+ cd11IfMobileStationScanChannel.
+ - Added cd11Ifdot11MobileStationScanGroup OBJECT-GROUP
+ - Added ciscoDot11IfComplianceRev4 MODULE-COMPLIANCE."
+ REVISION "200503100000Z"
+ DESCRIPTION
+ "Updated the cd11IfCurrentCarrierSet to define new
+ carrier types."
+ REVISION "200406060000Z"
+ DESCRIPTION
+ "Modified the cd11IfPhyNativePowerUseStandard to
+ read-write and updated cd11IfNativeTxPowerSupportTable
+ and cd11IfRfNativePowerTable to add the object
+ cd11IfRadioModulationClass as indices."
+ REVISION "200405060000Z"
+ DESCRIPTION
+ "Added cd11IfStationSwitchOverNotif and
+ cd11IfRogueApDetectedNotif notifications"
+ REVISION "200404170000Z"
+ DESCRIPTION
+ "Added cd11IfVlanPsPacketForwardEnable and
+ cd11IfPsPacketForwardEnable for PSPF support.
+ Added cd11IfMultipleBssidEnable for MBSSID support.
+ Modified Cd11IfVlanEncryptKeyEntry to add objects
+ for WEP encryption support. Added
+ cd11IfRogueApDetectedTable for rogue AP detection
+ information. Added cd11IfFrequencyBandTable,
+ cd11IfRfNativePowerTable, and
+ cd11IfNativeTxPowerSupportTable to support per
+ radio frequency band power configuration. Added
+ cd11IfDataRatesSensitivityTable for receive
+ sensitivity specifications of IEEE 802.11 radio."
+ REVISION "200402270000Z"
+ DESCRIPTION
+ "Updated the cd11IfStationRole object description.
+ Modified CDot11IfCipherType textual convention to
+ match the latest design. Updated
+ cd11IfClientTxPowerTable power levels to allow
+ negative dBm power. Modified the
+ MODULE-COMPLIANCE for this MIB."
+ REVISION "200311170000Z"
+ DESCRIPTION
+ "Added cd11IfWorldModeCountry, cd11IfWorldMode, and
+ cd11IfMobileStationScanParent to
+ cd11IfStationConfigEntry. Added cd11IfPhyConcatenation
+ to cd11IfPhyOperationEntry. Added
+ cd11IfVlanEncryptKeyTransmit to
+ Cd11IfVlanEncryptKeyEntry. Added
+ cd11IfClientTxPowerTable, cd11IfOfdmTxPowerTable,
+ cd11IfRadioMonitoringTable, and
+ cd11IfVlanSecurityTable. Modified the
+ MODULE-COMPLIANCE for this MIB."
+ REVISION "200307130000Z"
+ DESCRIPTION
+ "Added cd11IfPhyBasicRateSet to identify if a rate
+ in the dot11OperationalRateSet is a Basic Rate, added
+ cd11IfPhyMacSpecification to identify the IEEE 802.11
+ Standard being applied to the radio, modified the
+ cd11IfPhyDsssCurrentChannel and cd11IfChanSelectChannel
+ ranges to support 802.11A radio, and added new device
+ types to cd11IfStationRole.
+
+ Added cd11IfAuxSsidAuthAlgEapMethod,
+ cd11IfAuxSsidAuthAlgMacMethod, cd11IfAuthAlgEapMethod,
+ and cd11IfAuthAlgMacAddrMethod to specify the
+ authentication method list."
+ REVISION "200212290000Z"
+ DESCRIPTION
+ "Added a new cd11IfVlanEncryptKeyTable to support
+ per interface and VLAN encryption key and
+ cd11IfDomainCapabilitySet to support the
+ IEEE 802.11 dot11MultiDomainCapabilityTable."
+ REVISION "200208010000Z"
+ DESCRIPTION
+ "Corrected the description of roleBridge(2) of
+ the cd11IfStationRole object and changed the roleAP(1)
+ to roleWgb(1)."
+ REVISION "200207040000Z"
+ DESCRIPTION
+ "Changed cd11IfAuxSsidBroadcastSsid from read-only
+ to read-write."
+ REVISION "200205100000Z"
+ DESCRIPTION
+ "The maximum value for cd11IfAuxiliarySsidLength is
+ changed to '4095'. The new cd11IfAuxSsidIndex replaces
+ cd11IfAuxSsid as the cd11IfAuxSsidTable index. New
+ enumerate values are added to cd11IfStationRole. New
+ MAC address authentication cd11IfAuthAlgRequireMacAddr
+ and cd11IfAuxSsidAuthAlgRequireMac objects are added to
+ the authentication algorithm tables."
+ REVISION "200204110000Z"
+ DESCRIPTION
+ "This is the initial version of this MIB module."
+ ::= { ciscoMgmt 272 }
+
+
+ciscoDot11IfMIBNotifications OBJECT IDENTIFIER
+ ::= { ciscoDot11IfMIB 0 }
+
+ciscoDot11IfMIBObjects OBJECT IDENTIFIER
+ ::= { ciscoDot11IfMIB 1 }
+
+cd11IfConfigurations OBJECT IDENTIFIER
+ ::= { ciscoDot11IfMIBObjects 1 }
+
+cd11IfStatistics OBJECT IDENTIFIER
+ ::= { ciscoDot11IfMIBObjects 2 }
+
+cd11IfManagement OBJECT IDENTIFIER
+ ::= { cd11IfConfigurations 1 }
+
+cd11IfPhyConfig OBJECT IDENTIFIER
+ ::= { cd11IfConfigurations 2 }
+
+cd11IfMacStatistics OBJECT IDENTIFIER
+ ::= { cd11IfStatistics 1 }
+
+
+-- Textual Conventions
+
+CDot11IfVlanIdOrZero ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "This is a 12-bit VLAN ID used in the VLAN Tag
+ header. A value of '0' indicates NULL or no VLAN ID.
+ and '4095' is the default VLAN for Cisco VoIP Phones.
+ This textual convention differs from the VlanId
+ textual convention, defined by the Q-BRIDGE-MIB
+ in RFC-2674, because VlanId does not permit the
+ value '0' and '4095'."
+ REFERENCE
+ "RFC-2674, Bridge MIB Extensions, August 1999,
+ Q-BRIDGE-MIB, E. Bell."
+ SYNTAX Unsigned32 (0..4095)
+
+
+WepKeyType128 ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "WEP shared secret encryption key, 128-bits or 16
+ octets. Only the first 13 octets are accessible to
+ users among the total 16 octets."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, Section 8.3.2."
+ SYNTAX OCTET STRING (SIZE (5..13))
+
+
+CDot11IfMicAlgorithm ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Auxiliary MIC calculated on WEP-encoded packets
+ to validate that they have not been modified.
+ This is in addition to the standard 802.11 ICV.
+ The two options are:
+ micNone(1) - do not apply MIC,
+ micMXX(2) - apply MMH MIC,
+ micMichael(3) - Michael MIC."
+ SYNTAX INTEGER {
+ micNone(1),
+ micMXX(2),
+ micMichael(3)
+ }
+
+
+CDot11IfWepKeyPermuteAlgorithm ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "This defines the function through which the WEP
+ encryption key is permuted between key renewal
+ periods.
+ wepPermuteNone(1) - no WEP key permutation,
+ wepPermuteIV(2) - WEP key permutation with
+ initialization vector."
+ SYNTAX INTEGER {
+ wepPermuteNone(1),
+ wepPermuteIV(2)
+ }
+
+
+CDot11IfCipherType ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "These are the frame encryption cipher types for
+ frames on IEEE 802.11 radio interfaces.
+ ckip Cisco Per packet key hashing,
+ cmic Cisco MMH MIC,
+ tkip WPA Temporal Key encryption,
+ wep40 40-bit WEP key,
+ wep128 128-bit WEP key,
+ aesccm WPA AES CCMP encryption."
+ SYNTAX BITS {
+ ckip(0),
+ cmic(1),
+ tkip(2),
+ wep40(3),
+ wep128(4),
+ aesccm(5)
+ }
+
+
+CDot11RadioFrequencyBandType ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "These are the radio frequency band names
+ the IEEE 802.11 radio is operating on:
+ ism24G(0) - ISM 2.4 GHz band,
+ unii1(1) - U-NII-1 band (5.15-5.25 GHz),
+ unii2(2) - U-NII-2 band (5.25-5.35 GHz),
+ unii3(3) - U-NII-3 band (5.725-5.825 GHz),
+ cept(4) - CEPT band B (5.47-5.725 GHz),
+ japan49G(5) - Japan 4.9 band (4.9-5.0 GHz),
+ japan50G(6) - Japan 5.0 band (5.03-5.091 GHz)."
+ SYNTAX BITS {
+ ism24G(0),
+ unii1(1),
+ unii2(2),
+ unii3(3),
+ cept(4),
+ japan49G(5),
+ japan50G(6)
+ }
+
+CDot11RadioModulationClass ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "These are classifications of radio modulation
+ techniques used by the various Physical Layers
+ of IEEE 802.11 radios:
+ dsss(1) - modulation schemes associated
+ with DSSS type PHYs,
+ ofdm(2) - modulation schemes associated
+ with OFDM type PHYs."
+ SYNTAX INTEGER {
+ dsss(1),
+ ofdm(2)
+ }
+
+Cd11IfDot11UpgradeStatus ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "These are the various status on the
+ Radio Upgrade:
+ unknown(1) - upgrade status unknown,
+ upgradeNotApplicable(2) - Regulatory domain upgrade
+ is not applicable for 11b/g
+ radios and 11a radios not in
+ Japan regulatory domain,
+ upgradeNotDone(3) - 11a radio is in Japan domain but
+ yet to be upgraded,
+ upgradeNotNeeded(4) - 11a radio is already configured to
+ operate in the W52 domain and that
+ the upgrade is not needed,
+ upgradeDone(5) - upgrade has been done from J52 to W52."
+ SYNTAX INTEGER {
+ unknown(1),
+ upgradeNotApplicable(2),
+ upgradeNotDone(3),
+ upgradeNotNeeded(4),
+ upgradeDone(5)
+ }
+
+-- ********************************************************************
+-- * Cisco IEEE 802.11 Interface Extension
+-- ********************************************************************
+
+-- Configuration Objects
+
+cd11IfStationConfigTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfStationConfigEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table contains attributes to configure radio
+ interfaces managed by this agent. The attributes
+ are extensions to the configuration parameters in
+ the dot11StationConfigTable defined in the
+ IEEE802dot11-MIB. This table configures the station
+ role of the interface, proprietary extensions,
+ hierarchy, security option and parameters, and
+ communication settings. This table has a sparse
+ dependent relationship on the ifTable.
+ For each entry in this table, there exists an entry
+ in the ifTable of ifType ieee80211(71).
+ Entries in this table cannot be created or deleted
+ by the network management system. All entries are
+ created or deleted by the agent."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfManagement 1 }
+
+cd11IfStationConfigEntry OBJECT-TYPE
+ SYNTAX Cd11IfStationConfigEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A collection of configuration attributes for
+ an IEEE 802.11 radio interface. These attributes
+ are supplements to attributes defined in the
+ dot11StationConfigTable in IEEE802dot11-MIB."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ INDEX { ifIndex }
+ ::= { cd11IfStationConfigTable 1 }
+
+Cd11IfStationConfigEntry ::=
+ SEQUENCE {
+ cd11IfStationRole INTEGER,
+ cd11IfCiscoExtensionsEnable TruthValue,
+ cd11IfAllowBroadcastSsidAssoc TruthValue,
+ cd11IfPrivacyOptionMaxRate Integer32,
+ cd11IfEthernetEncapsulDefault INTEGER,
+ cd11IfBridgeSpacing Unsigned32,
+ cd11IfDesiredSsidMaxAssocSta Unsigned32,
+ cd11IfAuxiliarySsidLength Unsigned32,
+ cd11IfVoipExtensionsEnable TruthValue,
+ cd11IfDesiredSsidMicAlgorithm CDot11IfMicAlgorithm,
+ cd11IfDesiredSsidWepPermuteAlg
+ CDot11IfWepKeyPermuteAlgorithm,
+ cd11IfWorldMode INTEGER,
+ cd11IfWorldModeCountry OCTET STRING,
+ cd11IfMobileStationScanParent TruthValue,
+ cd11IfPsPacketForwardEnable TruthValue,
+ cd11IfMultipleBssidEnable TruthValue,
+ cd11IfMobileStationListIgnore TruthValue,
+ cd11IfMobileStationScanChannel OCTET STRING
+ }
+
+cd11IfStationRole OBJECT-TYPE
+ SYNTAX INTEGER {
+ roleWgb(1),
+ roleBridge(2),
+ roleClient(3),
+ roleRoot(4),
+ roleRepeater(5),
+ roleApBridge(6),
+ roleApRepeater(7),
+ roleIBSS(8),
+ roleNrBridge(9),
+ roleApNrBridge(10),
+ roleScanner(11)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This defines the role of this station itself within
+ the 802.11 BSS of which it is a member. The roles are:
+ roleWgb(1) - infrastructure type WGB
+ client,
+ roleBridge(2) - root bridge,
+ roleClient(3) - independent BBS type
+ WGB client,
+ roleRoot(4) - root access point,
+ roleRepeater(5) - repeater,
+ roleApBridge(6) - AP and root bridge,
+ roleApRepeater(7) - AP and repeater,
+ roleIBSS(8) - independent BSS,
+ roleNrBridge(9) - non-root bridge,
+ roleApNrBridge(10) - AP and non-root bridge,
+ roleScanner(11) - scanner for rogue APs
+ and clients.
+ The default role is roleRoot(4)."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 3."
+ ::= { cd11IfStationConfigEntry 1 }
+
+cd11IfCiscoExtensionsEnable OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "Cisco Aironet extensions to the basic IEEE
+ 802.11 protocols are enabled if the value is
+ 'true'. The extension enables better BSS
+ performance and faster roaming. If the value
+ is 'false', only the basic IEEE 802.11 protocols
+ are used. This ensures maximum compatibility
+ with non-Cisco equipment. The default value is
+ 'true'."
+ ::= { cd11IfStationConfigEntry 2 }
+
+cd11IfAllowBroadcastSsidAssoc OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If the value of cd11IfStationRole is either
+ 'roleRoot' or 'roleRepeater', and if
+ cd11IfAllowBroadcastSsidAssoc is 'true',
+ the device radio driver will respond
+ to Broadcast SSID Probe Requests and will
+ broadcast its own SSID within its beacons.
+ If cd11IfAllowBroadcastSsidAssoc is 'false',
+ the radio will not respond to the Broadcast
+ SSID and will not broadcast its SSID within
+ beacons. The default value is 'true'."
+ ::= { cd11IfStationConfigEntry 3 }
+
+cd11IfPrivacyOptionMaxRate OBJECT-TYPE
+ SYNTAX Integer32 (2..127)
+ UNITS "500 Kb per second"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object specifies the maximum transmit bit
+ rate supported by the radio when using, for example,
+ WEP encryption. The rate is expressed in standard
+ IEEE 802.11 increments of 500Kb/sec."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 8.1.2."
+ ::= { cd11IfStationConfigEntry 4 }
+
+cd11IfEthernetEncapsulDefault OBJECT-TYPE
+ SYNTAX INTEGER {
+ encap802dot1H(1),
+ encapRfc1042(2)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object specifies the Ethernet encapsulation
+ transform type used within the BSS. The encapsulations
+ allowed are either IEEE 802.1H type or RFC-1042 type.
+ IEEE 802.1H designates the Subnetwork Access Protocol
+ (SNAP) mechanism as the Ethernet encapsulation protocol.
+ Subsequently, other (non-IP) uses of the RFC-1042
+ mechanism. RFC-1042 specifies a translation for
+ Ethernet frames, such that they can be exchanged with
+ end stations on LANs that do not provide an Ethernet
+ service.
+ encap802dot1H(1) - IEEE 802.1H SNAP encapsulation
+ encapRfc1042(2) - RFC-1042 encapsulation.
+ The default encapsulation type is encap802dot1H(1)."
+ REFERENCE
+ "IEEE Std 802.1H-1997, Media Access Control
+ Bridging of Ethernet V2.0 in Local Area
+ Networks. RFC-1042, February 1988, A Standard for
+ the Transmission of IP Datagrams over IEEE 802
+ Networks, J. Postel and J. Reynolds."
