From 98a672123c7872f6b9b75a9a2b6bb3aea504de6a Mon Sep 17 00:00:00 2001 From: David Leutgeb Date: Tue, 5 Dec 2023 12:25:34 +0100 Subject: Initial commit --- MIBS/cisco/CISCO-MVPN-MIB | 1223 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 1223 insertions(+) create mode 100644 MIBS/cisco/CISCO-MVPN-MIB (limited to 'MIBS/cisco/CISCO-MVPN-MIB') diff --git a/MIBS/cisco/CISCO-MVPN-MIB b/MIBS/cisco/CISCO-MVPN-MIB new file mode 100644 index 0000000..c404f62 --- /dev/null +++ b/MIBS/cisco/CISCO-MVPN-MIB @@ -0,0 +1,1223 @@ +-- ******************************************************************* +-- CISCO-MVPN-MIB.my: CISCO MULTICAST in BGP/MPLS VPNs MIB +-- +-- Copyright (c) 2004 by cisco Systems, Inc. +-- All rights reserved. +-- +-- ******************************************************************* + +-- Caution. This MIB is temporary and experimental. In the future it +-- will be removed from products, perhaps with short notice, in favor +-- of more standard or generic MIBs. Application developers should +-- not depend on long-term access to this MIB. + +CISCO-MVPN-MIB DEFINITIONS ::= BEGIN + +IMPORTS + MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Unsigned32 + FROM SNMPv2-SMI + + MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP + FROM SNMPv2-CONF + + TruthValue, RowStatus, TimeStamp, DisplayString, TimeInterval + FROM SNMPv2-TC + + ciscoExperiment + FROM CISCO-SMI + + ifIndex + FROM IF-MIB + + SnmpAdminString + FROM SNMP-FRAMEWORK-MIB + + InetAddress, InetAddressType + FROM INET-ADDRESS-MIB + + mplsVpnVrfName, MplsVpnRouteDistinguisher + FROM MPLS-VPN-MIB; + +ciscoMvpnMIB MODULE-IDENTITY + LAST-UPDATED "200402231200Z" -- 23 February 2004 12:00:00 GMT + ORGANIZATION "Cisco Systems, Inc." + CONTACT-INFO + " Cisco Systems, Inc. + 170 Tasman Drive + San Jose, CA 95134 + USA + + Tel: +1 800 553-NETS + + EMail: cs-ipmulticast@cisco.com" + + DESCRIPTION + "This MIB contains managed object definitions for + Cisco implementation of multicast in VPNs defined + by the Internet draft: draft-rosen-vpn-mcast-05.txt. + Note that this MIB works along with the + L3VPN-MPLS-VPN-MIB." + + -- Revision history. + REVISION "200402231200Z" -- 23 February 2004 12:00:00 GMT + DESCRIPTION + "Initial version." + ::= { ciscoExperiment 113 } + + +-- Definition of some terms used + +-- MVPN: Multicast VPN + +-- MVRF: Multicast VRF, a VRF which has multicast routing enabled +-- or has an interface that has PIM or IGMP protocol enabled. + +-- MDT: Multicast distribution tree. + +-- MD: Multicast domain. A multicast domain is a set of MVRFs that +-- are connected to the potential (but possibly inactive) sources and +-- receivers via CE interfaces. + +-- MDT group: Each MD is assigned a distinct group address from a +-- pool that is administered by the service provider(s). Such groups +-- reserved for MDs are called MDT groups. +-- MDT groups are used to encapsulate and transport multicast VPN +-- traffic within the corresponding MD. + +-- Default MDT/MDT-default: The MDT group used for forwarding MVPN +-- multicast data and PIM control traffic. Initially all MVPN +-- multicast data is forwarded using this group. This group is user +-- configured. + +-- Data MDT/MDT-data: Range of MDT group addresses that is created on +-- demand for specific MVPN groups. MVPN traffic that is initially +-- forwarded on the MDT-default can be moved to an MDT-data to +-- minimize flooding the other PE routers in the same MD. + +-- MDT Joins: When a MVPN multicast stream exceeds the threshold, a +-- PE device picks a group from the configured MDT-data pool and +-- advertises the (S,G,MDT-data) mapping to all PE routers in that +-- MVPN. The advertisements are done via UDP TLV messages and are +-- termed MDT joins. + +-- SSM: Source Specific Multicast. + +-- Multicast/MVPN Tunnel Interface: For every MD an MVRF is part of, +-- a PE router creates a special interface called the multicast/MVPN +-- tunnel interface. A multicast tunnel interface is the interface +-- an MVRF uses to access a MD. It can be thought of as conduit +-- that connects the MVRF and the global MVRF. + + +-- Top level components of this MIB. +ciscoMvpnNotifications OBJECT IDENTIFIER ::= { ciscoMvpnMIB 0 } +ciscoMvpnObjects OBJECT IDENTIFIER ::= { ciscoMvpnMIB 1 } +ciscoMvpnScalars OBJECT IDENTIFIER ::= { ciscoMvpnObjects 1 } +ciscoMvpnGeneric OBJECT IDENTIFIER ::= { ciscoMvpnObjects 2 } +ciscoMvpnConfig OBJECT IDENTIFIER ::= { ciscoMvpnObjects 3 } +ciscoMvpnProtocol OBJECT IDENTIFIER ::= { ciscoMvpnObjects 4 } +ciscoMvpnConformance OBJECT IDENTIFIER ::= { ciscoMvpnMIB 2 } + +-- Scalar Objects + +ciscoMvpnMvrfNumber OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of MVRFs that are present in this device." + ::= { ciscoMvpnScalars 1 } + +ciscoMvpnNotificationEnable OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "If this object is TRUE, then the generation of + all notifications defined in this MIB is enabled." + DEFVAL { false } + ::= { ciscoMvpnScalars 2 } + +-- Generic MVRF Information Table + +ciscoMvpnGenericTable OBJECT-TYPE + SYNTAX SEQUENCE OF CiscoMvpnGenericEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table gives the generic information about the MVRFs + present in this device." + ::= { ciscoMvpnGeneric 1 } + +ciscoMvpnGenericEntry OBJECT-TYPE + SYNTAX CiscoMvpnGenericEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table is created for every MVRF in the + device. + Note that many implementations may have MVRF for global + VRF (VRF0) by default in the device. + Also note that existence of the correspoding VRF in + L3VPN-MPLS-VPN-MIB is necessary for a row to exist in + this table. Deletion of corresponding VRF in + L3VPN-MPLS-VPN-MIB also results in deletion of a row here. + But deletion of a row ie deletion of a MVRF here does not + result in the deletion of the corresponding VRF in + L3VPN-MPLS-VPN-MIB." + INDEX { mplsVpnVrfName } + ::= { ciscoMvpnGenericTable 1 } + +CiscoMvpnGenericEntry ::= SEQUENCE { + ciscoMvpnGenOperStatusChange INTEGER, + ciscoMvpnGenOperChangeTime TimeStamp, + ciscoMvpnGenAssociatedInterfaces Unsigned32, + ciscoMvpnGenRowStatus RowStatus +} + +ciscoMvpnGenOperStatusChange OBJECT-TYPE + SYNTAX INTEGER { createdMvrf(1), + deletedMvrf(2), + modifiedMvrfDefMdtConfig(3), + modifiedMvrfDataMdtConfig(4) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object describes the last operational change that + happened for the given MVRF. + + createdMvrf - indicates that the MVRF was created in the + device. + + deletedMvrf - indicates that the MVRF was deleted from + the device. A row in this table will never have + ciscoMvpnGenOperStatusChange equal to deletedMvrf(2), + because in that case the row itself will be deleted + from the table. This value for + ciscoMvpnGenOperStatusChange is defined mainly for use + in ciscoMvpnMvrfChange notification. + + modifiedMvrfDefMdtConfig - indicates that the default MDT + group for the MVRF was configured, deleted or changed. + + modifiedMvrfDataMdtConfig - indicates that the data MDT + group range or a associated variable (like the threshold) + for the MVRF was configured, deleted or changed." + DEFVAL { createdMvrf } + ::= { ciscoMvpnGenericEntry 1 } + +ciscoMvpnGenOperChangeTime OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The time at which the last operational change for the + MVRF in question took place. The last operational change + is specified by ciscoMvpnGenOperStatusChange." + ::= { ciscoMvpnGenericEntry 2 } + +ciscoMvpnGenAssociatedInterfaces OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Total number of interfaces associated with this MVRF (including + the MDT tunnel interface) with ifOperStatus = up(1)." + ::= { ciscoMvpnGenericEntry 3 } + +ciscoMvpnGenRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This variable is used to create or delete a row in this table." + ::= { ciscoMvpnGenericEntry 4 } + +-- MDT-default group Configuration Table + +ciscoMvpnMdtDefaultTable OBJECT-TYPE + SYNTAX SEQUENCE OF CiscoMvpnMdtDefaultEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table specifies the default MDT address and the + encapsulation type used for a MVRF instance." + ::= { ciscoMvpnConfig 1 } + +ciscoMvpnMdtDefaultEntry OBJECT-TYPE + SYNTAX CiscoMvpnMdtDefaultEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table is created for every MVRF for which + a default MDT group is configured. A MVRF which does not + have a default MDT group configured will not appear in + this table. + Creation of a row in this table is the equivalent of + configuring default MDT address for the given MVRF. + Deletion of a row in this table is the equivalent of + deconfiguring default MDT address for the given MVRF." + INDEX { mplsVpnVrfName } + ::= { ciscoMvpnMdtDefaultTable 1 } + +CiscoMvpnMdtDefaultEntry ::= SEQUENCE { + ciscoMvpnMdtDefaultAddrType InetAddressType, + ciscoMvpnMdtDefaultAddress InetAddress, + ciscoMvpnMdtEncapsType INTEGER, + ciscoMvpnMdtDefaultRowStatus RowStatus +} + +ciscoMvpnMdtDefaultAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnMdtDefaultAddress." +::= { ciscoMvpnMdtDefaultEntry 1 } + +ciscoMvpnMdtDefaultAddress OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The default MDT address to be used for the MVRF in question." + ::= { ciscoMvpnMdtDefaultEntry 2 } + +ciscoMvpnMdtEncapsType OBJECT-TYPE + SYNTAX INTEGER { greIp (1), + ipIp (2), + mpls (3) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The encapsulation type to be used in the MVRF in question." + ::= { ciscoMvpnMdtDefaultEntry 3 } + +ciscoMvpnMdtDefaultRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This variable is used to create, modify or delete a + row in this table." + ::= { ciscoMvpnMdtDefaultEntry 4 } + +-- MDT-data configuration table + +ciscoMvpnMdtDataTable OBJECT-TYPE + SYNTAX SEQUENCE OF CiscoMvpnMdtDataEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table specifies the range of data MDT addresses and + associated variables for a MVRF instance." + ::= { ciscoMvpnConfig 2 } + +ciscoMvpnMdtDataEntry OBJECT-TYPE + SYNTAX CiscoMvpnMdtDataEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table is created for every MVRF for which + a data MDT group range is configured. A MVRF which does + not have a data MDT group range configured will not appear + in this table. + Creation of a row in this table is the equivalent of + configuring data MDT addresses for the given MVRF. Deletion + of a row in this table is the equivalent of deconfiguring + data MDT address usage in the given MVRF. + + Note that ciscoMvpnMdtDefaultEntry for a MVRF should be + present in the device before ciscoMvpnMdtDataEntry for + that MVRF can be created." + INDEX { mplsVpnVrfName } + ::= { ciscoMvpnMdtDataTable 1 } + +CiscoMvpnMdtDataEntry ::= SEQUENCE { + ciscoMvpnMdtDataRangeAddrType InetAddressType, + ciscoMvpnMdtDataRangeAddress InetAddress, + ciscoMvpnMdtDataWildcardType InetAddressType, + ciscoMvpnMdtDataWildcardBits InetAddress, + ciscoMvpnMdtDataThreshold Unsigned32, + ciscoMvpnMdtDataRowStatus RowStatus +} + +ciscoMvpnMdtDataRangeAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnMdtDataRangeAddress." + ::= { ciscoMvpnMdtDataEntry 1 } + +ciscoMvpnMdtDataRangeAddress OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The data MDT group range address for the given MVRF. + This along with ciscoMvpnMdtDataWildcardBits gives the + pool of data MDT addresses that can be used for + encapsulation in the MVRF upon data MDT switchover." + ::= { ciscoMvpnMdtDataEntry 2 } + +ciscoMvpnMdtDataWildcardType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnMdtDataWildcardBits." + ::= { ciscoMvpnMdtDataEntry 3 } + +ciscoMvpnMdtDataWildcardBits OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Wildcard bits which when used along with data MDT range + address, give a pool of addresses to be used in a MVRF. + + For example, if ciscoMvpnMdtDataRangeAddress is 239.1.2.0 + and ciscoMvpnMdtDataWildcardBits is 0.0.0.3, the possible + data MDT addresses are 239.1.2.0, 239.1.2.1, 239.1.2.2 + and 239.1.2.3. + + Note that wild card bits should be right contiguous." + ::= { ciscoMvpnMdtDataEntry 4 } + +ciscoMvpnMdtDataThreshold OBJECT-TYPE + SYNTAX Unsigned32 (0..4294967295) + UNITS "kilobits per second" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The bandwidth threshold value which when exceeded for a + multicast routing entry in the given MVRF, triggers usage + of data MDT address instead of default MDT address for + encapsulation." + ::= { ciscoMvpnMdtDataEntry 5 } + +ciscoMvpnMdtDataRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This variable is used to create, modify or delete a + row in this table." + ::= { ciscoMvpnMdtDataEntry 6 } + +-- MDT group info for a multicast route entry in question + +ciscoMvpnMrouteMdtTable OBJECT-TYPE + SYNTAX SEQUENCE OF CiscoMvpnMrouteMdtEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Given a multicast routing entry and the context MVRF, this + table provides information about the MDT group being used for + encapsulating the traffic for the multicast routing entry in + the provider