From 98a672123c7872f6b9b75a9a2b6bb3aea504de6a Mon Sep 17 00:00:00 2001 From: David Leutgeb Date: Tue, 5 Dec 2023 12:25:34 +0100 Subject: Initial commit --- MIBS/junos/JUNIPER-PW-TDM-MIB | 1394 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 1394 insertions(+) create mode 100644 MIBS/junos/JUNIPER-PW-TDM-MIB (limited to 'MIBS/junos/JUNIPER-PW-TDM-MIB') diff --git a/MIBS/junos/JUNIPER-PW-TDM-MIB b/MIBS/junos/JUNIPER-PW-TDM-MIB new file mode 100644 index 0000000..df83c79 --- /dev/null +++ b/MIBS/junos/JUNIPER-PW-TDM-MIB @@ -0,0 +1,1394 @@ + -- extracted from pw-tdm-draft-08 + + JUNIPER-PW-TDM-MIB DEFINITIONS ::= BEGIN + + IMPORTS + MODULE-IDENTITY, OBJECT-TYPE, + Integer32, Counter32, Unsigned32, transmission + FROM SNMPv2-SMI + + MODULE-COMPLIANCE, OBJECT-GROUP + FROM SNMPv2-CONF + + TEXTUAL-CONVENTION, TruthValue, RowStatus, StorageType, + TimeStamp + FROM SNMPv2-TC + + InterfaceIndexOrZero + FROM IF-MIB -- [IFMIB] + + SnmpAdminString + FROM SNMP-FRAMEWORK-MIB -- [RFC3411] + + PerfCurrentCount, PerfIntervalCount + FROM PerfHist-TC-MIB + + -- Juniper Specific TDM MIB + jnxMibs + FROM JUNIPER-SMI -- *** JNX *** + + + jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex + FROM JUNIPER-VPN-MIB + + jnxPwTdmMibRoot + FROM JUNIPER-SMI; + + + + + jnxPWTdmMIB MODULE-IDENTITY + + LAST-UPDATED "200704030000Z" + ORGANIZATION "Pseudo-Wire Emulation Edge-to-Edge (PWE3) + Working Group" + CONTACT-INFO + " Orly Nicklass + Postal: RAD Data Communications + 24 Raoul Wallenberg St., Bldg C + Tel Aviv 69719, Israel + Email: orly_n@rad.com + + The PWE3 Working Group (email distribution pwe3@ietf.org, + http://www.ietf.org/html.charters/pwe3-charter.html) + " + + DESCRIPTION + "This MIB contains managed object definitions for + encapsulating TDM (T1,E1, T3, E3, NxDS0) as + pseudo-wires over packet-switching networks (PSN). + + This MIB supplements the PW-STD-MIB as in: Zelig, D., + Nadeau,T. 'Pseudo Wire (PW) Management Information Base'. + The PW-STD-MIB contains structures and MIB associations + generic to Pseudo-Wire (PW) emulation. PW-specific + MIBs (such as this) contain config and stats for specific + PW types. + + Copyright (C) The IETF Trust (2007). This version + of this MIB module is part of RFC yyyy; see the RFC + itself for full legal notices. + -- RFC Ed.: replace yyyy with actual RFC number & remove this + note" + + REVISION "200704030000Z" -- April 2007 + DESCRIPTION + "Initial version published as part of RFC YYYY." + -- RFC Editor: please replace YYYY with IANA assigned value, and + -- delete this note. + + ::= {jnxPwTdmMibRoot 1} --** JNX ** + + -- Local Textual conventions + JnxPwTDMCfgIndex ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "Index into the relevant pwXXXCfgTable." + SYNTAX Unsigned32 (1..4294967295) + + + JnxPwCfgIndexOrzero ::= TEXTUAL-CONVENTION + DISPLAY-HINT "d" + STATUS current + DESCRIPTION + "Index in any of the relevant configuration tables for + supplement information regarding configuration of the + specific technology. Value 0 implies no additional + configuration information is applicable." + SYNTAX Unsigned32 (0..4294967295) + + + + -- Tables, Scalars + jnxpwTDMObjects OBJECT IDENTIFIER ::= { jnxPWTdmMIB 1 } + -- Notifications + jnxpwTDMNotifications OBJECT IDENTIFIER ::= { jnxPWTdmMIB 2 } + -- Conformance + jnxpwTDMConformance OBJECT IDENTIFIER ::= { jnxPWTdmMIB 3 } + + -- TDM PW table + + jnxpwTDMTable OBJECT-TYPE + SYNTAX SEQUENCE OF JnxPwTDMEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table contains basic information including ifIndex, + and pointers to entries in the relevant TDM config + tables for this TDM PW." + ::= { jnxpwTDMObjects 1 } + + jnxpwTDMEntry OBJECT-TYPE + SYNTAX JnxPwTDMEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table is indexed by the same index that was + created for the associated entry in the PW Table + (in the PW-STD-MIB). + + - The PwIndex. + + An entry is created in this table by the agent for every + entry in the pwTable with a pwType equal to one of the + following: + e1Satop(17), t1Satop(18), e3Satop(19), t3Satop(20), + basicCesPsn(21), basicTdmIp(22), tdmCasCesPsn(23), + tdmCasTdmIp(24). + Unless otherwise specified, all RW objects in this table + MUST NOT be changed after row activation (see [PWMIB]) + and should remain unchanged after reboot." + + INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex } + + ::= { jnxpwTDMTable 1 } + + JnxPwTDMEntry ::= SEQUENCE { + + jnxpwTDMRate Integer32, + jnxpwTDMIfIndex InterfaceIndexOrZero, + jnxpwGenTDMCfgIndex JnxPwCfgIndexOrzero, + jnxpwRelTDMCfgIndex JnxPwCfgIndexOrzero, + + jnxpwTDMConfigError BITS, + jnxpwTDMTimeElapsed Integer32, + jnxpwTDMValidIntervals Integer32, + jnxpwTDMValidDayIntervals Integer32, + jnxpwTDMLastEsTimeStamp TimeStamp + } + + jnxpwTDMRate OBJECT-TYPE + SYNTAX Integer32 + -- MAX-ACCESS read-write + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The parameter represents the bit-rate of the TDM service + in multiples of the 'basic' 