+ ::= { cd11IfStationConfigEntry 5 }
+
+cd11IfBridgeSpacing OBJECT-TYPE
+ SYNTAX Unsigned32 (0..38640)
+ UNITS "Kilometers"
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If this device is a root wireless bridge,
+ this value is the distance in kilometers
+ reported between this device and its
+ farthest non-root bridge client."
+ ::= { cd11IfStationConfigEntry 6 }
+
+cd11IfDesiredSsidMaxAssocSta OBJECT-TYPE
+ SYNTAX Unsigned32 (0..2007)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object defines the maximum number of IEEE
+ 802.11 stations which may associate with this radio
+ interface through IEEE802dot11-MIB dot11DesiredSSID.
+ If this value is '0', the maximum number is limited
+ only by the IEEE 802.11 standard and any hardware or
+ radio firmware limitations of the access point. The
+ default value is '0'."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 5.7."
+ ::= { cd11IfStationConfigEntry 7 }
+
+cd11IfAuxiliarySsidLength OBJECT-TYPE
+ SYNTAX Unsigned32 (0..4095)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object specifies the maximum number of SSIDs
+ allowed for a radio interface or the number of SSID
+ entries per radio interface in the cd11IfAuxSsidTable.
+ The default value is '25'."
+ ::= { cd11IfStationConfigEntry 8 }
+
+cd11IfVoipExtensionsEnable OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object enables the radio generate proprietary
+ elements in its beacons and probe responses to support
+ Voice-over-IP (VoIP) phones. The default value is
+ 'true'."
+ ::= { cd11IfStationConfigEntry 9 }
+
+cd11IfDesiredSsidMicAlgorithm OBJECT-TYPE
+ SYNTAX CDot11IfMicAlgorithm
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object defines the auxiliary MIC calculated
+ on WEP-encoded packets of stations associated with
+ this radio interface through IEEE802dot11-MIB
+ dot11DesiredSSID. The default value is micNone(1)."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 8.2.3."
+ ::= { cd11IfStationConfigEntry 10 }
+
+cd11IfDesiredSsidWepPermuteAlg OBJECT-TYPE
+ SYNTAX CDot11IfWepKeyPermuteAlgorithm
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object defines the function through which
+ the WEP encryption key is permuted between key
+ renewal periods for stations associated with this
+ radio interface through IEEE802dot11-MIB
+ dot11DesiredSSID. The default value is
+ wepPermuteNone(1)."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 8.2.3."
+ ::= { cd11IfStationConfigEntry 11 }
+
+cd11IfWorldMode OBJECT-TYPE
+ SYNTAX INTEGER {
+ none(1),
+ legacy(2),
+ dot11d(3)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object sets the World-Mode function of the
+ radio to allow it to function in countries other
+ than it was manufactured for.
+ none(1) - No world mode setting,
+ legacy(2) - compatible with legacy hardware,
+ dot11d(3) - use IEEE 802.11d mechanism."
+ DEFVAL { none }
+ ::= { cd11IfStationConfigEntry 12 }
+
+cd11IfWorldModeCountry OBJECT-TYPE
+ SYNTAX OCTET STRING (SIZE(3))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object sets the dot11CountryString in the
+ IEEE802dot11-MIB identifying the country in which
+ the radio is operating. When cd11IfWorldMode is
+ either legacy(2) or dot11d(3), this object value
+ will be sent in the radio management frame.
+
+ The first two octets of this string is the two
+ character country code as described in document
+ ISO/IEC 3166-1. The third octet shall be one of
+ the following:
+
+ 1. an ASCII space character, if the regulations under
+ which the station is operating encompass all
+ environments in the country,
+
+ 2. an ASCII 'O' character, if the regulations under
+ which the station is operating are for an Outdoor
+ environment only, or
+
+ 3. an ASCII 'I' character, if the regulations under
+ which the station is operating are for an Indoor
+ environment only."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfStationConfigEntry 13 }
+
+cd11IfMobileStationScanParent OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object enables the radio to scan for a better
+ parent when it is a mobile non-root device, for
+ example, the value of cd11IfStationRole is roleWgb(1)."
+ DEFVAL { false }
+ ::= { cd11IfStationConfigEntry 14 }
+
+cd11IfPsPacketForwardEnable OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If no VLAN is configured on the radio interface,
+ this object configures the PSPF feature. Otherwise,
+ cd11IfVlanPsPacketForwardEnable is used to configure
+ the PSPF feature per VLAN. If it is 'true', PSPF is
+ on the radio interface and direct traffic between
+ wireless clients of the interface is not allowed.
+ If it is 'false', PSPF is disabled on the VLAN and
+ direct traffic between wireless clients of the
+ interface is allowed."
+ DEFVAL { false }
+ ::= { cd11IfStationConfigEntry 15 }
+
+cd11IfMultipleBssidEnable OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If it is 'true', multiple broadcast SSID is
+ enabled on the radio. To a wireless client, a
+ MBSSID AP appears to be several distinct co-located
+ APs, and it transmits a beacon for each broadcast
+ SSID or SSID. This allows all of the SSIDs visible
+ for passive scanning."
+ DEFVAL { false }
+ ::= { cd11IfStationConfigEntry 16 }
+
+cd11IfMobileStationListIgnore OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object indicates whether the radio should
+ process the AP adjacency and Enhanced Neighbor
+ List reports specified in the CCX Specification.
+ AP adjacency and Enhanced Neighbor List provide
+ information about the infrastructure wireless
+ devices found in the near vicinity of this
+ radio.
+
+ This object is applicable only when the radio's
+ role as represented by the object cd11IfStationRole
+ is one of roleWgb(1), roleRepeater(5) or
+ roleNrbridge(9).
+
+ Agent will populate a value of 'false', when the
+ radio's role as represented by cd11IfStationRole
+ is one of roleRoot(4) ,roleBridge(2) or
+ roleApBridge(6), to indicate that the object is
+ not applicable for the radio in these roles. Set
+ requests will be rejected when the radio is
+ configured to be in one of these roles.
+
+ User can configure this object only when
+ cd11IfMobileStationScanChannel is configured with
+ a valid set of channels. When
+ cd11IfMobileStationScanChannel is configured with
+ a value of 0, the agent will automatically
+ populate a value of 'false'. "
+ DEFVAL { false }
+ ::= { cd11IfStationConfigEntry 17 }
+
+cd11IfMobileStationScanChannel OBJECT-TYPE
+ SYNTAX OCTET STRING (SIZE(1..64))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object specifies the channels to be used by
+ the infractructure clients for scanning purposes.
+
+ This object is applicable only when the radio's
+ role as represented by the object cd11IfStationRole
+ is one of roleWgb(1), roleRepeater(5) or
+ roleNrbridge(9). Agent will reject the request
+ to set this object when the cd11IfStationRole doesn't
+ populate one of the values mentioned above.
+
+ Each octet carries the channel number. To configure
+ the radio to scan all the channels applicable to a
+ particular regulatory domain, this object should be
+ configured with only one octet of value 0. "
+ ::= { cd11IfStationConfigEntry 18 }
+
+
+cd11IfAuthAlgorithmTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfAuthAlgorithmEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table contains attributes to configure
+ authentication algorithm parameters for associations
+ through the SSID defined by IEEE802dot11-MIB
+ dot11DesiredSSID object. It defines attributes
+ additional to those defined in the IEEE802dot11-MIB
+ dot11AuthenticationAlgorithmsTable. An interface
+ may support multiple authentication algorithms.
+
+ This table has an expansion dependent relationship
+ on the ifTable. For each entry in this table,
+ there exists at least an entry in the ifTable of
+ ifType ieee80211(71). This table uses the
+ dot11AuthenticationAlgorithmsIndex of the
+ dot11AuthenticationAlgorithmsTable defined in the
+ IEEE802dot11-MIB as the expansion index.
+
+ Entries in this table cannot be created or deleted
+ by the network management system. All entries are
+ created or deleted by the agent."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 5.7.6 and IEEE802dot11-MIB."
+ ::= { cd11IfManagement 2 }
+
+cd11IfAuthAlgorithmEntry OBJECT-TYPE
+ SYNTAX Cd11IfAuthAlgorithmEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry specifies authentication algorithm
+ configuration attributes of a VLAN for the
+ dot11DesiredSSID on a radio interface."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 8.2 and IEEE802dot11-MIB."
+ INDEX {
+ ifIndex,
+ dot11AuthenticationAlgorithmsIndex
+ }
+ ::= { cd11IfAuthAlgorithmTable 1 }
+
+Cd11IfAuthAlgorithmEntry ::=
+ SEQUENCE {
+ cd11IfAuthAlgRequireEap TruthValue,
+ cd11IfAuthAlgRequireMacAddr TruthValue,
+ cd11IfAuthAlgDefaultVlan CDot11IfVlanIdOrZero,
+ cd11IfAuthAlgEapMethod SnmpAdminString,
+ cd11IfAuthAlgMacAddrMethod SnmpAdminString
+ }
+
+cd11IfAuthAlgRequireEap OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If the value is 'true', stations authenticating
+ with the corresponding IEEE802dot11-MIB
+ dot11AuthenticationAlgorithm must complete
+ network-level EAP authentication before their
+ association attempts will be unblocked. If the
+ value is 'false', stations authenticating with
+ the corresponding dot11AuthenticationAlgorithm
+ will be unblocked as soon as they complete the
+ 802.11 authentication. The default value is
+ 'true'."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 8.2 and IEEE802dot11-MIB."
+ ::= { cd11IfAuthAlgorithmEntry 1 }
+
+cd11IfAuthAlgRequireMacAddr OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If the value is 'true', stations authenticating
+ with the corresponding IEEE802dot11-MIB
+ dot11AuthenticationAlgorithm must complete
+ additional MAC address authentication before their
+ association attempts will be unblocked. If the
+ value is 'false', stations authenticating with
+ the corresponding dot11AuthenticationAlgorithm
+ will be unblocked as soon as they complete the
+ 802.11 authentication. The default value is
+ 'true'."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 8.2 and IEEE802dot11-MIB."
+ ::= { cd11IfAuthAlgorithmEntry 2 }
+
+cd11IfAuthAlgDefaultVlan OBJECT-TYPE
+ SYNTAX CDot11IfVlanIdOrZero
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object defines the default VLAN identifier
+ for stations associated with this radio interface
+ with this authentication and through
+ IEEE802dot11-MIB dot11DesiredSSID. If the value
+ of this object is '0', it indicates that either the
+ default VLAN are not defined for this authentication
+ on this radio interface or the default VLAN is the
+ native VLAN ID. The default value is '0'."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 8.2 and IEEE802dot11-MIB."
+ ::= { cd11IfAuthAlgorithmEntry 3 }
+
+cd11IfAuthAlgEapMethod OBJECT-TYPE
+ SYNTAX SnmpAdminString
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If the value of cd11IfAuthAlgRequireEap is 'true'
+ or dot11AuthenticationAlgorithm is Network-EAP,
+ this is the EAP method list to used for the EAP
+ authentication."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfAuthAlgorithmEntry 4 }
+
+cd11IfAuthAlgMacAddrMethod OBJECT-TYPE
+ SYNTAX SnmpAdminString
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If the value of cd11IfAuthAlgRequireMacAddr
+ is 'true', this is the MAC address method list to
+ used for the MAC authentication."
+ ::= { cd11IfAuthAlgorithmEntry 5 }
+
+
+cd11IfWepDefaultKeysTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfWepDefaultKeysEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "The dot11WEPDefaultKeysTable defined by the
+ IEEE802dot11-MIB allows only WEP keys of length
+ up to 40 bits. This table overrides the the
+ dot11WEPDefaultKeysTable and supports keys of
+ from 40 to 128 bits. A maximum of four keys can
+ associate with any IEEE 802.11 radio interface.
+ For devices implementing this table, they should
+ not implement the dot11WEPDefaultKeysTable.
+
+ This table has an expansion dependent relationship
+ on the ifTable. For each entry in this table,
+ there exists at least an entry in the ifTable of
+ ifType ieee80211(71). Entries in this table
+ cannot be created or deleted by the network
+ management system. All entries are created or
+ deleted by the agent."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfManagement 3 }
+
+cd11IfWepDefaultKeysEntry OBJECT-TYPE
+ SYNTAX Cd11IfWepDefaultKeysEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A collection of attributes defining a WEP key for
+ a radio interface."
+ INDEX {
+ ifIndex,
+ cd11IfWepDefaultKeyIndex
+ }
+ ::= { cd11IfWepDefaultKeysTable 1 }
+
+Cd11IfWepDefaultKeysEntry ::=
+ SEQUENCE {
+ cd11IfWepDefaultKeyIndex Unsigned32,
+ cd11IfWepDefaultKeyLen Unsigned32,
+ cd11IfWepDefaultKeyValue WepKeyType128
+ }
+
+cd11IfWepDefaultKeyIndex OBJECT-TYPE
+ SYNTAX Unsigned32 (1..4)
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This object identifies a WEP key instance for
+ a radio interface."
+ ::= { cd11IfWepDefaultKeysEntry 1 }
+
+cd11IfWepDefaultKeyLen OBJECT-TYPE
+ SYNTAX Unsigned32 (5..13)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object specifies the length in octets of
+ the WEP key cd11IfWepDefaultKeyValue. The
+ default key length is '13'."
+ ::= { cd11IfWepDefaultKeysEntry 2 }
+
+cd11IfWepDefaultKeyValue OBJECT-TYPE
+ SYNTAX WepKeyType128
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This is the WEP default secret key value. Any
+ attempt to read this object by the NMS will
+ result in return of a zero-length string. The
+ default value is a NULL string."
+ ::= { cd11IfWepDefaultKeysEntry 3 }
+
+
+cd11IfDesiredBssTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfDesiredBssEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "When the radio is not functioning as an access
+ point (i.e., cd11IfStationRole is not 'roleRoot'),
+ and for example, this radio is a repeater or
+ bridge, this table will contain a list of preferred
+ access points with which the radio interface should
+ associate with. This table has an expansion
+ dependent relationship on the ifTable. For each
+ entry in this table, there exists at least an entry
+ in the ifTable of ifType ieee80211(71).
+ Entries in this table cannot be created or deleted
+ by the network management system. All entries are
+ created or deleted by the agent."
+ ::= { cd11IfManagement 5 }
+
+cd11IfDesiredBssEntry OBJECT-TYPE
+ SYNTAX Cd11IfDesiredBssEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry provides the MAC address of a preferred
+ access point. A maximum of 4 BSS addresses can be
+ configured to an interface."
+ INDEX {
+ ifIndex,
+ cd11IfDesiredBssIndex
+ }
+ ::= { cd11IfDesiredBssTable 1 }
+
+Cd11IfDesiredBssEntry ::=
+ SEQUENCE {
+ cd11IfDesiredBssIndex Unsigned32,
+ cd11IfDesiredBssAddr MacAddress
+ }
+
+cd11IfDesiredBssIndex OBJECT-TYPE
+ SYNTAX Unsigned32 (1..4)
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This object defines the priority order in which
+ preferred access points should be probed. Lower
+ index values indicate higher priority."
+ ::= { cd11IfDesiredBssEntry 1 }
+
+cd11IfDesiredBssAddr OBJECT-TYPE
+ SYNTAX MacAddress
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object defines the BSS identifier (MAC
+ address) of the access point with which the radio
+ should try to associate with. The value of this
+ object is '00:00:00:00:00:00' if the BSS
+ identifier for this priority is not specified
+ or configured. The default value is
+ '000000000000'H."
+ ::= { cd11IfDesiredBssEntry 2 }
+
+
+cd11IfAuxSsidTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfAuxSsidEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "When the radio is not functioning as a client
+ station (i.e., cd11IfStationRole is not
+ 'roleClient'), and for example, this is a access
+ point or independent BSS, this table will contain
+ a list of SSIDs which stations must be used to
+ associate with this radio. This table has an
+ expansion dependent relationship on the ifTable.
+ For each entry in this table, there exists at least
+ an entry in the ifTable of ifType ieee80211(71).
+ Entries in this table cannot be created or deleted
+ by the network management system. All entries are
+ created or deleted by the agent."
+ ::= { cd11IfManagement 6 }
+
+cd11IfAuxSsidEntry OBJECT-TYPE
+ SYNTAX Cd11IfAuxSsidEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A collection of attributes defining an auxiliary
+ service set which client stations can associate on
+ the specific interface. An interface can have
+ multiple auxiliary service sets while IEEE 802.11
+ defines only one desired service set for each
+ interface. Each radio interface currently supports
+ up to 25 SSIDs, and the cd11IfAuxiliarySsidLength
+ object specifies the configured maximum."