network at the instance of querying. Note that + this table is a read-only table and is the result of the + default MDT and data MDT configurations and the operational + conditions like the traffic rate and sometimes, the + implementation choices." + ::= { ciscoMvpnProtocol 1 } + +ciscoMvpnMrouteMdtEntry OBJECT-TYPE + SYNTAX CiscoMvpnMrouteMdtEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table exists for a multicast routing entry + the traffic for which is being encapsulated in a context + MVRF." + INDEX { mplsVpnVrfName, + ciscoMvpnMrouteMvrfGrpAddrType, + ciscoMvpnMrouteMvrfGroup, + ciscoMvpnMrouteMvrfSrcAddrType, + ciscoMvpnMrouteMvrfSource, + ciscoMvpnMrouteUpDownStreamInfo } + ::= { ciscoMvpnMrouteMdtTable 1 } + +CiscoMvpnMrouteMdtEntry ::= SEQUENCE { + ciscoMvpnMrouteMvrfGrpAddrType InetAddressType, + ciscoMvpnMrouteMvrfGroup InetAddress, + ciscoMvpnMrouteMvrfSrcAddrType InetAddressType, + ciscoMvpnMrouteMvrfSource InetAddress, + ciscoMvpnMrouteUpDownStreamInfo INTEGER, + ciscoMvpnMrouteMdtGrpAddrType InetAddressType, + ciscoMvpnMrouteMdtGroup InetAddress, + ciscoMvpnMrouteMdtType INTEGER +} + +ciscoMvpnMrouteMvrfGrpAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnMrouteMvrfGroup." + ::= { ciscoMvpnMrouteMdtEntry 1 } + +ciscoMvpnMrouteMvrfGroup OBJECT-TYPE + SYNTAX InetAddress (SIZE (4|16|20)) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Group adddress of multicast routing entry in question." + ::= { ciscoMvpnMrouteMdtEntry 2 } + +ciscoMvpnMrouteMvrfSrcAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnMrouteMvrfSource." + ::= { ciscoMvpnMrouteMdtEntry 3 } + +ciscoMvpnMrouteMvrfSource OBJECT-TYPE + SYNTAX InetAddress (SIZE (4|16|20)) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Source adddress of the multicast routing entry in question." + ::= { ciscoMvpnMrouteMdtEntry 4 } + +ciscoMvpnMrouteUpDownStreamInfo OBJECT-TYPE + SYNTAX INTEGER { upstream (1), + downstream (2) + } + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Indicates if this PE is the upstream (sending) or the + downstream (receiving) router for the multicast routing entry + specified by ciscoMvpnMrouteMvrfSource and + ciscoMvpnMrouteMvrfGroup in the context MVRF specified by + mplsVpnVrfName. + Note that there may be two rows for the same multicast + routing entry if the traffic is bi-directional, one row + for PE as an upstream router the other for PE as the + downstream router." + ::= { ciscoMvpnMrouteMdtEntry 5 } + +ciscoMvpnMrouteMdtGrpAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnMrouteMdtGroup." + ::= { ciscoMvpnMrouteMdtEntry 6 } + +ciscoMvpnMrouteMdtGroup OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "MDT group address used to encapsulate the multicast routing + entry specified by ciscoMvpnMrouteMvrfSource and + ciscoMvpnMrouteMvrfGroup in the context MVRF specified by + mplsVpnVrfName." + ::= { ciscoMvpnMrouteMdtEntry 7 } + +ciscoMvpnMrouteMdtType OBJECT-TYPE + SYNTAX INTEGER { mdtDefault (1), + mdtData (2) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the type of MDT group used for encapsulation." + ::= { ciscoMvpnMrouteMdtEntry 8 } + +-- Table of BGP MDT Updates received + +ciscoMvpnBgpMdtUpdateTable OBJECT-TYPE + SYNTAX SEQUENCE OF CiscoMvpnBgpMdtUpdateEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table has information about the BGP advertisement of the + the MDT groups. (These advertisements are generated + and used for source discovery when SSM is used.)" + ::= { ciscoMvpnProtocol 2 } + +ciscoMvpnBgpMdtUpdateEntry OBJECT-TYPE + SYNTAX CiscoMvpnBgpMdtUpdateEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table is created when a BGP advertisement of + the MDT group is received and cached in the PE device. + An entry in this table deleted when such a cached BGP MDT + update is withdrawn." + INDEX { ciscoMvpnBgpMdtUpdGrpAddrType, + ciscoMvpnBgpMdtUpdateGroup, + ciscoMvpnBgpMdtUpdSrcAddrType, + ciscoMvpnBgpMdtUpdateSource } + ::= { ciscoMvpnBgpMdtUpdateTable 1 } + +CiscoMvpnBgpMdtUpdateEntry ::= SEQUENCE { + ciscoMvpnBgpMdtUpdGrpAddrType InetAddressType, + ciscoMvpnBgpMdtUpdateGroup InetAddress, + ciscoMvpnBgpMdtUpdateRd MplsVpnRouteDistinguisher, + ciscoMvpnBgpMdtUpdSrcAddrType InetAddressType, + ciscoMvpnBgpMdtUpdateSource InetAddress, + ciscoMvpnBgpMdtUpdOrigAddrType InetAddressType, + ciscoMvpnBgpMdtUpdateOriginator