64 Kbit/s rate [TDMCP-EXT]. + It complements the definition of pwType used in + PW-STD-MIB. + For structure-agnostic the following should be used: + a) Satop E1 - 32 + b) Satop T1 emulation: + i) MUST be set to 24 in the basic emulation mode + ii) MUST be set to 25 for the 'Octet-aligned T1' + emulation mode + c) Satop E3 - 535 + d) Satop T3 - 699 + For all kinds of structure-aware emulation, this parameter + MUST be set to N where N is the number of DS0 channels + in the corresponding attachment circuit." + REFERENCE + "TDMCP-EXT" + DEFVAL { 32 } + ::= { jnxpwTDMEntry 1 } + + jnxpwTDMIfIndex OBJECT-TYPE + SYNTAX InterfaceIndexOrZero + -- MAX-ACCESS read-write + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This is a unique index within the ifTable. It represents + the interface index of the full link or the interface + index for the bundle holding the group of + time slots to be transmitted via this PW connection. + + A value of zero indicates an interface index that has yet + to be determined. + Once set, if the TDM ifIndex is (for some reason) later + removed, the agent SHOULD delete the associated PW rows + (e.g., this pwTDMTable entry). If the agent does not + delete the rows, the agent MUST set this object to + zero." + ::= { jnxpwTDMEntry 2 } + + jnxpwGenTDMCfgIndex OBJECT-TYPE + SYNTAX JnxPwCfgIndexOrzero + -- MAX-ACCESS read-write + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Index to the generic parameters in the TDM configuration + table that appears in this MIB module. It is likely that + multiple TDM PWs of the same characteristic will share + a single TDM Cfg entry." + ::= { jnxpwTDMEntry 3 } + + jnxpwRelTDMCfgIndex OBJECT-TYPE + SYNTAX JnxPwCfgIndexOrzero + -- MAX-ACCESS read-write + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Index to the relevant TDM configuration table entry + that appears in one of the related MIB modules + such as TDMoIP or CESoPSN. It is likely that + multiple TDM PWs of the same characteristic will share + a single configuration entry of the relevant type. + The value 0 implies no entry in other related MIB" + ::= { jnxpwTDMEntry 4 } + + jnxpwTDMConfigError OBJECT-TYPE + SYNTAX BITS { + notApplicable ( 0), + tdmTypeIncompatible ( 1), + peerRtpIncompatible ( 2), + peerPayloadSizeIncompatible ( 3) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Any of the bits are set if the local configuration is + not compatible with the peer configuration as available + from the various parameters options. Setting is done based + on signaling, or else value (0) will be set. + + -tdmTypeIncompatible bit is set if the local configuration + is not carrying the same TDM type as the peer configuration. + + -peerRtpIncompatible bit is set if the local configuration + is configured to send RTP packets for this PW, and the + remote is not capable of accepting RTP packets. + + -peerPayloadSizeIncompatible bit is set if the local + configuration is not carrying the same Payload Size as the + peer configuration. " + ::= { jnxpwTDMEntry 5} + + jnxpwTDMTimeElapsed OBJECT-TYPE + SYNTAX Integer32 (1..900) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of seconds, including partial seconds, + that have elapsed since the beginning of the current + measurement period. If, for some reason, such as an + adjustment in the system's time-of-day clock, the + current interval exceeds the maximum value, the + agent will return the maximum value." + ::= { jnxpwTDMEntry 6} + + jnxpwTDMValidIntervals OBJECT-TYPE + SYNTAX Integer32 (0..96) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of previous 15-minute intervals for which data + was collected. + An agent with TDM capability must be capable of supporting + at least n intervals. The minimum value of n is 4, The + default of n is 32 and the maximum value of n is 96. + The value will be n unless the measurement was (re-) + started within the last (n*15) minutes, in which case + the value will be the number of complete 15 minute + intervals for which the agent has at least some data. + In certain cases(e.g., in the case where the agent is + a proxy) it is possible that some intervals are unavailable. + In this case, this interval is the maximum interval number + for which data is available. " + ::= { jnxpwTDMEntry 7} + + jnxpwTDMValidDayIntervals OBJECT-TYPE + SYNTAX Integer32 (0..30) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of previous days for which data + was collected. + An agent with TDM capability must be capable of supporting + at least n intervals. The minimum value of n is 1, The + default of n is 1 and the maximum value of n is 30." + ::= { jnxpwTDMEntry 8} + + jnxpwTDMLastEsTimeStamp OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime at the most recent occasion at + which the TDM PW entered the ES or SES state." + ::= { jnxpwTDMEntry 11} + + + -- End of TDM PW table + + -- PW Generic TDM PW Configuration Table + + jnxpwTDMCfgIndexNext OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object