+ INDEX {
+ ifIndex,
+ cd11IfAuxSsidIndex
+ }
+ ::= { cd11IfAuxSsidTable 1 }
+
+Cd11IfAuxSsidEntry ::=
+ SEQUENCE {
+ cd11IfAuxSsidIndex Unsigned32,
+ cd11IfAuxSsid OCTET STRING,
+ cd11IfAuxSsidBroadcastSsid TruthValue,
+ cd11IfAuxSsidMaxAssocSta Unsigned32,
+ cd11IfAuxSsidMicAlgorithm CDot11IfMicAlgorithm,
+ cd11IfAuxSsidWepPermuteAlg
+ CDot11IfWepKeyPermuteAlgorithm
+ }
+
+cd11IfAuxSsidIndex OBJECT-TYPE
+ SYNTAX Unsigned32 (1..4095)
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This object identifies a SSID defined on a radio."
+ ::= { cd11IfAuxSsidEntry 1 }
+
+cd11IfAuxSsid OBJECT-TYPE
+ SYNTAX OCTET STRING (SIZE(0..32))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object specifies a SSID recognized by this
+ radio interface. The radio interface shall respond
+ to probe requests using this SSID, but it does not
+ advertise this SSID in its beacons."
+ ::= { cd11IfAuxSsidEntry 2 }
+
+cd11IfAuxSsidBroadcastSsid OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object indicates if an auxiliary SSID
+ is the Broadcast SSID. There is only one Broadcast
+ SSID per IEEE 802.11 radio interface."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 7.3.2.1."
+ ::= { cd11IfAuxSsidEntry 3 }
+
+cd11IfAuxSsidMaxAssocSta OBJECT-TYPE
+ SYNTAX Unsigned32 (0..2007)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object defines the maximum number of IEEE
+ 802.11 stations which may associate with this radio
+ interface through the cd11IfAuxSsid. If the value
+ is '0', the maximum number is limited only by the
+ IEEE 802.11 standard and any hardware or radio
+ firmware limitations of the access point. The
+ default value is '0'."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 5.7."
+ ::= { cd11IfAuxSsidEntry 4 }
+
+cd11IfAuxSsidMicAlgorithm OBJECT-TYPE
+ SYNTAX CDot11IfMicAlgorithm
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object defines the auxiliary MIC algorithm
+ applied to WEP-encoded packets of stations associated
+ with this radio interface through the cd11IfAuxSsid.
+ The default value is micNone(1)."
+ ::= { cd11IfAuxSsidEntry 5 }
+
+cd11IfAuxSsidWepPermuteAlg OBJECT-TYPE
+ SYNTAX CDot11IfWepKeyPermuteAlgorithm
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object defines the function through which
+ the WEP encryption key is permuted between key renewal
+ periods for stations associated with this radio
+ interface through the cd11IfAuxSsid. The default value
+ is wepPermuteNone(1)."
+ ::= { cd11IfAuxSsidEntry 6 }
+
+
+cd11IfAuxSsidAuthAlgTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfAuxSsidAuthAlgEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table contains attributes to configure
+ authentication algorithms for SSIDs listed in the
+ cd11IfAuxSsidTable. This table extends the
+ IEEE802dot11-MIB dot11AuthenticationAlgorithmsTable
+ for multiple SSIDs support. Multiple SSIDs
+ can associate with an interface and multiple
+ authentication algorithms can apply to an auxiliary
+ SSID.
+
+ This table has an expansion dependent relationship
+ on the ifTable. For each entry in this table,
+ there exists at least an entry in the ifTable of
+ ifType ieee80211(71). Entries in this table cannot
+ be created or deleted by the network management
+ system. All entries are created or deleted by
+ the agent."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 5.7.6."
+ ::= { cd11IfManagement 7 }
+
+cd11IfAuxSsidAuthAlgEntry OBJECT-TYPE
+ SYNTAX Cd11IfAuxSsidAuthAlgEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry specifies authentication algorithm
+ configuration attributes of a VLAN for an auxiliary
+ SSID on a radio interface."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ INDEX {
+ ifIndex,
+ cd11IfAuxSsidIndex,
+ dot11AuthenticationAlgorithmsIndex
+ }
+ ::= { cd11IfAuxSsidAuthAlgTable 1 }
+
+Cd11IfAuxSsidAuthAlgEntry ::=
+ SEQUENCE {
+ cd11IfAuxSsidAuthAlgEnable TruthValue,
+ cd11IfAuxSsidAuthAlgRequireEap TruthValue,
+ cd11IfAuxSsidAuthAlgRequireMac TruthValue,
+ cd11IfAuxSsidAuthAlgDefaultVlan CDot11IfVlanIdOrZero,
+ cd11IfAuxSsidAuthAlgEapMethod SnmpAdminString,
+ cd11IfAuxSsidAuthAlgMacMethod SnmpAdminString
+ }
+
+cd11IfAuxSsidAuthAlgEnable OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If the value is 'true', this device may
+ authenticate an association using SSID (specified
+ by cd11IfAuxiliarySSIDIndex) with the algorithm
+ identified by IEEE802dot11-MIB
+ dot11AuthenticationAlgorithmsIndex. The default
+ value is 'true'."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfAuxSsidAuthAlgEntry 1 }
+
+cd11IfAuxSsidAuthAlgRequireEap OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If both the values of this object and
+ cd11IfAuxSsidAuthAlgEnable are 'true', the
+ association authentication must complete additional
+ network-level EAP authentication before client
+ stations will be unblocked from their association
+ attempts. If the value of this object is 'false'
+ while cd11IfAuxSsidAuthAlgEnable is 'true', client
+ stations will be unblocked as soon as they
+ complete this enabled IEEE 802.11 authentication.
+ The default value is 'true'."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfAuxSsidAuthAlgEntry 2 }
+
+cd11IfAuxSsidAuthAlgRequireMac OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If both the values of this object and
+ cd11IfAuxSsidAuthAlgEnable are 'true', the
+ association authentication must complete additional
+ MAC address authentication before client stations
+ will be unblocked from their association
+ attempts. If the value of this object is 'false'
+ while cd11IfAuxSsidAuthAlgEnable is 'true', client
+ stations will be unblocked as soon as they
+ complete this enabled IEEE 802.11 authentication.
+ The default value is 'true'."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfAuxSsidAuthAlgEntry 3 }
+
+cd11IfAuxSsidAuthAlgDefaultVlan OBJECT-TYPE
+ SYNTAX CDot11IfVlanIdOrZero
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object defines the default VLAN identifier
+ for stations associated with this radio interface
+ with the dot11AuthenticationAlgorithmsIndex
+ authentication defined in IEEE802dot11-MIB and
+ through the cd11IfAuxSsid. If the value
+ of this object is '0', it indicates that either the
+ default VLAN are not defined for that authentication
+ on this radio interface or the default VLAN is the
+ native VLAN ID. The default value is '0'."
+ ::= { cd11IfAuxSsidAuthAlgEntry 4 }
+
+cd11IfAuxSsidAuthAlgEapMethod OBJECT-TYPE
+ SYNTAX SnmpAdminString
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If the value of cd11IfAuxSsidAuthAlgRequireEap
+ is 'true' or dot11AuthenticationAlgorithm is
+ Network-EAP, this is the EAP method list to used
+ for the EAP authentication."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfAuxSsidAuthAlgEntry 5 }
+
+cd11IfAuxSsidAuthAlgMacMethod OBJECT-TYPE
+ SYNTAX SnmpAdminString
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If the value of cd11IfAuxSsidAuthAlgRequireMac
+ is 'true', this is the MAC address method list to
+ used for the MAC authentication."
+ ::= { cd11IfAuxSsidAuthAlgEntry 6 }
+
+
+cd11IfAssignedAidTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfAssignedAidEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "When the radio is not functioning as a client
+ station (i.e., cd11IfStationRole is not
+ 'roleClient'), this is the list of AIDs which this
+ agent will assign to the clients associating with
+ it. An AID is assigned if the corresponding MAC
+ address matches that of the client. This table has
+ an expansion dependent relationship on the ifTable.
+ For each entry in this table, there exists at least
+ an entry in the ifTable of ifType ieee80211(71).
+
+ Entries in this table cannot be created or deleted
+ by the network management system. All entries are
+ created or deleted by the agent."
+ ::= { cd11IfManagement 8 }
+
+cd11IfAssignedAidEntry OBJECT-TYPE
+ SYNTAX Cd11IfAssignedAidEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry associates an AID with a client MAC
+ address. The relationship between AID and client
+ MAC address is one to one."
+ INDEX {
+ ifIndex,
+ cd11IfAssignedAid
+ }
+ ::= { cd11IfAssignedAidTable 1 }
+
+Cd11IfAssignedAidEntry ::=
+ SEQUENCE {
+ cd11IfAssignedAid Unsigned32,
+ cd11IfAssignedSta MacAddress
+ }
+
+cd11IfAssignedAid OBJECT-TYPE
+ SYNTAX Unsigned32 (2..2007)
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This object specifies the AID for a client
+ station to the radio interface."
+ ::= { cd11IfAssignedAidEntry 1 }
+
+cd11IfAssignedSta OBJECT-TYPE
+ SYNTAX MacAddress
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object defines the client station MAC
+ address. When a client associates with this
+ radio interface, it shall always be assigned with
+ the cd11IfAssignedAid as its IEEE 802.11 AID.
+ The default value is '000000000000'H."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 5.7.2."
+ ::= { cd11IfAssignedAidEntry 2 }
+
+
+cd11IfVlanEncryptKeyTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfVlanEncryptKeyEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table contains shared WEP keys for all IEEE
+ 802.11 packets transmitted and received frames over
+ a VLAN identified by the cwvlWlanVlanId if both VLAN
+ and encryption are enabled (i.e., the
+ cwvlWlanEncryptionMode is wep(2) or aes(3)) on the
+ radio interface.
+
+ If WEP encryption is enabled for the transmitted
+ IEEE 802.11 frames, then the Default Shared WEP
+ key in the set is used to encrypt the transmitted
+ broadcast and multicast frames associated with
+ the cwvlWlanVlanId. Key '1' in the set is the
+ default key. If an individual session key is not
+ defined for the target station address, then the
+ Default Shared WEP key will also be used to encrypt
+ or decrypt unicast frames associated with the
+ cwvlWlanVlanId."
+ REFERENCE
+ "CISCO-WLAN-VLAN-MIB, June 2002, Cisco Systems
+ Wireless Virtual LAN MIB."
+ ::= { cd11IfManagement 9 }
+
+cd11IfVlanEncryptKeyEntry OBJECT-TYPE
+ SYNTAX Cd11IfVlanEncryptKeyEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry contains the key index, key length, and
+ key value. There is a maximum of 4 keys per VLAN or
+ key set. Each key set exists only if the
+ corresponding VLAN is enabled on the interface, and
+ it is indexed by the VLAN ID."
+ INDEX {
+ ifIndex,
+ cd11IfVlanId,
+ cd11IfVlanEncryptKeyIndex
+ }
+ ::= { cd11IfVlanEncryptKeyTable 1 }
+
+Cd11IfVlanEncryptKeyEntry
+ ::= SEQUENCE {
+ cd11IfVlanId CDot11IfVlanIdOrZero,
+ cd11IfVlanEncryptKeyIndex Unsigned32,
+ cd11IfVlanEncryptKeyLen Unsigned32,
+ cd11IfVlanEncryptKeyValue WepKeyType128,
+ cd11IfVlanEncryptKeyStatus RowStatus,
+ cd11IfVlanEncryptKeyTransmit TruthValue
+ }
+
+cd11IfVlanId OBJECT-TYPE
+ SYNTAX CDot11IfVlanIdOrZero
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This object identifies the VLAN (1 to 4095) on
+ this radio interface. The object value should
+ match the corresponding cwvlWlanVlanId in the
+ cwvlWlanVlanTable or cd11IfVlanSecurityVlanId
+ object in the cd11IfVlanSecurityTable. When
+ the value is '0', the encryption keys are applied
+ to the non-VLAN configuration."
+ REFERENCE
+ "CISCO-WLAN-VLAN-MIB, June 2002, Cisco Systems
+ Wireless Virtual LAN MIB."
+ ::= { cd11IfVlanEncryptKeyEntry 1 }
+
+cd11IfVlanEncryptKeyIndex OBJECT-TYPE
+ SYNTAX Unsigned32 (1..4)
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This object is a representative of the
+ corresponding 802.11 WEP Key Index used when
+ transmitting or receiving frames with this key.
+ SNMP table indexing conventions require table
+ index to be non-zero. Therefore, this object has
+ to be one greater than the actual 802.11 WEP key
+ index. A value of '1' for this object corresponds
+ to a value of '0' for the 802.11 WEP key index."
+ ::= { cd11IfVlanEncryptKeyEntry 2 }
+
+cd11IfVlanEncryptKeyLen OBJECT-TYPE
+ SYNTAX Unsigned32 (0..13)
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object specifies the length in octets of
+ cd11IfVlanEncryptKeyValue. Common values are 5 for
+ 40-bit WEP key and 13 for 128-bit WEP key. A value
+ of '0' means that the key is not set but the VLAN
+ is enabled."
+ DEFVAL { 0 }
+ ::= { cd11IfVlanEncryptKeyEntry 3 }
+
+cd11IfVlanEncryptKeyValue OBJECT-TYPE
+ SYNTAX WepKeyType128
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This is the WEP secret key value. The agent
+ always returns a zero-length string when this
+ object is read for security reason."
+ ::= { cd11IfVlanEncryptKeyEntry 4 }
+
+cd11IfVlanEncryptKeyStatus OBJECT-TYPE
+ SYNTAX RowStatus
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object controls and reflects the status of
+ rows in this table.
+
+ When the row in 'active' state, the NMS can modify
+ both key length and value. To delete a row, set this
+ object value to 'destroy'."
+ ::= { cd11IfVlanEncryptKeyEntry 5 }
+
+cd11IfVlanEncryptKeyTransmit OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "Only one of the 4 keys of a VLAN can be the transmit
+ key. Setting any one of the 4 keys to 'true', the
+ agent will automatically change the value of
+ cd11IfVlanEncryptKeyTransmit of the other 3 keys to
+ 'false' if they exist."
+ ::= { cd11IfVlanEncryptKeyEntry 6 }
+
+
+
+cd11IfVlanSecurityTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfVlanSecurityEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table contains encryption method and key
+ rotation configurations for all VLANs on all
+ IEEE 802.11 radio interfaces. This table has an
+ expansion dependent relationship on the ifTable.
+ For each entry in this table, there exists at least
+ an entry in the ifTable of ifType ieee80211(71).
+
+ VLANs are identified by the cd11IfVlanSecurityVlanId,
+ and the actual VLAN does not have to exist or be
+ enabled for the encryption configuration to exist."
+ ::= { cd11IfManagement 10 }
+
+cd11IfVlanSecurityEntry OBJECT-TYPE
+ SYNTAX Cd11IfVlanSecurityEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry is a set of encryption configurations
+ for traffic on a VLAN of a IEEE 802.11 radio
+ interface."
+ INDEX {
+ ifIndex,
+ cd11IfVlanSecurityVlanId
+ }
+ ::= { cd11IfVlanSecurityTable 1 }
+
+Cd11IfVlanSecurityEntry
+ ::= SEQUENCE {
+ cd11IfVlanSecurityVlanId CDot11IfVlanIdOrZero,
+ cd11IfVlanSecurityVlanEnabled TruthValue,
+ cd11IfVlanBcastKeyChangeInterval Unsigned32,
+ cd11IfVlanBcastKeyCapabilChange TruthValue,
+ cd11IfVlanBcastKeyClientLeave TruthValue,
+ cd11IfVlanSecurityCiphers CDot11IfCipherType,
+ cd11IfVlanSecurityRowStatus RowStatus,
+ cd11IfVlanEncryptionMode INTEGER,
+ cd11IfVlanWepEncryptOptions INTEGER,
+ cd11IfVlanWepEncryptMic TruthValue,
+ cd11IfVlanWepEncryptKeyHashing TruthValue,
+ cd11IfVlanPsPacketForwardEnable TruthValue
+ }
+
+cd11IfVlanSecurityVlanId OBJECT-TYPE
+ SYNTAX CDot11IfVlanIdOrZero
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This is the VLAN ID (1-4095) to which the
+ parameters in each conceptual row shall be
+ applied. If the value is '0', these parameters
+ apply to the non-VLAN configuration."