InetAddress, + ciscoMvpnBgpMdtUpdNhAddrType InetAddressType, + ciscoMvpnBgpMdtUpdateNexthop InetAddress + } + +ciscoMvpnBgpMdtUpdGrpAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnBgpMdtUpdateGroup." + ::= { ciscoMvpnBgpMdtUpdateEntry 1 } + +ciscoMvpnBgpMdtUpdateGroup OBJECT-TYPE + SYNTAX InetAddress (SIZE (4|16|20)) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "MDT group address in the BGP MDT advertisement." + ::= { ciscoMvpnBgpMdtUpdateEntry 2 } + +ciscoMvpnBgpMdtUpdateRd OBJECT-TYPE + SYNTAX MplsVpnRouteDistinguisher + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "RD (route distinguisher) in the BGP MDT advertisement. This + is the RD corresponding to the originator PE." + ::= { ciscoMvpnBgpMdtUpdateEntry 3 } + +ciscoMvpnBgpMdtUpdSrcAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnBgpMdtUpdateSource." + ::= { ciscoMvpnBgpMdtUpdateEntry 4 } + +ciscoMvpnBgpMdtUpdateSource OBJECT-TYPE + SYNTAX InetAddress (SIZE (4|16|20)) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "MDT source address in the BGP MDT advertisement." + ::= { ciscoMvpnBgpMdtUpdateEntry 5 } + +ciscoMvpnBgpMdtUpdOrigAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnBgpMdtUpdateOriginator." + ::= { ciscoMvpnBgpMdtUpdateEntry 6 } + +ciscoMvpnBgpMdtUpdateOriginator OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The BGP peering address of the device that originated (or + advertized) the BGP MDT update." + ::= { ciscoMvpnBgpMdtUpdateEntry 7 } + +ciscoMvpnBgpMdtUpdNhAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnBgpMdtUpdateNexthop." + ::= { ciscoMvpnBgpMdtUpdateEntry 8 } + +ciscoMvpnBgpMdtUpdateNexthop OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The next-hop address (address of the border router to be + used to reach the destination network) in the BGP MDT + advertisement." + ::= { ciscoMvpnBgpMdtUpdateEntry 9 } + +-- Table of MDT-data joins received + +ciscoMvpnMdtJnRcvTable OBJECT-TYPE + SYNTAX SEQUENCE OF CiscoMvpnMdtJnRcvEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table has information about the data MDT join TLVs + received by a device." + ::= { ciscoMvpnProtocol 3 } + +ciscoMvpnMdtJnRcvEntry OBJECT-TYPE + SYNTAX CiscoMvpnMdtJnRcvEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table is created or updated for every MDT + data join TLV received and cached in the device. The value of + mplsVpnVrfName in such an entry specifies the name of the + MVRF for which the data MDT groups from the TLVs are used." + INDEX { mplsVpnVrfName, + ciscoMvpnMdtJnRcvGrpAddrType, + ciscoMvpnMdtJnRcvGroup, + ciscoMvpnMdtJnRcvSrcAddrType, + ciscoMvpnMdtJnRcvSource } + ::= { ciscoMvpnMdtJnRcvTable 1 } + +CiscoMvpnMdtJnRcvEntry ::= SEQUENCE { + ciscoMvpnMdtJnRcvGrpAddrType InetAddressType, + ciscoMvpnMdtJnRcvGroup InetAddress, + ciscoMvpnMdtJnRcvSrcAddrType InetAddressType, + ciscoMvpnMdtJnRcvSource InetAddress, + ciscoMvpnMdtJnRcvUpTime TimeInterval, + ciscoMvpnMdtJnRcvExpTime TimeInterval + } + +ciscoMvpnMdtJnRcvGrpAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnMdtJnRcvGroup." + ::= { ciscoMvpnMdtJnRcvEntry 1 } + +ciscoMvpnMdtJnRcvGroup OBJECT-TYPE + SYNTAX InetAddress (SIZE (4|16|20)) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Data MDT group address in the MDT join TLV." + ::= { ciscoMvpnMdtJnRcvEntry 2 } + +ciscoMvpnMdtJnRcvSrcAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnMdtJnRcvSource." + ::= { ciscoMvpnMdtJnRcvEntry 3 } + +ciscoMvpnMdtJnRcvSource OBJECT-TYPE + SYNTAX InetAddress (SIZE (4|16|20)) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Source address for the MDT multicast routing entry created + following the receipt of MDT join TLV." + ::= { ciscoMvpnMdtJnRcvEntry 4 } + +ciscoMvpnMdtJnRcvUpTime OBJECT-TYPE + SYNTAX TimeInterval + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The time since this MDT join TLV was first received by the + device." + ::= { ciscoMvpnMdtJnRcvEntry 5 } + +ciscoMvpnMdtJnRcvExpTime OBJECT-TYPE + SYNTAX TimeInterval + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The amount of time remaining before the cache corresponding + to this MDT join TLV is deleted from the device and the + corresponding MDT multicast routing entry is marked as a + non-MDT entry. + Note that multiple TLVs for a data MDT group may be received + by a device. Upon receipt, the expiry timer of an already + existing entry is restarted and