contains the value to be used for + pwTDMCfgIndex when creating entries in the + pwTDMCfgTable. The value 0 indicates that no + unassigned entries are available. To obtain the + value of pwTDMCfgIndexNext for a new entry in the + pwTDMCfgTable, the manager issues a management + protocol retrieval operation. The agent will + determine through its local policy when this + index value will be made available for reuse." + + ::= { jnxpwTDMObjects 2 } + + jnxpwTDMCfgTable OBJECT-TYPE + SYNTAX SEQUENCE OF JnxPwTDMCfgEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table contains a set of parameters that may be + referenced by one or more TDM PWs in pwTDMTable." + + ::= { jnxpwTDMObjects 3 } + + jnxpwTDMCfgEntry OBJECT-TYPE + SYNTAX JnxPwTDMCfgEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "These parameters define the characteristics of a + TDM PW. They are grouped here to ease NMS burden. + Once an entry is created here it may be re-used + by many PWs. + Unless otherwise specified, all objects in this table + MUST NOT be changed after row activation (see [PWMIB]) + if the row index is in used by an entry in pwTDMTable. + Rows should remain unchanged after reboot." + + --INDEX { jnxpwTDMCfgIndex } + INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex } + + ::= { jnxpwTDMCfgTable 1 } + + JnxPwTDMCfgEntry ::= SEQUENCE { + jnxpwTDMCfgIndex JnxPwTDMCfgIndex, + jnxpwTDMCfgRowStatus RowStatus, + jnxpwTDMCfgPayloadSize Unsigned32, + jnxpwTDMCfgPktReorder TruthValue, + jnxpwTDMCfgRtpHdrUsed TruthValue, + jnxpwTDMCfgJtrBfrDepth Unsigned32, + jnxpwTDMCfgPayloadSuppression INTEGER, + + jnxpwTDMCfgConsecPktsInSynch Unsigned32, + jnxpwTDMCfgConsecMissPktsOutSynch Unsigned32, + jnxpwTDMCfgSetUp2SynchTimeOut Unsigned32, + + jnxpwTDMCfgPktReplacePolicy INTEGER, + + jnxpwTDMCfgAvePktLossTimeWindow Integer32, + jnxpwTDMCfgExcessivePktLossThreshold Unsigned32, + + jnxpwTDMCfgAlarmThreshold Unsigned32, + jnxpwTDMCfgClearAlarmThreshold Unsigned32, + + jnxpwTDMCfgMissingPktsToSes Unsigned32, + + jnxpwTDMCfgTimestampMode INTEGER, + jnxpwTDMCfgStorageType StorageType, + jnxpwTDMCfgPktFiller Unsigned32, + jnxpwTDMCfgName SnmpAdminString + } + + jnxpwTDMCfgIndex OBJECT-TYPE + SYNTAX JnxPwTDMCfgIndex + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Index to an entry in this table. The value is a copy of the + assigned pwTDMCfgIndexNext" + ::= { jnxpwTDMCfgEntry 1 } + + jnxpwTDMCfgRowStatus OBJECT-TYPE + SYNTAX RowStatus +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Object used for creating, modifying, and deleting + a row from this table. The following objects should not be + modified if the entry is in used and the status is active: + pwTDMCfgPayloadSize, pwTDMCfgRtpHdrUsed, + pwTDMCfgJtrBfrDepth, and pwTDMCfgPayloadSuppression. + The row should not be deleted if the entry is in used" + ::= { jnxpwTDMCfgEntry 2 } + + jnxpwTDMCfgPayloadSize OBJECT-TYPE + SYNTAX Unsigned32 +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of this object indicates the PayLoad Size (in bytes) + to be defined during the PW setUp. Upon TX, implementation + must be capable of carrying that amount of bytes. + Upon RX, when the LEN field is set to 0, the payload of + packet MUST assume this size, and if the actual + packet size is inconsistent with this length, + the packet MUST be considered to be malformed. " + ::= { jnxpwTDMCfgEntry 4 } + + jnxpwTDMCfgPktReorder OBJECT-TYPE + SYNTAX TruthValue +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If set True: as CE bound packets are queued in the + jitter buffer, out of order packets are re-ordered. The + maximum sequence number differential (i.e., the range in + which re-sequencing can occur) is dependant on the depth + of the jitter buffer. See pwTDMCfgJtrBfrDepth. + + NOTE: Some implementations may not support this feature. + The agent is then required to set this to False." + ::= { jnxpwTDMCfgEntry 5 } + + jnxpwTDMCfgRtpHdrUsed OBJECT-TYPE + SYNTAX TruthValue +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If set to False: an RTP header is not pre-pended to the + TDM packet." + REFERENCE + "SATOP" + DEFVAL { false } + ::= { jnxpwTDMCfgEntry 6 } + + jnxpwTDMCfgJtrBfrDepth OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "microsecond" +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The size of this buffer SHOULD be locally + configured to allow accommodation to the PSN-specific packet + delay variation. + + If configured to a value not supported by the + implementation, the agent MUST return an error code + 'jtrBfrDepth' in 'pwTDMConfigError ' + + NOTE: jitter buffers are a limited resource to + be managed. The actual size should be at least twice as big + as the value of pwTDMCfgJtrBfrDepth " + DEFVAL { 3000 } + + ::= { jnxpwTDMCfgEntry 7 } + + jnxpwTDMCfgPayloadSuppression OBJECT-TYPE + SYNTAX INTEGER + { + enable ( 1), + disable ( 2) + } +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Selecting 'enable' means: Payload suppression is