+ ::= { cd11IfVlanSecurityEntry 1 }
+
+cd11IfVlanSecurityVlanEnabled OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "If the value is 'true', this VLAN sub-interface is
+ enabled on all trunk and hybrid ports. If the value
+ is 'false', this VLAN is disabled on all ports. For
+ platforms supporting NMS to create VLAN sub-interfaces,
+ setting this object to 'true' will create the
+ corresponding VLAN sub-interfaces on all ports and
+ 'false' will remove the the corresponding VLAN."
+ ::= { cd11IfVlanSecurityEntry 2 }
+
+cd11IfVlanBcastKeyChangeInterval OBJECT-TYPE
+ SYNTAX Unsigned32 (0|10..10000000)
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This is the broadcast key rotation period. If the
+ value is '0', there is no key rotation."
+ ::= { cd11IfVlanSecurityEntry 3 }
+
+cd11IfVlanBcastKeyCapabilChange OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "If it is 'true', a new key will be used every time
+ when the common set of encryption capability among
+ clients of this radio on this VLAN is changed."
+ DEFVAL { false }
+ ::= { cd11IfVlanSecurityEntry 4 }
+
+cd11IfVlanBcastKeyClientLeave OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "If it is 'true', a new key will be used every time
+ when a client of the radio on this VLAN disassociates."
+ DEFVAL { false }
+ ::= { cd11IfVlanSecurityEntry 5 }
+
+cd11IfVlanSecurityCiphers OBJECT-TYPE
+ SYNTAX CDot11IfCipherType
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "If cd11IfVlanEncryptionMode is cipher(1), these
+ are all the possible cipher type combinations
+ currently supported for data frame encryption from
+ different IEEE 802.11 radio interface implementations.
+ Some platform may support only a subset of the
+ combinations. Agent will not honor invalid
+ combinations. If none of the bits are set, no
+ encryption will be done.
+ aesccm WPA AES CCMP encryption,
+ ckip Cisco Per packet key hashing,
+ cmic Cisco MMH MIC,
+ ckip|cmic Cisco Per packet key hashing and MIC,
+ tkip WPA Temporal Key encryption,
+ wep128 128-bit WEP key,
+ wep40 40-bit WEP key.
+ tkip|wep128 WPA Temporal Key and 128-bit WEP,
+ tkip|wep40 WPA Temporal Key and 40-bit WEP."
+ ::= { cd11IfVlanSecurityEntry 6 }
+
+cd11IfVlanSecurityRowStatus OBJECT-TYPE
+ SYNTAX RowStatus
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This is used to create a new row, modify or
+ delete an existing VLAN encryption configuration
+ in this table.
+
+ Creation of rows must be done via 'createAndGo' and
+ cd11IfVlanSecurityVlanEnabled and
+ cd11IfVlanSecurityCiphers columns are mandatory.
+ This object will become 'active' if the NMS performs
+ a multivarbind set including this object and
+ successfully creates the encryption configuration.
+
+ Modification and deletion of rows can be done via
+ 'createAndGo' and 'delete' respectively when this
+ object is 'active'. Any encryption configurations
+ of a VLAN should only be deleted when it is not
+ being used for any client association."
+ ::= { cd11IfVlanSecurityEntry 7 }
+
+cd11IfVlanEncryptionMode OBJECT-TYPE
+ SYNTAX INTEGER {
+ cipher(1),
+ wep(2)
+ }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "Encryption mode this VLANs are:
+ cipher(1) - WPA and Cisco encryptions,
+ wep(2) - WEP Only encryption"
+ DEFVAL { cipher }
+ ::= { cd11IfVlanSecurityEntry 8 }
+
+cd11IfVlanWepEncryptOptions OBJECT-TYPE
+ SYNTAX INTEGER {
+ mandatory(1),
+ optional(2)
+ }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "If cd11IfVlanEncryptionMode is wep(2),
+ mandatory(1) - WEP encryption is mandatory,
+ optional(2) - WEP encryption is option.
+ for all data frames on this VLAN."
+ DEFVAL { mandatory }
+ ::= { cd11IfVlanSecurityEntry 9 }
+
+cd11IfVlanWepEncryptMic OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "If cd11IfVlanEncryptionMode is wep(2) and
+ this object is 'true', MIC will be performed
+ on all data frames on this VLAN. Otherwise,
+ no MIC will be done."
+ DEFVAL { false }
+ ::= { cd11IfVlanSecurityEntry 10 }
+
+cd11IfVlanWepEncryptKeyHashing OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "If cd11IfVlanEncryptionMode is wep(2) and
+ this object is 'true', key hashing will be
+ used for encryption. Otherwise, no key
+ hashing will be done."
+ DEFVAL { false }
+ ::= { cd11IfVlanSecurityEntry 11 }
+
+cd11IfVlanPsPacketForwardEnable OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "If both cd11IfVlanSecurityVlanEnabled and this
+ object are 'true', PSPF is enabled on VLAN
+ cd11IfVlanSecurityVlanId of this radio interface
+ and direct traffic between wireless clients of the
+ VLAn is not allowed. Otherwise, PSPF is disabled
+ on the VLAN and direct traffic between wireless
+ clients of the VLAN is allowed."
+ DEFVAL { false }
+ ::= { cd11IfVlanSecurityEntry 12 }
+
+
+cd11IfRadioMonitoringTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfRadioMonitoringEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table is for monitoring of remote active
+ IEEE 802.11 radio devices on the network.
+ Each table entry shows an active radio being
+ monitored by a hot standby radio on this
+ monitoring unit.
+
+ This table has a sparse dependent relationship
+ on the ifTable. For each entry in this table,
+ there exists an entry in the ifTable of ifType
+ ieee80211(71). Entries on this table can be
+ added, deleted, and modified by the NMS."
+ ::= { cd11IfManagement 11 }
+
+cd11IfRadioMonitoringEntry OBJECT-TYPE
+ SYNTAX Cd11IfRadioMonitoringEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry specifies the MAC address of the remote
+ radio and the monitoring configuration and status
+ of the local radio. Most platforms supporting this
+ table only support one entry per ifIndex."
+ INDEX {
+ ifIndex,
+ cd11IfRemoteRadioMacAddr
+ }
+ ::= { cd11IfRadioMonitoringTable 1 }
+
+Cd11IfRadioMonitoringEntry
+ ::= SEQUENCE {
+ cd11IfRemoteRadioMacAddr MacAddress,
+ cd11IfRadioMonitorPollingFreq Unsigned32,
+ cd11IfRadioMonitorPollingTimeOut Unsigned32,
+ cd11IfLocalRadioMonitorStatus INTEGER,
+ cd11IfRadioMonitorRowStatus RowStatus
+ }
+
+cd11IfRemoteRadioMacAddr OBJECT-TYPE
+ SYNTAX MacAddress
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Mac address of the active IEEE 802.11 radio device
+ to be monitored by this hot standby monitoring radio.
+ The cd11IfPhyMacSpecification of the local and remote
+ radios must be the same in order for the monitoring to
+ happen."
+ ::= { cd11IfRadioMonitoringEntry 1 }
+
+cd11IfRadioMonitorPollingFreq OBJECT-TYPE
+ SYNTAX Unsigned32 (1..30)
+ UNITS "seconds"
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "The frequency, in seconds, the remote active radio
+ specified by cd11IfRemoteRadioMacAddr is polled
+ for its health."
+ DEFVAL { 5 }
+ ::= { cd11IfRadioMonitoringEntry 2 }
+
+
+cd11IfRadioMonitorPollingTimeOut OBJECT-TYPE
+ SYNTAX Unsigned32 (1..600)
+ UNITS "seconds"
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "The total time, in seconds, this standby monitoring
+ radio unit can tolerate the failure of polling
+ of the active radio unit. After this duration, one
+ more failure of the polling will trigger this hot
+ standby monitoring radio to take over and become an
+ active radio. It will then stop all monitoring
+ activity and set the instance of
+ cd11IfLocalRadioMonitorStatus indexed by the
+ failed radio cd11IfRemoteRadioMacAddr to 'active'."
+ DEFVAL { 5 }
+ ::= { cd11IfRadioMonitoringEntry 3 }
+
+cd11IfLocalRadioMonitorStatus OBJECT-TYPE
+ SYNTAX INTEGER {
+ active(1),
+ monitor(2),
+ inactive(3)
+ }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "NMS can only set this object to monitor(2). In
+ the monitor(2) state, this local radio will monitor
+ the remote radio specified in the
+ cd11IfRemoteRadioMacAddr.
+
+ When the remote radio fails or goes down, this local
+ radio will takeover the functions and became active.
+ The agent will set the instance of
+ cd11IfLocalRadioMonitorStatus indexed by the
+ failed radio cd11IfRemoteRadioMacAddr to 'active'.
+
+ This local radio will not monitor any other radios
+ when it is active, therefore, all other instances of
+ cd11IfLocalRadioMonitorStatus indexed by the same
+ ifIndex but different cd11IfRemoteRadioMacAddr
+ will be set to 'inactive'."
+ ::= { cd11IfRadioMonitoringEntry 4 }
+
+cd11IfRadioMonitorRowStatus OBJECT-TYPE
+ SYNTAX RowStatus
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object is used for creating, modifying, and
+ deleting rows in this table.
+
+ Creation of rows must be done via 'createAndGo'.
+ This object will become 'active' if the NMS performs
+ a multivarbind set including this object.
+
+ Any object in a row can be modified any time when
+ the row is in the 'active' state via 'createAndGo'.
+
+ Removal of a row can be done via setting this
+ object to 'destroy'."
+ ::= { cd11IfRadioMonitoringEntry 5 }
+
+
+cd11IfDot11UpgradeStatusTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfDot11UpgradeStatusEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table represents the status of upgrade of
+ the radios to the newer frequencies of the 5150-5250
+ MHz band.
+
+ This table has a sparse dependent relationship on the
+ ifTable. For each entry in this table, there exists
+ an entry in the ifTable of ifType ieee80211(71).
+
+ Entries in this table cannot be created or deleted
+ by the network management system. All entries are
+ created or deleted by the agent. "
+ ::= { cd11IfManagement 12 }
+
+cd11IfDot11UpgradeStatusEntry OBJECT-TYPE
+ SYNTAX Cd11IfDot11UpgradeStatusEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry corresponds to one conceptual row in
+ cd11IfDot11UpgradeStatusTable and represents the
+ status of upgrade of a dot11 radio interface. "
+ INDEX { ifIndex }
+ ::= { cd11IfDot11UpgradeStatusTable 1 }
+
+Cd11IfDot11UpgradeStatusEntry ::=
+ SEQUENCE {
+ cd11IfDot11UpgradeStatus Cd11IfDot11UpgradeStatus
+ }
+
+cd11IfDot11UpgradeStatus OBJECT-TYPE
+ SYNTAX Cd11IfDot11UpgradeStatus
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object represents the status of upgrade of
+ a dot11 radio interface. "
+ ::= {cd11IfDot11UpgradeStatusEntry 1 }
+
+
+cd11IfPhyOperationTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfPhyOperationEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table contains the IEEE 802.11 Physical
+ Layer operation configuration parameters for
+ each radio interface. This table has a sparse
+ dependent relationship on the ifTable.
+ For each entry in this table, there exists an
+ entry in the ifTable of ifType ieee80211(71).
+ Entries in this table cannot be created or deleted
+ by the network management system. All entries are
+ created or deleted by the agent."
+ ::= { cd11IfPhyConfig 1 }
+
+cd11IfPhyOperationEntry OBJECT-TYPE
+ SYNTAX Cd11IfPhyOperationEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A collection of attributes defining the physical
+ characteristics and behaviors of an IEEE 802.11 PHY."
+ INDEX { ifIndex }
+ ::= { cd11IfPhyOperationTable 1 }
+
+Cd11IfPhyOperationEntry ::=
+ SEQUENCE {
+ cd11IfCurrentCarrierSet INTEGER,
+ cd11IfModulationType INTEGER,
+ cd11IfPreambleType INTEGER,
+ cd11IfDomainCapabilitySet Integer32,
+ cd11IfPhyBasicRateSet OCTET STRING,
+ cd11IfPhyMacSpecification INTEGER,
+ cd11IfPhyConcatenation Integer32,
+ cd11IfPhyNativePowerUseStandard
+ TruthValue
+ }
+
+cd11IfCurrentCarrierSet OBJECT-TYPE
+ SYNTAX INTEGER {
+ usa(0),
+ europe(1),
+ japan(2),
+ spain(3),
+ france(4),
+ belgium(5),
+ israel(6),
+ canada(7),
+ australia(8),
+ japanWide(9),
+ world(10),
+ usa5GHz(11),
+ europe5GHz(12),
+ japan5GHz(13),
+ singapore5GHz(14),
+ taiwan5GHz(15),
+ china(16),
+ northAmer5GHzUNI3(17),
+ chnIreAus5GHzUNI3(18),
+ hkNZ5GHzUNI3(19),
+ korea5GHzUNI3(20),
+ mexAusNZ5GHz(21),
+ china5GHz(22),
+ korea5GHzUNI123E(23),
+ japan5GHzUNI12(24),
+ taiwan5GHzUNI23E(25),
+ israel5GhzUNI12(26),
+ usaFCC49PS(27),
+ japan5GHzUNI1(28)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object defines the carrier set of the radio.
+ The carrier set implies a regulatory domain, but
+ geographic-specific restrictions within a regulatory
+ domain may necessitate several carrier sets within
+ the regulatory domain.
+ usa(0) - ISM 2.4 GHz America
+ europe(1) - ISM 2.4 GHz Europe
+ japan(2) - ISM 2.4 GHz Japan
+ spain(3) - ISM 2.4 GHz Spain
+ france(4) - ISM 2.4 GHz France
+ belgium(5) - ISM 2.4 GHz Belgium
+ israel(6) - ISM 2.4 GHz Israel
+ canada(7) - ISM 2.4 GHz Canada
+ australia(8) - ISM 2.4 GHz Australia
+ japanWide(9) - ISM 2.4 GHz JapanWide
+ world(10) - ISM 2.4 GHz World
+ usa5GHz(11) - OFDM UNII 2 America
+ europe5GHz(12) - OFDM UNII 2 Europe
+ japan5GHz(13) - OFDM UNII 2 Japan
+ singapore5GHz(14) - OFDM UNII 2 Singapore
+ taiwan5GHz(15) - OFDM UNII 2 Taiwan
+ china(16) - ISM 2.4 GHz China
+ northAmer5GHzUNI3(17)
+ - OFDM UNII 3 North America
+ chnIreAus5GHzUNI3(18)
+ - OFDM UNII 3 China, Ireland, Austrialia
+ hkNZ5GHzUNI3(19)
+ - OFDM UNII 3 Hong Kong, New Zealand
+ korea5GHzUNI3(20)
+ - OFDM UNII 3 Korea
+ mexAusNZ5GHzUNI3(21)
+ - OFDM UNII 3 Mexical, Australia,
+ New Zealand (North America without
+ ETSI Channels)
+ china5GHzUNI2(22)
+ - OFDM UNII 2 China
+ korea5GHzUNI123E(23)
+ - OFDM UNII 1,2,3,ETSI Korea
+ japan5GHzUNI12(24)
+ - OFDM UNII 1,2 Japan
+ taiwan5GHzUNI23E(25)
+ - OFDM UNII 2,3,ETSI Taiwan
+ israel5GhzUNI12(26)
+ - OFDM UNII 1,2 Israel
+ usaFCC49PS(27)
+ - OFDM FCC49 USA Public Safety
+ japan5GHzUNI1(28)
+ - OFDM UNII 1 Japan"
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 14.6.10."
+ ::= { cd11IfPhyOperationEntry 1 }
+
+cd11IfModulationType OBJECT-TYPE
+ SYNTAX INTEGER {
+ standard(1),
+ mok(2)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object specifies the RF modulation type of
+ the radio.
+ standard(1) - Standard, this is the default
+ setting currently defined in the
+ IEEE 802.11 standard.
+ mok(2) - MOK, this modulation was used
+ before the IEEE finished the
+ high-speed 802.11 standard.
+ The default modulation type is standard(1)."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 14.6.10."