so ciscoMvpnMdtJnRcvExpTime + is updated." + ::= { ciscoMvpnMdtJnRcvEntry 6 } + +-- Table for MDT-data join TLVs sent + +ciscoMvpnMdtJnSendTable OBJECT-TYPE + SYNTAX SEQUENCE OF CiscoMvpnMdtJnSendEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table specifies the data MDT Join TLVs sent by a + device." + ::= { ciscoMvpnProtocol 4 } + +ciscoMvpnMdtJnSendEntry OBJECT-TYPE + SYNTAX CiscoMvpnMdtJnSendEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Entries in this table exist for data MDT Join TLVs that are + being sent by this device to other PEs." + INDEX { mplsVpnVrfName, + ciscoMvpnMdtJnSendGrpAddrType, + ciscoMvpnMdtJnSendGroup, + ciscoMvpnMdtJnSendSrcAddrType, + ciscoMvpnMdtJnSendSource } + ::= { ciscoMvpnMdtJnSendTable 1 } + +CiscoMvpnMdtJnSendEntry ::= SEQUENCE { + ciscoMvpnMdtJnSendGrpAddrType InetAddressType, + ciscoMvpnMdtJnSendGroup InetAddress, + ciscoMvpnMdtJnSendSrcAddrType InetAddressType, + ciscoMvpnMdtJnSendSource InetAddress, + ciscoMvpnMdtJnSendMdtGrpAddrType InetAddressType, + ciscoMvpnMdtJnSendMdtGroup InetAddress, + ciscoMvpnMdtJnSendMdtRefCt Unsigned32 + } + +ciscoMvpnMdtJnSendGrpAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnMdtJnSendGroup." + ::= { ciscoMvpnMdtJnSendEntry 1 } + +ciscoMvpnMdtJnSendGroup OBJECT-TYPE + SYNTAX InetAddress (SIZE (4|16|20)) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This indicates the address of a multicast group in the + MVRF specified by the column mplsVpnVrfName. This along + with ciscoMvpnMdtJnSendSource identifies the multicast + routing entry for which the MDT join TLV is sent." + ::= { ciscoMvpnMdtJnSendEntry 2 } + +ciscoMvpnMdtJnSendSrcAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnMdtJnSendSource." + ::= { ciscoMvpnMdtJnSendEntry 3 } + +ciscoMvpnMdtJnSendSource OBJECT-TYPE + SYNTAX InetAddress (SIZE (4|16|20)) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This indicates the address of a source in the MVRF + specified by the column mplsVpnVrfName. This, along with + ciscoMvpnMdtJnSendGroup identifies the multicast routing entry + for which the MDT join TLV is sent." + ::= { ciscoMvpnMdtJnSendEntry 4 } + +ciscoMvpnMdtJnSendMdtGrpAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The Internet address type of ciscoMvpnMdtJnSendMdtGroup." + ::= { ciscoMvpnMdtJnSendEntry 5 } + +ciscoMvpnMdtJnSendMdtGroup OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The data MDT group in the MDT Join TLV sent." + ::= { ciscoMvpnMdtJnSendEntry 6 } + +ciscoMvpnMdtJnSendMdtRefCt OBJECT-TYPE + SYNTAX Unsigned32 (0..65535) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates how many multicast routing entries in the MVRF + specified by the column mplsVpnVrfName are using + ciscoMvpnMdtJnSendMdtGroup for encapsulation." + ::= { ciscoMvpnMdtJnSendEntry 7 } + +-- Table of MVPN tunnel interfaces + +ciscoMvpnTunnelTable OBJECT-TYPE + SYNTAX SEQUENCE OF CiscoMvpnTunnelEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table gives information about the MVPN/MDT tunnels + present in the device." + ::= { ciscoMvpnProtocol 5 } + +ciscoMvpnTunnelEntry OBJECT-TYPE + SYNTAX CiscoMvpnTunnelEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table is created for every MVPN tunnel + interface present in the device. The ifType for a MVPN + tunnel is 'tunnel' (131). + (A MVPN tunnel interface should have relevant generic + support in the IF-MIB and in the internet draft, + draft-thaler-inet-tunnel-mib. Only MVPN specific aspects + of such a tunnel interface are to be specified in this + table.)" + INDEX { ifIndex } + ::= { ciscoMvpnTunnelTable 1 } + +CiscoMvpnTunnelEntry ::= SEQUENCE { + ciscoMvpnTunnelName DisplayString, + ciscoMvpnTunnelMvrf SnmpAdminString + } + +ciscoMvpnTunnelName OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The canonical name assigned to the tunnel. The ifName of + this tunnel interface should have a value equal to + ciscoMvpnTunnelName." + ::= { ciscoMvpnTunnelEntry 1 } + +ciscoMvpnTunnelMvrf OBJECT-TYPE + SYNTAX SnmpAdminString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Name of the MVRF that this tunnel is associated with. + This object has the same value as mplsVpnVrfName + for the MVRF." + ::= { ciscoMvpnTunnelEntry 2 } + +-- MVPN Notifications + +ciscoMvpnMvrfChange NOTIFICATION-TYPE + OBJECTS { + ciscoMvpnGenOperStatusChange + } + STATUS current + DESCRIPTION + "A