allowed. + Payload MAY be omitted in order to conserve bandwidth. + Selecting 'disable' means: no suppresion under any + condition. + Object MAY be changed at any time." + DEFVAL { disable } + + ::= { jnxpwTDMCfgEntry 8 } + + jnxpwTDMCfgConsecPktsInSynch OBJECT-TYPE + SYNTAX Unsigned32 +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of consecutive packets with sequential + sequence numbers that are required to exit the + LOPS state. + Object MAY be changed when the related PW is + defined as not active." + REFERENCE + "SATOP" + DEFVAL { 2 } + ::= { jnxpwTDMCfgEntry 9 } + + jnxpwTDMCfgConsecMissPktsOutSynch OBJECT-TYPE + SYNTAX Unsigned32 +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of consecutive missing packets that are + required to enter the LOPS state. + Object MAY be changed when the related PW is + defined as not active." + REFERENCE + "SATOP" + DEFVAL { 10 } + ::= { jnxpwTDMCfgEntry 10 } + + jnxpwTDMCfgSetUp2SynchTimeOut OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "millisecond" +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The amount of time the host should wait before declaring the + pseudo wire in down state, if the number of consecutive + TDM packets that have been received after changing the + adminstrative status to up and after finalization of + signaling (if supported) between the two PEs is smaller + than pwTDMCfgConsecPktsInSynch. Once the the pw has + OperStatus of 'up' this parameter is no longer valid. This + parameter is defined to ensure that the host does not + prematurely inform failure of the pw. In particular pw 'down' + notifications should not be sent before expiration of this + timer. This parameter is valid only after adminisrative + changes of the status of the pw. If the pw fails due to + network impairments a 'down' notification should be sent. + Object MAY be changed when the related PW is + defined as not active." + DEFVAL {5000} + ::= { jnxpwTDMCfgEntry 11 } + + jnxpwTDMCfgPktReplacePolicy OBJECT-TYPE + SYNTAX INTEGER + { + allOnes (1), + implementationSpecific(2), + filler (3) --user defined + } +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This parameter determines the value to be played when CE bound + packets have over/underflow the jitter buffer, or are missing + for any reason. This byte pattern is sent(played)on + the TDM line. Selecting implementationSpecific(2) implies + agent specific algorithm. Selecting filler(3) requires setting + of pwTDMCfgPktFiller. + Object MAY be changed when the related PW is + defined as not active." + DEFVAL { allOnes } -- Play AIS + ::= { jnxpwTDMCfgEntry 12 } + + jnxpwTDMCfgAvePktLossTimeWindow OBJECT-TYPE + SYNTAX Integer32 + UNITS "millisecond" +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The length of time over which the average packet + loss rate should be computed to detect Excessive packet + loss rate. + Object MAY be changed when the related PW is + defined as not active." + ::= { jnxpwTDMCfgEntry 13} + + jnxpwTDMCfgExcessivePktLossThreshold OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "Percent" +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Excessive packet loss rate is detected by computing the + average packetloss rate over a pwTDMCfgAvePktLossTimeWindow + amount of time and comparing it with this threshold value. + The rate is expressed in precentage. + Object MAY be changed when the related PW is + defined as not active." + ::= { jnxpwTDMCfgEntry 14 } + + + jnxpwTDMCfgAlarmThreshold OBJECT-TYPE + SYNTAX Unsigned32 +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Alarms are only reported when the defect state persists + for the length of time specified by this object. + The object's unit is millisec. + Object MAY be changed when the related PW is + defined as not active." + DEFVAL { 2500 } + ::= { jnxpwTDMCfgEntry 15 } + + jnxpwTDMCfgClearAlarmThreshold OBJECT-TYPE + SYNTAX Unsigned32 +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Alarm MUST be cleared after the corresponding defect is + undetected for the amount of time specified by this object. + The object's unit is millisec. + Object MAY be changed when the related PW is + defined as not active." + DEFVAL { 10000 } + ::= { jnxpwTDMCfgEntry 16 } + + jnxpwTDMCfgMissingPktsToSes OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "Percent" +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Percent of missing packets detected (consecutive or not) + within a 1 second window to cause a Severely Error + Second (SES) to be counted. + Object MAY be changed when the related PW is + defined as not active." + DEFVAL { 30 } + ::= { jnxpwTDMCfgEntry 17 } + + jnxpwTDMCfgTimestampMode OBJECT-TYPE + SYNTAX INTEGER + { + notApplicable (1), + absolute (2), + differential (3) + } + +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Timestamp generation MAY be used in one of the following + modes: + 1. Absolute mode: the PSN-bound IWF sets timestamps + using the clock recovered from the incoming TDM