+ ::= { cd11IfPhyOperationEntry 2 }
+
+cd11IfPreambleType OBJECT-TYPE
+ SYNTAX INTEGER {
+ long(1),
+ short(2)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object specifies the current radio preamble
+ type in use by the station. Possible values:
+ long(1) - long preambles
+ short(2) - short preambles.
+ A long preamble ensures compatibility between
+ access point and all early models of Cisco
+ Aironet Wireless LAN adapters (client devices).
+ A short preamble improves throughput performance.
+ The default preamble type is short(2)."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 14.6.10."
+ ::= { cd11IfPhyOperationEntry 3 }
+
+cd11IfDomainCapabilitySet OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object specifies the current multi-domain
+ capability setting of this radio. This object
+ takes one of the dot11MultiDomainCapabilityIndex
+ values on the dot11MultiDomainCapabilityTable.
+
+ The setting controls the first working radio channel
+ number, the number of working channels, and the
+ maximum transmit power level of the radio. The
+ setting must match the corresponding value of the
+ cd11IfCurrentCarrierSet set for this radio. This
+ object is writable only if the IEEE 802.11
+ multi-domain capability option is implemented
+ and enabled via dot11MultiDomainCapabilityImplemented
+ and dot11MultiDomainCapabilityEnabled."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfPhyOperationEntry 4 }
+
+cd11IfPhyBasicRateSet OBJECT-TYPE
+ SYNTAX OCTET STRING (SIZE(1..126))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This attribute specifies if a data rate in the
+ dot11OperationalRateSet of the IEEE802dot11-MIB
+ is a Basic Rate for this radio interface.
+ If a data rate is a Basic Rate, the corresponding
+ octet of this attribute will contain a value of
+ 128 (or the most significant bit is set). Otherwise,
+ the corresponding octet of this attribute will
+ be 0."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfPhyOperationEntry 5 }
+
+cd11IfPhyMacSpecification OBJECT-TYPE
+ SYNTAX INTEGER {
+ ieee802dot11a(1),
+ ieee802dot11b(2),
+ ieee802dot11g(3)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object specifies which IEEE 802.11 Standard
+ applies to this radio interface.
+ ieee802dot11a(1) - IEEE 802.11a Standard,
+ ieee802dot11b(2) - IEEE 802.11b Standard,
+ ieee802dot11g(3) - IEEE 802.11g Standard."
+ REFERENCE
+ "IEEE P802.11g (expected June 2003), Wireless LAN
+ Medium Access Control (MAC) and Physical Layer (PHY)
+ Specifications: Higher Speed Physical Layer (PHY)
+ Extension to IEEE 802.11b."
+ ::= { cd11IfPhyOperationEntry 6 }
+
+cd11IfPhyConcatenation OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If the value of cd11IfStationRole is 'roleBridge'
+ or 'roleNrBridge', this object sets the maximum
+ packet concatenation size in bytes for all
+ outbound packets. For our current 5 GHz product,
+ the maximum value range is from 1600 to 4000."
+ ::= { cd11IfPhyOperationEntry 7 }
+
+cd11IfPhyNativePowerUseStandard OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object indicates if queries for current
+ transmit power and number of transmit power levels
+ of the radio for the frequency band shall be via
+ the Standard IEEE802dot11-MIB dot11PhyTxPowerTable
+ dot11CurrentTxPowerLevel and
+ dot11NumberSupportedPowerLevels objects or
+ corresponding cd11IfNativeCurrentPowerLevel
+ and cd11IfNativeNumberPowerLevels objects
+ in the cd11IfRfNativePowerTable.
+
+ If the value is 'true', the dot11CurrentTxPowerLevel
+ is used to configure the current radio transmit
+ power level. If the value is 'false', the
+ cd11IfNativeCurrentPowerLevel object shall be used
+ to configure the current radio transmit power level."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ DEFVAL { true }
+ ::= { cd11IfPhyOperationEntry 8 }
+
+
+cd11IfPhyFhssTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfPhyFhssEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table contains the Physical Layer
+ Frequency Hopping Spread Spectrum configuration
+ parameters for each radio interface. This table
+ has a sparse dependent relationship on the ifTable.
+ For each entry in this table, there exists an
+ entry in the ifTable of ifType ieee80211(71).
+ Entries in this table cannot be created or deleted
+ by the network management system. All entries are
+ created or deleted by the agent."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 14.1.2."
+ ::= { cd11IfPhyConfig 4 }
+
+cd11IfPhyFhssEntry OBJECT-TYPE
+ SYNTAX Cd11IfPhyFhssEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A collection of attributes defining the FHSS
+ configuration parameters of a radio interface."
+ INDEX { ifIndex }
+ ::= { cd11IfPhyFhssTable 1 }
+
+Cd11IfPhyFhssEntry ::=
+ SEQUENCE {
+ cd11IfPhyFhssMaxCompatibleRate Integer32
+ }
+
+cd11IfPhyFhssMaxCompatibleRate OBJECT-TYPE
+ SYNTAX Integer32 (2..127)
+ UNITS "500 Kb per second"
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object specifies the of maximum data
+ rate at which the station may transmit data.
+ The octet contains a value representing a rate.
+ The rate should be within the range from '2' to
+ '127', corresponding to data rates in increments
+ of 500 kb/s from 1 Mb/s to 63.5 Mb/s. It should be
+ one of the rates in the IEEE802dot11-MIB
+ dot11OperationalRateSet. The default value is
+ '127'."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfPhyFhssEntry 1 }
+
+
+cd11IfPhyDsssTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfPhyDsssEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table contains the Physical Layer
+ Direct Sequence Spread Spectrum configuration
+ parameters for each radio interface. This table
+ has a sparse dependent relationship on the ifTable.
+ For each entry in this table, there exists an
+ entry in the ifTable of ifType ieee80211(71).
+ Entries in this table cannot be created or deleted
+ by the network management system. All entries are
+ created or deleted by the agent."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 15.1."
+ ::= { cd11IfPhyConfig 5 }
+
+cd11IfPhyDsssEntry OBJECT-TYPE
+ SYNTAX Cd11IfPhyDsssEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "A collection of attributes defining the DSSS
+ configuration parameters of a radio interface."
+ INDEX { ifIndex }
+ ::= { cd11IfPhyDsssTable 1 }
+
+Cd11IfPhyDsssEntry ::=
+ SEQUENCE {
+ cd11IfPhyDsssMaxCompatibleRate Integer32,
+ cd11IfPhyDsssChannelAutoEnable TruthValue,
+ cd11IfPhyDsssCurrentChannel INTEGER
+ }
+
+cd11IfPhyDsssMaxCompatibleRate OBJECT-TYPE
+ SYNTAX Integer32 (2..127)
+ UNITS "500 Kb per second"
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object specifies the of maximum data
+ rate at which the station may transmit data.
+ The octet contains a value representing a rate.
+ The rate should be within the range from '2' to
+ '127', corresponding to data rates in increments
+ of 500 kb/s from 1 Mb/s to 63.5 Mb/s. It should
+ be one of the rates in the IEEE802dot11-MIB
+ dot11OperationalRateSet. The default value is
+ '127'."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfPhyDsssEntry 1 }
+
+cd11IfPhyDsssChannelAutoEnable OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If the value is 'true' and the radio is function
+ as an access point device (i.e., cd11IfStationRole
+ is 'roleRoot', the radio will scan for other BSS
+ activity on all channels available in the current
+ cd11IfCurrentCarrierSet before establishing its
+ own BSS. After the scan, this station will
+ establish its own BSS on the channel with the
+ least probability of radio signal congestion.
+ If the value is 'false', this station always
+ establishes its BSS on IEEE802dot11-MIB
+ dot11CurrentChannel. The default value is 'true'."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfPhyDsssEntry 2 }
+
+cd11IfPhyDsssCurrentChannel OBJECT-TYPE
+ SYNTAX INTEGER (1..14 |
+ 34|36|38|40|42|44|46|48|52|56|60|64 |
+ 149|153|157|161)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The current operating frequency channel of
+ the DSSS PHY, as selected either by selective
+ scanning or via IEEE802dot11-MIB dot11CurrentChannel.
+ Valid channel numbers are defined in the
+ IEEE 802.11 Standard.
+
+ For North America, 802.11b channels allowed are 1 to
+ 11 and 802.11a channels allowed are 36,40,44,48,52,56,
+ 60, and 64."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 15.4.6.2."
+ ::= { cd11IfPhyDsssEntry 3 }
+
+
+cd11IfSuppDataRatesPrivacyTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfSuppDataRatesPrivacyEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table defines the transmit and receive bit
+ rate of the radio on each IEEE 802.11 interface
+ and the WEP encryption support at those rates.
+ This table has an expansion dependent relationship
+ on the ifTable. For each entry in this table,
+ there exists at least an entry in the ifTable of
+ ifType ieee80211(71). Entries in this table
+ cannot be created or deleted by the network
+ management system. All entries are created or
+ deleted by the agent."
+ ::= { cd11IfPhyConfig 11 }
+
+cd11IfSuppDataRatesPrivacyEntry OBJECT-TYPE
+ SYNTAX Cd11IfSuppDataRatesPrivacyEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry specifies the encryption support for
+ a particular data rate on a radio interface."
+ INDEX {
+ ifIndex,
+ cd11IfSuppDataRatesPrivacyIndex
+ }
+ ::= { cd11IfSuppDataRatesPrivacyTable 1 }
+
+Cd11IfSuppDataRatesPrivacyEntry ::=
+ SEQUENCE {
+ cd11IfSuppDataRatesPrivacyIndex Integer32,
+ cd11IfSuppDataRatesPrivacyValue Integer32,
+ cd11IfSuppDataRatesPrivacyEnabl TruthValue
+ }
+
+cd11IfSuppDataRatesPrivacyIndex OBJECT-TYPE
+ SYNTAX Integer32 (1..8)
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This object identifies a data rate supported
+ on a radio. Each radio can support up to 8
+ different rates."
+ ::= { cd11IfSuppDataRatesPrivacyEntry 1 }
+
+cd11IfSuppDataRatesPrivacyValue OBJECT-TYPE
+ SYNTAX Integer32 (2..127)
+ UNITS "500 Kb per second"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object defines the receiving or transmission
+ bit rates supported by the PLCP and PMD, represented
+ by a count from 0x02-0x7f, corresponding to
+ data rates in increments of 500Kb/s from 1 Mb/s to
+ 63.5 Mb/s."
+ ::= { cd11IfSuppDataRatesPrivacyEntry 2 }
+
+cd11IfSuppDataRatesPrivacyEnabl OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object indicates whether WEP encryption is
+ supported by the radio for both transmit and receive
+ operations at the corresponding bit rate specified
+ by the cd11IfSuppDataRatesPrivacyValue."
+ ::= { cd11IfSuppDataRatesPrivacyEntry 3 }
+
+
+cd11IfChanSelectTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfChanSelectEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table specifies for each 802.11 channel,
+ whether the scanning process controlled by the
+ cd11IfPhyDsssChannelAutoEnable can select a
+ particular channel for use. This table has an
+ expansion dependent relationship on the ifTable.
+ For each entry in this table, there exists at least
+ an entry in the ifTable of ifType ieee80211(71).
+ Entries in this table cannot be created or deleted
+ by the network management system. All entries are
+ created or deleted by the agent."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 15.4.6.2."
+ ::= { cd11IfPhyConfig 12 }
+
+cd11IfChanSelectEntry OBJECT-TYPE
+ SYNTAX Cd11IfChanSelectEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry specifies if a particular radio channel
+ is enabled on a radio interface."
+ INDEX {
+ ifIndex,
+ cd11IfChanSelectChannel
+ }
+ ::= { cd11IfChanSelectTable 1 }
+
+Cd11IfChanSelectEntry ::=
+ SEQUENCE {
+ cd11IfChanSelectChannel INTEGER,
+ cd11IfChanSelectEnable TruthValue
+ }
+
+cd11IfChanSelectChannel OBJECT-TYPE
+ SYNTAX INTEGER (1..14 |
+ 34|36|38|40|42|44|46|48|52|56|60|64 |
+ 149|153|157|161)
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This object specifies an IEEE 802.11 channel
+ number which is a candidate for low-occupancy
+ scanning."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, section 15.4.6.2."
+ ::= { cd11IfChanSelectEntry 1 }
+
+cd11IfChanSelectEnable OBJECT-TYPE
+ SYNTAX TruthValue
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If the value is 'true', cd11IfChanSelectChannel
+ is available for the system to use as its
+ cd11IfPhyDsssCurrentChannel after scanning for
+ channel occupancy. If the value is 'false',
+ cd11IfChanSelectChannel is not available. The
+ default value is 'true'."
+ ::= { cd11IfChanSelectEntry 2 }
+
+
+cd11IfClientTxPowerTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfClientTxPowerEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table shows the recommended client
+ transmit power level for the radio and selects
+ one of the levels as the desired transmit power
+ level to be used by the client of the radio. By
+ adjusting the transmit power, the radio can limit
+ the interference caused by adjacent clients using
+ the same or adjacent channels."
+ ::= { cd11IfPhyConfig 13 }
+
+cd11IfClientTxPowerEntry OBJECT-TYPE
+ SYNTAX Cd11IfClientTxPowerEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry specifies the number of available
+ transmit power levels, the values of all the
+ levels, and the selected level for a radio
+ interface."
+ INDEX { ifIndex }
+ ::= { cd11IfClientTxPowerTable 1 }
+
+Cd11IfClientTxPowerEntry ::=
+ SEQUENCE {
+ cd11IfClientNumberTxPowerLevels Integer32,
+ cd11IfClientTxPowerLevel1 Integer32,
+ cd11IfClientTxPowerLevel2 Integer32,
+ cd11IfClientTxPowerLevel3 Integer32,
+ cd11IfClientTxPowerLevel4 Integer32,
+ cd11IfClientTxPowerLevel5 Integer32,
+ cd11IfClientTxPowerLevel6 Integer32,
+ cd11IfClientTxPowerLevel7 Integer32,
+ cd11IfClientTxPowerLevel8 Integer32,
+ cd11IfClientCurrentTxPowerLevel Integer32
+ }
+
+cd11IfClientNumberTxPowerLevels OBJECT-TYPE
+ SYNTAX Integer32 (1..8)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The number of power levels available for the
+ clients. This attribute can have a value of
+ 1 to 8."
+ ::= { cd11IfClientTxPowerEntry 1 }
+
+cd11IfClientTxPowerLevel1 OBJECT-TYPE
+ SYNTAX Integer32 (-10000..10000)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The client transmit output power for LEVEL1
+ in mW or dBm."
+ ::= { cd11IfClientTxPowerEntry 2 }
+
+cd11IfClientTxPowerLevel2 OBJECT-TYPE
+ SYNTAX Integer32 (-10000..10000)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The client transmit output power for LEVEL2
+ in mW or dBm."
+ ::= { cd11IfClientTxPowerEntry 3 }
+
+cd11IfClientTxPowerLevel3 OBJECT-TYPE
+ SYNTAX Integer32 (-10000..10000)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The client transmit output power for LEVEL3
+ in mW or dBm."
+ ::= { cd11IfClientTxPowerEntry 4 }
+
+cd11IfClientTxPowerLevel4 OBJECT-TYPE
+ SYNTAX Integer32 (-10000..10000)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The client transmit output power for LEVEL4
+ in mW or dBm."
+ ::= { cd11IfClientTxPowerEntry 5 }
+
+cd11IfClientTxPowerLevel5 OBJECT-TYPE
+ SYNTAX Integer32 (-10000..10000)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The client transmit output power for LEVEL5
+ in mW or dBm."
+ ::= { cd11IfClientTxPowerEntry 6 }
+
+cd11IfClientTxPowerLevel6 OBJECT-TYPE
+ SYNTAX Integer32 (-10000..10000)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The client transmit output power for LEVEL6
+ in mW or dBm."
+ ::= { cd11IfClientTxPowerEntry 7 }
+
+cd11IfClientTxPowerLevel7 OBJECT-TYPE
+ SYNTAX Integer32 (-10000..10000)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The client transmit output power for LEVEL7
+ in mW or dBm."
+ ::= { cd11IfClientTxPowerEntry 8 }
+
+cd11IfClientTxPowerLevel8 OBJECT-TYPE
+ SYNTAX Integer32 (-10000..10000)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The client transmit output power for LEVEL8
+ in mW or dBm."