ciscoMvpnMvrfChange notification signifies a change about + a MVRF in the device. The change event can be creation of + the MVRF, deletion of the MVRF or an update on the default + or data MDT configuration of the MVRF. The change event + is indicated by ciscoMvpnGenOperStatusChange embedded in + the notification. The user can then query + ciscoMvpnGenericTable, ciscoMvpnMdtDefaultTable and/or + ciscoMvpnMdtDataTable to get the details of the change as + necessary. + + Note: Since the creation of a MVRF is often followed by + configuration of default and data MDT groups for the MVRF, + more than one (three at most) notifications for a MVRF may + be generated serially, and it is really not necessary to + generate all three of them. An agent may choose to generate a + notification for the last event only, that is for data MDT + configuration. + + Similarly, deletion of default or data MDT configuration on a + MVRF happens before a MVRF is deleted, it is recommended + that the agent send the notification for MVRF deletion + event only." + ::= { ciscoMvpnNotifications 2 } + +-- Conformance information + +ciscoMvpnGroups + OBJECT IDENTIFIER ::= { ciscoMvpnConformance 1 } + +ciscoMvpnCompliances + OBJECT IDENTIFIER ::= { ciscoMvpnConformance 2 } + +-- Module Compliance + +ciscoMvpnModuleFullCompliance MODULE-COMPLIANCE + STATUS current + DESCRIPTION + "Compliance statement for agents that support read-create + so that both configuration and monitoring can be + accomplished via this MIB module." + MODULE -- this module + + MANDATORY-GROUPS { ciscoMvpnScalarGroup, + ciscoMvpnMIBGenericGroup, + ciscoMvpnMIBMdtDefaultGroup, + ciscoMvpnMIBMdtDataGroup, + ciscoMvpnMIBMrouteMdtGroup, + ciscoMvpnMIBBgpMdtUpdateGroup, + ciscoMvpnMIBMdtJnRcvGroup, + ciscoMvpnMIBMdtJnSendGroup, + ciscoMvpnTunnelGroup, + ciscoMvpnNotificationGroup + } + + OBJECT ciscoMvpnGenRowStatus + SYNTAX RowStatus + DESCRIPTION + "Support for notReady(3) and createAndWait(5) is + not required." + + OBJECT ciscoMvpnMdtDefaultAddrType + DESCRIPTION + "Not all Internet address types need to be supported." + + OBJECT ciscoMvpnMdtEncapsType + DESCRIPTION + "Not all encapsulation types defined need to be supported. + Only one type may be supported by default." + + OBJECT ciscoMvpnMdtDefaultRowStatus + SYNTAX RowStatus + DESCRIPTION + "Support for notReady(3) and createAndWait(5) is + not required." + + OBJECT ciscoMvpnMdtDataRangeAddrType + DESCRIPTION + "Not all Internet address types need to be supported." + + OBJECT ciscoMvpnMdtDataWildcardType + DESCRIPTION + "Not all Internet address types need to be supported." + + OBJECT ciscoMvpnMdtDataRowStatus + SYNTAX RowStatus + DESCRIPTION + "Support for notReady(3) and createAndWait(5) is + not required." + + OBJECT ciscoMvpnMrouteMdtGrpAddrType + DESCRIPTION + "Not all Internet address types need to be supported." + + OBJECT ciscoMvpnBgpMdtUpdOrigAddrType + DESCRIPTION + "Not all Internet address types need to be supported." + + OBJECT ciscoMvpnBgpMdtUpdNhAddrType + DESCRIPTION + "Not all Internet address types need to be supported." + + OBJECT ciscoMvpnMdtJnSendMdtGrpAddrType + DESCRIPTION + "Not all Internet address types need to be supported." + + ::= { ciscoMvpnCompliances 1 } + +ciscoMvpnModuleReadOnlyCompliance MODULE-COMPLIANCE + STATUS current + DESCRIPTION + "Compliance statement for agents that support the + monitoring of MVRFs via this MIB module." + MODULE -- this module + + MANDATORY-GROUPS { ciscoMvpnScalarGroup, + ciscoMvpnMIBGenericGroup, + ciscoMvpnMIBMdtDefaultGroup, + ciscoMvpnMIBMdtDataGroup, + ciscoMvpnMIBMrouteMdtGroup, + ciscoMvpnMIBBgpMdtUpdateGroup, + ciscoMvpnMIBMdtJnRcvGroup, + ciscoMvpnMIBMdtJnSendGroup, + ciscoMvpnTunnelGroup, + ciscoMvpnNotificationGroup + } + + OBJECT ciscoMvpnGenRowStatus + SYNTAX RowStatus + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required and active(1) is the + only status that needs to be supported." + + OBJECT ciscoMvpnMdtDefaultAddrType + MIN-ACCESS read-only + DESCRIPTION + "Not all Internet address types need to be supported. + Write access is not required." + + OBJECT ciscoMvpnMdtDefaultAddress + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ciscoMvpnMdtEncapsType + MIN-ACCESS read-only + DESCRIPTION + "Not all encapsulation types defined need to be supported. + Only one type may be supported by default. Write access + is not required." + + OBJECT ciscoMvpnMdtDefaultRowStatus + SYNTAX RowStatus + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required and active(1) is the + only status that needs to be supported." + + OBJECT ciscoMvpnMdtDataRangeAddrType + MIN-ACCESS read-only + DESCRIPTION + "Not all Internet address types need to be supported. + Write access is not required." + + OBJECT ciscoMvpnMdtDataRangeAddress + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ciscoMvpnMdtDataWildcardType + MIN-ACCESS read-only + DESCRIPTION + "Not all Internet address types need to be supported. + Write access is not required." + + OBJECT ciscoMvpnMdtDataWildcardBits + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ciscoMvpnMdtDataThreshold + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ciscoMvpnMdtDataRowStatus + SYNTAX RowStatus + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required and active(1) is the + only status that needs to be supported." + + OBJECT ciscoMvpnMrouteMdtGrpAddrType + DESCRIPTION + "Not all Internet address types need to be supported." + + OBJECT ciscoMvpnBgpMdtUpdOrigAddrType + DESCRIPTION + "Not all Internet address types need to be supported." + + OBJECT ciscoMvpnBgpMdtUpdNhAddrType + DESCRIPTION + "Not all Internet address types need to be supported." + + OBJECT ciscoMvpnMdtJnSendMdtGrpAddrType + DESCRIPTION + "Not all Internet address types need to be supported." + + ::= { ciscoMvpnCompliances 2 } + + -- Units of conformance. + + ciscoMvpnScalarGroup OBJECT-GROUP + OBJECTS { ciscoMvpnMvrfNumber, + ciscoMvpnNotificationEnable + } + STATUS current + DESCRIPTION + "Collection of scalar objects required for MVPN management." + ::= { ciscoMvpnGroups 1 } + + ciscoMvpnMIBGenericGroup OBJECT-GROUP + OBJECTS { ciscoMvpnGenOperStatusChange, + ciscoMvpnGenOperChangeTime, + ciscoMvpnGenAssociatedInterfaces, + ciscoMvpnGenRowStatus + } + STATUS current + DESCRIPTION + "Collection of objects needed for MVPN MVRF management." + ::= { ciscoMvpnGroups 2 } + + ciscoMvpnMIBMdtDefaultGroup OBJECT-GROUP + OBJECTS { ciscoMvpnMdtDefaultAddrType, + ciscoMvpnMdtDefaultAddress, + ciscoMvpnMdtEncapsType, + ciscoMvpnMdtDefaultRowStatus + } + STATUS current + DESCRIPTION + "Collection of objects needed for MVPN default MDT group + management." + ::= { ciscoMvpnGroups 3 } + + ciscoMvpnMIBMdtDataGroup OBJECT-GROUP + OBJECTS { ciscoMvpnMdtDataRangeAddrType, + ciscoMvpnMdtDataRangeAddress, + ciscoMvpnMdtDataWildcardType, + ciscoMvpnMdtDataWildcardBits, + ciscoMvpnMdtDataThreshold, + ciscoMvpnMdtDataRowStatus + } + STATUS current + DESCRIPTION + "Collection of objects needed for MVPN data MDT group + management." + ::= { ciscoMvpnGroups 4 } + + ciscoMvpnMIBMrouteMdtGroup OBJECT-GROUP + OBJECTS { ciscoMvpnMrouteMdtGrpAddrType, + ciscoMvpnMrouteMdtGroup, + ciscoMvpnMrouteMdtType + } + STATUS current + DESCRIPTION + "Collection of objects that list sources in a MVRF + and the corresponding MDT groups." + ::= { ciscoMvpnGroups 5 } + + ciscoMvpnMIBBgpMdtUpdateGroup OBJECT-GROUP + OBJECTS { ciscoMvpnBgpMdtUpdateRd, + ciscoMvpnBgpMdtUpdOrigAddrType, + ciscoMvpnBgpMdtUpdateOriginator, + ciscoMvpnBgpMdtUpdNhAddrType, + ciscoMvpnBgpMdtUpdateNexthop + } + STATUS current + DESCRIPTION + "Collection of objects needed for MVPN BGP MDT updates + related information." + ::= { ciscoMvpnGroups 6 } + + ciscoMvpnMIBMdtJnRcvGroup OBJECT-GROUP + OBJECTS { ciscoMvpnMdtJnRcvUpTime, + ciscoMvpnMdtJnRcvExpTime + } + STATUS current + DESCRIPTION + "Collection of objects needed for management of MVPN MDT + data joins received by a device." + ::= { ciscoMvpnGroups 7 } + + ciscoMvpnMIBMdtJnSendGroup OBJECT-GROUP + OBJECTS { ciscoMvpnMdtJnSendMdtGrpAddrType, + ciscoMvpnMdtJnSendMdtGroup, + ciscoMvpnMdtJnSendMdtRefCt + } + STATUS current + DESCRIPTION + "Collection of objects needed for management of MVPN MDT + data joins received by a device." + ::= { ciscoMvpnGroups 8 } + + ciscoMvpnTunnelGroup OBJECT-GROUP + OBJECTS { ciscoMvpnTunnelName, + ciscoMvpnTunnelMvrf + } + STATUS current + DESCRIPTION + "Objects required for MDT tunnel interface management." + ::= { ciscoMvpnGroups 9 } + + ciscoMvpnNotificationGroup NOTIFICATION-GROUP + NOTIFICATIONS { ciscoMvpnMvrfChange + } + STATUS current + DESCRIPTION + "A collection of MVPN notifications." + ::= { ciscoMvpnGroups 10 } + +-- End of CISCO-MVPN-MIB + +END -- cgit v1.2.3