attachment + circuit. As a consequence, the timestamps are closely + correlated with the sequence numbers. All TDM implementations + that support usage of the RTP header MUST support this mode. + 2. Differential mode: Both IWFs have access to a common high- + quality timing source, and this source is used for timestamp + generation. Support of this mode is OPTIONAL. + Object MAY be changed when the related PW is + defined as not active." + + ::= { jnxpwTDMCfgEntry 18 } + + jnxpwTDMCfgStorageType OBJECT-TYPE + SYNTAX StorageType +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This variable indicates the storage type for this + row." + ::= { jnxpwTDMCfgEntry 19 } + + jnxpwTDMCfgPktFiller OBJECT-TYPE + SYNTAX Unsigned32 (0..255) +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Filler byte pattern played out on the TDM + interface if pwTDMCfgPktReplacePolicy + was set to filler(3). + Object MAY be changed when the related PW is + defined as not active." + DEFVAL + { 255 } -- Play all ones, equal to AIS indications. + ::= { jnxpwTDMCfgEntry 20 } + + + jnxpwTDMCfgName OBJECT-TYPE + SYNTAX SnmpAdminString +-- MAX-ACCESS read-create + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A descriptive string, prefereably unique name, to an entry + in this table. + Object MAY be changed at any time." + ::= { jnxpwTDMCfgEntry 21 } + + -- END of Table + + -- The following counters work together to integrate + -- errors and the lack of errors on the TDM PW. An error is + -- caused by a missing packet. Missing packet can be a result + -- of: packet loss in the network, (uncorrectable) packet out + -- of sequence, packet length error, jitter buffer overflow, + -- and jitter buffer underflow. The result is declaring whether + -- or not the TDM PW is in Loss of Packet (LOPS) state. + + -- TDM PW Performance Current Table. + + jnxpwTDMPerfCurrentTable OBJECT-TYPE + SYNTAX SEQUENCE OF JnxPwTDMPerfCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The current 15 minute interval counts are in + this table. + + This table provides per TDM PW performance information." + + ::= { jnxpwTDMObjects 5 } + + jnxpwTDMPerfCurrentEntry OBJECT-TYPE + SYNTAX JnxPwTDMPerfCurrentEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table is created by the agent for every + pwTDMTable entry. After 15 minutes, the contents of this + table entry are copied to a new entry in the + pwTDMPerfInterval table and the counts in this entry + are reset to zero." + + -- INDEX { jnxpwIndex } + INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex } + + ::= { jnxpwTDMPerfCurrentTable 1 } + + JnxPwTDMPerfCurrentEntry ::= SEQUENCE { + + jnxpwTDMPerfCurrentMissingPkts PerfCurrentCount, + jnxpwTDMPerfCurrentPktsReOrder PerfCurrentCount, + jnxpwTDMPerfCurrentJtrBfrUnderruns PerfCurrentCount, + jnxpwTDMPerfCurrentMisOrderDropped PerfCurrentCount, + jnxpwTDMPerfCurrentMalformedPkt PerfCurrentCount, + + jnxpwTDMPerfCurrentESs PerfCurrentCount, + jnxpwTDMPerfCurrentSESs PerfCurrentCount, + jnxpwTDMPerfCurrentUASs PerfCurrentCount, + jnxpwTDMPerfCurrentFC PerfCurrentCount + } + + jnxpwTDMPerfCurrentMissingPkts OBJECT-TYPE + SYNTAX PerfCurrentCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of missing packets (as detected via control word + sequence number gaps)." + ::= { jnxpwTDMPerfCurrentEntry 1 } + + jnxpwTDMPerfCurrentPktsReOrder OBJECT-TYPE + SYNTAX PerfCurrentCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of packets detected out of sequence (via control + word sequence number), but successfully re-ordered. + Note: some implementations may not support this Feature." + ::= { jnxpwTDMPerfCurrentEntry 2 } + + + jnxpwTDMPerfCurrentJtrBfrUnderruns OBJECT-TYPE + SYNTAX PerfCurrentCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of times a packet needed to be played + out and the jitter buffer was empty." + ::= { jnxpwTDMPerfCurrentEntry 3 } + + jnxpwTDMPerfCurrentMisOrderDropped OBJECT-TYPE + SYNTAX PerfCurrentCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of packets detected out of order(via control word + sequence numbers), and could not be re-ordered, or could + not fit in the jitter buffer." + ::= { jnxpwTDMPerfCurrentEntry 4 } + + jnxpwTDMPerfCurrentMalformedPkt OBJECT-TYPE + SYNTAX PerfCurrentCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of packets detected with unexpected size, or + bad headers' stack" + ::= { jnxpwTDMPerfCurrentEntry 5 } + + jnxpwTDMPerfCurrentESs OBJECT-TYPE + SYNTAX PerfCurrentCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The counter associated with the number of Error + Seconds encountered. Any malformed packet, seq. error, LOPS + and similar are considered as error second" + ::= { jnxpwTDMPerfCurrentEntry 6 } + + jnxpwTDMPerfCurrentSESs OBJECT-TYPE + SYNTAX PerfCurrentCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The counter associated with the number of + Severely Error Seconds encountered. " + ::= { jnxpwTDMPerfCurrentEntry 7 } + + jnxpwTDMPerfCurrentUASs OBJECT-TYPE + SYNTAX PerfCurrentCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The counter associated with the number of + Unavailable Seconds encountered. Any consequtive + ten seconds of SES are counted as one UAS" + ::= { jnxpwTDMPerfCurrentEntry 8 } + + jnxpwTDMPerfCurrentFC OBJECT-TYPE + SYNTAX PerfCurrentCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "TDM Failure Counts (FC-TDM). The number of TDM failure + events. A failure event begins when the LOPS failure + is declared, and ends when the failure is cleared. A + failure event that begins in one period and ends in + another period is counted only in the period in which + it begins." + ::= { jnxpwTDMPerfCurrentEntry 9 } + + -- End TDM PW Performance Current Interval Table + + + -- TDM PW Performance Interval Table. + + jnxpwTDMPerfIntervalTable OBJECT-TYPE + SYNTAX SEQUENCE OF JnxPwTDMPerfIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table provides performance information per TDM PW + similar to the pwTDMPerfCurrentTable above. However, + these counts represent historical 15 minute intervals. + Typically, this table will have a maximum of 96 entries + for a 24 hour period, but is not limited to this. " + ::= { jnxpwTDMObjects 6 } + + jnxpwTDMPerfIntervalEntry OBJECT-TYPE + SYNTAX JnxPwTDMPerfIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table is created by the agent for + every pwTDMPerfCurrentEntry that is 15 minutes old. + The contents of the Current entry are copied to the new + entry here. The Current entry, then resets its counts + to zero for the next current 15 minute interval. " + + -- INDEX { jnxpwIndex, jnxpwTDMPerfIntervalNumber } + INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex , jnxpwTDMPerfIntervalNumber } + + ::= { jnxpwTDMPerfIntervalTable 1 } + + JnxPwTDMPerfIntervalEntry ::= SEQUENCE { + jnxpwTDMPerfIntervalNumber Unsigned32, + jnxpwTDMPerfIntervalValidData TruthValue, + jnxpwTDMPerfIntervalDuration Unsigned32, + + jnxpwTDMPerfIntervalMissingPkts PerfIntervalCount, + jnxpwTDMPerfIntervalPktsReOrder PerfIntervalCount, + jnxpwTDMPerfIntervalJtrBfrUnderruns PerfIntervalCount, + jnxpwTDMPerfIntervalMisOrderDropped PerfIntervalCount, + jnxpwTDMPerfIntervalMalformedPkt PerfIntervalCount, + + jnxpwTDMPerfIntervalESs PerfIntervalCount, + jnxpwTDMPerfIntervalSESs PerfIntervalCount, + jnxpwTDMPerfIntervalUASs PerfIntervalCount, + jnxpwTDMPerfIntervalFC PerfIntervalCount + } + + jnxpwTDMPerfIntervalNumber OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A number (normally between 1 and 96 to cover a 24 hour + period) which identifies the interval for which the set + of statistics is available. The interval identified by 1 + is the most recently completed 15 minute interval, and + the interval identified by N is the interval immediately + preceding the one identified by N-1. The minimum range of + N is 1 through 4. The default range is 1 through 32. The + maximum value of N is 1 through 96." + ::= { jnxpwTDMPerfIntervalEntry 1 } + + jnxpwTDMPerfIntervalValidData OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This variable indicates if the data for this interval + is valid." + ::= { jnxpwTDMPerfIntervalEntry 2 } + + jnxpwTDMPerfIntervalDuration OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The duration of a particular interval in seconds, + Adjustments in the system's time-of-day clock, may + cause the interval to be greater or less than, the + normal value. Therefore this actual interval value + is provided." + ::= { jnxpwTDMPerfIntervalEntry 3 } + + jnxpwTDMPerfIntervalMissingPkts OBJECT-TYPE + SYNTAX PerfIntervalCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of missing packets (as detected via control + word sequence number gaps)." + ::= { jnxpwTDMPerfIntervalEntry 4 } + + jnxpwTDMPerfIntervalPktsReOrder OBJECT-TYPE + SYNTAX PerfIntervalCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of packets detected out of sequence (via control + word sequence number), but successfully re-ordered. + Note: some implementations may not support this + Feature." + ::= { jnxpwTDMPerfIntervalEntry 5 } + + jnxpwTDMPerfIntervalJtrBfrUnderruns OBJECT-TYPE + SYNTAX PerfIntervalCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of times a packet needed to be played + out and the jitter buffer was empty." + ::= { jnxpwTDMPerfIntervalEntry 6 } + + jnxpwTDMPerfIntervalMisOrderDropped OBJECT-TYPE + SYNTAX PerfIntervalCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of packets detected out of order(via control word + sequence numbers), and could not be re-ordered, or could + not fit in the jitter buffer." + ::= { jnxpwTDMPerfIntervalEntry 7 } + + jnxpwTDMPerfIntervalMalformedPkt OBJECT-TYPE + SYNTAX PerfIntervalCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of packets detected with unexpected size, or + bad headers' stack" + ::= { jnxpwTDMPerfIntervalEntry 8 } + + + jnxpwTDMPerfIntervalESs OBJECT-TYPE + SYNTAX PerfIntervalCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The