+ ::= { cd11IfClientTxPowerEntry 9 }
+
+cd11IfClientCurrentTxPowerLevel OBJECT-TYPE
+ SYNTAX Integer32 (1..8)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The TxPowerLevel N currently selected for client
+ to transmit data. It is up to the clients to honor
+ this transmit power setting."
+ ::= { cd11IfClientTxPowerEntry 10 }
+
+
+cd11IfErpOfdmTxPowerTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfErpOfdmTxPowerEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table shows the available ERP-OFDM
+ transmit power levels for radios implementing
+ IEEE 802.11g Protocol and configures one of the
+ levels as the transmit power level.
+
+ This table has a sparse dependent relationship
+ on the ifTable. For each entry in this table,
+ there exists an entry in the ifTable of ifType
+ ieee80211(71) and the corresponding
+ cd11IfPhyMacSpecification is ieee802dot11g(3).
+
+ For all IEEE802.11g radios with an entry in this
+ table, the IEEE802dot11-MIB dot11PhyTxPowerTable
+ will be used to configure ERP-CCK transmit power
+ levels."
+ ::= { cd11IfPhyConfig 14 }
+
+cd11IfErpOfdmTxPowerEntry OBJECT-TYPE
+ SYNTAX Cd11IfErpOfdmTxPowerEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry specifies the number of available
+ transmit power levels, the values of all the
+ levels, and the configured transmit power level
+ for an IEEE 802.11g radio interface."
+ INDEX { ifIndex }
+ ::= { cd11IfErpOfdmTxPowerTable 1 }
+
+Cd11IfErpOfdmTxPowerEntry ::=
+ SEQUENCE {
+ cd11IfErpOfdmNumberTxPowerLevels Integer32,
+ cd11IfErpOfdmTxPowerLevel1 Integer32,
+ cd11IfErpOfdmTxPowerLevel2 Integer32,
+ cd11IfErpOfdmTxPowerLevel3 Integer32,
+ cd11IfErpOfdmTxPowerLevel4 Integer32,
+ cd11IfErpOfdmTxPowerLevel5 Integer32,
+ cd11IfErpOfdmTxPowerLevel6 Integer32,
+ cd11IfErpOfdmTxPowerLevel7 Integer32,
+ cd11IfErpOfdmTxPowerLevel8 Integer32,
+ cd11IfErpOfdmCurrentTxPowerLevel Integer32
+ }
+
+cd11IfErpOfdmNumberTxPowerLevels OBJECT-TYPE
+ SYNTAX Integer32 (1..8)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The number of power levels available for this
+ radio. This attribute can have a value of
+ 1 to 8."
+ ::= { cd11IfErpOfdmTxPowerEntry 1 }
+
+cd11IfErpOfdmTxPowerLevel1 OBJECT-TYPE
+ SYNTAX Integer32 (0..10000)
+ UNITS "mW"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The ERP-OFDM transmit output power for LEVEL1."
+ ::= { cd11IfErpOfdmTxPowerEntry 2 }
+
+cd11IfErpOfdmTxPowerLevel2 OBJECT-TYPE
+ SYNTAX Integer32 (0..10000)
+ UNITS "mW"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The ERP-OFDM transmit output power for LEVEL2."
+ ::= { cd11IfErpOfdmTxPowerEntry 3 }
+
+cd11IfErpOfdmTxPowerLevel3 OBJECT-TYPE
+ SYNTAX Integer32 (0..10000)
+ UNITS "mW"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The ERP-OFDM transmit output power for LEVEL3."
+ ::= { cd11IfErpOfdmTxPowerEntry 4 }
+
+cd11IfErpOfdmTxPowerLevel4 OBJECT-TYPE
+ SYNTAX Integer32 (0..10000)
+ UNITS "mW"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The ERP-OFDM transmit output power for LEVEL4."
+ ::= { cd11IfErpOfdmTxPowerEntry 5 }
+
+cd11IfErpOfdmTxPowerLevel5 OBJECT-TYPE
+ SYNTAX Integer32 (0..10000)
+ UNITS "mW"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The ERP-OFDM transmit output power for LEVEL5."
+ ::= { cd11IfErpOfdmTxPowerEntry 6 }
+
+cd11IfErpOfdmTxPowerLevel6 OBJECT-TYPE
+ SYNTAX Integer32 (0..10000)
+ UNITS "mW"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The ERP-OFDM transmit output power for LEVEL6."
+ ::= { cd11IfErpOfdmTxPowerEntry 7 }
+
+cd11IfErpOfdmTxPowerLevel7 OBJECT-TYPE
+ SYNTAX Integer32 (0..10000)
+ UNITS "mW"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The ERP-OFDM transmit output power for LEVEL7."
+ ::= { cd11IfErpOfdmTxPowerEntry 8 }
+
+cd11IfErpOfdmTxPowerLevel8 OBJECT-TYPE
+ SYNTAX Integer32 (0..10000)
+ UNITS "mW"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The ERP-OFDM transmit output power for LEVEL8."
+ ::= { cd11IfErpOfdmTxPowerEntry 9 }
+
+cd11IfErpOfdmCurrentTxPowerLevel OBJECT-TYPE
+ SYNTAX Integer32 (1..8)
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "The TxPowerLevel N currently configured
+ to transmit data."
+ ::= { cd11IfErpOfdmTxPowerEntry 10 }
+
+
+cd11IfFrequencyBandTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfFrequencyBandEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table identifies the radio frequency
+ (sub)bands supported on the IEEE 802.11 radio
+ interfaces while operating per the regulations
+ imposed by the cd11IfCurrentCarrierSet.
+
+ This table has an expansion dependent relationship
+ on the ifTable. For each entry in this table,
+ there exists at least an entry in the ifTable of
+ ifType ieee80211(71). This table uses the
+ cd11IfRfFrequencyBand as the expansion index.
+
+ All entries in this table are created or deleted
+ only by the agent."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfPhyConfig 15 }
+
+cd11IfFrequencyBandEntry OBJECT-TYPE
+ SYNTAX Cd11IfFrequencyBandEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry defines a supported radio frequency
+ band for an IEEE 802.11 radio interface."
+ INDEX {
+ ifIndex,
+ cd11IfRfFrequencyBand
+ }
+ ::= { cd11IfFrequencyBandTable 1 }
+
+Cd11IfFrequencyBandEntry ::=
+ SEQUENCE {
+ cd11IfRfFrequencyBand Unsigned32,
+ cd11IfRfFrequencyUnits INTEGER,
+ cd11IfRfStartChannelNumber Unsigned32,
+ cd11IfRfEndChannelNumber Unsigned32,
+ cd11IfRfChannelSpacingNumber Unsigned32,
+ cd11IfRfStartChannelFrequency Unsigned32,
+ cd11IfRfFrequencySpacing Unsigned32,
+ cd11IfRfFrequencyBandType
+ CDot11RadioFrequencyBandType,
+ cd11IfMaxChannelSwitchTime Unsigned32
+ }
+
+cd11IfRfFrequencyBand OBJECT-TYPE
+ SYNTAX Unsigned32
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This object identifies radio frequency bands
+ supported on the radio."
+ ::= { cd11IfFrequencyBandEntry 1 }
+
+cd11IfRfFrequencyUnits OBJECT-TYPE
+ SYNTAX INTEGER {
+ mHz(1)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This base frequency units combines with the
+ cd11IfRfStartChannelFrequency to define the
+ actual frequency of the channel and combines
+ with the cd11IfRfFrequencySpacing to define the
+ minimum frequency spacing between two adjacent
+ frequency channels.
+
+ For example, frequency spacing of 5 MHz is
+ 'mHz' in cd11IfRfFrequencyUnits and 5 in
+ cd11IfRfFrequencySpacing."
+ DEFVAL { mHz }
+ ::= { cd11IfFrequencyBandEntry 2 }
+
+cd11IfRfStartChannelNumber OBJECT-TYPE
+ SYNTAX Unsigned32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Numeric identifier of the first channel supported
+ in this radio frequency band. For example,
+ currently at the 2.4 GHz ISM band, the first channel
+ number is 1, while for the U-NII-1 band in the FCC
+ regulatory domain, the first supported channel is
+ number 36 at frequency 5180 MHz."
+ ::= { cd11IfFrequencyBandEntry 3 }
+
+cd11IfRfEndChannelNumber OBJECT-TYPE
+ SYNTAX Unsigned32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Numeric identifier of the last channel supported
+ in this radio frequency band. For example, in the
+ FCC regulatory domain, the last channel of the 2.4
+ GHz ISM band is number 11 and the last channel of
+ the U-NII-1 band is number 48 at frequency 5240 MHz."
+ ::= { cd11IfFrequencyBandEntry 4 }
+
+cd11IfRfChannelSpacingNumber OBJECT-TYPE
+ SYNTAX Unsigned32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Numeric spacing between the identifiers of two
+ adjacent supported channels in this band. For
+ example, currently at the 2.4 GHz ISM band, the
+ numeric channel spacing is 1, resulting in a channel
+ identifier sequence of 1, 2, 3, etc. In the
+ U-NII-1 band, the numeric channel spacing is 4,
+ resulting in a channel identifier sequence
+ of 36, 40, 44, etc."
+ ::= { cd11IfFrequencyBandEntry 5 }
+
+cd11IfRfStartChannelFrequency OBJECT-TYPE
+ SYNTAX Unsigned32 (0..10000)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This is the base channel frequency of the
+ cd11IfRfStartChannelNumber channel from which
+ subsequent channels of this frequency band are
+ defined. The actual frequency value is defined
+ and calculated by multiplying this object with the
+ cd11IfRfFrequencyUnits. The subsequent channels
+ in the band are calculated by adding the
+ cd11IfRfChannelSpacingNumber multiplied by the
+ cd11IfRfFrequencySpacing to this object value.
+
+ For example, the first channel of U-NII-1 band is
+ channel 36, the cd11IfRfFrequencyUnits is 'mHz',
+ the cd11IfRfStartChannelFrequency is '5180', and
+ the cd11IfRfChannelSpacingNumber is 4. If the
+ cd11IfRfFrequencySpacing is 5 MHz, the second
+ supported channel of the U-NII-1 band will be
+ channel 40 at frequency 5200 MHz."
+ ::= { cd11IfFrequencyBandEntry 6 }
+
+cd11IfRfFrequencySpacing OBJECT-TYPE
+ SYNTAX Unsigned32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This is the frequency separation between two
+ adjacent radio frequency channels. The actual
+ frequency value is calculated by multiplying this
+ object with the cd11IfRfFrequencyUnits. For
+ example, for a frequency spacing of 5 MHz, the
+ value of cd11IfRfFrequencyUnits is 'mHz' and
+ the value of this object is 5."
+ ::= { cd11IfFrequencyBandEntry 7 }
+
+cd11IfRfFrequencyBandType OBJECT-TYPE
+ SYNTAX CDot11RadioFrequencyBandType
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This is the enumerated radio frequency band name(s)
+ which this (sub)band occupies.
+
+ If the frequency band defined in a table row is not
+ included in the current CDot11RadioFrequencyBandType
+ definition, none of the bits are set for this object."
+ ::= { cd11IfFrequencyBandEntry 8 }
+
+cd11IfMaxChannelSwitchTime OBJECT-TYPE
+ SYNTAX Unsigned32
+ UNITS "milliseconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The maximum time required for the radio interface
+ to switch its transceiver from one channel to any
+ other supported channel in any supported band."
+ ::= { cd11IfFrequencyBandEntry 9 }
+
+
+cd11IfNativeTxPowerSupportTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfNativeTxPowerSupportEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table shows the transmit powers supported for
+ all the radio frequency bands on the IEEE 802.11
+ radios.
+
+ This table has an expansion dependent relationship
+ on the ifTable. For each entry in this table,
+ there exists at least an entry in the ifTable of
+ ifType ieee80211(71). This table uses the
+ cd11IfRfFrequencyBand of cd11IfFrequencyBandTable,
+ cd11IfRadioModulationClass, and
+ cd11IfNativeTxPowerLevel as the expansion indices.
+
+ All entries in this table can only be created or
+ deleted by the agent."
+ ::= { cd11IfPhyConfig 16 }
+
+cd11IfNativeTxPowerSupportEntry OBJECT-TYPE
+ SYNTAX Cd11IfNativeTxPowerSupportEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry specifies a supported transmit power
+ level for a frequency band, with a specified
+ modulation technique, on the IEEE 802.11 radio
+ interface."
+ INDEX {
+ ifIndex,
+ cd11IfRfFrequencyBand,
+ cd11IfRadioModulationClass,
+ cd11IfNativeTxPowerLevel
+ }
+ ::= { cd11IfNativeTxPowerSupportTable 1 }
+
+Cd11IfNativeTxPowerSupportEntry ::=
+ SEQUENCE {
+ cd11IfRadioModulationClass CDot11RadioModulationClass,
+ cd11IfNativeTxPowerLevel Unsigned32,
+ cd11IfNativeTxPower Integer32
+ }
+
+cd11IfRadioModulationClass OBJECT-TYPE
+ SYNTAX CDot11RadioModulationClass
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This identifies a radio modulation technique
+ used by the 802.11 radio interface."
+ ::= { cd11IfNativeTxPowerSupportEntry 1 }
+
+
+cd11IfNativeTxPowerLevel OBJECT-TYPE
+ SYNTAX Unsigned32
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This is the unique index for a transmit power of a
+ radio frequency band for the radio."
+ ::= { cd11IfNativeTxPowerSupportEntry 2 }
+
+cd11IfNativeTxPower OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This is a transmit power available at a radio
+ frequency band for the radio, when using the
+ modulation technique specified by the
+ cd11IfRadioModulationClass. The value of the
+ cd11IfNativeTxPowerUnits defines the units of this
+ transmit power. The value can be negative if the
+ units is 'dBm'."
+ ::= { cd11IfNativeTxPowerSupportEntry 3 }
+
+
+cd11IfRfNativePowerTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfRfNativePowerEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table configures the radio power settings
+ for frequency bands supported on the IEEE 802.11
+ radios. This table serves as an alternative for
+ the IEEE802dot11-MIB dot11PhyTxPowerTable. This
+ table allows different transmit powers to be used
+ on different radio frequency bands.
+
+ This table has an expansion dependent relationship
+ on the ifTable. For each entry in this table,
+ there exists at least an entry in the ifTable of
+ ifType ieee80211(71). This table uses the
+ cd11IfRfFrequencyBand and cd11IfRadioModulationClass
+ as the expansion indices.
+
+ All entries in this table are created or deleted
+ only by the agent."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfPhyConfig 17 }
+
+cd11IfRfNativePowerEntry OBJECT-TYPE
+ SYNTAX Cd11IfRfNativePowerEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry specifies the transmit power
+ settings of a particular radio frequency band,
+ with a specified modulation technique, for
+ an IEEE 802.11 radio interface."
+ INDEX {
+ ifIndex,
+ cd11IfRfFrequencyBand,
+ cd11IfRadioModulationClass
+ }
+ ::= { cd11IfRfNativePowerTable 1 }
+
+Cd11IfRfNativePowerEntry ::=
+ SEQUENCE {
+ cd11IfNativeNumberPowerLevels Unsigned32,
+ cd11IfNativeCurrentPowerLevel Unsigned32,
+ cd11IfNativePowerUnits INTEGER
+ }
+
+cd11IfNativeNumberPowerLevels OBJECT-TYPE
+ SYNTAX Unsigned32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The number of transmit power levels of a radio
+ frequency band for the radio. The value of this
+ object should be the same as the maximum
+ cd11IfNativeTxPowerLevel of the same ifIndex,
+ cd11IfRadioFrequencyBand, and
+ cd11IfRadioModulationClass.
+
+ If the value of this object is 0, the radio can
+ only receive, not transmit, on this frequency
+ band and modulation technique."
+ ::= { cd11IfRfNativePowerEntry 1 }
+
+cd11IfNativeCurrentPowerLevel OBJECT-TYPE
+ SYNTAX Unsigned32
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "If cd11IfPhyNativePowerUseStandard is 'false',
+ this object configures the current transmit power
+ level of a radio frequency band for the radio.
+ The value shall be one of the supported
+ cd11IfNativeTxPowerLevel for the radio of the
+ the same frequency band and modulation technique.
+
+ For any radio does not transmit power in the
+ specified radio frequency band and modulation
+ technique, the value of this object is 0."
+ ::= { cd11IfRfNativePowerEntry 2 }
+
+cd11IfNativePowerUnits OBJECT-TYPE
+ SYNTAX INTEGER {
+ mW(1),
+ dBm(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The native transmit power units implemented on the
+ radio. It is the units for the cd11IfNativeTxPower.
+ For the IEEE802dot11-MIB dot11PhyTxPowerTable,
+ 'mW' is the only supported units."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ DEFVAL { mW }
+ ::= { cd11IfRfNativePowerEntry 3 }
+
+
+cd11IfDataRatesSensitivityTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfDataRatesSensitivityEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table specifies the receive sensitivity
+ specifications of IEEE 802.11 radio interfaces.
+
+ This table has an expansion dependent relationship
+ on the ifTable. For each entry in this table,
+ there exists at least an entry in the ifTable of
+ ifType ieee80211(71). This table uses the
+ cd11IfRadioModulationClass and IEEE802dot11-MIB
+ dot11SupportedDataRatesRxIndex as the expansion
+ indices.
+
+ Entries in this table cannot be created or deleted
+ by the network management system. All entries are
+ created or deleted by the agent."
+ ::= { cd11IfPhyConfig 18 }
+
+cd11IfDataRatesSensitivityEntry OBJECT-TYPE
+ SYNTAX Cd11IfDataRatesSensitivityEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry specifies the receive sensitivity of an
+ IEEE 802.11 radio interface, with a specified
+ modulation technique, for each supported data
+ rate identified by the dot11SupportedDataRatesRxIndex."
+ INDEX {
+ ifIndex,
+ cd11IfRadioModulationClass,
+ dot11SupportedDataRatesRxIndex
+ }
+ ::= { cd11IfDataRatesSensitivityTable 1 }
+
+Cd11IfDataRatesSensitivityEntry ::=
+ SEQUENCE {
+ cd11IfRatesSensRequiredSnr Integer32,
+ cd11IfRatesSensContention Integer32
+ }
+
+cd11IfRatesSensRequiredSnr OBJECT-TYPE
+ SYNTAX Integer32
+ UNITS "dB"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The minimum SNR requirement for each data rate
+ supported by a radio interface, when using the
+ modulation technique specified by
+ cd11IfRadioModulationClass. This is the required
+ carrier to noise difference."
+ ::= { cd11IfDataRatesSensitivityEntry 1 }
+
+cd11IfRatesSensContention OBJECT-TYPE
+ SYNTAX Integer32
+ UNITS "dBm"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The average contention sensitivity level for each
+ data rate supported by a radio interface, when using
+ the modulation technique specified by
+ cd11IfRadioModulationClass. This is the value where
+ 50% of the packets are received successfully."
+ ::= { cd11IfDataRatesSensitivityEntry 2 }
+
+
+-- Statistics Objects
+
+cd11IfMacLayerCountersTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfMacLayerCountersEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table includes MAC layer statistics collected
+ by the IEEE 802.11 radio interface. This table has
+ a sparse dependent relationship on the ifTable.
+ For each entry in this table, there exists an entry
+ in the ifTable of ifType ieee80211(71)."
+ ::= { cd11IfMacStatistics 1 }
+
+cd11IfMacLayerCountersEntry OBJECT-TYPE
+ SYNTAX Cd11IfMacLayerCountersEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry contains counters of frame transmissions
+ for a radio interface."
+ INDEX { ifIndex }
+ ::= { cd11IfMacLayerCountersTable 1 }
+
+Cd11IfMacLayerCountersEntry ::=
+ SEQUENCE {
+ cd11IfTransDeferEnerDetects Counter32,
+ cd11IfRecFrameMacCrcErrors Counter32,
+ cd11IfSsidMismatches Counter32
+ }
+
+cd11IfTransDeferEnerDetects OBJECT-TYPE
+ SYNTAX Counter32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This counter shall increment when a frame transmission
+ is deferred due to energy detection."
+ ::= { cd11IfMacLayerCountersEntry 1 }
+
+cd11IfRecFrameMacCrcErrors OBJECT-TYPE
+ SYNTAX Counter32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This counter shall increment when a frame received has
+ any MAC CRC error."
+ ::= { cd11IfMacLayerCountersEntry 2 }
+
+cd11IfSsidMismatches OBJECT-TYPE
+ SYNTAX Counter32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This counter shall increment when a beacon or probe
+ response frame received for which the SSIDs in the
+ frame do not match the IEEE802dot11-MIB
+ dot11DesiredSSID object."
+ REFERENCE
+ "IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
+ Access Control and Physical Layer Specifications,
+ LAN MAN Standards Committee of the IEEE Computer
+ Society, IEEE802dot11-MIB."
+ ::= { cd11IfMacLayerCountersEntry 3 }
+
+
+cd11IfRogueApDetectedTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Cd11IfRogueApDetectedEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table includes rogue AP detected
+ information collected by the IEEE 802.11 radio
+ interface and 802.11 system management. This
+ table has a sparse dependent relationship on
+ the ifTable. For each entry in this table,
+ there exists an entry in the ifTable of ifType
+ ieee80211(71)."
+ ::= { cd11IfMacStatistics 2 }
+
+cd11IfRogueApDetectedEntry OBJECT-TYPE
+ SYNTAX Cd11IfRogueApDetectedEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry contains information of a rogue AP
+ detected by a radio interface."
+ INDEX {
+ ifIndex,
+ cd11IfRogueApMacAddr
+ }
+ ::= { cd11IfRogueApDetectedTable 1 }
+
+Cd11IfRogueApDetectedEntry ::=
+ SEQUENCE {
+ cd11IfRogueApMacAddr MacAddress,
+ cd11IfRogueApName SnmpAdminString
+ }
+
+cd11IfRogueApMacAddr OBJECT-TYPE
+ SYNTAX MacAddress
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This is the MAC address of a rogue access point
+ detected by this radio."
+ ::= { cd11IfRogueApDetectedEntry 1 }
+
+cd11IfRogueApName OBJECT-TYPE
+ SYNTAX SnmpAdminString
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This is the name of the rogue access point."
+ ::= { cd11IfRogueApDetectedEntry 2 }
+
+
+-- ********************************************************************
+-- * Notifications
+-- ********************************************************************
+
+cd11IfStationSwitchOverNotif NOTIFICATION-TYPE
+ OBJECTS {
+ cd11IfLocalRadioMonitorStatus
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification will be sent when a radio
+ interface changes the cd11IfLocalRadioMonitorStatus
+ from 'monitor' to 'active'."
+ ::= { ciscoDot11IfMIBNotifications 1 }
+
+cd11IfRogueApDetectedNotif NOTIFICATION-TYPE
+ OBJECTS {
+ cd11IfRogueApName
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification will be sent when a radio
+ interface detects a new rogue AP and causes
+ a new row to be added to the
+ cd11IfRogueApDetectedTable."
+ ::= { ciscoDot11IfMIBNotifications 2 }
+
+
+-- ********************************************************************
+-- * Conformance information
+-- ********************************************************************
+
+
+ciscoDot11IfMIBConformance
+ OBJECT IDENTIFIER ::= { ciscoDot11IfMIB 3 }
+ciscoDot11IfMIBCompliances
+ OBJECT IDENTIFIER ::= { ciscoDot11IfMIBConformance 1 }
+ciscoDot11IfMIBGroups
+ OBJECT IDENTIFIER ::= { ciscoDot11IfMIBConformance 2 }
+
+
+-- *****************************************************************
+-- Compliance statements
+-- *****************************************************************
+
+ciscoDot11IfCompliance MODULE-COMPLIANCE
+ STATUS deprecated
+ DESCRIPTION
+ "The compliance statement for the cd11IfManagement,
+ cd11IfPhyConfig, cd11IfMacStatisticsGroup, and
+ cd11IfDomainCapabilityGroup groups."
+ MODULE
+ MANDATORY-GROUPS {
+ cd11IfManagementGroup,
+ cd11IfPhyConfigGroup,
+ cd11IfMacStatisticsGroup,
+ cd11IfDomainCapabilityGroup
+ }
+
+ OBJECT cd11IfVlanEncryptKeyStatus
+ DESCRIPTION
+ "Creation of rows must be done via
+ 'createAndGo' for all keys. When the
+ agent successfully creates the encryption
+ key, this object is set to 'active' by the
+ agent."
+
+ GROUP cd11IfVlanEncryptKeyConfigGroup
+ DESCRIPTION
+ "This group is required only if different
+ WEP keys are configured for the same VLAN
+ on different IEEE 802.11 radio interfaces.
+ The CISCO-WLAN-VLAN-MIB cwvlWlanNUcastKeyTable
+ should be used otherwise."
+ ::= { ciscoDot11IfMIBCompliances 1 }
+
+ciscoDot11IfComplianceRev1 MODULE-COMPLIANCE
+ STATUS deprecated
+ DESCRIPTION
+ "The compliance statement of the ciscoDot11IfMIB
+ module."
+ MODULE
+ MANDATORY-GROUPS {
+ cd11IfRadioManageGroup,
+ cd11IfAssociationManageGroup,
+ cd11IfPhyConfigGroupRev1,
+ cd11IfMacStatisticsGroup
+ }
+
+ GROUP cd11IfSsidAssociationGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing this MIB does not support
+ CISCO-DOT11-SSID-SECURITY-MIB."
+
+ GROUP cd11IfVlanManageGroup
+ DESCRIPTION
+ "This group is required only if different
+ WEP keys are configured for the same VLAN
+ on different IEEE 802.11 radio interfaces
+ or if the CISCO-WLAN-VLAN-MIB is not
+ supported on the platform implementing
+ this MIB."
+
+ GROUP cd11IfRemoteMonitoringGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing this MIB does not support
+ CISCO-L2-DEV-MONITORING-MIB."
+
+ GROUP cd11IfPhyErpConfigGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing IEEE 802.11g Protocol."
+
+ OBJECT cd11IfVlanEncryptKeyStatus
+ DESCRIPTION
+ "Creation of rows must be done via
+ 'createAndGo' for all keys. When the
+ agent successfully creates the encryption
+ key, this object is set to 'active' by the
+ agent."
+
+ OBJECT cd11IfPhyFhssMaxCompatibleRate
+ DESCRIPTION
+ "This object is only mandatory for devices
+ supporting Frequency-Hopping Spread Spectrum."
+ ::= { ciscoDot11IfMIBCompliances 2 }
+
+ciscoDot11IfComplianceRev2 MODULE-COMPLIANCE
+ STATUS deprecated
+ DESCRIPTION
+ "The compliance statement of the ciscoDot11IfMIB
+ module."
+ MODULE
+ MANDATORY-GROUPS {
+ cd11IfStationManageGroup,
+ cd11IfAssociationManageGroup,
+ cd11IfPhyConfigGroupRev1,
+ cd11IfMacStatisticsGroup,
+ cd11IfNativeRadioManageGroup,
+ cd11IfDataRatesSensitivityGroup
+ }
+
+ GROUP cd11IfSsidAssociationGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing this MIB does not support
+ CISCO-DOT11-SSID-SECURITY-MIB."
+
+ GROUP cd11IfVlanManageGroup
+ DESCRIPTION
+ "This group is required only if different
+ encryption cipher types are configured for
+ the same VLAN on different IEEE 802.11 radio
+ interfaces or if the CISCO-WLAN-VLAN-MIB is
+ not supported on the platform implementing
+ this MIB."
+
+ GROUP cd11IfVlanWepManageGroup
+ DESCRIPTION
+ "This group is required only if different
+ WEP keys are configured for the same VLAN
+ on different IEEE 802.11 radio interfaces
+ or if the CISCO-WLAN-VLAN-MIB is not
+ supported on the platform implementing
+ this MIB."
+
+ GROUP cd11IfRemoteMonitoringGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing this MIB does not support
+ CISCO-L2-DEV-MONITORING-MIB."
+
+ GROUP cd11IfPhyErpConfigGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing IEEE 802.11g Protocol."
+
+ GROUP cd11IfRogueApDetectedGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing this MIB does not support
+ ciscoDdpIappRogueApInfoGroup objects in
+ CISCO-DDP-IAPP-MIB."
+
+ GROUP cd11IfMonitorNotificationGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing this MIB does not support
+ CISCO-DDP-IAPP-MIB ciscoDdpIappNotificationGroup
+ and CISCO-L2-DEV-MONITORING-MIB
+ ciscoL2DevMonNotificationGroup."
+
+ OBJECT cd11IfVlanEncryptKeyStatus
+ DESCRIPTION
+ "Creation of rows must be done via
+ 'createAndGo' for all keys. When the
+ agent successfully creates the encryption
+ key, this object is set to 'active' by the
+ agent."
+
+ OBJECT cd11IfPhyFhssMaxCompatibleRate
+ DESCRIPTION
+ "This object is only mandatory for devices
+ supporting Frequency-Hopping Spread Spectrum."
+ ::= { ciscoDot11IfMIBCompliances 3 }
+
+ciscoDot11IfComplianceRev3 MODULE-COMPLIANCE
+ STATUS deprecated
+ DESCRIPTION
+ "The compliance statement of the ciscoDot11IfMIB
+ module."
+ MODULE
+ MANDATORY-GROUPS {
+ cd11IfStationManageGroup,
+ cd11IfAssociationManageGroup,
+ cd11IfPhyConfigGroupRev1,
+ cd11IfMacStatisticsGroup,
+ cd11IfNativeRadioManageGroup,
+ cd11IfDataRatesSensitivityGroup,
+ cd11Ifdot11UpgradeStatusGroup
+ }
+
+ GROUP cd11IfSsidAssociationGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing this MIB does not support
+ CISCO-DOT11-SSID-SECURITY-MIB."
+
+ GROUP cd11IfVlanManageGroup
+ DESCRIPTION
+ "This group is required only if different
+ encryption cipher types are configured for
+ the same VLAN on different IEEE 802.11 radio
+ interfaces or if the CISCO-WLAN-VLAN-MIB is
+ not supported on the platform implementing
+ this MIB."
+
+ GROUP cd11IfVlanWepManageGroup
+ DESCRIPTION
+ "This group is required only if different
+ WEP keys are configured for the same VLAN
+ on different IEEE 802.11 radio interfaces
+ or if the CISCO-WLAN-VLAN-MIB is not
+ supported on the platform implementing
+ this MIB."
+
+ GROUP cd11IfRemoteMonitoringGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing this MIB does not support
+ CISCO-L2-DEV-MONITORING-MIB."
+
+ GROUP cd11IfPhyErpConfigGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing IEEE 802.11g Protocol."
+
+ GROUP cd11IfRogueApDetectedGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing this MIB does not support
+ ciscoDdpIappRogueApInfoGroup objects in
+ CISCO-DDP-IAPP-MIB."
+
+ GROUP cd11IfMonitorNotificationGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing this MIB does not support
+ CISCO-DDP-IAPP-MIB ciscoDdpIappNotificationGroup
+ and CISCO-L2-DEV-MONITORING-MIB
+ ciscoL2DevMonNotificationGroup."
+
+ OBJECT cd11IfVlanEncryptKeyStatus
+ DESCRIPTION
+ "Creation of rows must be done via
+ 'createAndGo' for all keys. When the
+ agent successfully creates the encryption
+ key, this object is set to 'active' by the
+ agent."
+
+ OBJECT cd11IfPhyFhssMaxCompatibleRate
+ DESCRIPTION
+ "This object is only mandatory for devices
+ supporting Frequency-Hopping Spread Spectrum."
+ ::= { ciscoDot11IfMIBCompliances 4 }
+
+ciscoDot11IfComplianceRev4 MODULE-COMPLIANCE
+ STATUS current
+ DESCRIPTION
+ "The compliance statement of the ciscoDot11IfMIB
+ module."
+ MODULE
+ MANDATORY-GROUPS {
+ cd11IfStationManageGroup,
+ cd11IfAssociationManageGroup,
+ cd11IfPhyConfigGroupRev1,
+ cd11IfMacStatisticsGroup,
+ cd11IfNativeRadioManageGroup,
+ cd11IfDataRatesSensitivityGroup,
+ cd11Ifdot11UpgradeStatusGroup,
+ cd11Ifdot11MobileStationScanGroup
+ }
+
+ GROUP cd11IfSsidAssociationGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing this MIB does not support
+ CISCO-DOT11-SSID-SECURITY-MIB."