counter associated with the number of Error + Seconds encountered." + ::= { jnxpwTDMPerfIntervalEntry 9 } + + jnxpwTDMPerfIntervalSESs OBJECT-TYPE + SYNTAX PerfIntervalCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The counter associated with the number of + Severely Error Seconds encountered." + ::= { jnxpwTDMPerfIntervalEntry 10 } + + jnxpwTDMPerfIntervalUASs OBJECT-TYPE + SYNTAX PerfIntervalCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The counter associated with the number of + Unavailable Seconds encountered." + ::= { jnxpwTDMPerfIntervalEntry 11 } + + jnxpwTDMPerfIntervalFC OBJECT-TYPE + SYNTAX PerfIntervalCount + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "TDM Failure Counts (FC-TDM). The number of TDM failure + events. A failure event begins when the LOPS failure + is declared, and ends when the failure is cleared. A + failure event that begins in one period and ends in + another period is counted only in the period in which + it begins." + ::= { jnxpwTDMPerfIntervalEntry 12 } + + -- End TDM PW Performance Interval Table + + + -- TDM PW 1day Performance Table + + jnxpwTDMPerf1DayIntervalTable OBJECT-TYPE + SYNTAX SEQUENCE OF JnxPwTDMPerf1DayIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table provides performance information per TDM PW + similar to the pwTDMPerfIntervalTable above. However, + these counters represent historical 1 day intervals up to + one full month. The table consists of real time data, as + such it is not persistence across re-boot." + ::= { jnxpwTDMObjects 7 } + + jnxpwTDMPerf1DayIntervalEntry OBJECT-TYPE + SYNTAX JnxPwTDMPerf1DayIntervalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry is created in this table by the agent + for every entry in the pwTDMTable table." + + INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex, jnxpwTDMPerf1DayIntervalNumber } + + ::= { jnxpwTDMPerf1DayIntervalTable 1 } + + JnxPwTDMPerf1DayIntervalEntry ::= SEQUENCE { + jnxpwTDMPerf1DayIntervalNumber Unsigned32, + jnxpwTDMPerf1DayIntervalValidData TruthValue, + jnxpwTDMPerf1DayIntervalDuration Unsigned32, + jnxpwTDMPerf1DayIntervalMissingPkts Counter32, + jnxpwTDMPerf1DayIntervalPktsReOrder Counter32, + jnxpwTDMPerf1DayIntervalJtrBfrUnderruns Counter32, + jnxpwTDMPerf1DayIntervalMisOrderDropped Counter32, + jnxpwTDMPerf1DayIntervalMalformedPkt Counter32, + + jnxpwTDMPerf1DayIntervalESs Counter32, + jnxpwTDMPerf1DayIntervalSESs Counter32, + jnxpwTDMPerf1DayIntervalUASs Counter32, + jnxpwTDMPerf1DayIntervalFC Counter32 + } + + + jnxpwTDMPerf1DayIntervalNumber OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The number of interval, where 1 indicates current day + measured period and 2 and above indicate previous days + respectively" + ::= { jnxpwTDMPerf1DayIntervalEntry 1 } + + jnxpwTDMPerf1DayIntervalValidData OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This variable indicates if the data for this interval + is valid." + ::= { jnxpwTDMPerf1DayIntervalEntry 2 } + + jnxpwTDMPerf1DayIntervalDuration OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The duration of a particular interval in seconds, + Adjustments in the system's time-of-day clock, may + cause the interval to be greater or less than, the + normal value. Therefore this actual interval value + is provided." + ::= { jnxpwTDMPerf1DayIntervalEntry 3 } + + jnxpwTDMPerf1DayIntervalMissingPkts OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of missing packets (as detected via control word + sequence number gaps)." + ::= { jnxpwTDMPerf1DayIntervalEntry 4 } + + jnxpwTDMPerf1DayIntervalPktsReOrder OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of packets detected out of sequence (via control + word sequence number), but successfully re-ordered. + Note: some implementations may not support this + feature." + ::= { jnxpwTDMPerf1DayIntervalEntry 5 } + + jnxpwTDMPerf1DayIntervalJtrBfrUnderruns OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of times a packet needed to be played + out and the jitter buffer was empty." + ::= { jnxpwTDMPerf1DayIntervalEntry 6 } + + jnxpwTDMPerf1DayIntervalMisOrderDropped OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of packets detected out of order(via control word + sequence numbers), and could not be re-ordered, or could + not fit in the jitter buffer." + ::= { jnxpwTDMPerf1DayIntervalEntry 7 } + + jnxpwTDMPerf1DayIntervalMalformedPkt OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Number of packets detected with unexpected size, or + bad headers' stack." + ::= { jnxpwTDMPerf1DayIntervalEntry 8 } + + + jnxpwTDMPerf1DayIntervalESs OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The counter associated with the number of Error + Seconds encountered." + ::= { jnxpwTDMPerf1DayIntervalEntry 9 } + + jnxpwTDMPerf1DayIntervalSESs OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The counter associated with the number of Severely + Error Seconds." + ::= { jnxpwTDMPerf1DayIntervalEntry 10 } + + jnxpwTDMPerf1DayIntervalUASs OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The counter associated with the number of + UnAvailable Seconds. + + NOTE: When first entering the UAS state, the number + of SES To UAS is added to this object, then as each + additional UAS occurs, this object increments by one." + + ::= { jnxpwTDMPerf1DayIntervalEntry 11 } + + jnxpwTDMPerf1DayIntervalFC OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "TDM Failure Counts (FC-TDM). The number of TDM failure + events. A failure event begins when the LOPS failure + is declared, and ends when the failure is cleared." + ::= { jnxpwTDMPerf1DayIntervalEntry 12 } + + -- End of PW TDM Performance table + + -- Conformance Information + + + jnxpwTDMGroups OBJECT IDENTIFIER ::= { jnxpwTDMConformance 1 } + jnxpwTDMCompliances OBJECT IDENTIFIER ::= { jnxpwTDMConformance 2 } + + + jnxpwTDMModuleCompliance MODULE-COMPLIANCE + STATUS current + DESCRIPTION + "The compliance statement for agent that support TDM PW + over PSN operation." + + MODULE -- this module + MANDATORY-GROUPS { jnxpwTDMGroup, + jnxpwTDMPerfCurrentGroup, + jnxpwTDMPerfIntervalGroup, + jnxpwTDMPerf1DayIntervalGroup + } + + + OBJECT jnxpwGenTDMCfgIndex + MIN-ACCESS read-only + DESCRIPTION + "The ability to set the an index pointer + is not required." + + OBJECT jnxpwRelTDMCfgIndex + MIN-ACCESS read-only + DESCRIPTION + "The ability to set the an index pointer + is not required." + + OBJECT jnxpwTDMCfgPktReorder + MIN-ACCESS read-only + DESCRIPTION + "The ability to set the packet reordering + is not required." + + OBJECT jnxpwTDMCfgRtpHdrUsed + MIN-ACCESS read-only + DESCRIPTION + "The ability to set whether to use the + RTP header or not is not required." + + OBJECT jnxpwTDMCfgPayloadSuppression + MIN-ACCESS read-only + DESCRIPTION + "The ability to set this object is not + required." + + OBJECT jnxpwTDMCfgPktReplacePolicy + MIN-ACCESS read-only + DESCRIPTION + "The ability to set the replace policy + is not required." + + OBJECT jnxpwTDMCfgStorageType + MIN-ACCESS read-only + DESCRIPTION + "The ability to set the storage type is + not required." + + OBJECT jnxpwTDMCfgPktFiller + MIN-ACCESS read-only + DESCRIPTION + "The ability to set the Filler pattern + is not required." + OBJECT jnxpwTDMCfgName + MIN-ACCESS read-only + DESCRIPTION + "The ability to set the an Aliase + is not required." + + ::= { jnxpwTDMCompliances 1 } + + -- Units of conformance. + + jnxpwTDMGroup OBJECT-GROUP + OBJECTS { + jnxpwTDMRate, + jnxpwTDMIfIndex, + jnxpwGenTDMCfgIndex, + jnxpwRelTDMCfgIndex, + jnxpwTDMConfigError, + jnxpwTDMTimeElapsed, + jnxpwTDMValidIntervals, + jnxpwTDMValidDayIntervals, + + jnxpwTDMLastEsTimeStamp, + + jnxpwTDMCfgIndexNext, + + jnxpwTDMCfgRowStatus, + + jnxpwTDMCfgPayloadSize, + jnxpwTDMCfgPktReorder, + jnxpwTDMCfgRtpHdrUsed, + jnxpwTDMCfgJtrBfrDepth, + jnxpwTDMCfgPayloadSuppression, + jnxpwTDMCfgConsecPktsInSynch, + jnxpwTDMCfgConsecMissPktsOutSynch, + jnxpwTDMCfgSetUp2SynchTimeOut, + + jnxpwTDMCfgPktReplacePolicy, + + jnxpwTDMCfgAvePktLossTimeWindow , + jnxpwTDMCfgExcessivePktLossThreshold, + + jnxpwTDMCfgAlarmThreshold , + jnxpwTDMCfgClearAlarmThreshold, + jnxpwTDMCfgMissingPktsToSes, + + jnxpwTDMCfgTimestampMode, + jnxpwTDMCfgStorageType, + jnxpwTDMCfgPktFiller, + + jnxpwTDMCfgName + } + STATUS current + DESCRIPTION + "Collection of objects for basic TDM PW config and + status." + ::= { jnxpwTDMGroups 1 } + + jnxpwTDMPerfCurrentGroup OBJECT-GROUP + OBJECTS { + jnxpwTDMPerfCurrentMissingPkts, + jnxpwTDMPerfCurrentPktsReOrder, + jnxpwTDMPerfCurrentJtrBfrUnderruns, + jnxpwTDMPerfCurrentMisOrderDropped, + jnxpwTDMPerfCurrentMalformedPkt, + + jnxpwTDMPerfCurrentESs, + jnxpwTDMPerfCurrentSESs, + jnxpwTDMPerfCurrentUASs, + jnxpwTDMPerfCurrentFC + } + STATUS current + DESCRIPTION + "Collection of current statistics objects for TDM PWs." + ::= { jnxpwTDMGroups 2 } + + + jnxpwTDMPerfIntervalGroup OBJECT-GROUP + OBJECTS { + jnxpwTDMPerfIntervalValidData, + jnxpwTDMPerfIntervalDuration, + + jnxpwTDMPerfIntervalMissingPkts, + jnxpwTDMPerfIntervalPktsReOrder, + jnxpwTDMPerfIntervalJtrBfrUnderruns, + jnxpwTDMPerfIntervalMisOrderDropped, + jnxpwTDMPerfIntervalMalformedPkt, + + jnxpwTDMPerfIntervalESs, + jnxpwTDMPerfIntervalSESs, + jnxpwTDMPerfIntervalUASs, + jnxpwTDMPerfIntervalFC + + } + STATUS current + DESCRIPTION + "Collection of Interval statistics objects for TDM PWs." + ::= { jnxpwTDMGroups 3 } + + + jnxpwTDMPerf1DayIntervalGroup OBJECT-GROUP + OBJECTS { + jnxpwTDMPerf1DayIntervalValidData, + jnxpwTDMPerf1DayIntervalDuration, + jnxpwTDMPerf1DayIntervalMissingPkts, + jnxpwTDMPerf1DayIntervalPktsReOrder, + jnxpwTDMPerf1DayIntervalJtrBfrUnderruns, + jnxpwTDMPerf1DayIntervalMisOrderDropped, + jnxpwTDMPerf1DayIntervalMalformedPkt, + + jnxpwTDMPerf1DayIntervalESs, + jnxpwTDMPerf1DayIntervalSESs, + jnxpwTDMPerf1DayIntervalUASs, + jnxpwTDMPerf1DayIntervalFC + } + STATUS current + DESCRIPTION + "Collection of Daily statistics objects for TDM PWs." + ::= { jnxpwTDMGroups 4 } + + + + END -- cgit v1.2.3