+
+ GROUP cd11IfVlanManageGroup
+ DESCRIPTION
+ "This group is required only if different
+ encryption cipher types are configured for
+ the same VLAN on different IEEE 802.11 radio
+ interfaces or if the CISCO-WLAN-VLAN-MIB is
+ not supported on the platform implementing
+ this MIB."
+
+ GROUP cd11IfVlanWepManageGroup
+ DESCRIPTION
+ "This group is required only if different
+ WEP keys are configured for the same VLAN
+ on different IEEE 802.11 radio interfaces
+ or if the CISCO-WLAN-VLAN-MIB is not
+ supported on the platform implementing
+ this MIB."
+
+ GROUP cd11IfRemoteMonitoringGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing this MIB does not support
+ CISCO-L2-DEV-MONITORING-MIB."
+
+ GROUP cd11IfPhyErpConfigGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing IEEE 802.11g Protocol."
+
+ GROUP cd11IfRogueApDetectedGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing this MIB does not support
+ ciscoDdpIappRogueApInfoGroup objects in
+ CISCO-DDP-IAPP-MIB."
+
+ GROUP cd11IfMonitorNotificationGroup
+ DESCRIPTION
+ "This group is required only if the platform
+ implementing this MIB does not support
+ CISCO-DDP-IAPP-MIB ciscoDdpIappNotificationGroup
+ and CISCO-L2-DEV-MONITORING-MIB
+ ciscoL2DevMonNotificationGroup."
+
+ OBJECT cd11IfVlanEncryptKeyStatus
+ DESCRIPTION
+ "Creation of rows must be done via
+ 'createAndGo' for all keys. When the
+ agent successfully creates the encryption
+ key, this object is set to 'active' by the
+ agent."
+
+ OBJECT cd11IfPhyFhssMaxCompatibleRate
+ DESCRIPTION
+ "This object is only mandatory for devices
+ supporting Frequency-Hopping Spread Spectrum."
+ ::= { ciscoDot11IfMIBCompliances 5 }
+
+-- *****************************************************************
+-- Units of conformance
+-- *****************************************************************
+
+cd11IfManagementGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfStationRole,
+ cd11IfCiscoExtensionsEnable,
+ cd11IfAllowBroadcastSsidAssoc,
+ cd11IfPrivacyOptionMaxRate,
+ cd11IfEthernetEncapsulDefault,
+ cd11IfBridgeSpacing,
+ cd11IfDesiredSsidMaxAssocSta,
+ cd11IfAuxiliarySsidLength,
+ cd11IfVoipExtensionsEnable,
+ cd11IfDesiredSsidMicAlgorithm,
+ cd11IfDesiredSsidWepPermuteAlg,
+ cd11IfAuthAlgRequireEap,
+ cd11IfAuthAlgRequireMacAddr,
+ cd11IfAuthAlgDefaultVlan,
+ cd11IfWepDefaultKeyLen,
+ cd11IfWepDefaultKeyValue,
+ cd11IfDesiredBssAddr,
+ cd11IfAuxSsid,
+ cd11IfAuxSsidBroadcastSsid,
+ cd11IfAuxSsidMaxAssocSta,
+ cd11IfAuxSsidMicAlgorithm,
+ cd11IfAuxSsidWepPermuteAlg,
+ cd11IfAuxSsidAuthAlgEnable,
+ cd11IfAuxSsidAuthAlgRequireEap,
+ cd11IfAuxSsidAuthAlgRequireMac,
+ cd11IfAuxSsidAuthAlgDefaultVlan,
+ cd11IfAssignedSta
+ }
+ STATUS deprecated
+ DESCRIPTION
+ "Information to support management of
+ IEEE 802.11 protocol interfaces."
+ ::= { ciscoDot11IfMIBGroups 1 }
+
+
+cd11IfPhyConfigGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfCurrentCarrierSet,
+ cd11IfModulationType,
+ cd11IfPreambleType,
+ cd11IfPhyFhssMaxCompatibleRate,
+ cd11IfPhyDsssMaxCompatibleRate,
+ cd11IfPhyDsssChannelAutoEnable,
+ cd11IfPhyDsssCurrentChannel,
+ cd11IfSuppDataRatesPrivacyValue,
+ cd11IfSuppDataRatesPrivacyEnabl,
+ cd11IfChanSelectEnable
+ }
+ STATUS deprecated
+ DESCRIPTION
+ "Information to support configuration of
+ IEEE 802.11 protocol Physical layer."
+ ::= { ciscoDot11IfMIBGroups 2 }
+
+
+cd11IfMacStatisticsGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfTransDeferEnerDetects,
+ cd11IfRecFrameMacCrcErrors,
+ cd11IfSsidMismatches
+ }
+ STATUS current
+ DESCRIPTION
+ "Statistics information on IEEE 802.11
+ radio interface MAC layer."
+ ::= { ciscoDot11IfMIBGroups 3 }
+
+
+cd11IfVlanEncryptKeyConfigGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfVlanEncryptKeyLen,
+ cd11IfVlanEncryptKeyValue,
+ cd11IfVlanEncryptKeyStatus
+ }
+ STATUS deprecated
+ DESCRIPTION
+ "WEP key configuration for specific VLANs
+ on IEEE 802.11 radio interface."
+ ::= { ciscoDot11IfMIBGroups 4 }
+
+
+cd11IfDomainCapabilityGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfDomainCapabilitySet
+ }
+ STATUS deprecated
+ DESCRIPTION
+ "This object class provides the objects necessary
+ to manage the channels and transmit power usable by
+ a radio within its regulatory domain."
+ ::= { ciscoDot11IfMIBGroups 5 }
+
+
+cd11IfPhyMacCapabilityGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfPhyBasicRateSet,
+ cd11IfPhyMacSpecification
+ }
+ STATUS deprecated
+ DESCRIPTION
+ "This object class provides the objects necessary
+ to manage the Basic Rate capability applied to the
+ defined operational data rate and and IEEE 802.11
+ Standard applied to the radio."
+ ::= { ciscoDot11IfMIBGroups 6 }
+
+cd11IfAuthAlgMethodListGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfAuthAlgEapMethod,
+ cd11IfAuthAlgMacAddrMethod,
+ cd11IfAuxSsidAuthAlgEapMethod,
+ cd11IfAuxSsidAuthAlgMacMethod
+ }
+ STATUS deprecated
+ DESCRIPTION
+ "This object class provides the objects necessary
+ to specify the authentication method applied to
+ MAC address or EAP authentications."
+ ::= { ciscoDot11IfMIBGroups 7 }
+
+
+cd11IfRadioManageGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfStationRole,
+ cd11IfCiscoExtensionsEnable,
+ cd11IfPrivacyOptionMaxRate,
+ cd11IfEthernetEncapsulDefault,
+ cd11IfBridgeSpacing,
+ cd11IfVoipExtensionsEnable,
+ cd11IfAuxiliarySsidLength,
+ cd11IfAllowBroadcastSsidAssoc,
+ cd11IfDesiredBssAddr,
+ cd11IfAssignedSta,
+ cd11IfWorldMode,
+ cd11IfWorldModeCountry,
+ cd11IfMobileStationScanParent
+ }
+ STATUS deprecated
+ DESCRIPTION
+ "Information to manage IEEE 802.11 protocol
+ radio interface settings."
+ ::= { ciscoDot11IfMIBGroups 8 }
+
+
+cd11IfAssociationManageGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfDesiredSsidMaxAssocSta,
+ cd11IfDesiredSsidMicAlgorithm,
+ cd11IfDesiredSsidWepPermuteAlg,
+ cd11IfAuthAlgRequireEap,
+ cd11IfAuthAlgRequireMacAddr,
+ cd11IfAuthAlgDefaultVlan,
+ cd11IfAuthAlgEapMethod,
+ cd11IfAuthAlgMacAddrMethod,
+ cd11IfWepDefaultKeyLen,
+ cd11IfWepDefaultKeyValue
+ }
+ STATUS current
+ DESCRIPTION
+ "Information to manage IEEE 802.11 protocol
+ interface desired SSID association and
+ default encryption key settings."
+ ::= { ciscoDot11IfMIBGroups 9 }
+
+cd11IfSsidAssociationGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfAuxSsid,
+ cd11IfAuxSsidBroadcastSsid,
+ cd11IfAuxSsidMaxAssocSta,
+ cd11IfAuxSsidMicAlgorithm,
+ cd11IfAuxSsidWepPermuteAlg,
+ cd11IfAuxSsidAuthAlgEnable,
+ cd11IfAuxSsidAuthAlgRequireEap,
+ cd11IfAuxSsidAuthAlgRequireMac,
+ cd11IfAuxSsidAuthAlgDefaultVlan,
+ cd11IfAuxSsidAuthAlgEapMethod,
+ cd11IfAuxSsidAuthAlgMacMethod
+ }
+ STATUS current
+ DESCRIPTION
+ "Information to manage IEEE 802.11 protocol
+ interface SSID association and authentication
+ settings."
+ ::= { ciscoDot11IfMIBGroups 10 }
+
+
+cd11IfVlanManageGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfVlanEncryptKeyLen,
+ cd11IfVlanEncryptKeyValue,
+ cd11IfVlanEncryptKeyStatus,
+ cd11IfVlanEncryptKeyTransmit,
+ cd11IfVlanSecurityVlanEnabled,
+ cd11IfVlanBcastKeyChangeInterval,
+ cd11IfVlanBcastKeyCapabilChange,
+ cd11IfVlanBcastKeyClientLeave,
+ cd11IfVlanSecurityCiphers,
+ cd11IfVlanSecurityRowStatus
+ }
+ STATUS current
+ DESCRIPTION
+ "Information to manage IEEE 802.11 protocol
+ interface VLAN and encryption settings."
+ ::= { ciscoDot11IfMIBGroups 11 }
+
+
+cd11IfRemoteMonitoringGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfRadioMonitorPollingFreq,
+ cd11IfRadioMonitorPollingTimeOut,
+ cd11IfLocalRadioMonitorStatus,
+ cd11IfRadioMonitorRowStatus
+ }
+ STATUS current
+ DESCRIPTION
+ "Information to manage IEEE 802.11 protocol
+ interface remote radio monitoring settings."
+ ::= { ciscoDot11IfMIBGroups 12 }
+
+
+cd11IfPhyConfigGroupRev1 OBJECT-GROUP
+ OBJECTS {
+ cd11IfCurrentCarrierSet,
+ cd11IfModulationType,
+ cd11IfPreambleType,
+ cd11IfDomainCapabilitySet,
+ cd11IfPhyBasicRateSet,
+ cd11IfPhyMacSpecification,
+ cd11IfPhyConcatenation,
+ cd11IfPhyDsssMaxCompatibleRate,
+ cd11IfPhyDsssChannelAutoEnable,
+ cd11IfPhyDsssCurrentChannel,
+ cd11IfPhyFhssMaxCompatibleRate,
+ cd11IfSuppDataRatesPrivacyValue,
+ cd11IfSuppDataRatesPrivacyEnabl,
+ cd11IfChanSelectEnable,
+ cd11IfClientNumberTxPowerLevels,
+ cd11IfClientTxPowerLevel1,
+ cd11IfClientTxPowerLevel2,
+ cd11IfClientTxPowerLevel3,
+ cd11IfClientTxPowerLevel4,
+ cd11IfClientTxPowerLevel5,
+ cd11IfClientTxPowerLevel6,
+ cd11IfClientTxPowerLevel7,
+ cd11IfClientTxPowerLevel8,
+ cd11IfClientCurrentTxPowerLevel
+ }
+ STATUS current
+ DESCRIPTION
+ "Information to configure IEEE 802.11 protocol
+ Physical layer settings."
+ ::= { ciscoDot11IfMIBGroups 13 }
+
+cd11IfPhyErpConfigGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfErpOfdmNumberTxPowerLevels,
+ cd11IfErpOfdmTxPowerLevel1,
+ cd11IfErpOfdmTxPowerLevel2,
+ cd11IfErpOfdmTxPowerLevel3,
+ cd11IfErpOfdmTxPowerLevel4,
+ cd11IfErpOfdmTxPowerLevel5,
+ cd11IfErpOfdmTxPowerLevel6,
+ cd11IfErpOfdmTxPowerLevel7,
+ cd11IfErpOfdmTxPowerLevel8,
+ cd11IfErpOfdmCurrentTxPowerLevel
+ }
+ STATUS current
+ DESCRIPTION
+ "Information to configure IEEE 802.11g protocol
+ Physical layer settings."
+ ::= { ciscoDot11IfMIBGroups 14 }
+
+cd11IfVlanWepManageGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfVlanEncryptionMode,
+ cd11IfVlanWepEncryptOptions,
+ cd11IfVlanWepEncryptMic,
+ cd11IfVlanWepEncryptKeyHashing
+ }
+ STATUS current
+ DESCRIPTION
+ "Information to manage IEEE 802.11 protocol
+ interface VLAN WEP encryption settings."
+ ::= { ciscoDot11IfMIBGroups 15 }
+
+cd11IfRogueApDetectedGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfRogueApName
+ }
+ STATUS current
+ DESCRIPTION
+ "Rogue AP detection information."
+ ::= { ciscoDot11IfMIBGroups 16 }
+
+
+cd11IfStationManageGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfStationRole,
+ cd11IfCiscoExtensionsEnable,
+ cd11IfPrivacyOptionMaxRate,
+ cd11IfEthernetEncapsulDefault,
+ cd11IfBridgeSpacing,
+ cd11IfVoipExtensionsEnable,
+ cd11IfAuxiliarySsidLength,
+ cd11IfAllowBroadcastSsidAssoc,
+ cd11IfDesiredBssAddr,
+ cd11IfAssignedSta,
+ cd11IfWorldMode,
+ cd11IfWorldModeCountry,
+ cd11IfMobileStationScanParent,
+ cd11IfPsPacketForwardEnable,
+ cd11IfMultipleBssidEnable,
+ cd11IfVlanPsPacketForwardEnable
+ }
+ STATUS current
+ DESCRIPTION
+ "Information to manage IEEE 802.11 protocol
+ radio interface settings."
+ ::= { ciscoDot11IfMIBGroups 17 }
+
+cd11IfNativeRadioManageGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfPhyNativePowerUseStandard,
+ cd11IfRfFrequencyUnits,
+ cd11IfRfStartChannelNumber,
+ cd11IfRfEndChannelNumber,
+ cd11IfRfChannelSpacingNumber,
+ cd11IfRfStartChannelFrequency,
+ cd11IfRfFrequencySpacing,
+ cd11IfRfFrequencyBandType,
+ cd11IfMaxChannelSwitchTime,
+ cd11IfNativeNumberPowerLevels,
+ cd11IfNativeCurrentPowerLevel,
+ cd11IfNativePowerUnits,
+ cd11IfNativeTxPower
+ }
+ STATUS current
+ DESCRIPTION
+ "Native parameters to manage IEEE 802.11
+ radio power and frequency bands."
+ ::= { ciscoDot11IfMIBGroups 18 }
+
+cd11IfDataRatesSensitivityGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfRatesSensRequiredSnr,
+ cd11IfRatesSensContention
+ }
+ STATUS current
+ DESCRIPTION
+ "Receive sensitivity specification for IEEE
+ 802.11 radios."
+ ::= { ciscoDot11IfMIBGroups 19 }
+
+cd11IfMonitorNotificationGroup NOTIFICATION-GROUP
+ NOTIFICATIONS {
+ cd11IfStationSwitchOverNotif,
+ cd11IfRogueApDetectedNotif
+ }
+ STATUS current
+ DESCRIPTION
+ "The notification group for this module."
+ ::= { ciscoDot11IfMIBGroups 20 }
+
+cd11Ifdot11UpgradeStatusGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfDot11UpgradeStatus
+ }
+ STATUS current
+ DESCRIPTION
+ "This collection of objects provide information
+ about the status of upgrade of the dot11 radios
+ to operate in the new frequency set. "
+ ::= { ciscoDot11IfMIBGroups 21 }
+
+cd11Ifdot11MobileStationScanGroup OBJECT-GROUP
+ OBJECTS {
+ cd11IfMobileStationListIgnore,
+ cd11IfMobileStationScanChannel
+ }
+ STATUS current
+ DESCRIPTION
+ "This collection of objects provide information
+ about the limited channel to scan and Ignore
+ List. "
+ ::= { ciscoDot11IfMIBGroups 22 }
+END
+
generated by cgit v1.2.3 (git 2.46.0) at 2026-02-26 13:23:29 +0000